abhas
/
esphome-xiaomi_bslamp2


								# --------------------------------------------------------------------------

								# A few practical configuration substitutions.

								# --------------------------------------------------------------------------


								substitutions:

								  name: bedside_lamp

								  friendly_name: Bedside Lamp

								  transition_length: 500ms


								  # Derive component identifiers, based on the name.

								  id_light: ${name}

								  id_front_panel_illumination: ${name}_front_panel_output

								  id_power_button: ${name}_power_button

								  id_color_button: ${name}_color_button

								  id_slider_level: ${name}_slider_level

								  id_light_mode: ${name}_light_mode


								# --------------------------------------------------------------------------

								# Use your own preferences for these components.

								# --------------------------------------------------------------------------


								wifi:

								  ssid: "Your-SSID"

								  password: "Your-WiFi-Network-Password"


								  # Enable fallback hotspot (for captive portal) in case wifi connection fails

								  ap:

								    ssid: "ESPHome $friendly_name"

								    password: "Password-For-Connecting-To-Captive-Portal"


								captive_portal:


								api:

								  password: "Password-To-Link-HomeAssistant-To-This-Device"


								ota:

								  password: "Password-For-Flashing-This-Device-Over-The-Air"


								# The log level can be raised when needed for debugging the firmware. For

								# production, a low log level is recommended. Mainly because high volume log

								# output might interfere with the API/WiFi connection stability. So when

								# raising the log level, beware that you might see dropped connections from

								# Home Assistant and the network log viewer.

								logger:

								    level: WARN


								# --------------------------------------------------------------------------

								# Configuration specific for the Xiaomi Mijia Bedside Lamp 2.

								# This is just an example. You can of course modify it for your own needs.

								# --------------------------------------------------------------------------


								# Special platform + package are used for enabling unicore and disabling the

								# efuse mac crc check. These two changes are required for the ESP32-WROOM-32D

								# chip that is used in the lamp.

								esphome:

								  name: ${name}

								  platform: ESP32

								  board: esp32doit-devkit-v1

								  platformio_options:

								    platform: espressif32@3.2.0

								    platform_packages: |-4

								        framework-arduinoespressif32 @ https://github.com/pauln/arduino-esp32.git#solo-no-mac-crc/1.0.6


								# This component controls the LED lights of the lamp.

								light:

								  - platform: xiaomi_bslamp2

								    id: ${id_light}

								    name: ${friendly_name} RGBW Light

								    default_transition_length: ${transition_length}

								    # When the brightness is changed, then update the level indicator

								    # on the front panel accordingly. In night light mode, turn off

								    # the front panel illumination.

								    on_brightness:

								      - if:

								          condition:

								            text_sensor.state:

								                id: ${id_light_mode}

								                state: night

								          then:

								            - output.set_level:

								                id: ${id_front_panel_illumination}

								                level: 0

								          else:

								            - output.set_level:

								                id: ${id_front_panel_illumination}

								                level: !lambda return x;

								    # You can use any effects that you like. These are just examples.

								    effects:

								      - random:

								          name: "Slow Random"

								          transition_length: 30s

								          update_interval: 30s

								      - random:

								          name: "Fast Random"

								          transition_length: 3s

								          update_interval: 3s

								    # You can define one or more groups of presets. These presets can

								    # be activated using various "preset.activate" action options.

								    # The presets can for example be used to mimic the behavior of the

								    # original firmware (tapping the color button = go to next preset,

								    # holding the color button = switch between RGB and white light mode).

								    # These bindings have been setup below, using the binary_sensor for

								    # the color button.

								    presets:

								      rgb:

								        red:         { red: 100%, green: 0%,   blue: 0%   }

								        green:       { red: 0%,   green: 100%, blue: 0%   }

								        blue:        { red: 0%,   green: 0%,   blue: 100% }

								        yellow:      { red: 100%, green: 100%, blue: 0%   }

								        purple:      { red: 100%, green: 0%,   blue: 100% }

								        randomize:   { effect: Fast Random                }

								      white:

								        cold:        { color_temperature: 153 mireds      }

								        chilly:      { color_temperature: 275 mireds      }

								        luke:        { color_temperature: 400 mireds      }

								        warm:        { color_temperature: 588 mireds      }


								# This text sensor propagates the currently active light mode.

								# The possible light modes are: "off", "rgb", "white" and "night".

								# By setting the name, the text_sensor will show up as an entity

								# for the lamp in Home Assistant.

								text_sensor:

								  - platform: xiaomi_bslamp2

								    name: ${name} Light Mode

								    id: ${id_light_mode}


								# This float output controls the front panel illumination + level indicator.

								# Value 0.0 turns off the illumination.

								# Other values (up to 1.0) turn on the illumination and set the level

								# indicator to the requested level.

								output:

								  - platform: xiaomi_bslamp2

								    id: ${id_front_panel_illumination}


								# Binary sensors can be created for handling front panel touch / release

								# events. To specify what part of the front panel to look at, the "part"

								# parameter can be set to: "any" (i.e. the default), "power button",

								# "color button" or "slider".

								binary_sensor:

								  # When tapping the power button, toggle the light.

								  # When holding the power button, turn on night light mode.

								  - platform: xiaomi_bslamp2

								    id: ${id_power_button}

								    part: power button

								    on_multi_click:

								    - timing:

								        - ON for at most 0.8s

								      then:

								        - light.toggle: ${id_light}

								    - timing:

								        - ON for at least 0.8s

								      then:

								        - light.turn_on:

								            id: ${id_light}

								            red: 1

								            green: 1

								            blue: 1

								            brightness: 0.01


								  # When tapping the color button, acivate the next preset.

								  # When holding the color button, activate the next preset group.

								  - platform: xiaomi_bslamp2

								    id: ${id_color_button}

								    part: color button

								    on_multi_click:

								      - timing:

								          - ON for at most 0.6s

								        then:

								          - preset.activate:

								              next: preset

								      - timing:

								          - ON for at least 0.6s

								        then:

								          - preset.activate:

								              next: group


								# This sensor component publishes touch events for the front panel slider.

								# The published value represents the level at which the slider was touched.

								# By default, values range from 0.01 to 1.00 (in 20 steps). This range can

								# be modified using the "range_from" and "range_to" parameters.

								sensor:

								  # When the slider is touched, update the brightness.

								  # Brightness 0.01 initiates the light night mode, which has already

								  # been handled above (by holding the power button). Therefore, brightness

								  # starts from 0.02 here, to not trigger night mode using the slider.

								  - platform: xiaomi_bslamp2

								    id: ${id_slider_level}

								    range_from: 0.02

								    on_value:

								      then:

								        - light.turn_on:

								            id: ${id_light}

								            brightness: !lambda return x;