hardware: Add support for Aoycocr X5P Plug. (#2235)

* hardware: Add support for Aoycocr X5P Plug.

This change allow espurna to control Aoycocr X5P Plug devices, which has
the same behaviour as the GOSUND WP3 but using different GPIO pins for
relay, button and leds.

* Update platformio.ini

Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>

code/espurna/config/arduino.h

@@ -15,6 +15,7 @@
 //#define ALLTERCO_SHELLY1PM
 //#define ALLTERCO_SHELLY2
 //#define ALLTERCO_SHELLY25
+//#define AOYCOCR_X5P
 //#define ARILUX_AL_LC01
 //#define ARILUX_AL_LC02
 //#define ARILUX_AL_LC02_V14

code/espurna/config/hardware.h

@@ -3281,7 +3281,7 @@
 
 // -----------------------------------------------------------------------------
 // The Gosund WP3 is based on ESP8285, so 1 MB internal flash (DOUT required)
-// The module has no-connect:  TX, RX, RST, AD, GPIO5, (and GPIO0, 
+// The module has no-connect:  TX, RX, RST, AD, GPIO5, (and GPIO0,
 //     GPIO2 via test points on the back of the module)
 // and these are wired to devices:
 // GPIO4: /BTN
@@ -3618,6 +3618,45 @@
     #define I2C_SDA_PIN         12
     #define I2C_SCL_PIN         14
 
+// -----------------------------------------------------------------------------
+// This device has teh same behaviour as the GOSUND WP3, but with different GPIO pin values
+// GPIO equivalents extracted from https://templates.blakadder.com/aoycocr_X5P.html
+
+#elif defined(AOYCOCR_X5P)
+
+    // Info
+    #define MANUFACTURER                "AOYCOCR"
+    #define DEVICE                      "X5P"
+
+    // Buttons
+    #define BUTTON1_PIN                 13
+    #define BUTTON1_CONFIG              BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
+    #define BUTTON1_RELAY               1
+    // the defaults are reasonable, but you can change them as desired
+    //#define BUTTON1_PRESS               BUTTON_ACTION_NONE
+    //#define BUTTON1_CLICK               BUTTON_ACTION_TOGGLE
+    //#define BUTTON1_DBLCLICK            BUTTON_ACTION_AP
+    //#define BUTTON1_LNGCLICK            BUTTON_ACTION_RESET
+    //#define BUTTON1_LNGLNGCLICK         BUTTON_ACTION_FACTORY
+
+    // Relays
+    #define RELAY1_PIN                  15
+    #define RELAY1_TYPE                 RELAY_TYPE_NORMAL
+
+    // LEDs
+
+    // LED1 (red) indicates on/off state; you could use LED_MODE_FOLLOW_INVERSE
+    // so that the LED lights the button when 'off' so it can be found easily.
+    #define LED1_PIN                    0
+    #define LED1_PIN_INVERSE            1
+    #define LED1_MODE                   LED_MODE_FOLLOW
+    #define LED1_RELAY                  1
+
+    // LED2 (blue) indicates wifi activity
+    #define LED2_PIN                    2
+    #define LED2_PIN_INVERSE            1
+    #define LED2_MODE                   LED_MODE_WIFI
+
 // -----------------------------------------------------------------------------
 
 // also works with https://www.amazon.com/gp/product/B07TMY394G/

code/platformio.ini

@@ -998,3 +998,7 @@ src_build_flags = -DEHOMEDIY_WT02
 [env:ehomediy-wt03]
 extends = env:esp8266-1m-base
 src_build_flags = -DEHOMEDIY_WT03
+
+[env:aoycocr-x5p]
+extends = env:esp8266-1m-base
+src_build_flags = -DAOYCOCR_X5P