// ----------------------------------------------------------------------------- // Configuration HELP // ----------------------------------------------------------------------------- // // MANUFACTURER: Name of the manufacturer of the board ("string") // DEVICE: Name of the device ("string") // BUTTON#_PIN: GPIO for the n-th button (1-based, up to 4 buttons) // BUTTON#_RELAY: Relay number that will be bind to the n-th button (1-based) // BUTTON#_MODE: A mask of options (BUTTON_PUSHBUTTON and BUTTON_SWITCH cannot be together) // - BUTTON_PUSHBUTTON: button event is fired when released // - BUTTON_SWITCH: button event is fired when pressed or released // - BUTTON_DEFAULT_HIGH: there is a pull up in place // - BUTTON_SET_PULLUP: set pullup by software // RELAY#_PIN: GPIO for the n-th relay (1-based, up to 8 relays) // RELAY#_TYPE: Relay can be RELAY_TYPE_NORMAL, RELAY_TYPE_INVERSE, RELAY_TYPE_LATCHED or RELAY_TYPE_LATCHED_INVERSE // LED#_PIN: GPIO for the n-th LED (1-based, up to 8 LEDs) // LED#_PIN_INVERSE: LED has inversed logic (lit when pulled down) // LED#_MODE: Check general.h for LED_MODE_% // LED#_RELAY: Linked relay (1-based) // // Besides, other hardware specific information should be stated here // ----------------------------------------------------------------------------- // ESPurna Core // ----------------------------------------------------------------------------- #if defined(ESPURNA_CORE) // This is a special device targeted to generate a light-weight binary image // meant to be able to do two-step-updates: // https://github.com/xoseperez/espurna/wiki/TwoStepUpdates // Info #define MANUFACTURER "ESPRESSIF" #define DEVICE "ESPURNA_CORE" // Disable non-core modules #define ALEXA_SUPPORT 0 #define BROKER_SUPPORT 0 #define DOMOTICZ_SUPPORT 0 #define HOMEASSISTANT_SUPPORT 0 #define I2C_SUPPORT 0 #define MQTT_SUPPORT 0 #define NTP_SUPPORT 0 #define SCHEDULER_SUPPORT 0 #define SENSOR_SUPPORT 0 #define THINGSPEAK_SUPPORT 0 #define WEB_SUPPORT 0 // ----------------------------------------------------------------------------- // Development boards // ----------------------------------------------------------------------------- #elif defined(NODEMCU_LOLIN) // Info #define MANUFACTURER "NODEMCU" #define DEVICE "LOLIN" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #elif defined(WEMOS_D1_MINI_RELAYSHIELD) // Info #define MANUFACTURER "WEMOS" #define DEVICE "D1_MINI_RELAYSHIELD" // Buttons // No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems #define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND, // it's the same as using a Wemos one button shield #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // When Wemos relay shield is connected GPIO5 (D1) is used for relay, // so I2C must be remapped to other pins #define I2C_SDA_PIN 12 // D6 #define I2C_SCL_PIN 14 // D5 #elif defined(WEMOS_D1_TARPUNA_SHIELD) // Info #define MANUFACTURER "WEMOS" #define DEVICE "D1_TARPUNA_SHIELD" // ----------------------------------------------------------------------------- // ESPurna // ----------------------------------------------------------------------------- #elif defined(TINKERMAN_ESPURNA_H06) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_H06" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Normal pushbutton #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_INVERSE // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 2 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(TINKERMAN_ESPURNA_H08) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_H08" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Normal pushbutton #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 5 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(TINKERMAN_ESPURNA_SWITCH) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_SWITCH" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Touch button #define BUTTON1_MODE BUTTON_PUSHBUTTON #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_INVERSE // ----------------------------------------------------------------------------- // Itead Studio boards // ----------------------------------------------------------------------------- #elif defined(ITEAD_SONOFF_BASIC) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_BASIC" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 14 #define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON2_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_RF) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_RF" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 14 #define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON2_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_TH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_TH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Jack is connected to GPIO14 (and with a small hack to GPIO4) #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 14 #ifndef DHT_SUPPORT #define DHT_SUPPORT 1 #endif #define DHT_PIN 14 //#define I2C_SDA_PIN 4 //#define I2C_SCL_PIN 14 #elif defined(ITEAD_SONOFF_SV) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_SV" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SLAMPHER) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SLAMPHER" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_S20) // Info #define MANUFACTURER "ITEAD" #define DEVICE "S20" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_TOUCH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_TOUCH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_POW) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_POW" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 15 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 5 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(ITEAD_SONOFF_POW_R2) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_POW_R2" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 15 #define LED1_PIN_INVERSE 0 // CSE7766 #ifndef CSE7766_SUPPORT #define CSE7766_SUPPORT 1 #endif #define CSE7766_PIN 1 #elif defined(ITEAD_SONOFF_DUAL) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_DUAL" #define SERIAL_BAUDRATE 19230 #define RELAY_PROVIDER RELAY_PROVIDER_DUAL #define DUMMY_RELAY_COUNT 2 #define DEBUG_SERIAL_SUPPORT 0 // Buttons #define BUTTON3_RELAY 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_DUAL_R2) #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_DUAL_R2" // Buttons #define BUTTON1_PIN 0 // Button 0 on header #define BUTTON2_PIN 9 // Button 1 on header #define BUTTON3_PIN 10 // Physical button #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 1 #define BUTTON1_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_4CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_4CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON4_PIN 14 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 #define BUTTON4_RELAY 4 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_4CH_PRO) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_4CH_PRO" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON4_PIN 14 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 #define BUTTON4_RELAY 4 // Sonoff 4CH Pro uses a secondary STM32 microcontroller to handle // buttons and relays, but it also forwards button presses to the ESP8285. // This allows ESPurna to handle button presses -almost- the same way // as with other devices except: // * Double click seems to break/disable the button on the STM32 side // * With S6 switch to 1 (self-locking and inching modes) everything's OK // * With S6 switch to 0 (interlock mode) if there is a relay ON // and you click on another relay button, the STM32 sends a "press" // event for the button of the first relay (to turn it OFF) but it // does not send a "release" event. It's like it's holding the // button down since you can see it is still LOW. // Whatever reason the result is that it may actually perform a // long click or long-long click. // The configuration below make the button toggle the relay on press events // and disables any possibly harmful combination with S6 set to 0. // If you are sure you will only use S6 to 1 you can comment the // BUTTON1_LNGCLICK and BUTTON1_LNGLNGCLICK options below to recover the // reset mode and factory reset functionalities, or link other actions like // AP mode in the commented line below. #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE //#define BUTTON1_LNGCLICK BUTTON_MODE_AP #define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE #define BUTTON2_PRESS BUTTON_MODE_TOGGLE #define BUTTON2_CLICK BUTTON_MODE_NONE #define BUTTON3_PRESS BUTTON_MODE_TOGGLE #define BUTTON3_CLICK BUTTON_MODE_NONE #define BUTTON4_PRESS BUTTON_MODE_TOGGLE #define BUTTON4_CLICK BUTTON_MODE_NONE // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_1CH_INCHING) // The inching functionality is managed by a misterious IC in the board. // You cannot control the inching button and functionality from the ESP8266 // Besides, enabling the inching functionality using the hardware button // will result in the relay switching on and off continuously. // Fortunately the unkown IC keeps memory of the hardware inching status // so you can just disable it and forget. The inching LED must be lit. // You can still use the pulse options from the web interface // without problem. // Info #define MANUFACTURER "ITEAD" #define DEVICE "1CH_INCHING" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_MOTOR) // Info #define MANUFACTURER "ITEAD" #define DEVICE "MOTOR" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_BNSZ01) // Info #define MANUFACTURER "ITEAD" #define DEVICE "BNSZ01" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 1 #define LIGHT_CH1_PIN 12 #define LIGHT_CH1_INVERSE 0 #elif defined(ITEAD_SONOFF_RFBRIDGE) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_RFBRIDGE" #define RELAY_PROVIDER RELAY_PROVIDER_RFBRIDGE // Number of virtual switches #ifndef DUMMY_RELAY_COUNT #define DUMMY_RELAY_COUNT 8 #endif // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // RFB Direct hack thanks to @wildwiz // https://github.com/xoseperez/espurna/wiki/Hardware-Itead-Sonoff-RF-Bridge---Direct-Hack #ifndef RFB_DIRECT #define RFB_DIRECT 0 #endif #ifndef RFB_RX_PIN #define RFB_RX_PIN 4 // GPIO for RX when RFB_DIRECT #endif #ifndef RFB_TX_PIN #define RFB_TX_PIN 5 // GPIO for TX when RFB_DIRECT #endif // When using un-modified harware, ESPurna communicates with the secondary // MCU EFM8BB1 via UART at 19200 bps so we need to change the speed of // the port and remove UART noise on serial line #if not RFB_DIRECT #define SERIAL_BAUDRATE 19200 #define DEBUG_SERIAL_SUPPORT 0 #endif #elif defined(ITEAD_SONOFF_B1) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_B1" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define MY92XX_MODEL MY92XX_MODEL_MY9231 #define MY92XX_CHIPS 2 #define MY92XX_DI_PIN 12 #define MY92XX_DCKI_PIN 14 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 4, 3, 5, 0, 1 #define LIGHT_WHITE_FACTOR (0.1) // White LEDs are way more bright in the B1 #elif defined(ITEAD_SONOFF_LED) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_LED" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 12 // Cold white #define LIGHT_CH2_PIN 14 // Warm white #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #elif defined(ITEAD_SONOFF_T1_1CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_1CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_T1_2CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_2CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_MODE_TOGGLE #define BUTTON2_CLICK BUTTON_MODE_NONE #define BUTTON2_DBLCLICK BUTTON_MODE_NONE #define BUTTON2_LNGCLICK BUTTON_MODE_NONE #define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_T1_3CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_3CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_MODE_TOGGLE #define BUTTON2_CLICK BUTTON_MODE_NONE #define BUTTON2_DBLCLICK BUTTON_MODE_NONE #define BUTTON2_LNGCLICK BUTTON_MODE_NONE #define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_PRESS BUTTON_MODE_TOGGLE #define BUTTON3_CLICK BUTTON_MODE_NONE #define BUTTON3_DBLCLICK BUTTON_MODE_NONE #define BUTTON3_LNGCLICK BUTTON_MODE_NONE #define BUTTON3_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_S31) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_S31" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Disable UART noise #define DEBUG_SERIAL_SUPPORT 0 // CSE7766 #define CSE7766_SUPPORT 1 #define CSE7766_PIN 1 // ----------------------------------------------------------------------------- // YJZK // ----------------------------------------------------------------------------- #elif defined(YJZK_SWITCH_2CH) // Info #define MANUFACTURER "YJZK" #define DEVICE "SWITCH_2CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Electrodragon boards // ----------------------------------------------------------------------------- #elif defined(ELECTRODRAGON_WIFI_IOT) // Info #define MANUFACTURER "ELECTRODRAGON" #define DEVICE "WIFI_IOT" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 2 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 16 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // WorkChoice ecoPlug // ----------------------------------------------------------------------------- #elif defined(WORKCHOICE_ECOPLUG) // Info #define MANUFACTURER "WORKCHOICE" #define DEVICE "ECOPLUG" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // AI Thinker // ----------------------------------------------------------------------------- #elif defined(AITHINKER_AI_LIGHT) // Info #define MANUFACTURER "AITHINKER" #define DEVICE "AI_LIGHT" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 13 #define MY92XX_DCKI_PIN 15 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // LED Controller // ----------------------------------------------------------------------------- #elif defined(MAGICHOME_LED_CONTROLLER) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "LED_CONTROLLER" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 13 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_PIN 4 #define IR_BUTTON_SET 1 #elif defined(MAGICHOME_LED_CONTROLLER_20) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "LED_CONTROLLER_20" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_PIN 4 #define IR_BUTTON_SET 1 // ----------------------------------------------------------------------------- // HUACANXING H801 & H802 // ----------------------------------------------------------------------------- #elif defined(HUACANXING_H801) // Info #define MANUFACTURER "HUACANXING" #define DEVICE "H801" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define DEBUG_PORT Serial1 #define SERIAL_RX_ENABLED 1 // LEDs #define LED1_PIN 5 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 15 // RED #define LIGHT_CH2_PIN 13 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 14 // WHITE1 #define LIGHT_CH5_PIN 4 // WHITE2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(HUACANXING_H802) // Info #define MANUFACTURER "HUACANXING" #define DEVICE "H802" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define DEBUG_PORT Serial1 #define SERIAL_RX_ENABLED 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 14 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Jan Goedeke Wifi Relay // https://github.com/JanGoe/esp8266-wifi-relay // ----------------------------------------------------------------------------- #elif defined(JANGOE_WIFI_RELAY_NC) // Info #define MANUFACTURER "JANGOE" #define DEVICE "WIFI_RELAY_NC" // Buttons #define BUTTON1_PIN 12 #define BUTTON2_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 2 #define RELAY2_PIN 14 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_TYPE RELAY_TYPE_INVERSE #elif defined(JANGOE_WIFI_RELAY_NO) // Info #define MANUFACTURER "JANGOE" #define DEVICE "WIFI_RELAY_NO" // Buttons #define BUTTON1_PIN 12 #define BUTTON2_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 2 #define RELAY2_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // Jorge García Wifi+Relays Board Kit // https://www.tindie.com/products/jorgegarciadev/wifi--relays-board-kit // https://github.com/jorgegarciadev/wifikit // ----------------------------------------------------------------------------- #elif defined(JORGEGARCIA_WIFI_RELAYS) // Info #define MANUFACTURER "JORGEGARCIA" #define DEVICE "WIFI_RELAYS" // Relays #define RELAY1_PIN 0 #define RELAY2_PIN 2 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_TYPE RELAY_TYPE_INVERSE // ----------------------------------------------------------------------------- // WiFi MQTT Relay / Thermostat // ----------------------------------------------------------------------------- #elif defined(OPENENERGYMONITOR_MQTT_RELAY) // Info #define MANUFACTURER "OPENENERGYMONITOR" #define DEVICE "MQTT_RELAY" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 16 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // WiOn 50055 Indoor Wi-Fi Wall Outlet & Tap // https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50050-Indoor-Wi-Fi-Outlet-Wireless-Switch-Programmable-Timer-%2F263112281551 // https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50055-Indoor-Wi-Fi-Wall-Tap-Monitor-Energy-Usage-Wireless-Smart-Switch-%2F263020837777 // ----------------------------------------------------------------------------- #elif defined(WION_50055) // Currently untested, does not support energy monitoring // Info #define MANUFACTURER "WION" #define DEVICE "50055" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // EX-Store Wifi Relay v3.1 // https://ex-store.de/ESP8266-WiFi-Relay-V31 // ----------------------------------------------------------------------------- #elif defined(EXS_WIFI_RELAY_V31) // Untested // Info #define MANUFACTURER "EXS" #define DEVICE "WIFI_RELAY_V31" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 13 #define RELAY1_TYPE RELAY_TYPE_LATCHED #define RELAY1_RESET_PIN 12 // ----------------------------------------------------------------------------- // V9261F // ----------------------------------------------------------------------------- #elif defined(GENERIC_V9261F) // Info #define MANUFACTURER "GENERIC" #define DEVICE "V9261F" #define ALEXA_SUPPORT 0 // V9261F #define V9261F_SUPPORT 1 #define V9261F_PIN 2 #define V9261F_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // ECH1560 // ----------------------------------------------------------------------------- #elif defined(GENERIC_ECH1560) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ECH1560" #define ALEXA_SUPPORT 0 // ECH1560 #define ECH1560_SUPPORT 1 #define ECH1560_CLK_PIN 4 #define ECH1560_MISO_PIN 5 #define ECH1560_INVERTED 0 // ----------------------------------------------------------------------------- // ESPLive // https://github.com/ManCaveMade/ESP-Live // ----------------------------------------------------------------------------- #elif defined(MANCAVEMADE_ESPLIVE) // Info #define MANUFACTURER "MANCAVEMADE" #define DEVICE "ESPLIVE" // Buttons #define BUTTON1_PIN 4 #define BUTTON2_PIN 5 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // DS18B20 #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 2 #define DALLAS_UPDATE_INTERVAL 5000 #define TEMPERATURE_MIN_CHANGE 1.0 // ----------------------------------------------------------------------------- // QuinLED // http://blog.quindorian.org/2017/02/esp8266-led-lighting-quinled-v2-6-pcb.html // ----------------------------------------------------------------------------- #elif defined(INTERMITTECH_QUINLED) // Info #define MANUFACTURER "INTERMITTECH" #define DEVICE "QUINLED" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 5 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 0 #define LIGHT_CH2_PIN 2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 // ----------------------------------------------------------------------------- // Arilux AL-LC06 // ----------------------------------------------------------------------------- #elif defined(ARILUX_AL_LC01) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC01" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 3 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #elif defined(ARILUX_AL_LC02) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC02" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #elif defined(ARILUX_AL_LC06) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC06" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE1 #define LIGHT_CH5_PIN 5 // WHITE2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(ARILUX_AL_LC11) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC11" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 13 // WHITE1 #define LIGHT_CH5_PIN 12 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(ARILUX_E27) // Info #define MANUFACTURER "ARILUX" #define DEVICE "E27" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 13 #define MY92XX_DCKI_PIN 15 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // XENON SM-PW701U // ----------------------------------------------------------------------------- #elif defined(XENON_SM_PW702U) // Info #define MANUFACTURER "XENON" #define DEVICE "SM_PW702U" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // AUTHOMETION LYT8266 // https://authometion.com/shop/en/home/13-lyt8266.html // ----------------------------------------------------------------------------- #elif defined(AUTHOMETION_LYT8266) // Info #define MANUFACTURER "AUTHOMETION" #define DEVICE "LYT8266" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 13 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 2 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_ENABLE_PIN 15 #elif defined(GIZWITS_WITTY_CLOUD) // Info #define MANUFACTURER "GIZWITS" #define DEVICE "WITTY_CLOUD" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Buttons #define BUTTON1_PIN 4 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define ANALOG_SUPPORT 1 // LEDs #define LED1_PIN 2 // BLUE build-in #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 3 #define LIGHT_CH1_PIN 15 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 // ----------------------------------------------------------------------------- // KMC 70011 // https://www.amazon.com/KMC-Monitoring-Required-Control-Compatible/dp/B07313TH7B // ----------------------------------------------------------------------------- #elif defined(KMC_70011) // Info #define MANUFACTURER "KMC" #define DEVICE "70011" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor // ----------------------------------------------------------------------------- // Euromate (?) Wifi Stecker Shuko // https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko/p/2291706 // Thanks to @Geitde // ----------------------------------------------------------------------------- #elif defined(EUROMATE_WIFI_STECKER_SCHUKO) // Info #define MANUFACTURER "EUROMATE" #define DEVICE "WIFI_STECKER_SCHUKO" // Buttons #define BUTTON1_PIN 14 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // The relay in the device is not a bistable (latched) relay. // The device is reported to have a flip-flop circuit to drive the relay // So @Geitde hack is still the only possible // Hack: drive GPIO12 low and use GPIO5 as normal relay pin: #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define LED2_PIN 12 /* DUMMY: exploit default off state for GPIO12=low */ #define LED2_PIN_INVERSE 0 // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Generic 8CH // ----------------------------------------------------------------------------- #elif defined(GENERIC_8CH) // Info #define MANUFACTURER "GENERIC" #define DEVICE "8CH" // Relays #define RELAY1_PIN 0 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 2 #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_PIN 4 #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_PIN 5 #define RELAY4_TYPE RELAY_TYPE_NORMAL #define RELAY5_PIN 12 #define RELAY5_TYPE RELAY_TYPE_NORMAL #define RELAY6_PIN 13 #define RELAY6_TYPE RELAY_TYPE_NORMAL #define RELAY7_PIN 14 #define RELAY7_TYPE RELAY_TYPE_NORMAL #define RELAY8_PIN 15 #define RELAY8_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // STM RELAY // ----------------------------------------------------------------------------- #elif defined(STM_RELAY) // Info #define MANUFACTURER "STM_RELAY" #define DEVICE "2CH" // Relays #define DUMMY_RELAY_COUNT 2 #define RELAY_PROVIDER RELAY_PROVIDER_STM // Remove UART noise on serial line #define DEBUG_SERIAL_SUPPORT 0 // ----------------------------------------------------------------------------- // Tonbux Powerstrip02 // ----------------------------------------------------------------------------- #elif defined(TONBUX_POWERSTRIP02) // Info #define MANUFACTURER "TONBUX" #define DEVICE "POWERSTRIP02" // Buttons #define BUTTON1_PIN 5 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 0 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_PIN 13 #define RELAY2_TYPE RELAY_TYPE_INVERSE #define RELAY3_PIN 12 #define RELAY3_TYPE RELAY_TYPE_INVERSE #define RELAY4_PIN 14 #define RELAY4_TYPE RELAY_TYPE_INVERSE // Not a relay. USB ports on/off #define RELAY5_PIN 16 #define RELAY5_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // 1 blue led #define LED1_PIN_INVERSE 1 #define LED2_PIN 3 // 3 red leds #define LED2_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Lingan SWA1 // ----------------------------------------------------------------------------- #elif defined(LINGAN_SWA1) // Info #define MANUFACTURER "LINGAN" #define DEVICE "SWA1" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // HEYGO HY02 // ----------------------------------------------------------------------------- #elif defined(HEYGO_HY02) // Info #define MANUFACTURER "HEYGO" #define DEVICE "HY02" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Maxcio W-US002S // ----------------------------------------------------------------------------- #elif defined(MAXCIO_WUS002S) // Info #define MANUFACTURER "MAXCIO" #define DEVICE "WUS002S" // Buttons #define BUTTON1_PIN 2 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 3 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_CURRENT_R 0.002 // Current resistor #define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor // ----------------------------------------------------------------------------- // YiDian XS-SSA05 // ----------------------------------------------------------------------------- #elif defined(YIDIAN_XSSSA05) // Info #define MANUFACTURER "YIDIAN" #define DEVICE "XSSSA05" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 3 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_CURRENT_R 0.001 // Current resistor #define HLW8012_VOLTAGE_R_UP ( 2 * 1200000 ) // Upstream voltage resistor // ----------------------------------------------------------------------------- // TONBUX XS-SSA06 // ----------------------------------------------------------------------------- #elif defined(TONBUX_XSSSA06) // Info #define MANUFACTURER "TONBUX" #define DEVICE "XSSSA06" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // R - 8 rgb led ring #define LED1_PIN_INVERSE 0 #define LED2_PIN 5 // G #define LED2_PIN_INVERSE 0 #define LED3_PIN 2 // B #define LED3_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // GREEN ESP8266 RELAY MODULE // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180323113846&SearchText=Green+ESP8266 // ----------------------------------------------------------------------------- #elif defined(GREEN_ESP8266RELAY) // Info #define MANUFACTURER "GREEN" #define DEVICE "ESP8266RELAY" // Buttons // Not a button but input via Optocoupler #define BUTTON1_PIN 5 #define BUTTON1_MODE BUTTON_PUSHBUTTON #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Henrique Gravina ESPIKE // https://github.com/Henriquegravina/Espike // ----------------------------------------------------------------------------- #elif defined(IKE_ESPIKE) #define MANUFACTURER "IKE" #define DEVICE "ESPIKE" #define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_PIN 13 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PIN 12 #define BUTTON2_RELAY 2 #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_PIN 14 #define BUTTON3_RELAY 2 #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 5 #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_PIN 16 #define RELAY3_TYPE RELAY_TYPE_NORMAL #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // SWIFITCH // https://github.com/ArnieX/swifitch // ----------------------------------------------------------------------------- #elif defined(ARNIEX_SWIFITCH) // Info #define MANUFACTURER "ARNIEX" #define DEVICE "SWIFITCH" // Buttons #define BUTTON1_PIN 4 // D2 #define BUTTON1_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON1_PRESS BUTTON_MODE_NONE #define BUTTON1_CLICK BUTTON_MODE_TOGGLE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE // Relays #define RELAY1_PIN 5 // D1 #define RELAY1_TYPE RELAY_TYPE_INVERSE // LEDs #define LED1_PIN 12 // D6 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // ESP-01S RELAY v4.0 // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404024035&SearchText=esp-01s+relay // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_RELAY_V40) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_RELAY_40" // Relays #define RELAY1_PIN 0 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // ESP-01S RGB LED v1.0 (some sold with ws2818) // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404023816&SearchText=esp-01s+led+controller // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_RGBLED_V10) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_RGBLED_10" // This board is sold as RGB LED module BUT it has on board 3 pin ph2.0 connector (VCC, GPIO2, GND) // so, if you wish, you may connect LED, BUTTON, RELAY, SENSOR etc. // Buttons //#define BUTTON1_PIN 2 // Relays //#define RELAY1_PIN 2 // LEDs #define LED1_PIN 2 // ----------------------------------------------------------------------------- // ESP-01S DHT11 v1.0 // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180410105907&SearchText=esp-01s+dht11 // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_DHT11_V10) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_DHT11_10" // DHT11 #ifndef DHT_SUPPORT #define DHT_SUPPORT 1 #endif #define DHT_PIN 2 // ----------------------------------------------------------------------------- // ESP-01S DS18B20 v1.0 // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180410105933&SearchText=esp-01s+ds18b20 // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_DS18B20_V10) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_DS18B20_10" // DB18B20 #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 2 // ----------------------------------------------------------------------------- // Heltec Touch Relay // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180408043114&SearchText=esp8266+touch+relay // ----------------------------------------------------------------------------- #elif defined(HELTEC_TOUCHRELAY) // Info #define MANUFACTURER "HELTEC" #define DEVICE "TOUCH_RELAY" // Buttons #define BUTTON1_PIN 14 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // Zhilde ZLD-EU44-W // http://www.zhilde.com/product/60705150109-805652505/EU_WiFi_Surge_Protector_Extension_Socket_4_Outlets_works_with_Amazon_Echo_Smart_Power_Strip.html // ----------------------------------------------------------------------------- #elif defined(ZHILDE_EU44_W) // Info #define MANUFACTURER "ZHILDE" #define DEVICE "EU44_W" // Based on the reporter, this product uses GPIO1 and 3 for the button // and onboard LED, so hardware serial should be disabled... #define DEBUG_SERIAL_SUPPORT 0 // Buttons #define BUTTON1_PIN 3 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 5 #define RELAY2_PIN 4 #define RELAY3_PIN 12 #define RELAY4_PIN 13 #define RELAY5_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL #define RELAY5_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 1 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // TEST boards (do not use!!) // ----------------------------------------------------------------------------- #elif defined(TRAVIS01) // Info #define MANUFACTURER "TravisCI" #define DEVICE "Virtual board 01" // Some buttons - pin 0 #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Some relays - pin 1 #define RELAY1_PIN 1 #define RELAY1_TYPE RELAY_TYPE_NORMAL // Some LEDs - pin 2 #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // A bit of I2C - pins 3,4 #define I2C_SDA_PIN 3 #define I2C_SCL_PIN 4 // And, as they say in "From Dusk till Dawn": // This is a sensor blow out! // Alright, we got white sensor, black sensor, spanish sensor, yellow sensor. We got hot sensor, cold sensor. // We got wet sensor. We got smelly sensor. We got hairy sensor, bloody sensor. We got snapping sensor. // We got silk sensor, velvet sensor, naugahyde sensor. We even got horse sensor, dog sensor, chicken sensor. // C'mon, you want sensor, come on in sensor lovers! // If we don’t got it, you don't want it! #define AM2320_SUPPORT 1 #define BH1750_SUPPORT 1 #define BMX280_SUPPORT 1 #define SHT3X_I2C_SUPPORT 1 #define EMON_ADC121_SUPPORT 1 #define EMON_ADS1X15_SUPPORT 1 #define SHT3X_I2C_SUPPORT 1 #define SI7021_SUPPORT 1 // A bit of lights - pin 5 #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define LIGHT_CHANNELS 1 #define LIGHT_CH1_PIN 5 #define LIGHT_CH1_INVERSE 0 // A bit of HLW8012 - pins 6,7,8 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 6 #define HLW8012_CF1_PIN 7 #define HLW8012_CF_PIN 8 // A bit of Dallas - pin 9 #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 9 // A bit of ECH1560 - pins 10,11, 12 #ifndef ECH1560_SUPPORT #define ECH1560_SUPPORT 1 #endif #define ECH1560_CLK_PIN 10 #define ECH1560_MISO_PIN 11 #define ECH1560_INVERTED 12 #elif defined(TRAVIS02) // Relay provider dual #define MANUFACTURER "TravisCI" #define DEVICE "Virtual board 02" // A bit of CSE7766 - pin 1 #ifndef CSE7766_SUPPORT #define CSE7766_SUPPORT 1 #endif #define CSE7766_PIN 1 // Relay type dual - pins 2,3 #define RELAY_PROVIDER RELAY_PROVIDER_DUAL #define RELAY1_PIN 2 #define RELAY2_PIN 3 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // IR - pin 4 #define IR_SUPPORT 1 #define IR_PIN 4 #define IR_BUTTON_SET 1 // A bit of DHT - pin 5 #ifndef DHT_SUPPORT #define DHT_SUPPORT 1 #endif #define DHT_PIN 5 // A bit of TMP3X (analog) #define TMP3X_SUPPORT 1 // A bit of EVENTS - pin 10 #define EVENTS_SUPPORT 1 #define EVENTS_PIN 6 // HC-RS04 #define HCSR04_SUPPORT 1 #define HCSR04_TRIGGER 7 #define HCSR04_ECHO 8 // MHZ19 #define MHZ19_SUPPORT 1 #define MHZ19_RX_PIN 9 #define MHZ19_TX_PIN 10 // PZEM004T #define PZEM004T_SUPPORT 0 // not working? #define PZEM004T_RX_PIN 11 #define PZEM004T_TX_PIN 12 // V9261F #define V9261F_SUPPORT 1 #define V9261F_PIN 13 // GUVAS12SD #define GUVAS12SD_SUPPORT 1 #define GUVAS12SD_PIN 14 #elif defined(TRAVIS03) // Relay provider light/my92XX #define MANUFACTURER "TravisCI" #define DEVICE "Virtual board 03" // MY9231 Light - pins 1,2 #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 #define LIGHT_CHANNELS 5 #define MY92XX_MODEL MY92XX_MODEL_MY9231 #define MY92XX_CHIPS 2 #define MY92XX_DI_PIN 1 #define MY92XX_DCKI_PIN 2 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 4, 3, 5, 0, 1 // A bit of Analog EMON (analog) #ifndef EMON_ANALOG_SUPPORT #define EMON_ANALOG_SUPPORT 1 #endif #endif // ----------------------------------------------------------------------------- // Check definitions // ----------------------------------------------------------------------------- #if not defined(MANUFACTURER) || not defined(DEVICE) #error "UNSUPPORTED HARDWARE!!" #endif