One server implementation instead of two, plus simplify I/O operations
scheduling by processing everything in loop regardless of the server
type used.
Make it possible to accept authorization and several commands in a
single packet. If we fail the check, clients discards rest of the data.
Since we finally track connection state, debug info gets set *only* to
authorized clients.
- allow both new-pwm and analogWrite (Core) implementations
- rework new-pwm initialization, a bit more sane type for pin config
- remove pin setup from lights, everything is handled by provider already
Core prepares and initializes pins when updating duty, new-pwm does this
when pwm_init is called
- rework internals related to value scaling, allow percentage as pwm duty
and value limit (instead of absolute limit set by lights previously)
Attempt to either parse with newer syntax, or fallback to the floating
point seconds as default. Settings also return a 'result' instead of the
default zero, fallback to build value otherwise (which is still floating point, though)
Update /pulse API endpoint to report the actual pulse timer value that
is active right now, not just the value attached via the setting
- remove 'local' index and replace sensor code depending on it with the
existing 'slot' aka 'magnitude index' used in value() and type()
- common method to store and retrieve ratios for voltage, current,
active power and energy. default implementation is no-op, sensor
should implement ratio adjustment & calculations to use 'slot' indexes
- re-implement 'expected' values ui. display the actual ratio values,
and have a separate page for updating them in a more apparent way
- remove legacy settings that were adjusting expected values
- remove legacy settings that were resetting ratios and analog calibration
- generic webui action caller, add ratios and analog calibration resets
all of 'emon' sensors were updated to utilize the new approach to the
ratio handling. pulsemeter is somewhat an outlier, but it is unclear
whether removing the energy ratio is justified
terminal part was also updated
- implement `expected` command that hooks into the new ratioFromValue
(and what webui uses to calculate ratios)
- implement `energy` command to list only MAGNITUDE_ENERGY
- remove old pzem004t commands doing ratio reset and total energy count
another global update is related to espurna::duration
- rework module-local heartbeat and led durations into a global
espurna::duration
- update sensor internals to use specific units instead of multiplying things
on line-by-line basis. export count() to the api
Restore was unintentionally broken after switching from per-relay to
per-schedule setting. Instead of using schedules count it used the
number of relays (or curtains), and never light channels.
Instead, loop over available schedules and check the 'restore' flag,
calling the action when the schedule was supposed to be active.
Similar to the old approach, check for the most recent action and call
it (also, discarding the same type & target pairs, to avoid scheduling
conflicting actions)
time_t seconds offset is refactored into tm.tm_mday offset.
this causes the function to only work with local time, however
it *should* correctly offset day-by-day in case it somehow stumbles
upon dst transition
For settings:
- schSwitch renamed into schTarget
- schTarget default is no longer 0xff, but 0
- schType is a mandatory setting, instead of 1 (switch) default to 0 (none)
- move getSetting into functions to reduce code size
- delSetting case moved into the initial block that runs before restore() and check()
Plus, refactor C-style naming into namespaces similar to the other modules
- replace JustWifi with a custom WiFi module
- re-implemented Core methods that deal with scanning, directly work with the SDK callback
- re-implemented Core method for opmode to avoid dealing with the 2.7.x pseudo modes
- re-implemented Core method for forced-(modem)-sleep (with the intention to merge with OpmodeNull... todo)
- disable reconnect and autoconnect from SDK, avoid unintentionally storing ssid & pass for these and
make connection routine watch for events instead. timeout is implemented as a local timer
- do not store runtime data that can be retrieved via SDK calls
- settings are loaded only when starting AP or STA, networks are no longer kept in memory
- settings STA ssidN must be unique
- remove char buffer from the event callback
- trigger station-disconnected event when actually disconnected, not when connecting or explicitly requesting it
- generic rssi sorting method for initial connection, do rssi checks while connected to find a better network
Drop (temporarily?) wps and smartconfig. Both are implementable with the new approach,
but come with some weird expectations from the SDK side (no extra heap with wps, broadcasting plain-text
passphrase with smartconfig, storing station config implicitly, etc.).
Both are sort-of fixed with RTOS SDK, but it is still a big question of whether to support them at all in the current state.
Namespace build configurations of modules, make more things into constexpr
(not fully finished though)
Unify code using ...Count() to parse IDs
Avoid using unsigned char aka uint8_t as index, prefer size_t
as most code already uses it anyway. Making sure we never accidentally
truncate the value or try to read it as 32bit-wide. Also, simplify
access to built in containers, since those use the wide type as well.
Renames led and button types, more consistent initialization and field access.
- fix relay-id check breaking group topics
- group -> pub and sub topics
- wildcard in subscription topic will be properly handled
- make sure on disconnect event only triggers when mqtt is changing
state from connected to disconnected, don't trigger every failed re-try
- replace receive-only mode with separate sub and pub topics
- some more build time settings (and some... questionable code to handle that)
- shrink utils source file, move heartbeat and boot management into system
- improvise with 'heartbeat' functionality. include scheduler implementation that will
manage the per-module heartbeat callbacks with individual 'mode' and
'interval' settings. current ones are mqtt (including relays, lights, thermostat), debug and
influxdb. preserve heartbeat NONE, ONCE and REPEAT, REPEAT_STATUS is effectively a hbReport & status bit.
- mqtt heartbeat is managed through mqttHeartbeat() callbacks
- tweak mqtt callbacks to use lists instead of the vector, slighly reducing the size of the .bin
- update WebUI, include report setting and update hbMode values
- make sure general.h settings include new heartbeat,
move constant definitions outside of the header
- correctly include dependencies through the .cpp, avoid leaking
internal details.
- as a side-effect, base headers are no longer included recursively
- allow strings in mode (off, on, none)
- fixup type used for the mode to be am enum instead of int
(todo: allow webui to accept strings?)
- some cli updates using new funcs
update custom action callback to also get the event
buttons fan actions
ifan buttons are handled through action instead of manually
fan settings and api are (sort-of) generic
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
- provide a generic way to read default status of the pin after boot
allows us to use switch as both on and off, independent of the position on boot
- add BUTTON_DEFAULT_LOW & BUTTON_DEFAULT_BOOT (now it's not just BUTTON_DEFAULT_HIGH)
wiki described raw numbers for some reason :/ this will break that
- clean-up 'constexpr const' and 'const' function args, both are redundant
- clean-up debounce event member defaults, put things in the header
- Add ::Released button event to be used specifically with switches, opposite of ::Pressed
- Always use default state for switches instead of ignoring it and using current pin reading as value. This allows us to boot with the switch held in the opposite state and trigger the correct event immediately
(meaning, switches now depend on the BUTTON_DEFAULT_HIGH presence to detect the default position)
- BREAKING: Fixup hardware.h. Any custom board needs manual changes.
- BREAKING: Rework MQTT button messages to send text from debug messages instead of numeric code
- Buttons events source as button property instead of a global one
- Rename events source -> provider for all settings, consistent with the other things like relay and light providers
- AnalogPin to read between a certain analogRead() range
Trying to follow defaults here - analog 'press' is digital LOW, default value is HIGH, so no additional cfg entries are needed besides pin, level and changing evt source
- (debug) Refactor gpio command, add adc to show analogRead(pin)
- (debug) Add button command
Implemented based on:
https://gitter.im/tinkerman-cat/espurna?at=5f5d44c8df4af236f902e25dhttps://gitter.im/tinkerman-cat/espurna?at=5f60e7f1f969413294e95370
Add support for BME680 using libalgobsec proprietary algorithms for precise Indoor Air Quality (IAQ) measurement. Unlike traditional CO2 sensors - and good ones are expensive - it measures nearly all VOCs compounds in the air (plus other gases) and compensates those measurements with its built-in temperature and humidity sensors to determine indoor air quality.
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
- replace `apmode` with `wifiApMode`
- deprecate `WIFI_FALLBACK_APMODE` in favour of the AP mode setting
- allow to set custom SSID and passphrase for the softAP via `wifiApSsid` & `wifiApPass`
- identifier fallback for hostname
Add new V3.0 version of PZEM004T, not tested. Default to factory default address 0xf8, configurable through pzemv30Addr 8-bit number
Add 'frequency' measurement & 'hz' unit
Add pz.address that configures address
Implemented energy reset
Right now we only support a single device. No way to test this properly (mostly, how exactly we need to connect this stuff), so left as not implemented.
* Completed kingart curtain switch support:
Added Web UI controls and view in status
Added power up behaviour (nothing, close, open, last position)
Added curtain style (Roller, etc...) for UI status and to be used in MQTT
* Checked commit before PR. Added html gulp static files generated.
* Corrected a code refactor error which make the MQTT messages not handling position from received messages. Added comment to debug tab to show how to enable debug
* Use the maximum compression for gzip. A byte is a byte :)
* Update code/espurna/curtain_kingart.cpp
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
* Variable name prefix update
Added public set position function and curtain count
* Added Scheduler new type : curtain
* Add curtain schedule support and correct the 12h bug when adding a slot (00:00 after refresh). Default Hour is 12h
* Code cleaning.
Schedule support.
Light support is having an issue with new schedules corrected here.
* I let do better by the specialists
* Curtain init statues
* Coding style corrections
* Removed debug stuff from now - will be back later with the right way
* rebuild webui
* revert 435f1c5e03 schHour default, rebuild ui
Co-authored-by: Eric Chauvet <eric.chauvet@test-tree.com>
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
* ADC_VCC is not macro
* In esp.h ADC_VCC and ADC_TOUT is not macro, so define macro.
* ADC_VCC and ADC_TOUT fixes in utils.ino and sensors.h
* Adding support for I2C temperature and humidity sensor HDC1080 / 831R
* Added HDC1080 to test\build\sensor.h and arduino.h
* added brackets
* Revert ADC_MODE_VALUE to initial values
* Eof newline
* Eof newline
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
- Update sensor classes to support a generic way to store energy values
- Update sensor conversion code to deal with units and not magnitudes
- Add magnitude<->unit for sensors, generic way of defining used unit. Convert from sensor magnitude unit to the one used for display.
- Reset energy value based on index through external means (MQTT, HTTP)
- Rework energy timestamping, update webui with 'last saved' value
While this solves the energy conversion issues and we are finally seeing the real value, what I don't really like:
- KilowattHour and WattHour are separate enum tags, thus sort-of are different types altogether
- Conversion code in Energy object should probably use some generic 'ratio' calculation? (https://en.cppreference.com/w/cpp/numeric/ratio/ratio)
- We are still using runtime checks to do calculations and depend that sensor outputs only one specific value type.
Consider this a fix for energy display / storage and preliminary work on sensor.ino
Further sensor refactoring... soon.
* Fixes and updates for thermostat and display:
- Switch to original esp8266-oled-ssd1306 library
- Fixes and updates for thermostat and display
- Add display switching off after interval
- If THERMOSTAT_DISPLAY_SUPPORT enabled, then one click enable display, long click switch relay. This functionality also depend on fix for long click. See pull request https://github.com/xoseperez/espurna/pull/2172
* Move buttons definitions for display to dependencies.h
* Pin ThingPulse/esp8266-oled-ssd1306#3398c97
Maxim Prokhorov
hamed
Xose Pérez
Rui Marinho
dpeddi
Eric Chauvet
Alexander
DmitryBlinov