mh
/
mhsw-espurna

// -----------------------------------------------------------------------------
// SENSORS
// -----------------------------------------------------------------------------

#define SENSOR_READ_INTERVAL            6000            // Read data from sensors every 6 seconds
#define SENSOR_REPORT_EVERY             10              // Report every this many readings
#define SENSOR_USE_INDEX                0               // Use the index in topic (i.e. temperature/0)
                                                        // even if just one sensor (0 for backwards compatibility)

#ifndef SENSOR_TEMPERATURE_UNITS
#define SENSOR_TEMPERATURE_UNITS        TMP_CELSIUS     // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)
#endif

#ifndef SENSOR_TEMPERATURE_CORRECTION
#define SENSOR_TEMPERATURE_CORRECTION   0.0             // Offset correction
#endif

#ifndef TEMPERATURE_MIN_CHANGE
#define TEMPERATURE_MIN_CHANGE          0.0             // Minimum temperature change to report
#endif

#ifndef HUMIDITY_MIN_CHANGE
#define HUMIDITY_MIN_CHANGE             0               // Minimum humidity change to report
#endif

#define SENSOR_TEMPERATURE_DECIMALS     1
#define SENSOR_HUMIDITY_DECIMALS        0
#define SENSOR_PRESSURE_DECIMALS        2
#define SENSOR_ANALOG_DECIMALS          0
#define SENSOR_EVENTS_DECIMALS          0
#define SENSOR_CURRENT_DECIMALS         3
#define SENSOR_VOLTAGE_DECIMALS         0
#define SENSOR_POWER_DECIMALS           0
#define SENSOR_POWER_FACTOR_DECIMALS    0
#define SENSOR_ENERGY_DECIMALS          0
#define SENSOR_PM1dot0_DECIMALS         0
#define SENSOR_PM2dot5_DECIMALS         0
#define SENSOR_PM10_DECIMALS            0
#define SENSOR_CO2_DECIMALS             0

#define SENSOR_UNKNOWN_TOPIC            "unknown"
#define SENSOR_TEMPERATURE_TOPIC        "temperature"
#define SENSOR_HUMIDITY_TOPIC           "humidity"
#define SENSOR_PRESSURE_TOPIC           "pressure"
#define SENSOR_CURRENT_TOPIC            "current"
#define SENSOR_VOLTAGE_TOPIC            "voltage"
#define SENSOR_ACTIVE_POWER_TOPIC       "power"
#define SENSOR_APPARENT_POWER_TOPIC     "apparent"
#define SENSOR_REACTIVE_POWER_TOPIC     "reactive"
#define SENSOR_POWER_FACTOR_TOPIC       "factor"
#define SENSOR_ENERGY_TOPIC             "energy"
#define SENSOR_ENERGY_DELTA_TOPIC       "energy_delta"
#define SENSOR_PM1dot0_TOPIC            "pm1dot0"
#define SENSOR_PM2dot5_TOPIC            "pm2dot5"
#define SENSOR_PM10_TOPIC               "pm10"
#define SENSOR_ANALOG_TOPIC             "analog"
#define SENSOR_DIGITAL_TOPIC            "digital"
#define SENSOR_EVENTS_TOPIC             "events"
#define SENSOR_CO2_TOPIC                "co2"

#define HUMIDITY_NORMAL                 0
#define HUMIDITY_COMFORTABLE            1
#define HUMIDITY_DRY                    2
#define HUMIDITY_WET                    3

//--------------------------------------------------------------------------------
// Analog sensor
// Enable support by passing ANALOG_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef ANALOG_SUPPORT
#define ANALOG_SUPPORT                  0
#endif

#ifndef ANALOG_PIN
#define ANALOG_PIN                      0
#endif

#ifndef ANALOG_PIN_MODE
#define ANALOG_PIN_MODE                 INPUT
#endif

#if ANALOG_SUPPORT
    #undef ADC_VCC_ENABLED
    #define ADC_VCC_ENABLED             0
#endif

//--------------------------------------------------------------------------------
// BME280/BMP280
// Enable support by passing BMX280_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef BMX280_SUPPORT
#define BMX280_SUPPORT                  0
#endif

#ifndef BMX280_ADDRESS
#define BMX280_ADDRESS                  0
#endif

#define BMX280_MODE                     1       // 1 for forced mode, 3 for normal mode
#define BMX280_TEMPERATURE              1       // Oversampling for temperature (set to 0 to disable magnitude)
#define BMX280_HUMIDITY                 1       // Oversampling for humidity (set to 0 to disable magnitude, only for BME280)
#define BMX280_PRESSURE                 1       // Oversampling for pressure (set to 0 to disable magnitude)

//--------------------------------------------------------------------------------
// Dallas OneWire temperature sensors
// Enable support by passing DALLAS_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT                  0
#endif

#ifndef DALLAS_PIN
#define DALLAS_PIN                      13
#endif

#ifndef DALLAS_PULLUP
#define DALLAS_PULLUP                   1
#endif

#define DALLAS_RESOLUTION               9        // Not used atm

//--------------------------------------------------------------------------------
// DHTXX temperature/humidity sensor
// Enable support by passing DHT_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef DHT_SUPPORT
#define DHT_SUPPORT                     0
#endif

#ifndef DHT_PIN
#define DHT_PIN                         13
#endif

#ifndef DHT_TYPE
#define DHT_TYPE                        DHT22
#endif

//--------------------------------------------------------------------------------
// Digital sensor
// Enable support by passing DIGITAL_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef DIGITAL_SUPPORT
#define DIGITAL_SUPPORT                 0
#endif

#ifndef DIGITAL_PIN
#define DIGITAL_PIN                     2
#endif

#ifndef DIGITAL_PIN_MODE
#define DIGITAL_PIN_MODE                INPUT_PULLUP
#endif

#ifndef DIGITAL_DEFAULT_STATE
#define DIGITAL_DEFAULT_STATE           1
#endif

//--------------------------------------------------------------------------------
// Energy Monitor general settings
//--------------------------------------------------------------------------------

#define EMON_MAX_SAMPLES                1000        // Max number of samples to get
#define EMON_MAX_TIME                   250         // Max time in ms to sample
#define EMON_FILTER_SPEED               512         // Mobile average filter speed
#define EMON_MAINS_VOLTAGE              230         // Mains voltage
#define EMON_REFERENCE_VOLTAGE          3.3         // Reference voltage of the ADC
#define EMON_CURRENT_RATIO              30          // Current ratio in the clamp (30V/1A)
#define EMON_REPORT_CURRENT             0           // Report current
#define EMON_REPORT_POWER               1           // Report power
#define EMON_REPORT_ENERGY              1           // Report energy

//--------------------------------------------------------------------------------
// Energy Monitor based on ADC121
// Enable support by passing EMON_ADC121_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef EMON_ADC121_SUPPORT
#define EMON_ADC121_SUPPORT             0       // Do not build support by default
#endif

#define EMON_ADC121_I2C_ADDRESS         0x50    // I2C address of the ADC121

//--------------------------------------------------------------------------------
// Energy Monitor based on ADS1X15
// Enable support by passing EMON_ADS1X15_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef EMON_ADS1X15_SUPPORT
#define EMON_ADS1X15_SUPPORT            0       // Do not build support by default
#endif

#define EMON_ADS1X15_I2C_ADDRESS        0x48    // I2C address of the ADS1115
#define EMON_ADS1X15_TYPE               ADS1X15_CHIP_ADS1115
#define EMON_ADS1X15_GAIN               ADS1X15_REG_CONFIG_PGA_4_096V
#define EMON_ADS1X15_MASK               0x0F    // A0=1 A1=2 A2=4 A4=8

//--------------------------------------------------------------------------------
// Energy Monitor based on interval analog GPIO
// Enable support by passing EMON_ANALOG_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef EMON_ANALOG_SUPPORT
#define EMON_ANALOG_SUPPORT             0       // Do not build support by default
#endif

#if EMON_ANALOG_SUPPORT
    #undef ADC_VCC_ENABLED
    #define ADC_VCC_ENABLED             0
#endif

//--------------------------------------------------------------------------------
// Counter sensor
// Enable support by passing EVENTS_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef EVENTS_SUPPORT
#define EVENTS_SUPPORT                  0       // Do not build with counter support by default
#endif

#ifndef EVENTS_PIN
#define EVENTS_PIN                      2       // GPIO to monitor
#endif

#ifndef EVENTS_PIN_MODE
#define EVENTS_PIN_MODE                 INPUT   // INPUT, INPUT_PULLUP
#endif

#ifndef EVENTS_INTERRUPT_MODE
#define EVENTS_INTERRUPT_MODE           RISING  // RISING, FALLING, BOTH
#endif

#define EVENTS_DEBOUNCE                 50      // Do not register events within less than 10 millis

//--------------------------------------------------------------------------------
// MHZ19 CO2 sensor
// Enable support by passing MHZ19_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef MHZ19_SUPPORT
#define MHZ19_SUPPORT                   0
#endif

#define MHZ19_RX_PIN                    13
#define MHZ19_TX_PIN                    15

//--------------------------------------------------------------------------------
// Particle Monitor based on Plantower PMSX003
// Enable support by passing PMSX003_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef PMSX003_SUPPORT
#define PMSX003_SUPPORT                 0
#endif

#define PMS_RX_PIN                      13
#define PMS_TX_PIN                      15

//--------------------------------------------------------------------------------
// SI7021 temperature & humidity sensor
// Enable support by passing SI7021_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef SI7021_SUPPORT
#define SI7021_SUPPORT                  1
#endif

#ifndef SI7021_ADDRESS
#define SI7021_ADDRESS                  0x40
#endif

//--------------------------------------------------------------------------------
// Internal power montior
// Enable support by passing ADC_VCC_ENABLED=1 build flag
// Do not enable this if using the analog GPIO for any other thing
//--------------------------------------------------------------------------------

#ifndef ADC_VCC_ENABLED
#define ADC_VCC_ENABLED             1
#endif

#if ADC_VCC_ENABLED
    ADC_MODE(ADC_VCC);#endif