Merged in mactijn/espurna/dev (pull request #28)

Add Huacanxing H802 support

Approved-by: Xose Pérez <xose.perez@gmail.com>

code/espurna/config/arduino.h

@@ -39,6 +39,7 @@
 //#define JANGOE_WIFI_RELAY_NO
 //#define JORGEGARCIA_WIFI_RELAYS
 //#define OPENENERGYMONITOR_MQTT_RELAY
+//#define HUACANXING_H802
 
 //--------------------------------------------------------------------------------
 // Features (values below are non-default values)

code/espurna/config/hardware.h

@@ -809,6 +809,30 @@
     #define RELAY1_TYPE         RELAY_TYPE_LATCHED
     #define RELAY1_RESET_PIN    12
 
+// -----------------------------------------------------------------------------
+// HUACANXING H802
+// -----------------------------------------------------------------------------
+
+#elif defined(HUACANXING_H802)
+
+    // Info
+    #define MANUFACTURER        "HUACANXING"
+    #define DEVICE              "H802"
+    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
+    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
+    #define DUMMY_RELAY_COUNT   1
+
+    // Channels
+    #define LIGHT_CH1_PIN       12      // RED
+    #define LIGHT_CH2_PIN       14      // GREEN
+    #define LIGHT_CH3_PIN       13      // BLUE
+    #define LIGHT_CH4_PIN       15      // WHITE
+
+    #define LIGHT_CH1_INVERSE   0
+    #define LIGHT_CH2_INVERSE   0
+    #define LIGHT_CH3_INVERSE   0
+    #define LIGHT_CH4_INVERSE   0
+
 // -----------------------------------------------------------------------------
 // Unknown hardware
 // -----------------------------------------------------------------------------

code/espurna/hardware.ino

@@ -419,6 +419,21 @@ void hwUpwardsCompatibility() {
         setSetting("relayResetGPIO", 1, 12);
         setSetting("relayType", 1, RELAY_TYPE_NORMAL);
 
+    #elif defined(HUACANXING_H802)
+
+        setSetting("board", 36);
+        setSetting("relayProvider", RELAY_PROVIDER_LIGHT);
+        setSetting("lightProvider", LIGHT_PROVIDER_DIMMER);
+        setSetting("chGPIO", 1, 12);
+        setSetting("chGPIO", 2, 14);
+        setSetting("chGPIO", 3, 13);
+        setSetting("chGPIO", 4, 15);
+        setSetting("chLogic", 1, 0);
+        setSetting("chLogic", 2, 0);
+        setSetting("chLogic", 3, 0);
+        setSetting("chLogic", 4, 0);
+        setSetting("relays", 1);
+
     #else
 
         #error "UNSUPPORTED HARDWARE!"

code/platformio.ini

@@ -831,3 +831,26 @@ build_flags = ${common.build_flags} -D${env.BOARD}
 upload_speed = 115200
 upload_port = "${env.IP}"
 upload_flags = --auth=${env.AUTH} --port 8266
+
+[env:huacanxing-h802]
+platform = espressif8266
+framework = arduino
+board = esp01_1m
+board_flash_mode = dout
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = -g -Wl,-Tesp8266.flash.1m0.ld -DHUACANXING_H802 -DDEBUG_PORT=Serial1
+monitor_baud = 115200
+
+[env:huacanxing-h802-ota]
+platform = espressif8266
+framework = arduino
+board = esp01_1m
+board_flash_mode = dout
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = -g -Wl,-Tesp8266.flash.1m0.ld -DHUACANXING_H802 -DDEBUG_PORT=Serial1
+upload_speed = 115200
+upload_port = "192.168.4.1"
+upload_flags = --auth=fibonacci --port 8266
+monitor_baud = 115200