- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
* Completed kingart curtain switch support:
Added Web UI controls and view in status
Added power up behaviour (nothing, close, open, last position)
Added curtain style (Roller, etc...) for UI status and to be used in MQTT
* Checked commit before PR. Added html gulp static files generated.
* Corrected a code refactor error which make the MQTT messages not handling position from received messages. Added comment to debug tab to show how to enable debug
* Use the maximum compression for gzip. A byte is a byte :)
* Update code/espurna/curtain_kingart.cpp
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
* Variable name prefix update
Added public set position function and curtain count
* Added Scheduler new type : curtain
* Add curtain schedule support and correct the 12h bug when adding a slot (00:00 after refresh). Default Hour is 12h
* Code cleaning.
Schedule support.
Light support is having an issue with new schedules corrected here.
* I let do better by the specialists
* Curtain init statues
* Coding style corrections
* Removed debug stuff from now - will be back later with the right way
* rebuild webui
* revert 435f1c5e03 schHour default, rebuild ui
Co-authored-by: Eric Chauvet <eric.chauvet@test-tree.com>
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
- general conversion from .ino modules into a separate .cpp files
- clean-up internal headers, place libraries into .h. guard .cpp with _SUPPORT flags
- fix some instances of shared variables instead of public methods
- tweak build system to still build a single source file via os environment variable ESPURNA_BUILD_SINGLE_SOURCE
* ntp: try using sntp app from lwip, drop ntpclientlib
* fix display
* thermostat: fix day and month getters
* test build sizes with scheduler
* use system timers for once-a-minute scheduling, no polling
* tick
* avoid timestamps, use tm
* drop utc rpn operator, add utc_hour and utc_dow
* try to build with old implementation too
* dep
* notify ws
* progmem
* cleanup types
* offset tm values by 1 to match existing schedules
* avoid using ntpclientlib with rpn
* test. show debug strings in sch
* fix secureclient
* consts, fix unsyncing when changing tz (and not triggering sntp after reinit for some reason)
* startup time in seconds
* same delay as lwip
* header
* assume build timestamp is unixtime
* cache server value
* fmt
* typo
* handle dhcp request
* rename
* web
* TZ.h
* add notice about what alias means
* fix disabling NTP_SUPPORT
* scheduled ticker
* same behaviour as old module
* rollback rpn dependency check, utc_ prefixes
* ...
* comments, refactor naming
- use setOriginalsFromValues function right after elements had changed and
**only** with those elements
- add checkbox handling to setOriginalsFromValues to match hasChanged
- apply hasChanged after value is set to refresh originals after saving
- change parts that already set 'original' attribute manually
This was sort-of broken, because original attr never worked as intended.
Also fix possible OOM for large WebUI images, since sending full config each time means that we need more memory to buffer and parse it.
- mask is defined as (relay# status << number)
- transparently handle base-2 and base-10 numbers
- if the relay mode requires us to save the mask, it will be saved as base-2
* relay: respect relay delay time when using NONE_OR_ONE sync
* fixup! relay: respect relay delay time when using NONE_OR_ONE sync
* calculate delay from flood window + existing delay
* configure flood max changes too
* oops, s -> ms
* count other way around
* interpret delay differently with sync_one/none_or_one
* instead of accumulation, ensure that max delay time is selected (if it is there at all)
* global interlock delay setting, allow to set change_delay before relayStatus(id, status) changes it
* fixup! global interlock delay setting, allow to set change_delay before relayStatus(id, status) changes it
* (finally) use lock attr to avoid user changing state while target != current state
* fix building with 2.3.0
* postpone wspost after all relays are processed, remove change_start refresh, snapshot relaySync value in configure
* fix warning
* add another timer for ONE
* Added restore last schedule support
* Merged RestoreLastScheduleState function into the _schCheck function
* handle lights in restore action
* hide webui chbox when not using scheduler
* use settings instead of struct member, hide under ifdef scheduler_support
* relayLastSchedule uses SCHEDULER_RESTORE_LAST_SCHEDULE as default
* Changed all the variable names to be the same so there would be no confusions
* Fixed client side to create an array from relayLastschedule
* Fixed cosmetic issue with the toggle display in webui
* Fixed variable name and disabled comparison at the end
* Added another check if the switch type is light provider
* Changed variables naming
* Naming mistake
- update every dynamicjsonbuffer with fixed size constructor argument
- change to ws callback registration to use a class builder (just cosmetic)
- test multiple ws data callbacks for each module
- remove some of the static strings in favour of ws data callback
- improve sensor ws callback data size, remove duplicated strings
- use static buffer in wsDebugSend
- postpone wsSend until loop, implement wsPost to allow other modules to queue message callbacks. remove Ticker based ws callbacks for data
- update WebUI files
* send all ws config at once on start
* reduce ws json overhead by creating message buffer manually
* use k:[values] instead of k1:value1, k2:value2 etc. for lists
Max Prokhorov
Eric Chauvet
foxman69
Xose Pérez
wysiwyng
wysiwyng