|
|
- # ESPurna Firmware
-
- ESPurna ("spark" in Catalan) is a custom firmware for ESP8266 based smart switches.
- It was originally developed with the **[IteadStudio Sonoff](https://www.itead.cc/sonoff-wifi-wireless-switch.html)** in mind but now it supports a growing number of ESP8266-based boards.
- It uses the Arduino Core for ESP8266 framework and a number of 3rd party libraries.
-
- **Current Release Version is 1.9.2**, read the [changelog](https://bitbucket.org/xoseperez/espurna/src/master/CHANGELOG.md).
-
- **NOTE**: since version 1.9.0 the default **MQTT topics for commands have changed**. They all now end with "/set". This means you will have to change your controller software (Node-RED or alike) to send messages to -for instance- "/home/living/light/relay/0/set". The device will publish its state in "/home/living/light/relay/0" like before.
-
- ## Features
-
- * Support for **multiple ESP8266-based boards** ([check list](https://bitbucket.org/xoseperez/espurna/wiki/Hardware))
- * Wifi **AP Mode** or **STA mode**
- * Up to 5 different networks can be defined
- * Supports static IP
- * Scans for strongest network if more than one defined
- * Defaults to AP mode (also available after double clicking the main button)
- * Switch management
- * Support for **push buttons** and **toggle switches**
- * Configurable **status on boot** (always ON, always OFF, same as before or toggle)
- * Support for **pulse mode** (normally ON or normally OFF) with configurable time
- * Support for **relay synchronization** (all equal, only one ON, one and only on ON)
- * Support for **delayed ON/OFF**
- * **MQTT** enabled
- * **SSL/TLS support** (not on regular builds, requires staging version of Arduino Core for ESP8266)
- * Switch on/off and toggle relays
- * Report button event notifications
- * Enable/disable pulse mode
- * Change LED notification mode
- * Remote reset the board
- * **Alexa** integration using the [FauxmoESP Library](https://bitbucket.org/xoseperez/fauxmoesp)
- * [**Domoticz**](https://domoticz.com/) integration via MQTT
- * [**Home Assistant**](https://home-assistant.io/) integration via MQTT
- * Supports MQTT auto-discover feature
- * [**InfluxDB**](https://www.influxdata.com/) integration via HTTP API
- * Support for different **sensors**
- * DHT11 / DHT22 / DHT21 / AM2301 (supports celsius & fahrenheit reporting)
- * DS18B20 (supports celsius & fahrenheit reporting)
- * HLW8012 using the [HLW8012 Library](https://bitbucket.org/xoseperez/hlw8012) (Sonoff POW)
- * Non-invasive current sensor using the [EmonLiteESP Library](https://bitbucket.org/xoseperez/emonliteesp) (requires some hacking)
- * Raw analog sensor
- * Fast asynchronous **HTTP Server**
- * Configurable port
- * Basic authentication
- * Web-based configuration
- * Relay switching and sensor data from the web interface
- * Handle color, brightness, and white/warm channels for lights
- * Websockets-based communication between the device and the browser
- * Backup and restore settings option
- * Upgrade firmware from the web interface
- * **REST API** (enable/disable from web interface)
- * GET and PUT relay status
- * Change light color (for supported hardware)
- * GET sensor data (power, current, voltage, temperature and humidity) depending on the available hardware
- * **RPC API** (enable/disable from web interface)
- * Remote reset the board
- * **Over-The-Air** (OTA) updates even for 1Mb boards
- * Manually from PlatformIO or Arduino IDE
- * Automatic updates through the [NoFUSS Library](https://bitbucket.org/xoseperez/nofuss)
- * Update from web interface using pre-built images
- * **Command line configuration**
- * Change configuration
- * Run special commands
- * **Telnet support**
- * Available only if connected to the AP interface
- * Show debug info and allows to run terminal commands
- * **Unstable system check**
- * Detects unstable system (crashes on boot continuously) and defaults to a stable system
- * Only WiFi AP, OTA and Telnet available if system is flagged as unstable
- * Button interface
- * Click to toggle relays
- * Double click to enter AP mode (only main button)
- * Long click (>1 second) to reboot device (only main button)
- * Extra long click (>10 seconds) to go back to factory settings (only main button)
-
- ## Documentation
-
- For more information please refer to the [ESPurna Wiki](https://bitbucket.org/xoseperez/espurna/wiki/Home).
-
- ## Supported hardware
-
- Here is the list of supported hardware. For more information please refer to the [ESPurna Wiki Hardware page](https://bitbucket.org/xoseperez/espurna/wiki/Hardware).
-
- ||||
- |---|---|---|
- ||||
- |**Tinkerman ESPurna H**|**IteadStudio Sonoff RF Bridge**||
- ||||
- |**IteadStudio Sonoff Basic**|**IteadStudio Sonoff RF**|**Electrodragon WiFi IOT**|
- ||||
- |**IteadStudio Sonoff Dual**|**IteadStudio Sonoff POW**|**IteadStudio Sonoff TH10/TH16**|
- ||||
- |**IteadStudio Sonoff 4CH**|**IteadStudio Sonoff 4CH Pro**|**OpenEnergyMonitor WiFi MQTT Relay / Thermostat**|
- ||||
- |**IteadStudio S20**|**WorkChoice EcoPlug**||
- ||||
- |**IteadStudio Sonoff Touch**|**IteadStudio Sonoff T1**||
- ||||
- |**IteadStudio Slampher**|**AI-Thinker Wifi Light / Noduino OpenLight**|**IteadStudio Sonoff B1**|
- ||||
- |**MagicHome LED Controller**|**Huacanxing H801**|**Itead BN-SZ01**|
- ||||
- |**IteadStudio Sonoff SV**|**IteadStudio 1CH Inching**|**IteadStudio Motor Clockwise/Anticlockwise**|
- ||||
- |**Wemos D1 Mini Relay Shield**|**Jan Goedeke Wifi Relay (NO/NC)**|**Jorge García Wifi + Relays Board Kit**|
- ||||
- |**EXS Wifi Relay v3.1**|||
-
- ## License
-
- Copyright (C) 2016-2017 by Xose Pérez (@xoseperez)
-
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
-
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
-
- You should have received a copy of the GNU General Public License
- along with this program. If not, see <http://www.gnu.org/licenses/>.
|
