- allow strings in mode (off, on, none)
- fixup type used for the mode to be am enum instead of int
(todo: allow webui to accept strings?)
- some cli updates using new funcs
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
- Add ::Released button event to be used specifically with switches, opposite of ::Pressed
- Always use default state for switches instead of ignoring it and using current pin reading as value. This allows us to boot with the switch held in the opposite state and trigger the correct event immediately
(meaning, switches now depend on the BUTTON_DEFAULT_HIGH presence to detect the default position)
- BREAKING: Fixup hardware.h. Any custom board needs manual changes.
- BREAKING: Rework MQTT button messages to send text from debug messages instead of numeric code
- Buttons events source as button property instead of a global one
- Rename events source -> provider for all settings, consistent with the other things like relay and light providers
- AnalogPin to read between a certain analogRead() range
Trying to follow defaults here - analog 'press' is digital LOW, default value is HIGH, so no additional cfg entries are needed besides pin, level and changing evt source
- (debug) Refactor gpio command, add adc to show analogRead(pin)
- (debug) Add button command
Implemented based on:
https://gitter.im/tinkerman-cat/espurna?at=5f5d44c8df4af236f902e25dhttps://gitter.im/tinkerman-cat/espurna?at=5f60e7f1f969413294e95370
- add ltDimmerGPIO<index> & ltDimmerInv<index> to override / add to hardware configuration. Add pin defaults, mapped as GPIO_NONE. pwm_init() receives resulting GPIO mapping based on settings loader.
- remove bogus _light_channels variable, use this name for channel array instead (...which is vector and has size(). functions always use that value anyway)
- use similar to relay & wifi, configuration through helper methods that
use indexed defines
- clock cycles for led delay polling
- button mode defaults
* relay: respect relay delay time when using NONE_OR_ONE sync
* fixup! relay: respect relay delay time when using NONE_OR_ONE sync
* calculate delay from flood window + existing delay
* configure flood max changes too
* oops, s -> ms
* count other way around
* interpret delay differently with sync_one/none_or_one
* instead of accumulation, ensure that max delay time is selected (if it is there at all)
* global interlock delay setting, allow to set change_delay before relayStatus(id, status) changes it
* fixup! global interlock delay setting, allow to set change_delay before relayStatus(id, status) changes it
* (finally) use lock attr to avoid user changing state while target != current state
* fix building with 2.3.0
* postpone wspost after all relays are processed, remove change_start refresh, snapshot relaySync value in configure
* fix warning
* add another timer for ONE
* travis: move build flags tests outside of hardware header
* mqtt: fix typo
* travis: use files instead of bundling test cases into script
* fixup! travis: use files instead of bundling test cases into script
* fix variable expansion, remove custom h at the end
* add ade7953 to sensors list
* custom.h path as variable
* shellcheck
* fix printf syntax, silent again
* fix bash 4.3 treating empty array as unset variable
Maxim Prokhorov
Pavel S
Xose Pérez
Lazar Obradovic