add new "magichome-led-controller-ir" with changed GPIO order

code/espurna/config/arduino.h

@@ -34,6 +34,7 @@
 //#define WORKCHOICE_ECOPLUG
 //#define AITHINKER_AI_LIGHT
 //#define MAGICHOME_LED_CONTROLLER
+//#define MAGICHOME_LED_CONTROLLER_IR
 //#define HUACANXING_H801
 //#define JANGOE_WIFI_RELAY_NC
 //#define JANGOE_WIFI_RELAY_NO

code/espurna/config/hardware.h

@@ -647,6 +647,35 @@
     #define LIGHT_CH3_INVERSE   0
     #define LIGHT_CH4_INVERSE   0
 
+// -----------------------------------------------------------------------------
+// LED Controller With IR
+// -----------------------------------------------------------------------------
+
+#elif defined(MAGICHOME_LED_CONTROLLER_IR)
+
+    // Info
+    #define MANUFACTURER        "MAGICHOME"
+    #define DEVICE              "LED_CONTROLLER_IR"
+    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
+    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
+    #define DUMMY_RELAY_COUNT   1
+
+    // LEDs
+    #define LED1_PIN            2
+    #define LED1_PIN_INVERSE    1
+
+    // Channels
+    #define LIGHT_CH1_PIN       5     // RED
+    #define LIGHT_CH2_PIN       12    // GREEN
+    #define LIGHT_CH3_PIN       13    // BLUE
+    //#define LIGHT_CH4_PIN     13    // WHITE
+    #define LIGHT_IR_PIN        14    // IR LED ?
+
+    #define LIGHT_CH1_INVERSE   0
+    #define LIGHT_CH2_INVERSE   0
+    #define LIGHT_CH3_INVERSE   0
+    #define LIGHT_CH4_INVERSE   0
+
 // -----------------------------------------------------------------------------
 // HUACANXING H801
 // -----------------------------------------------------------------------------

code/espurna/hardware.ino

@@ -242,6 +242,23 @@ void hwUpwardsCompatibility() {
         setSetting("chLogic", 4, 0);
         setSetting("relays", 1);
 
+    #elif defined(MAGICHOME_LED_CONTROLLER_IR)
+
+        setSetting("board", 21);
+        setSetting("relayProvider", RELAY_PROVIDER_LIGHT);
+        setSetting("lightProvider", LIGHT_PROVIDER_DIMMER);
+        setSetting("ledGPIO", 1, 2);
+        setSetting("ledLogic", 1, 1);
+        setSetting("chGPIO", 1, 5);
+        setSetting("chGPIO", 2, 12);
+        setSetting("chGPIO", 3, 13);
+        setSetting("chGPIO", 4, 14);
+        setSetting("chLogic", 1, 0);
+        setSetting("chLogic", 2, 0);
+        setSetting("chLogic", 3, 0);
+        setSetting("chLogic", 4, 0);
+        setSetting("relays", 1);
+
     #elif defined(ITEAD_MOTOR)
 
         setSetting("board", 22);

code/platformio.ini

@@ -703,6 +703,29 @@ upload_port = "192.168.4.1"
 upload_flags = --auth=fibonacci --port 8266
 monitor_baud = 115200
 
+[env:magichome-led-controller-ir]
+platform = espressif8266
+framework = arduino
+board = esp01_1m
+board_flash_mode = dout
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = ${common.build_flags_1m} -DMAGICHOME_LED_CONTROLLER_IR
+monitor_baud = 115200
+
+[env:magichome-led-controller-ir-ota]
+platform = espressif8266
+framework = arduino
+board = esp01_1m
+board_flash_mode = dout
+lib_deps = ${common.lib_deps}
+lib_ignore = ${common.lib_ignore}
+build_flags = ${common.build_flags_1m} -DMAGICHOME_LED_CONTROLLER_IR
+upload_speed = 115200
+upload_port = "192.168.4.1"
+upload_flags = --auth=fibonacci --port 8266
+monitor_baud = 115200
+
 [env:huacanxing-h801]
 platform = espressif8266
 framework = arduino