Wrong credentials

SECURITY

Before using this device you have to change the default password for the user 'admin'. This password will be used for the AP mode hotspot, the web interface (where you are now) and the over-the-air updates.

 
The administrator password is used to access this web interface (user 'admin'), but also to connect to the device when in AP mode or to flash a new firmware over-the-air (OTA).
It should have at least eight characters (letters, numbers or the underscore) and at least one number, one lowercase and one uppercase letter.

STATUS

Current configuration

Manufacturer
Device
Chip ID
MAC
Network
IP
ESPurna Version
ESPurna Build
MQTT Status
NTP Status

GENERAL

General configuration values

 
This name will identify this device in your network (http://<hostname>.local). For this setting to take effect you should restart the wifi interface clicking the "Reconnect" button.
 
Here you can define what will be the status of the switch after a reboot.
 
Define how the different switches should be synchronized.
 
When pulse mode is enabled the switch will automatically switch back to its normal state after the pulse time (below).
 
Pulse time in seconds (maximum value is 60s, accepts decimals).
 
Delay in milliseconds to detect a double click (from 0 to 1000ms).
The lower this number the faster the device will respond to button clicks but the harder it will be to get a double click. Increase this number if you are having trouble to double click the button. Set this value to 0 to disable double click. You won't be able to set the device in AP mode manually but your device will respond immediately to button clicks.
You will have to reset the device after updating for this setting to apply.
 
 
Use color picker for the first 3 channels as RGB.
Will only work if the device has at least 3 dimmable channels.
Reload the page to update the web interface.
 
 
Use forth dimmable channel as white when first 3 have the same RGB value.
Will only work if the device has at least 4 dimmable channels.
Reload the page to update the web interface.
 
 
Use gamma correction for RGB channels.
Will only work if "use colorpicker" above is also ON.
Celsius (ºC)
Fahrenheit (ºF)

ADMINISTRATION

Device administration and security settings

 
The administrator password is used to access this web interface (user 'admin'), but also to connect to the device when in AP mode or to flash a new firmware over-the-air (OTA).
It should have at least eight characters (letters, numbers or the underscore) and at least one number, one lowercase and one uppercase letter.
 
This is the port for the web interface and API requests.
If different than 80 (standard HTTP port) you will have to add it explicitly to your requests: http://myip:myport/
 
This is the key you will have to pass with every HTTP request to the API, either to get or write values.
All API calls must contain the apikey parameter with the value above.
To know what APIs are enabled do a call to /apis.
 

WIFI

You can configure up to 5 different WiFi networks. The device will try to connect in order of signal strength.

MQTT

Configure an MQTT broker in your network and you will be able to change the switch status via an MQTT message. Leave the server field empty to disable MQTT.

 
This is the fingerprint for the SSL certificate of the server.
You can get it using https://www.grc.com/fingerprints.htm
or using openssl from a linux box by typing:
$ openssl s_client -connect <host>:<port> < /dev/null 2>/dev/null | openssl x509 -fingerprint -noout -in /dev/stdin
 
This is the root topic for this device. A trailing slash will be added if not preset. The {identifier} placeholder will be replaces by the device hostname.
- <root>/relay/# Send a 0 or a 1 as a payload to this topic to switch it on or off. You can also send a 2 to toggle its current state. Replace # with the switch ID (starting from 0). If the board has only one switch it will be 0.
- <root>/color The device will report the current color in #RRGGBB format to this topic. You can also set the color using this same topic.
- <root>/led/# Send a 0 or a 1 as a payload to this topic to set the onboard LED to the given state, send a 3 to turn it back to WIFI indicator. Replace # with the LED ID (starting from 0). If the board has only one LED it will be 0.
- <root>/button/# For each button in the board subscribe to this topic to know when it is pressed (payload 1) or released (payload 0).
- <root>/status The device will report a 1 to this topic every few minutes. Upon MQTT disconnecting this will be set to 0.
- Other values reported (depending on the build) are: firmware and version, hostname, IP, MAC, signal strenth (RSSI), uptime (in seconds), free heap and power supply.
 
All messages (except the device status) will be included in a JSON payload along with the timestamp and hostname and sent under the <root>/data topic.
Messages will be queued and sent after 100ms, so different messages could be merged into a single payload.
Subscribtions will still be done to single topics.

NTP

Configure your NTP (Network Time Protocol) servers and local configuration to keep your device time up to the second for your location.

Set to 0 for UTC time

DOMOTICZ

Configure the connection to your Domoticz server.

Set to 0 to disable notifications.
Set to 0 to disable notifications.
Set to 0 to disable notifications.
Set to 0 to disable notifications.
Set to 0 to disable notifications.
Set to 0 to disable notifications.
Set to 0 to disable notifications.

INFLUXDB

Configure the connection to your InfluxDB server. Leave the host field empty to disable InfluxDB connection.

POWER

Calibrate your power monitor device. Use a pure resistive load and introduce the expected values for active power, current and voltage. Use the nominal values or a multimeter to get the proper numbers. Set any field to 0 to leave the calibration value untouched.

 
In Watts (W). If you are using a pure resistive load like a bulb this will be writen on it, otherwise use a socket multimeter to get this value.
 
In Volts (V). Enter your the nominal AC voltage for your household or facility, or use multimeter to get this value.
 
In Ampers (A). If you are using a pure resistive load like a bulb this will the ratio between the two previous values, i.e. power / voltage. You can also use a current clamp around one fo the power wires to get this value.
 
Move this switch to ON and press "Update" to revert to factory values.

RFBRIDGE

Sonoff 433 RF Bridge Configuration

To learn a new code click LEARN, the Sonoff RFBridge will beep, then press a button on the remote, the RFBridge will then double beep and the new code should show up. If the device double beeps but the code does not update it has not been properly learnt. Keep trying.

Modify or create new codes manually (all codes must be 18 characters long) and then click SAVE to store them in the device memory. If your controlled device uses the same code to switch ON and OFF, learn the code with the ON button and copy paste it to the OFF input box, then click SAVE on the last one to store the value.

Delete any code clicking the FORGET button.

 Switch  
Leave empty for DNS negotiation
Set when using a static IP
Usually 255.255.255.0 for /24 networks
Set the Domain Name Server IP to use when using a static IP
Set to 0 to disable notifications.