Clean code

code/espurna/config/hardware.h

@@ -2747,6 +2747,25 @@
     #define ENCODER1_CHANNEL2   1   // please note this value is 0-based (LIGHT_CH2 above)
     #define ENCODER1_MODE       ENCODER_MODE_RATIO
 
+#elif defined(PHYX_ESP12_RGB)
+
+    // Info
+    #define MANUFACTURER        "PHYX"
+    #define DEVICE              "ESP12_RGB"
+    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
+    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
+    #define DUMMY_RELAY_COUNT   1
+
+    // Light
+    #define LIGHT_CHANNELS      3
+    #define LIGHT_CH1_PIN       4       // RED
+    #define LIGHT_CH2_PIN       14      // GREEN
+    #define LIGHT_CH3_PIN       12      // BLUE
+    #define LIGHT_CH1_INVERSE   0
+    #define LIGHT_CH2_INVERSE   0
+    #define LIGHT_CH3_INVERSE   0
+
+
 // -----------------------------------------------------------------------------
 // TEST boards (do not use!!)
 // -----------------------------------------------------------------------------
@@ -2927,24 +2946,6 @@
     #define LLMNR_SUPPORT       1
     #define NETBIOS_SUPPORT     1
     #define SSDP_SUPPORT        1
-    
-#elif defined(PHYX_ESP12_RGB)
-
-    // Info
-    #define MANUFACTURER        "PHYX"
-    #define DEVICE              "ESP12_RGB"
-    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
-    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
-    #define DUMMY_RELAY_COUNT   1
-
-    // Light
-    #define LIGHT_CHANNELS      3
-    #define LIGHT_CH1_PIN       4       // RED
-    #define LIGHT_CH2_PIN       14      // GREEN
-    #define LIGHT_CH3_PIN       12      // BLUE
-    #define LIGHT_CH1_INVERSE   0
-    #define LIGHT_CH2_INVERSE   0
-    #define LIGHT_CH3_INVERSE   0
 
 #endif
 

code/espurna/migrate.ino

@@ -1175,6 +1175,20 @@ void migrate() {
             setSetting("relayType", 0, RELAY_TYPE_NORMAL);
             setSetting("relayType", 1, RELAY_TYPE_NORMAL);
 
+        #elif defined(XIAOMI_SMART_DESK_LAMP)
+
+            setSetting("board", 89);
+
+            setSetting("relayProvider", RELAY_PROVIDER_LIGHT);
+            setSetting("lightProvider", LIGHT_PROVIDER_DIMMER);
+            setSetting("relays", 1);
+            setSetting("chGPIO", 0, 4);
+            setSetting("chGPIO", 1, 14);
+            setSetting("chGPIO", 2, 12);
+            setSetting("chLogic", 0, 0);
+            setSetting("chLogic", 1, 0);
+            setSetting("chLogic", 3, 0);
+
         #else
 
             // Allow users to define new settings without migration config

code/platformio.ini

@@ -2623,3 +2623,28 @@ upload_port = ${common.upload_port}
 upload_flags = ${common.upload_flags}
 monitor_speed = ${common.monitor_speed}
 extra_scripts = ${common.extra_scripts}
+
+[env:phyx-esp12-rgb]
+platform = ${common.platform}
+framework = ${common.framework}
+board = ${common.board_1m}
+board_build.flash_mode = ${common.flash_mode}
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = ${common.build_flags_1m0m} -DPHYX_ESP12_RGB
+monitor_speed = ${common.monitor_speed}
+extra_scripts = ${common.extra_scripts}
+
+[env:phyx-esp12-rgb-ota]
+platform = ${common.platform}
+framework = ${common.framework}
+board = ${common.board_1m}
+board_build.flash_mode = ${common.flash_mode}
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = ${common.build_flags_1m0m} -DPHYX_ESP12_RGB
+upload_speed = ${common.upload_speed}
+upload_port = ${common.upload_port}
+upload_flags = ${common.upload_flags}
+monitor_speed = ${common.monitor_speed}
+extra_scripts = ${common.extra_scripts}