Added Wifi Stecker Shuko device (thanks to @Geitde)

code/espurna/config/arduino.h

@@ -61,6 +61,7 @@
 //#define ARILUX_AL_LC02
 //#define WEMOS_D1_TARPUNA_SHIELD
 //#define GIZWITS_WITTY_CLOUD
+//#define EUROMATE_WIFI_STECKER_SCHUKO
 
 //--------------------------------------------------------------------------------
 // Features (values below are non-default values)

code/espurna/config/hardware.h

@@ -1458,6 +1458,38 @@
     #define HLW8012_CF1_PIN     5
     #define HLW8012_CF_PIN      4
 
+// -----------------------------------------------------------------------------
+// Euromate (?) Wifi Stecker Shuko
+// https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko/p/2291706
+// Thanks to @Geitde
+// -----------------------------------------------------------------------------
+
+#elif defined(EUROMATE_WIFI_STECKER_SCHUKO)
+
+    // Info
+    #define MANUFACTURER        "EUROMATE"
+    #define DEVICE              "WIFI_STECKER_SCHUKO"
+
+    // Buttons
+    #define BUTTON1_PIN         14
+    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
+    #define BUTTON1_RELAY       1
+
+    // Relays
+    // #define RELAY1_PIN       12
+    // #define RELAY1_TYPE      RELAY_TYPE_LATCHED_INVERSE
+    // #define RELAY1_RESET_PIN 5
+
+    // Hack: drive GPIO12 low and use GPIO5 as normal relay pin:
+    #define RELAY1_PIN          5
+    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
+    #define LED2_PIN            12 /* DUMMY: exploit default off state for GPIO12=low */
+    #define LED2_PIN_INVERSE    0
+
+    // LEDs
+    #define LED1_PIN            4
+    #define LED1_PIN_INVERSE    0
+
 // -----------------------------------------------------------------------------
 // Generic 8CH
 // -----------------------------------------------------------------------------

code/espurna/migrate.ino

@@ -727,6 +727,18 @@ void migrate() {
             setSetting("chLogic", 2, 0);
             setSetting("relays", 1);
 
+        #elif defined(EUROMATE_WIFI_STECKER_SCHUKO)
+
+            setSetting("board", 55);
+            setSetting("ledGPIO", 0, 4);
+            setSetting("ledLogic", 0, 0);
+            setSetting("ledGPIO", 1, 12);
+            setSetting("ledLogic", 1, 0);
+            setSetting("btnGPIO", 0, 14);
+            setSetting("btnRelay", 0, 0);
+            setSetting("relayGPIO", 0, 5);
+            setSetting("relayType", 0, RELAY_TYPE_NORMAL);
+
         #else
 
             // Allow users to define new settings without migration config

code/platformio.ini

@@ -1471,6 +1471,30 @@ upload_port = "${env.ESPURNA_IP}"
 upload_flags = --auth=${env.ESPURNA_AUTH} --port 8266
 extra_scripts = ${common.extra_scripts}
 
+[env:euromate-wifi-stecker-shuko]
+platform = ${common.platform}
+framework = arduino
+board = esp01_1m
+board_flash_mode = dout
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = ${common.build_flags} -DEUROMATE_WIFI_STECKER_SCHUKO
+monitor_baud = 115200
+extra_scripts = ${common.extra_scripts}
+
+[env:euromate-wifi-stecker-shuko-ota]
+platform = ${common.platform}
+framework = arduino
+board = esp01_1m
+board_flash_mode = dout
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = ${common.build_flags} -DEUROMATE_WIFI_STECKER_SCHUKO
+upload_speed = 115200
+upload_port = "${env.ESPURNA_IP}"
+upload_flags = --auth=${env.ESPURNA_AUTH} --port 8266
+extra_scripts = ${common.extra_scripts}
+
 [env:stm-relay-ota]
 platform = ${common.platform}
 framework = arduino