diff --git a/code/html/index.html b/code/html/index.html index 7f119cd0..e81bdb22 100644 --- a/code/html/index.html +++ b/code/html/index.html @@ -530,7 +530,7 @@
- @@ -543,7 +543,7 @@
-
+
@@ -571,7 +571,7 @@
- @@ -583,7 +583,7 @@
- @@ -617,7 +617,7 @@
-
+
If enabled, add virtual relay switch that controls the ON / OFF state.
@@ -625,7 +625,7 @@
-
+
Save channel & brightness values in settings
@@ -633,7 +633,7 @@
-
+
When "Save values" is enabled, wait for the delay (ms) before the values are saved
@@ -641,7 +641,7 @@
-
+
Use the first three channels as RGB channels. This will also enable the color picker in the web UI. Will only work if the device has at least 3 dimmable channels.
Reload the page to update the web interface.
@@ -649,7 +649,7 @@
-
+
Use RGB color picker if enabled (plus brightness), otherwise use HSV (hue-saturation-value) style
@@ -657,7 +657,7 @@
-
+
For 2 channels warm white and cold white lights or color lights to use forth dimmable channel as (cold) white light calculated out of the RGB values.
Will only work if the device has at least 4 dimmable channels.
Enabling this will render useless the "Channel 4" slider in the status page.
Reload the page to update the web interface.
@@ -665,7 +665,7 @@
-
+
Use a dimmable channel as warm white light and another dimmable channel as cold white light.
On devices with two dimmable channels the first use used for warm white light and the second for cold white light.
On color lights the fifth use used for warm white light and the fourth for cold white light.
Will only work if the device has exactly 2 dimmable channels or at least 5 dimmable channels and "white channel" above is also ON.
Enabling this will render useless the "Channel 5" slider in the status page.
Reload the page to update the web interface.
@@ -673,7 +673,7 @@
-
+
Use gamma correction for RGB channels.
Will only work if "use colorpicker" above is also ON.
@@ -681,7 +681,7 @@
-
+
If enabled, channel changes will be smoothed.
@@ -689,7 +689,7 @@
-
+
Time to transition from one color to another (ms)
@@ -697,7 +697,7 @@
-
+
(ms, depends on the transition time)
@@ -705,7 +705,7 @@
-
+
Sync color between different lights.
@@ -751,7 +751,7 @@
- +
@@ -794,7 +794,7 @@
- +
@@ -829,7 +829,7 @@
The device has bytes available for OTA updates. If your image is larger than this consider doing a two-step update.
- +
@@ -858,7 +858,7 @@
-
+
@@ -936,7 +936,7 @@ Default topic
- +
Specific topics @@ -1008,22 +1008,22 @@
-
+
- +
- +
- +
@@ -1033,13 +1033,13 @@
- +
- +
@@ -1049,7 +1049,7 @@
- @@ -1058,22 +1058,22 @@
-
+
- +
-
+
- +
This is the fingerprint for the SSL certificate of the server.
@@ -1085,7 +1085,7 @@
- +
This is the root topic for this device. The {hostname} and {mac} placeholders will be replaced by the device hostname and MAC address.
@@ -1107,7 +1107,7 @@
-
+
@@ -1141,7 +1141,7 @@
- +
Address of the NoFUSS server
@@ -1175,12 +1175,12 @@
- +
- +
POSIX TZ variable, defaults to UTC0
For the list of possible options, see esp8266/Arduino's TZ.h (use the value inside of F("...")). For the complete documentation, see libc tzset(3) manual page
@@ -1204,7 +1204,7 @@
-
+
@@ -1237,12 +1237,12 @@
-
+
-
+
@@ -1256,12 +1256,12 @@
- +
- +
@@ -1282,7 +1282,7 @@
- +
@@ -1293,12 +1293,12 @@
- +
- +
@@ -1309,12 +1309,12 @@
- +
- +
@@ -1376,17 +1376,17 @@
-
+
- +
- +
Sensors & actuators @@ -1479,12 +1479,12 @@
-
+
-
+
@@ -1496,12 +1496,12 @@
- +
- +
Sensors & actuators @@ -1538,32 +1538,32 @@
-
+
- +
- +
- +
- +
- +
@@ -1591,7 +1591,7 @@
-
+
@@ -1603,7 +1603,7 @@
- +
Rules @@ -1648,7 +1648,7 @@ Type "debug" to display MCU serial exchanges. Any other command is sent to MCU serial as is.
- +
@@ -1729,7 +1729,7 @@
- @@ -1737,7 +1737,7 @@
- @@ -1745,7 +1745,7 @@
- @@ -1754,7 +1754,7 @@
-
+
Move this switch to ON and press "Save" to reset gas sensor calibration. Check the sensor datasheet for calibration conditions.
@@ -1764,42 +1764,42 @@
- +
Mains voltage in your system (in V).
- +
In Amperes (A). If you are using a pure resistive load like a bulb, this will be the ratio between the two previous values, i.e. power / voltage. You can also use a current clamp around one of the power wires to get this value.
- +
In Volts (V). Enter your the nominal AC voltage for your household or facility, or use multimeter to get this value.
- +
In Watts (W). Calibrate your sensor connecting a pure resistive load (like a bulb) and enter here its nominal power or use a multimeter.
- +
Energy ratio in pulses/kWh.
-
+
Move this switch to ON and press "Save" to revert to factory calibration values.
@@ -1807,7 +1807,7 @@
-
+
Move this switch to ON and press "Save" to set energy count to 0.
@@ -1846,7 +1846,7 @@
-
+
Number of times to repeat transmission
@@ -1977,30 +1977,30 @@
-
+
- + - +
Leave empty for DHCP negotiation
- +
Set when using a static IP
- +
Usually 255.255.255.0 for /24 networks
- +
Set the Domain Name Server IP to use when using a static IP
@@ -2032,7 +2032,7 @@
- +
 1 for Monday, 2 for Tuesday etc., comma separated
@@ -2147,7 +2147,7 @@
-
+
@@ -2155,7 +2155,7 @@
-
+
@@ -2164,7 +2164,7 @@
-
+
@@ -2172,7 +2172,7 @@
-
+
@@ -2244,9 +2244,9 @@
-
-
-
+
+
+
@@ -2254,15 +2254,15 @@
-
+
-
-
+
+