- shrink utils source file, move heartbeat and boot management into system
- improvise with 'heartbeat' functionality. include scheduler implementation that will
manage the per-module heartbeat callbacks with individual 'mode' and
'interval' settings. current ones are mqtt (including relays, lights, thermostat), debug and
influxdb. preserve heartbeat NONE, ONCE and REPEAT, REPEAT_STATUS is effectively a hbReport & status bit.
- mqtt heartbeat is managed through mqttHeartbeat() callbacks
- tweak mqtt callbacks to use lists instead of the vector, slighly reducing the size of the .bin
- update WebUI, include report setting and update hbMode values
- make sure general.h settings include new heartbeat,
move constant definitions outside of the header
- correctly include dependencies through the .cpp, avoid leaking
internal details.
- as a side-effect, base headers are no longer included recursively
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
- introduce zero threshold setting to reset value to 0 below a certain point (resolve#2264)
for example, set pwrPZeroThreshold0 10.0 for active power (or pwrQ... for apparent, pwrModS... for reactive) will reset always reset value to 0, similar to what turned off relay does. Default value is nan, since we can't use 0.0 on account of negative values.
- fix energy magnitude indexes usage, properly reset in API
- simplify sending pwr and emon Visible flags
- allow to use settings prefixes more, remove snsMinDelta & snsMaxDelta and use relative magnitude indexes
* wip based on early draft. todo benchmarking
* fixup eraser, assume keys are unique
* fix cursor copy, test removal at random
* small benchmark via permutations. todo lambdas and novirtual
* fix empty condition / reset
* overwrite optimizations, fix move offsets overflows
* ...erase using 0xff instead of 0
* test the theory with code, different length kv were bugged
* try to check for out-of-bounds writes / reads
* style
* trying to fix mover again
* clarify length, defend against reading len on edge
* fix uncommited rewind change
* prove space assumptions
* more concise traces, fix move condition (agrh!!!)
* slightly more internal knowledge (estimates API?)
* make sure cursor is only valid within the range
* ensure 0 does not blow things
* go back up
* cursor comments
* comments
* rewrite writes through cursor
* in del too
* estimate kv storage requirements, return available size
* move raw erase / move into a method, allow ::set to avoid scanning storage twice
* refactor naming, use in code
* amend storage slicing test
* fix crash handler offsets, cleanup configuration
* start -> begin
* eeprom readiness
* dependencies
* unused
* SPI_FLASH constants for older Core
* vtables -> templates
* less include dependencies
* gcov help, move estimate outside of the class
* writer position can never match, use begin + offset
* tweak save_crash to trigger only once in a serious crash
* doh, header function should be inline
* foreach api, tweak structs for public api
* use test helper class
* when not using foreach, move cursor reset closer to the loop using read_kv
* coverage comments, fix typo in tests decltype
* ensure set() does not break with offset
* make codacy happy again
Change the underlying command line handling:
- switch to a custom parser, inspired by redis / sds
- update terminalRegisterCommand signature, pass only bare minimum
- clean-up `help` & `commands`. update settings `set`, `get` and `del`
- allow our custom test suite to run command-line tests
- clean-up Stream IO to allow us to print large things into debug stream (for example, `eeprom.dump`)
- send parsing errors to the debug log
As a proof of concept, introduce `TERMINAL_MQTT_SUPPORT` and `TERMINAL_WEB_API_SUPPORT`
- MQTT subscribes to the `<root>/cmd/set` and sends response to the `<root>/cmd`. We can't output too much, as we don't have any large-send API.
- Web API listens to the `/api/cmd?apikey=...&line=...` (or PUT, params inside the body). This one is intended as a possible replacement of the `API_SUPPORT`. Internals introduce a 'task' around the AsyncWebServerRequest object that will simulate what WiFiClient does and push data into it continuously, switching between CONT and SYS.
Both are experimental. We only accept a single command and not every command is updated to use Print `ctx.output` object. We are also somewhat limited by the Print / Stream overall, perhaps I am overestimating the usefulness of Arduino compatibility to such an extent :)
Web API handler can also sometimes show only part of the result, whenever the command tries to yield() by itself waiting for something. Perhaps we would need to create a custom request handler for that specific use-case.
* broker: declare and define per module
We no longer need to specify each Broker type in broker.h
But, we exchange that bit for explicit initialization of the instance
Define helper macros to generate boilerplate code
- namespace with Instance, Register(), Publish()
- forward Register(...) -> Instance.Register(...),
Publish(...) -> Instance.Publish(...)
* don't check for broker when deps enable it
* emon: configure ratios without reboot
* settings: serialize() support
* debug: use vsnprintf from newlib, not from sdk
* settings/experimental: show defaults via `get`
* emon: override base methods, fix defaults
* sensor/emon: expose internal index calculation
- refactor configuration to use the correct index when accessing indexed
sensor methods. store index value on magnitude, refactor loops to
accomodate this new functionality
- rename slot(index) -> description(index), since we use 'slot' as
numeric value
- general conversion from .ino modules into a separate .cpp files
- clean-up internal headers, place libraries into .h. guard .cpp with _SUPPORT flags
- fix some instances of shared variables instead of public methods
- tweak build system to still build a single source file via os environment variable ESPURNA_BUILD_SINGLE_SOURCE
Maxim Prokhorov
Xose Pérez