# --------------------------------------------------------------------------
# A few practical configuration substitutions.
# --------------------------------------------------------------------------

substitutions:
  name: bedside_lamp
  friendly_name: Bedside Lamp
  transition_length: 500ms

  # Derive component identifiers, based on the name.
  id_light: ${name}
  id_light_mode: ${name}_light_mode
  id_power_button: ${name}_power_button
  id_color_button: ${name}_color_button
  id_slider_level: ${name}_slider_level
  id_front_panel_illumination: ${name}_front_panel_illumination

# --------------------------------------------------------------------------
# Use your own preferences for these components.
# --------------------------------------------------------------------------

wifi:
  ssid: "Your-SSID"
  password: "Your-WiFi-Network-Password"
  
  # Enable fallback hotspot (for captive portal) in case wifi connection fails
  ap:
    ssid: "ESPHome $friendly_name"
    password: "Password-For-Connecting-To-Captive-Portal"

captive_portal:

api:
  password: "Password-To-Link-HomeAssistant-To-This-Device"
  # Disable the reboot timeout. By default, the lamp reboots after 15
  # minutes without any client connections (e.g. when home assistant is off
  # line, or when the WiFi is broken). Reboots are annoying though, because
  # the RGBWW LEDs will turn off during the reboot, causing the light to
  # flicker.
  reboot_timeout: 0s

ota:
  password: "Password-For-Flashing-This-Device-Over-The-Air"

  # These OTA triggers are used to provide some visual feedback during the OTA
  # flashing process. The light is turned blue when the upgrade starts, the
  # brightness indicator will represent the update progress (fills up from 0%
  # to 100%), the light will flash red when the upgrade fails or green when the
  # upgrade succeeds.
  # You can safely remove these if you don't want the visual feedback.
  on_begin:
    then:
      - light.disco_on:
          id: ${id_light}
          red: 0%
          green: 0%
          blue: 100%
          brightness: 2%
          transition_length: 0s
  on_progress:
    then:
      - output.set_level:
          id: ${id_front_panel_illumination}
          level: !lambda return (x / 100.0f);
  on_end:
    then:
      - light.disco_on:
          id: ${id_light}
          red: 0%
          green: 100%
          blue: 0%
          brightness: 2%
          transition_length: 0s
  on_error:
    then:
      - light.disco_on:
          id: ${id_light}
          red: 100%
          green: 0%
          blue: 0%
          brightness: 2%
      - delay: 1s
      - light.disco_off:
          id: ${id_light}

# The log level can be raised when needed for debugging the firmware. For
# production, a low log level is recommended. Mainly because high volume log
# output might interfere with the API/WiFi connection stability. So when
# raising the log level, beware that you might see dropped connections from
# Home Assistant and the network log viewer.
logger:
    level: WARN

# --------------------------------------------------------------------------
# Configuration specific for the Xiaomi Mijia Bedside Lamp 2.
# This is just an example. You can of course modify it for your own needs.
# --------------------------------------------------------------------------

# Retrieve the code for the xiaomi_bslamp2 platform from GitHub.
external_components:
  - source:
      type: git
      url: https://github.com/mmakaay/esphome-xiaomi_bslamp2
      ref: main

# A special platform package is used for enabling unicore and disabling the
# efuse mac crc check. These two changes are required for the ESP32-WROOM-32D
# chip that is used in the lamp.
esphome:
  name: ${name}
  platform: ESP32
  board: esp32doit-devkit-v1
  platformio_options:
    platform: espressif32@3.2.0
    platform_packages: |-
      framework-arduinoespressif32 @ https://github.com/mmakaay/arduino-esp32-unicore-no-mac-crc#v1.0.6

# This component controls the LED lights of the lamp.
light:
  - platform: xiaomi_bslamp2
    id: ${id_light}
    name: ${friendly_name} RGBWW Light
    default_transition_length: ${transition_length}
    # When the brightness is changed, then update the level indicator
    # on the front panel accordingly. In night light mode, turn off
    # the front panel illumination.
    on_brightness:
      - if:
          condition:
            text_sensor.state:
                id: ${id_light_mode}
                state: night
          then:
            - output.set_level:
                id: ${id_front_panel_illumination}
                level: 0
          else:
            - output.set_level:
                id: ${id_front_panel_illumination}
                level: !lambda return x;
    # You can use any effects that you like. These are just examples.
    effects:
      - random:
          name: "Slow Random"
          transition_length: 30s
          update_interval: 30s
      - random:
          name: "Fast Random"
          transition_length: 3s
          update_interval: 3s
    # You can define one or more groups of presets. These presets can
    # be activated using various "preset.activate" action options.
    # The presets can for example be used to mimic the behavior of the
    # original firmware (tapping the color button = go to next preset,
    # holding the color button = switch between RGB and white light mode).
    # These bindings have been setup below, using the binary_sensor for
    # the color button.
    presets:
      rgb:
        red:         { red: 100%, green: 0%,   blue: 0%   }
        green:       { red: 0%,   green: 100%, blue: 0%   }
        blue:        { red: 0%,   green: 0%,   blue: 100% }
        yellow:      { red: 100%, green: 100%, blue: 0%   }
        purple:      { red: 100%, green: 0%,   blue: 100% }
        randomize:   { effect: Fast Random                }
      white:
        cold:        { color_temperature: 153 mireds      }
        chilly:      { color_temperature: 275 mireds      }
        luke:        { color_temperature: 400 mireds      }
        warm:        { color_temperature: 588 mireds      }

# This text sensor propagates the currently active light mode.
# The possible light modes are: "off", "rgb", "white" and "night".
# By setting the name, the text_sensor will show up as an entity
# for the lamp in Home Assistant.
text_sensor:
  - platform: xiaomi_bslamp2
    name: ${name} Light Mode
    id: ${id_light_mode}

# This float output controls the front panel illumination + level indicator.
# Value 0.0 turns off the illumination. Other values (up to 1.0) turn on
# the illumination and set the level indicator to the requested level.
output:
  - platform: xiaomi_bslamp2
    id: ${id_front_panel_illumination}

# Binary sensors can be created for handling front panel touch / release
# events. To specify what part of the front panel to look at, the "for"
# parameter can be set to: "POWER_BUTTON", "COLOR_BUTTON" or "SLIDER".
binary_sensor:
  # When tapping the power button, toggle the light.
  # When holding the power button, turn on night light mode.
  - platform: xiaomi_bslamp2
    id: ${id_power_button}
    for: POWER_BUTTON
    on_multi_click:
    - timing:
        - ON for at most 0.8s
      then:
        - light.toggle: ${id_light}
    - timing:
        - ON for at least 0.8s
      then:
        - light.turn_on:
            id: ${id_light}
            brightness: 1%

  # When tapping the color button, acivate the next preset.
  # When holding the color button, activate the next preset group.
  - platform: xiaomi_bslamp2
    id: ${id_color_button}
    for: COLOR_BUTTON
    on_multi_click:
      - timing:
          - ON for at most 0.6s
        then:
          - preset.activate:
              next: preset
      - timing:
          - ON for at least 0.6s
        then:
          - preset.activate:
              next: group

# This sensor component publishes touch events for the front panel slider.
# The published value represents the level at which the slider was touched.
# By default, values range from 0.01 to 1.00 (in 20 steps). This range can
# be modified using the "range_from" and "range_to" parameters.
sensor:
  # When the slider is touched, update the brightness.
  # Brightness 0.01 initiates the light night mode, which has already
  # been handled above (by holding the power button). Therefore, brightness
  # starts from 0.02 here, to not trigger night mode using the slider.
  - platform: xiaomi_bslamp2
    id: ${id_slider_level}
    range_from: 0.02
    on_value:
      then:
        - light.turn_on:
            id: ${id_light}
            brightness: !lambda return x;