Fork of the espurna firmware for `mhsw` switches
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

318 lines
9.8 KiB

providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
providers: relays, lights and buttons refactoring (#2414) - gpio module now tracks the known providers (right now, hardware and mcp expander) - refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions - refactored button module to use gpio provider instead of referencing types itself - removed dual & stm code from buttons, migrate both to relay module - added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did) - relays runtime configuration keys - relay command now shows configured relays and current & target statuses - refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead - remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT - allow to bind rf codes to real relays - drop tuya-specific lights provider, remove tuya code from relays and lights modules - integrate tuya via relay listeners and providers, use lights custom provider - implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle) - lights custom provider (global, not per-pin) and state listeners - remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT - lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT - refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing - transition time + step parameter for the lightUpdate - report mask parameter for the lightUpdate - minor fixes across the board resolve #2222
3 years ago
  1. #include <Arduino.h>
  2. #include <Stream.h>
  3. #include <unity.h>
  4. // -----------------------------------------------------------------------------
  5. // Tests
  6. // -----------------------------------------------------------------------------
  7. #include <type_traits>
  8. #include <queue>
  9. #include "libs/TypeChecks.h"
  10. #include "tuya_types.h"
  11. #include "tuya_util.h"
  12. #include "tuya_transport.h"
  13. #include "tuya_protocol.h"
  14. #include "tuya_dataframe.h"
  15. using namespace tuya;
  16. template <typename T>
  17. static bool datatype_same(const T& frame, const Type expect_type) {
  18. const auto type = dataType(frame);
  19. return expect_type == type;
  20. }
  21. void test_dpmap() {
  22. DpMap map;
  23. // id <-> dp
  24. map.add(1, 2);
  25. map.add(3, 4);
  26. map.add(5, 6);
  27. map.add(7, 8);
  28. TEST_ASSERT_EQUAL(4, map.size());
  29. map.add(7,10);
  30. map.add(5,5);
  31. // dpmap is a 'set' of values
  32. TEST_ASSERT_EQUAL(4, map.size());
  33. #define TEST_FIND_DP_ID(EXPECTED_DP_ID, EXPECTED_LOCAL_ID) \
  34. {\
  35. auto* entry = map.find_dp(EXPECTED_DP_ID);\
  36. TEST_ASSERT(entry != nullptr);\
  37. TEST_ASSERT_EQUAL(EXPECTED_DP_ID, entry->dp_id);\
  38. TEST_ASSERT_EQUAL(EXPECTED_LOCAL_ID, entry->local_id);\
  39. }
  40. TEST_FIND_DP_ID(2, 1);
  41. TEST_FIND_DP_ID(4, 3);
  42. TEST_FIND_DP_ID(6, 5);
  43. TEST_FIND_DP_ID(8, 7);
  44. #define TEST_FIND_LOCAL_ID(EXPECTED_LOCAL_ID, EXPECTED_DP_ID) \
  45. {\
  46. auto* entry = map.find_local(EXPECTED_LOCAL_ID);\
  47. TEST_ASSERT(entry != nullptr);\
  48. TEST_ASSERT_EQUAL(EXPECTED_DP_ID, entry->dp_id);\
  49. TEST_ASSERT_EQUAL(EXPECTED_LOCAL_ID, entry->local_id);\
  50. }
  51. TEST_FIND_LOCAL_ID(1, 2);
  52. TEST_FIND_LOCAL_ID(3, 4);
  53. TEST_FIND_LOCAL_ID(5, 6);
  54. TEST_FIND_LOCAL_ID(7, 8);
  55. #undef TEST_FIND_LOCAL_ID
  56. #undef TEST_FIND_DP_ID
  57. }
  58. void test_static_dataframe_bool() {
  59. DataFrame frame(Command::SetDP, DataProtocol<bool>(0x02, false).serialize());
  60. TEST_ASSERT_EQUAL_MESSAGE(0, frame.version(),
  61. "Version should stay 0 unless explicitly set");
  62. TEST_ASSERT_MESSAGE((frame.command() == Command::SetDP),
  63. "commandEquals should return true with the same arg as in the constructor");
  64. TEST_ASSERT_MESSAGE(datatype_same(frame, Type::BOOL),
  65. "DataProtocol<bool> should translate to Type::BOOL");
  66. }
  67. void test_static_dataframe_int() {
  68. DataFrame frame(Command::ReportDP, DataProtocol<uint32_t>(0x03, 255).serialize());
  69. TEST_ASSERT_EQUAL_MESSAGE(0, frame.version(),
  70. "Version should stay 0 unless explicitly set");
  71. TEST_ASSERT_MESSAGE((frame.command() == Command::ReportDP),
  72. "commandEquals should return true with the same arg as in the constructor");
  73. TEST_ASSERT_EQUAL_UINT_MESSAGE(std::distance(frame.cbegin(), frame.cend()), frame.length(),
  74. "Data is expected to be stored in a contigious memory and be equal in length to the ::length attribute");
  75. TEST_ASSERT_EQUAL_MESSAGE(0, frame[5],
  76. "Only last byte should be set");
  77. TEST_ASSERT_EQUAL_MESSAGE(255, frame[7],
  78. "Only last byte should be set");
  79. }
  80. void test_static_dataframe_heartbeat() {
  81. DataFrame frame(Command::Heartbeat);
  82. TEST_ASSERT_EQUAL_MESSAGE(0, frame.length(),
  83. "Frame with Command::Heartbeat should not have any data attached to it");
  84. TEST_ASSERT_EQUAL_MESSAGE(0, std::distance(frame.cbegin(), frame.cend()),
  85. "Frame with Command::SetDP should not have any data attached to it");
  86. //test_hexdump("static", static_frame.serialize());
  87. }
  88. void test_dataframe_const() {
  89. const DataFrame frame(Command::SetDP);
  90. TEST_ASSERT_EQUAL_MESSAGE(0, frame.length(),
  91. "Frame with Command::SetDP should not have any data attached to it");
  92. TEST_ASSERT_EQUAL_MESSAGE(0, std::distance(frame.cbegin(), frame.cend()),
  93. "Frame with Command::SetDP should not have any data attached to it");
  94. }
  95. void test_dataframe_copy() {
  96. DataFrame frame(Command::Heartbeat, 0x7f, container{1,2,3});
  97. DataFrame moved_frame(std::move(frame));
  98. TEST_ASSERT_EQUAL(3, moved_frame.length());
  99. TEST_ASSERT_EQUAL(3, moved_frame.length());
  100. TEST_ASSERT_EQUAL_MESSAGE(0x7f, moved_frame.version(),
  101. "DataFrame should be movable object");
  102. DataFrame copied_frame(moved_frame);
  103. TEST_ASSERT_EQUAL(3, copied_frame.length());
  104. TEST_ASSERT_EQUAL_MESSAGE(0x7f, copied_frame.version(),
  105. "DataFrame should not be copyable");
  106. }
  107. void test_dataframe_raw_data() {
  108. {
  109. container data = {0x00, 0x00, 0x00, 0x01, 0x01};
  110. DataFrameView frame(data);
  111. TEST_ASSERT_MESSAGE((frame.command() == Command::Heartbeat),
  112. "This message should be parsed as heartbeat");
  113. TEST_ASSERT_EQUAL_MESSAGE(0, frame.version(),
  114. "This message should have version == 0");
  115. TEST_ASSERT_EQUAL_MESSAGE(1, frame.length(),
  116. "Heartbeat message contains a single byte");
  117. TEST_ASSERT_EQUAL_MESSAGE(1, frame[0],
  118. "Heartbeat message contains a single 0x01");
  119. auto serialized = frame.serialize();
  120. TEST_ASSERT_MESSAGE(std::equal(data.begin(), data.end(), serialized.begin()),
  121. "Serialized frame should match the original data");
  122. }
  123. {
  124. container data = {0x00, 0x07, 0x00, 0x05, 0x01, 0x01, 0x00, 0x01, 0x01};
  125. DataFrameView frame(data);
  126. TEST_ASSERT_MESSAGE((frame.command() == Command::ReportDP),
  127. "This message should be parsed as data protocol");
  128. TEST_ASSERT_MESSAGE(datatype_same(frame, Type::BOOL),
  129. "This message should have boolean datatype attached to it");
  130. TEST_ASSERT_EQUAL_MESSAGE(5, frame.length(),
  131. "Boolean DP contains 5 bytes");
  132. const DataProtocol<bool> dp(frame.data());
  133. TEST_ASSERT_EQUAL_MESSAGE(1, dp.id(), "This boolean DP id should be 1");
  134. TEST_ASSERT_MESSAGE(dp.value(), "This boolean DP value should be true");
  135. auto serialized = frame.serialize();
  136. TEST_ASSERT_MESSAGE(std::equal(data.begin(), data.end(), serialized.begin()),
  137. "Serialized frame should match the original data");
  138. }
  139. //show_datatype(frame);
  140. //std::cout << "length=" << frame.length << std::endl;
  141. //test_hexdump("input", frame.serialize());
  142. //std::cout << "[" << millis() << "] -------------------bad dp frame----------------" << std::endl;
  143. //DataFrame bad_dp_frame(Command::ReportDP, DataProtocol<uint32_t>(0x03, 255).serialize());
  144. //show_datatype(bad_dp_frame);
  145. //std::cout << "length=" << bad_dp_frame.length << std::endl;
  146. //test_hexdump("input", bad_dp_frame.serialize());
  147. }
  148. class BufferedStream : public Stream {
  149. public:
  150. // Print interface
  151. size_t write(uint8_t c) {
  152. _buffer.push((int)c);
  153. return 1;
  154. }
  155. size_t write(const unsigned char* data, unsigned long size) {
  156. for (size_t n = 0; n < size; ++n) {
  157. _buffer.push(data[n]);
  158. }
  159. return size;
  160. }
  161. int availableForWrite() { return 1; }
  162. void flush() {
  163. while (!_buffer.empty()) {
  164. _buffer.pop();
  165. }
  166. }
  167. // Stream interface
  168. int available() {
  169. return _buffer.size();
  170. }
  171. int read() {
  172. if (!_buffer.size()) return -1;
  173. int c = _buffer.front();
  174. _buffer.pop();
  175. return c;
  176. }
  177. int peek() {
  178. if (!_buffer.size()) return -1;
  179. return _buffer.front();
  180. }
  181. private:
  182. std::queue<int> _buffer;
  183. };
  184. void test_transport() {
  185. container data = {0x55, 0xaa, 0x00, 0x00, 0x00, 0x01, 0x01, 0x01};
  186. BufferedStream stream;
  187. stream.write(data.data(), data.size());
  188. Transport transport(stream);
  189. TEST_ASSERT(transport.available());
  190. for (size_t n = 0; n < data.size(); ++n) {
  191. transport.read();
  192. }
  193. TEST_ASSERT(transport.done());
  194. }
  195. void test_dataframe_report() {
  196. container input = {0x55, 0xaa, 0x00, 0x07, 0x00, 0x08, 0x02, 0x02, 0x00, 0x04, 0x00, 0x00, 0x00, 0x10, 0x26};
  197. BufferedStream stream;
  198. stream.write(input.data(), input.size());
  199. Transport transport(stream);
  200. while (transport.available()) {
  201. transport.read();
  202. }
  203. TEST_ASSERT(transport.done());
  204. DataFrameView frame(transport);
  205. TEST_ASSERT(frame.command() == Command::ReportDP);
  206. TEST_ASSERT_EQUAL(Type::INT, dataType(frame));
  207. TEST_ASSERT_EQUAL(8, frame.length());
  208. TEST_ASSERT_EQUAL(0, frame.version());
  209. DataProtocol<uint32_t> proto(frame.data());
  210. TEST_ASSERT_EQUAL(0x02, proto.id());
  211. TEST_ASSERT_EQUAL(0x10, proto.value());
  212. }
  213. void test_dataframe_echo() {
  214. BufferedStream stream;
  215. Transport transport(stream);
  216. {
  217. DataProtocol<uint32_t> proto(0x02, 0x66);
  218. TEST_ASSERT_EQUAL(0x02, proto.id());
  219. TEST_ASSERT_EQUAL(0x66,proto.value());
  220. DataFrame frame(Command::SetDP, proto.serialize());
  221. transport.write(frame.serialize());
  222. }
  223. while (transport.available()) {
  224. transport.read();
  225. }
  226. TEST_ASSERT(transport.done());
  227. {
  228. DataFrameView frame(transport);
  229. TEST_ASSERT(frame.command() == Command::SetDP);
  230. TEST_ASSERT_EQUAL(Type::INT, dataType(frame));
  231. TEST_ASSERT_EQUAL(8, frame.length());
  232. TEST_ASSERT_EQUAL(0, frame.version());
  233. DataProtocol<uint32_t> proto(frame.data());
  234. TEST_ASSERT_EQUAL(0x02, proto.id());
  235. TEST_ASSERT_EQUAL(0x66, proto.value());
  236. }
  237. }
  238. int main(int argc, char** argv) {
  239. UNITY_BEGIN();
  240. RUN_TEST(test_dpmap);
  241. RUN_TEST(test_static_dataframe_bool);
  242. RUN_TEST(test_static_dataframe_int);
  243. RUN_TEST(test_static_dataframe_heartbeat);
  244. RUN_TEST(test_dataframe_const);
  245. RUN_TEST(test_dataframe_copy);
  246. RUN_TEST(test_dataframe_raw_data);
  247. RUN_TEST(test_dataframe_report);
  248. RUN_TEST(test_dataframe_echo);
  249. RUN_TEST(test_transport);
  250. return UNITY_END();
  251. }