sys: clean-up system-specific functions
- shrink utils source file, move heartbeat and boot management into system
- improvise with 'heartbeat' functionality. include scheduler implementation that will
manage the per-module heartbeat callbacks with individual 'mode' and
'interval' settings. current ones are mqtt (including relays, lights, thermostat), debug and
influxdb. preserve heartbeat NONE, ONCE and REPEAT, REPEAT_STATUS is effectively a hbReport & status bit.
- mqtt heartbeat is managed through mqttHeartbeat() callbacks
- tweak mqtt callbacks to use lists instead of the vector, slighly reducing the size of the .bin
- update WebUI, include report setting and update hbMode values
- make sure general.h settings include new heartbeat,
move constant definitions outside of the header
- correctly include dependencies through the .cpp, avoid leaking
internal details.
- as a side-effect, base headers are no longer included recursively
3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago api: rework plain and JSON implementations (#2405)
- match paths through a custom AsyncWebHandler instead of using generic not-found fallback handler
- allow MQTT-like patterns when registering paths (`simple/path`, `path/+/something`, `path/#`)
Replaces `relay/0`, `relay/1` etc. with `relay/+`. Magnitudes are plain paths, but using `/+` in case there's more than 1 magnitude of the same type.
- restore `std::function` as callback container (no more single-byte arg nonsense). Still, limit to 1 type per handler type
- adds JSON handlers which will receive JsonObject root as both input and output. Same logic as plain - GET returns resource data, PUT updates it.
- breaking change to `apiAuthenticate(request)`, it no longer will do `request->send(403)` and expect this to be handled externally.
- allow `Api-Key` header containing the key, works for both GET & PUT plain requests. The only way to set apikey for JSON.
- add `ApiRequest::param` to retrieve both GET and PUT params (aka args), remove ApiBuffer
- remove `API_BUFFER_SIZE`. Allow custom form-data key=value pairs for requests, allow to send basic `String`.
- add `API_JSON_BUFFER_SIZE` for the JSON buffer (both input and output)
- `/apis` replaced with `/api/list`, no longer uses custom handler and is an `apiRegister` callback
- `/api/rpc` custom handler replaced with an `apiRegister` callback
WIP further down:
- no more `webLog` for API requests, unless `webAccessLog` / `WEB_ACCESS_LOG` is set to `1`. This also needs to happen to the other handlers.
- migrate to ArduinoJson v6, since it become apparent it is actually a good upgrade :)
- actually make use of JSON endpoints more, right now it's just existing GET for sensors and relays
- fork ESPAsyncWebServer to cleanup path parsing and temporary objects attached to the request (also, fix things a lot of things based on PRs there...) 4 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago providers: relays, lights and buttons refactoring (#2414)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve #2222 3 years ago |
|
- // -----------------------------------------------------------------------------
- // Lights
- // -----------------------------------------------------------------------------
-
- #pragma once
-
- #include "espurna.h"
-
- #define MQTT_TOPIC_LIGHT "light"
- #define MQTT_TOPIC_CHANNEL "channel"
- #define MQTT_TOPIC_COLOR_RGB "rgb"
- #define MQTT_TOPIC_COLOR_HSV "hsv"
- #define MQTT_TOPIC_ANIM_MODE "anim_mode"
- #define MQTT_TOPIC_ANIM_SPEED "anim_speed"
- #define MQTT_TOPIC_BRIGHTNESS "brightness"
- #define MQTT_TOPIC_MIRED "mired"
- #define MQTT_TOPIC_KELVIN "kelvin"
- #define MQTT_TOPIC_TRANSITION "transition"
-
- // TODO: lowercase
- namespace Light {
-
- constexpr size_t Channels = LIGHT_CHANNELS;
- constexpr size_t ChannelsMax = 5;
-
- constexpr long VALUE_MIN = LIGHT_MIN_VALUE;
- constexpr long VALUE_MAX = LIGHT_MAX_VALUE;
-
- constexpr long BRIGHTNESS_MIN = LIGHT_MIN_BRIGHTNESS;
- constexpr long BRIGHTNESS_MAX = LIGHT_MAX_BRIGHTNESS;
-
- constexpr long PWM_MIN = LIGHT_MIN_PWM;
- constexpr long PWM_MAX = LIGHT_MAX_PWM;
- constexpr long PWM_LIMIT = LIGHT_LIMIT_PWM;
-
- enum class Report {
- None = 0,
- Web = 1 << 0,
- Mqtt = 1 << 1,
- MqttGroup = 1 << 2,
- Broker = 1 << 3
- };
-
- constexpr int operator|(Report lhs, int rhs) {
- return static_cast<int>(lhs) | rhs;
- }
-
- constexpr int operator|(int lhs, Report rhs) {
- return lhs | static_cast<int>(rhs);
- }
-
- constexpr int operator|(Report lhs, Report rhs) {
- return static_cast<int>(lhs) | static_cast<int>(rhs);
- }
-
- constexpr int operator&(int lhs, Report rhs) {
- return lhs & static_cast<int>(rhs);
- }
-
- constexpr int operator&(Report lhs, int rhs) {
- return static_cast<int>(lhs) & rhs;
- }
-
- constexpr int DefaultReport {
- Report::Web | Report::Mqtt | Report::MqttGroup | Report::Broker
- };
-
- } // namespace Light
-
- using LightStateListener = std::function<void(bool)>;
-
- class LightProvider {
- public:
- virtual void update() = 0;
- virtual void state(bool) = 0;
- virtual void channel(unsigned char ch, double value) = 0;
- };
-
- struct LightTransition {
- unsigned long time;
- unsigned long step;
- };
-
- size_t lightChannels();
-
- LightTransition lightTransition();
-
- unsigned long lightTransitionTime();
- unsigned long lightTransitionStep();
-
- void lightTransition(unsigned long time, unsigned long step);
- void lightTransition(LightTransition transition);
-
- void lightColor(const char* color, bool rgb);
- void lightColor(const String& color, bool rgb);
-
- void lightColor(const String& color);
- void lightColor(const char* color);
-
- void lightColor(unsigned long color);
- String lightColor(bool rgb);
- String lightColor();
-
- bool lightSave();
- void lightSave(bool save);
-
- void lightState(unsigned char i, bool state);
- bool lightState(unsigned char i);
-
- void lightState(bool state);
- bool lightState();
-
- void lightBrightness(long brightness);
- long lightBrightness();
-
- long lightChannel(unsigned char id);
- void lightChannel(unsigned char id, long value);
-
- void lightBrightnessStep(long steps, long multiplier = LIGHT_STEP);
- void lightChannelStep(unsigned char id, long steps, long multiplier = LIGHT_STEP);
-
- void lightUpdate(bool save, LightTransition transition, Light::Report report);
- void lightUpdate(bool save, LightTransition transition, int report);
- void lightUpdate(LightTransition transition);
- void lightUpdate(bool save);
- void lightUpdate();
-
- bool lightHasColor();
- bool lightUseCCT();
-
- void lightMQTT();
-
- void lightSetStateListener(LightStateListener);
- void lightSetProvider(std::unique_ptr<LightProvider>&&);
- bool lightAdd();
-
- void lightSetup();
|