- make sure we have custom provider before calling the update,
replace old check in the update function
- fix race condition in the provider function, causing complete lock-up of
lights controls (triggered by sending light updates very fast. for example,
using arrow keys with the webui sliders; ref. #2424)
- rework state change functions to work using loop() func instead of a
pair of scheduled functions. we should not go out-of-sync now, and it
also avoids forcibly creating std::func object each invocation
- rework other providers to be more in line with custom callbacks -
introduce state, value and update calls as a common way to handle lights
- correctly handle state change when turning OFF and ON
- update tuya to store the last state, never send channel values when OFF (ref. #2424)
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
Change the underlying command line handling:
- switch to a custom parser, inspired by redis / sds
- update terminalRegisterCommand signature, pass only bare minimum
- clean-up `help` & `commands`. update settings `set`, `get` and `del`
- allow our custom test suite to run command-line tests
- clean-up Stream IO to allow us to print large things into debug stream (for example, `eeprom.dump`)
- send parsing errors to the debug log
As a proof of concept, introduce `TERMINAL_MQTT_SUPPORT` and `TERMINAL_WEB_API_SUPPORT`
- MQTT subscribes to the `<root>/cmd/set` and sends response to the `<root>/cmd`. We can't output too much, as we don't have any large-send API.
- Web API listens to the `/api/cmd?apikey=...&line=...` (or PUT, params inside the body). This one is intended as a possible replacement of the `API_SUPPORT`. Internals introduce a 'task' around the AsyncWebServerRequest object that will simulate what WiFiClient does and push data into it continuously, switching between CONT and SYS.
Both are experimental. We only accept a single command and not every command is updated to use Print `ctx.output` object. We are also somewhat limited by the Print / Stream overall, perhaps I am overestimating the usefulness of Arduino compatibility to such an extent :)
Web API handler can also sometimes show only part of the result, whenever the command tries to yield() by itself waiting for something. Perhaps we would need to create a custom request handler for that specific use-case.
* broker: declare and define per module
We no longer need to specify each Broker type in broker.h
But, we exchange that bit for explicit initialization of the instance
Define helper macros to generate boilerplate code
- namespace with Instance, Register(), Publish()
- forward Register(...) -> Instance.Register(...),
Publish(...) -> Instance.Publish(...)
* don't check for broker when deps enable it
- general conversion from .ino modules into a separate .cpp files
- clean-up internal headers, place libraries into .h. guard .cpp with _SUPPORT flags
- fix some instances of shared variables instead of public methods
- tweak build system to still build a single source file via os environment variable ESPURNA_BUILD_SINGLE_SOURCE
- mask is defined as (relay# status << number)
- transparently handle base-2 and base-10 numbers
- if the relay mode requires us to save the mask, it will be saved as base-2
- add experimental `relayDummy` to configure dummy relays at runtime
- add tuya-generic-dimmer #1729
- cleanup broker interface to allow Tuya module to properly receive events, modify broker methods to allow different function signatures
- add basic tests for Tuya frame and data protocol
Maxim Prokhorov