- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
- Buttons events source as button property instead of a global one
- Rename events source -> provider for all settings, consistent with the other things like relay and light providers
- AnalogPin to read between a certain analogRead() range
Trying to follow defaults here - analog 'press' is digital LOW, default value is HIGH, so no additional cfg entries are needed besides pin, level and changing evt source
- (debug) Refactor gpio command, add adc to show analogRead(pin)
- (debug) Add button command
Implemented based on:
https://gitter.im/tinkerman-cat/espurna?at=5f5d44c8df4af236f902e25dhttps://gitter.im/tinkerman-cat/espurna?at=5f60e7f1f969413294e95370
- (experimental) provide generic way to read magnitude values
- expose /api/metrics with values formatted specifically for prometheus, with relay and sensor data
- small tweaks to sensor init
Example config:
```
scrape_configs:
- job_name: 'espurna'
metrics_path: '/api/metrics'
params:
apikey: ['apikeyapikey']
static_configs:
- targets: ['espurna-blabla.lan:80']
```
Where ESPurna side has
```
apiKey => "apikeyapikey"
apiEnabled => "1"
```
Add support for BME680 using libalgobsec proprietary algorithms for precise Indoor Air Quality (IAQ) measurement. Unlike traditional CO2 sensors - and good ones are expensive - it measures nearly all VOCs compounds in the air (plus other gases) and compensates those measurements with its built-in temperature and humidity sensors to determine indoor air quality.
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
Change the underlying command line handling:
- switch to a custom parser, inspired by redis / sds
- update terminalRegisterCommand signature, pass only bare minimum
- clean-up `help` & `commands`. update settings `set`, `get` and `del`
- allow our custom test suite to run command-line tests
- clean-up Stream IO to allow us to print large things into debug stream (for example, `eeprom.dump`)
- send parsing errors to the debug log
As a proof of concept, introduce `TERMINAL_MQTT_SUPPORT` and `TERMINAL_WEB_API_SUPPORT`
- MQTT subscribes to the `<root>/cmd/set` and sends response to the `<root>/cmd`. We can't output too much, as we don't have any large-send API.
- Web API listens to the `/api/cmd?apikey=...&line=...` (or PUT, params inside the body). This one is intended as a possible replacement of the `API_SUPPORT`. Internals introduce a 'task' around the AsyncWebServerRequest object that will simulate what WiFiClient does and push data into it continuously, switching between CONT and SYS.
Both are experimental. We only accept a single command and not every command is updated to use Print `ctx.output` object. We are also somewhat limited by the Print / Stream overall, perhaps I am overestimating the usefulness of Arduino compatibility to such an extent :)
Web API handler can also sometimes show only part of the result, whenever the command tries to yield() by itself waiting for something. Perhaps we would need to create a custom request handler for that specific use-case.
* Fixes and updates for thermostat and display:
- Switch to original esp8266-oled-ssd1306 library
- Fixes and updates for thermostat and display
- Add display switching off after interval
- If THERMOSTAT_DISPLAY_SUPPORT enabled, then one click enable display, long click switch relay. This functionality also depend on fix for long click. See pull request https://github.com/xoseperez/espurna/pull/2172
* Move buttons definitions for display to dependencies.h
* Pin ThingPulse/esp8266-oled-ssd1306#3398c97
* ntp: try using sntp app from lwip, drop ntpclientlib
* fix display
* thermostat: fix day and month getters
* test build sizes with scheduler
* use system timers for once-a-minute scheduling, no polling
* tick
* avoid timestamps, use tm
* drop utc rpn operator, add utc_hour and utc_dow
* try to build with old implementation too
* dep
* notify ws
* progmem
* cleanup types
* offset tm values by 1 to match existing schedules
* avoid using ntpclientlib with rpn
* test. show debug strings in sch
* fix secureclient
* consts, fix unsyncing when changing tz (and not triggering sntp after reinit for some reason)
* startup time in seconds
* same delay as lwip
* header
* assume build timestamp is unixtime
* cache server value
* fmt
* typo
* handle dhcp request
* rename
* web
* TZ.h
* add notice about what alias means
* fix disabling NTP_SUPPORT
* scheduled ticker
* same behaviour as old module
* rollback rpn dependency check, utc_ prefixes
* ...
* comments, refactor naming
* Sensors: refactor configuration
- move sensor implementaion to the .ino,
remove dependency undef / define from sensor files
- update test/build/sensor.h from SENSOR_SUPPORT
- allow to change sensor config variables externally
- `#include <...>` for global headers and libraries,
fix relative path for math library
* add missing sns <-> i2c dependency
* ledrelay should return relay_none as default
* rollback to original test header
* include debug header when requested (relative)
* debug: store boot log
* order
* roll single header
* hide when not implemented
* fix capacity check
* dependencies
* refactor names, can just use malloc
* settings formatting
* dbgBuf prefix
* show size
* release memory after buffer is displayed
* fix uptime unused warning, combine printer
* comments
* use arg flag instead of static to handle boot
* ci test fix
* Hide whole info() without debug
* typo
* cleanup setDebugOutput condition
* web: revert changed from secure_client patch
* ota/httpupdate: use SecureClient
* ota/httpupdate: use scheduled function on mqtt event
* config: finish up 590282e changes + add warnings
* typo fix
* use bind instead of c++14 magic, use debug text from secureclient
* bump
* actually use the locking
* scripts: memanalyzer fixes
- cleanup duplication
- cleanup external dependencies
- properly use subprocess when calling pio, add debug mode
- cleanup argparse usage, use store_true actions instead of counters
- use python3 syntax and python3 shebang by default
- fix some issues with module dependencies
* move to scripts
* use simple return
* quick fix for rfm
* codacy unused import
* formatting
* show defaults
* while at it, rewrite to make pylint happy
* fix unused
* add windows support + note
- add experimental `relayDummy` to configure dummy relays at runtime
- add tuya-generic-dimmer #1729
- cleanup broker interface to allow Tuya module to properly receive events, modify broker methods to allow different function signatures
- add basic tests for Tuya frame and data protocol
* Use generic typechecks, OTA add followRedirects
* revamp using is_detected
* relative include
* mention ts draft instead, fix c++17 includes (still not buildable)
* typo
* Always create WiFiClient pointer
* Remove old CREATE_CHECK macro
* do not create wificlient obj when running old Core
* travis: move build flags tests outside of hardware header
* mqtt: fix typo
* travis: use files instead of bundling test cases into script
* fixup! travis: use files instead of bundling test cases into script
* fix variable expansion, remove custom h at the end
* add ade7953 to sensors list
* custom.h path as variable
* shellcheck
* fix printf syntax, silent again
* fix bash 4.3 treating empty array as unset variable
* telnet: buffered output for async server
* telnet: make async buffer an option
* just use the queue containers directly
* try with simpler list
* exhaust buffers as much as possible in a single try
* don't forget to destroy the client object
* naming
* kill the connection earlier
* fix merge issues
* MQTT rewrite with SSL fixes
- Added Arduino MQTT library support (actively maintained)
- Added support for BearSSL (core >= 2.5)
- BearSSL validation: insecure, fingerprinting and CA validation
- AxTLS validation: insecure and fingerprinting
- Support MFLN in order to reduce heap usage
* Better header incl, fix building w/ no NTP_SUPPORT
* Clean up code, use DEBUG_MSG_P
* Fix compile error
- add httpupdate ota impelementation
- move async ota into a separate module
- support bearssl & axtls through wificlientsecure
- allow to disable arduino ide ota module
Maxim Prokhorov
Rui Marinho
DmitryBlinov
foxman69
Niek van der Maas
Xose Pérez
Lazar Obradovic