// -----------------------------------------------------------------------------
// Configuration HELP
// -----------------------------------------------------------------------------
//
// Required:
//
// MANUFACTURER: Name of the manufacturer of the board ("string")
// DEVICE: Name of the device ("string")
//
// For example, some configuration options for BUTTON, RELAY and LED modules.
// See general.h, defaults.h and types.h for all of the available flags.
//
// BUTTON[1-8]_CONFIG: Configuration mask (note that BUTTON_PUSHBUTTON and BUTTON_SWITCH cannot be together)
// - BUTTON_PUSHBUTTON: button event is fired when released
// - BUTTON_SWITCH: button event is fired when pressed or released
// - BUTTON_DEFAULT_HIGH: there is a pull up in place, HIGH is default state
// - BUTTON_DEFAULT_LOW: there is a pull down in place, LOW is default state
// - BUTTON_DEFAULT_BOOT: use state that we read on firmware boot
// - BUTTON_SET_PULLUP: set pullup by software
// - BUTTON_SET_PULLDOWN: set pulldown by software (esp8266: only GPIO16)
// BUTTON[1-8]_... actions: Check types.h for BUTTONx_ACTION_...
// BUTTON[1-8]_PIN: GPIO for the n-th button (1-based, up to 8 buttons)
// BUTTON[1-8]_PROVIDER: Check types.h for the BUTTON_PROVIDER_...
// BUTTON[1-8]_RELAY: Relay number that will be bound to the n-th button (when ACTION is set to ON, OFF or TOGGLE; 1-based)
//
// RELAY[1-8]_PIN: GPIO for the n-th relay (1-based, up to 8 relays)
// RELAY[1-8]_TYPE: Relay can be RELAY_TYPE_NORMAL, RELAY_TYPE_INVERSE, RELAY_TYPE_LATCHED or RELAY_TYPE_LATCHED_INVERSE
//
// LED[1-8]_PIN: GPIO for the n-th LED (1-based, up to 8 LEDs)
// LED[1-8]_PIN_INVERSE: LED has inversed logic (lit when pulled down)
// LED[1-8]_MODE: Check types.h for LED_MODE_...
// LED[1-8]_RELAY: Linked relay (1-based)
//
// Besides, other hardware specific information should be stated here
#pragma once
// -----------------------------------------------------------------------------
// Custom hardware
// -----------------------------------------------------------------------------
#if defined(MANUFACTURER) and defined(DEVICE)
// user has defined custom hardware, no need to check anything else
// -----------------------------------------------------------------------------
// ESPurna Core
// -----------------------------------------------------------------------------
#elif defined(ESPURNA_CORE)
// This is a special device targeted to generate a light-weight binary image
// meant to be able to do two-step-updates:
// https://github.com/xoseperez/espurna/wiki/TwoStepUpdates
// Info
#define MANUFACTURER "ESPURNA"
#define DEVICE "CORE"
// Disable non-core modules
#define ALEXA_SUPPORT 0
#define API_SUPPORT 0
#define BROKER_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
#define DEBUG_TELNET_SUPPORT 0
#define DEBUG_WEB_SUPPORT 0
#define DOMOTICZ_SUPPORT 0
#define HOMEASSISTANT_SUPPORT 0
#define I2C_SUPPORT 0
#define MQTT_SUPPORT 0
#define NTP_SUPPORT 0
#define RPN_RULES_SUPPORT 0
#define SCHEDULER_SUPPORT 0
#define SENSOR_SUPPORT 0
#define THINGSPEAK_SUPPORT 0
#define WEB_SUPPORT 0
// Extra light-weight image
//#define BUTTON_SUPPORT 0 // don't need / have buttons
//#define LED_SUPPORT 0 // don't need wifi indicator
//#define RELAY_SUPPORT 0 // don't need to preserve pin state between resets
//#define OTA_ARDUINOOTA_SUPPORT 0 // when only using `ota` command
//#define MDNS_SERVER_SUPPORT 0 //
//#define TELNET_SUPPORT 0 // when only using espota.py
//#define TERMINAL_SUPPORT 0 //
#elif defined(ESPURNA_CORE_WEBUI)
// This is a special device with no specific hardware
// with the basics to easily upgrade it to a device-specific image
// Info
#define MANUFACTURER "ESPURNA"
#define DEVICE "CORE_WEBUI"
// Disable non-core modules
#define ALEXA_SUPPORT 0
#define API_SUPPORT 0
#define BROKER_SUPPORT 0
#define DOMOTICZ_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
//#define DEBUG_TELNET_SUPPORT 0
//#define DEBUG_WEB_SUPPORT 0
#define HOMEASSISTANT_SUPPORT 0
#define I2C_SUPPORT 0
#define MQTT_SUPPORT 0
#define NTP_SUPPORT 0
#define SCHEDULER_SUPPORT 0
#define SENSOR_SUPPORT 0
#define THINGSPEAK_SUPPORT 0
//#define WEB_SUPPORT 0
// Extra light-weight image
#define BUTTON_SUPPORT 0
#define LED_SUPPORT 0
//#define MDNS_SERVER_SUPPORT 0
//#define TELNET_SUPPORT 0
//#define TERMINAL_SUPPORT 0
// -----------------------------------------------------------------------------
// Development boards
// -----------------------------------------------------------------------------
#elif defined(NODEMCU_LOLIN)
// Info
#define MANUFACTURER "NODEMCU"
#define DEVICE "LOLIN"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Hidden button will enter AP mode if dblclick and reset the device when long-long-clicked
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// Light
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#elif defined(NODEMCU_BASIC)
// Info
// Generic NodeMCU Board without any buttons or relays connected.
#define MANUFACTURER "NODEMCU"
#define DEVICE "BASIC"
#elif defined(WEMOS_D1_MINI)
// Info
#define MANUFACTURER "WEMOS"
#define DEVICE "D1_MINI"
// Buttons
// No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems
#define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND,
// it's the same as using a Wemos one button shield
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define I2C_SDA_PIN 4 // D2
#define I2C_SCL_PIN 5 // D1
#elif defined(WEMOS_D1_MINI_RELAYSHIELD)
// Info
#define MANUFACTURER "WEMOS"
#define DEVICE "D1_MINI_RELAYSHIELD"
// Buttons
// No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems
#define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND,
// it's the same as using a Wemos one button shield
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LED
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// When Wemos relay shield is connected GPIO5 (D1) is used for relay,
// so I2C must be remapped to other pins
#define I2C_SDA_PIN 12 // D6
#define I2C_SCL_PIN 14 // D5
#elif defined(WEMOS_D1_TARPUNA_SHIELD)
// Info
#define MANUFACTURER "WEMOS"
#define DEVICE "D1_TARPUNA_SHIELD"
// Relays
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define DHT_SUPPORT 1
#define DHT_PIN 12
// -----------------------------------------------------------------------------
// ESPurna
// -----------------------------------------------------------------------------
#elif defined(TINKERMAN_ESPURNA_H06)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_H06"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Normal pushbutton
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 2
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(TINKERMAN_ESPURNA_H08)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_H08"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Normal pushbutton
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 5
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(TINKERMAN_ESPURNA_SWITCH)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_SWITCH"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Touch button
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// Check http://tinkerman.cat/rfm69-wifi-gateway/
#elif defined(TINKERMAN_RFM69GW)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "RFM69GW"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// RFM69GW
#define RFM69_SUPPORT 1
// Disable non-core modules
#define ALEXA_SUPPORT 0
#define DOMOTICZ_SUPPORT 0
#define HOMEASSISTANT_SUPPORT 0
#define I2C_SUPPORT 0
#define SCHEDULER_SUPPORT 0
#define SENSOR_SUPPORT 0
#define THINGSPEAK_SUPPORT 0
// -----------------------------------------------------------------------------
// Itead Studio boards
// -----------------------------------------------------------------------------
#elif defined(ITEAD_SONOFF_BASIC)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_BASIC"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 14
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_RF)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_RF"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 14
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_MINI)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_MINI"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 4
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_BOOT
#define BUTTON2_RELAY 1
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_RELEASE BUTTON_ACTION_TOGGLE
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_TH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_TH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Jack is connected to GPIO14 (and with a small hack to GPIO4)
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 14
#ifndef DHT_SUPPORT
#define DHT_SUPPORT 1
#endif
#define DHT_PIN 14
#define DHT_TYPE DHT_CHIP_SI7021
//#define I2C_SDA_PIN 4
//#define I2C_SCL_PIN 14
#elif defined(ITEAD_SONOFF_SV)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_SV"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SLAMPHER)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SLAMPHER"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_S20)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "S20"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_TOUCH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_TOUCH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_POW)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_POW"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 15
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 5
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(ITEAD_SONOFF_POW_R2)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_POW_R2"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Disable UART noise
#define DEBUG_SERIAL_SUPPORT 0
// CSE7766
#ifndef CSE7766_SUPPORT
#define CSE7766_SUPPORT 1
#endif
#define CSE7766_RX_PIN 3
#elif defined(ITEAD_SONOFF_DUAL)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_DUAL"
#define SERIAL_BAUDRATE 19230
#define RELAY_PROVIDER RELAY_PROVIDER_DUAL
#define DUMMY_RELAY_COUNT 2
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 1
#define BUTTON_PROVIDER_ITEAD_SONOFF_DUAL_SUPPORT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_DUAL_R2)
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_DUAL_R2"
// Buttons
#define BUTTON1_PIN 0 // Button 0 on header
#define BUTTON2_PIN 9 // Button 1 on header
#define BUTTON3_PIN 10 // Physical button
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 1
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_4CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_4CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON4_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
#define BUTTON4_RELAY 4
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_4CH_PRO)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_4CH_PRO"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON4_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
#define BUTTON4_RELAY 4
// Sonoff 4CH Pro uses a secondary STM32 microcontroller to handle
// buttons and relays, but it also forwards button presses to the ESP8285.
// This allows ESPurna to handle button presses -almost- the same way
// as with other devices except:
// * Double click seems to break/disable the button on the STM32 side
// * With S6 switch to 1 (self-locking and inching modes) everything's OK
// * With S6 switch to 0 (interlock mode) if there is a relay ON
// and you click on another relay button, the STM32 sends a "press"
// event for the button of the first relay (to turn it OFF) but it
// does not send a "release" event. It's like it's holding the
// button down since you can see it is still LOW.
// Whatever reason the result is that it may actually perform a
// long click or long-long click.
// The configuration below make the button toggle the relay on press events
// and disables any possibly harmful combination with S6 set to 0.
// If you are sure you will only use S6 to 1 you can comment the
// BUTTON1_LNGCLICK and BUTTON1_LNGLNGCLICK options below to recover the
// reset mode and factory reset functionalities, or link other actions like
// AP mode in the commented line below.
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
//#define BUTTON1_LNGCLICK BUTTON_ACTION_AP
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON3_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON3_CLICK BUTTON_ACTION_NONE
#define BUTTON4_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON4_CLICK BUTTON_ACTION_NONE
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_1CH_INCHING)
// The inching functionality is managed by a misterious IC in the board.
// You cannot control the inching button and functionality from the ESP8266
// Besides, enabling the inching functionality using the hardware button
// will result in the relay switching on and off continuously.
// Fortunately the unkown IC keeps memory of the hardware inching status
// so you can just disable it and forget. The inching LED must be lit.
// You can still use the pulse options from the web interface
// without problem.
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "1CH_INCHING"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_MOTOR)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "MOTOR"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_BNSZ01)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "BNSZ01"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 1
#define LIGHT_CH1_PIN 12
#elif defined(ITEAD_SONOFF_RFBRIDGE)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_RFBRIDGE"
#define RELAY_PROVIDER RELAY_PROVIDER_RFBRIDGE
// Number of virtual switches
#ifndef DUMMY_RELAY_COUNT
#define DUMMY_RELAY_COUNT 8
#endif
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#define RFB_SUPPORT 1
// When using un-modified harware, ESPurna communicates with the secondary
// MCU EFM8BB1 via UART at 19200 bps so we need to change the speed of
// the port and remove UART noise on serial line
#ifndef RFB_PROVIDER
#define RFB_PROVIDER RFB_PROVIDER_EFM8BB1
#endif
#if RFB_PROVIDER == RFB_PROVIDER_EFM8BB1
#define SERIAL_BAUDRATE 19200
#define DEBUG_SERIAL_SUPPORT 0
#endif
// Only used when RFB_PROVIDER is RCSWITCH
#define RFB_RX_PIN 4
#define RFB_TX_PIN 5
#elif defined(ITEAD_SONOFF_B1)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_B1"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define MY92XX_MODEL MY92XX_MODEL_MY9231
#define MY92XX_CHIPS 2
#define MY92XX_DI_PIN 12
#define MY92XX_DCKI_PIN 14
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 4, 3, 5, 0, 1
#define LIGHT_WHITE_FACTOR (0.1) // White LEDs are way more bright in the B1
#elif defined(ITEAD_SONOFF_LED)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_LED"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 12 // Cold white
#define LIGHT_CH2_PIN 14 // Warm white
#elif defined(ITEAD_SONOFF_T1_1CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_1CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_T1_2CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_2CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON2_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_T1_3CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_3CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON2_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON3_CLICK BUTTON_ACTION_NONE
#define BUTTON3_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON3_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON3_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_S31)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_S31"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Disable UART noise
#define DEBUG_SERIAL_SUPPORT 0
// CSE7766
#define CSE7766_SUPPORT 1
#define CSE7766_RX_PIN 3
#elif defined(ITEAD_SONOFF_S31_LITE)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_S31_LITE"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_IFAN02)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_IFAN02"
// These are virtual buttons triggered by the remote
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON4_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// ORVIBO
// -----------------------------------------------------------------------------
#elif defined(ORVIBO_B25)
// Info
#define MANUFACTURER "ORVIBO"
#define DEVICE "B25"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 12 // 4 blue led
#define LED1_PIN_INVERSE 1
#define LED2_PIN 4 // 12 red led
#define LED2_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// YJZK
// -----------------------------------------------------------------------------
#elif defined(YJZK_SWITCH_1CH)
// Info
#define MANUFACTURER "YJZK"
#define DEVICE "SWITCH_1CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
#elif defined(YJZK_SWITCH_2CH)
// Info
#define MANUFACTURER "YJZK"
#define DEVICE "SWITCH_2CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON2_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
// YJZK 3CH switch
// Also Lixin Touch Wifi 3M
#elif defined(YJZK_SWITCH_3CH)
// Info
#define MANUFACTURER "YJZK"
#define DEVICE "SWITCH_3CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON2_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON3_CLICK BUTTON_ACTION_NONE
#define BUTTON3_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON3_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON3_LNGLNGCLICK BUTTON_ACTION_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Electrodragon boards
// -----------------------------------------------------------------------------
#elif defined(ELECTRODRAGON_WIFI_IOT)
// Info
#define MANUFACTURER "ELECTRODRAGON"
#define DEVICE "WIFI_IOT"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 2
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 16
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// WorkChoice ecoPlug
// -----------------------------------------------------------------------------
#elif defined(WORKCHOICE_ECOPLUG)
// Info
#define MANUFACTURER "WORKCHOICE"
#define DEVICE "ECOPLUG"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// AI Thinker
// -----------------------------------------------------------------------------
#elif defined(AITHINKER_AI_LIGHT)
// Info
#define MANUFACTURER "AITHINKER"
#define DEVICE "AI_LIGHT"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 13
#define MY92XX_DCKI_PIN 15
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// Lyasi LED
// -----------------------------------------------------------------------------
#elif defined(LYASI_LIGHT)
// Info
#define MANUFACTURER "LYASI"
#define DEVICE "RGB_LED"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 4
#define MY92XX_DCKI_PIN 5
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// LED Controller
// -----------------------------------------------------------------------------
#elif defined(MAGICHOME_LED_CONTROLLER)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "LED_CONTROLLER"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE
// IR
#define IR_SUPPORT 1
#define IR_RX_PIN 4
#define IR_BUTTON_SET 1
#elif defined(MAGICHOME_LED_CONTROLLER_20)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "LED_CONTROLLER_20"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE
// IR
#define IR_SUPPORT 1
#define IR_RX_PIN 4
#define IR_BUTTON_SET 1
#elif defined(MAGICHOME_ZJ_WFMN_A_11)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "ZJ_WFMN_A_11"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED2_PIN 15
#define LED2_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE
// IR
#define IR_SUPPORT 1
#define IR_RX_PIN 4
#define IR_BUTTON_SET 1
#elif defined(MAGICHOME_ZJ_WFMN_B_11)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "ZJ_WFMN_B_11"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED2_PIN 15
#define LED2_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE
// RF
#define RFB_SUPPORT 1
#define RFB_PROVIDER RFB_PROVIDER_RCSWITCH
#define RFB_RX_PIN 4
#elif defined(MAGICHOME_ZJ_WFMN_C_11)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "ZJ_WFMN_C_11"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 1
#define LIGHT_CH1_PIN 12 // WHITE
#elif defined(MAGICHOME_ZJ_ESPM_5CH_B_13)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "ZJ_ESPM_5CH_B_13"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 5 // COLD WHITE
#define LIGHT_CH5_PIN 15 // WARM WHITE
#elif defined(MAGICHOME_ZJ_LB_RGBWW_L)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "ZJ_LB_RGBWW_L"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 12 // COLD WHITE
#define LIGHT_CH5_PIN 13 // WARM WHITE
// -----------------------------------------------------------------------------
// HUACANXING H801 & H802
// -----------------------------------------------------------------------------
#elif defined(HUACANXING_H801)
// Info
#define MANUFACTURER "HUACANXING"
#define DEVICE "H801"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define DEBUG_PORT Serial1
#define SERIAL_RX_ENABLED 1
// LEDs
#define LED1_PIN 5
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 15 // RED
#define LIGHT_CH2_PIN 13 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE1
#define LIGHT_CH5_PIN 4 // WHITE2
#elif defined(HUACANXING_H802)
// Info
#define MANUFACTURER "HUACANXING"
#define DEVICE "H802"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define DEBUG_PORT Serial1
#define SERIAL_RX_ENABLED 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 14 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE
// -----------------------------------------------------------------------------
// HUGOAI AWP02L-N
// Pin equivalence extracted from https://templates.blakadder.com/hugoai_awp02l-n.html
//
// It follows almost same structure as AOYCOCR X5P with only 1 LED on GPIO02
//
// -----------------------------------------------------------------------------
#elif defined(HUGOAI_AWP02L_N)
#define MANUFACTURER "HUGOAI"
#define DEVICE "AWP02L_N"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// the defaults are reasonable, but you can change them as desired
//#define BUTTON1_PRESS BUTTON_ACTION_NONE
//#define BUTTON1_CLICK BUTTON_ACTION_TOGGLE
//#define BUTTON1_DBLCLICK BUTTON_ACTION_AP
//#define BUTTON1_LNGCLICK BUTTON_ACTION_RESET
//#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_FACTORY
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
// LED1 (blue) indicates on/off state; you could use LED_MODE_FOLLOW_INVERSE
// so that the LED lights the button when 'off' so it can be found easily.
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_FOLLOW
#define LED1_RELAY 1
// -----------------------------------------------------------------------------
// Jan Goedeke Wifi Relay
// https://github.com/JanGoe/esp8266-wifi-relay
// -----------------------------------------------------------------------------
#elif defined(JANGOE_WIFI_RELAY_NC)
// Info
#define MANUFACTURER "JANGOE"
#define DEVICE "WIFI_RELAY_NC"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON2_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 2
#define RELAY2_PIN 14
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_TYPE RELAY_TYPE_INVERSE
#elif defined(JANGOE_WIFI_RELAY_NO)
// Info
#define MANUFACTURER "JANGOE"
#define DEVICE "WIFI_RELAY_NO"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON2_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 2
#define RELAY2_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// Jorge García Wifi+Relays Board Kit
// https://www.tindie.com/products/jorgegarciadev/wifi--relays-board-kit
// https://github.com/jorgegarciadev/wifikit
// -----------------------------------------------------------------------------
#elif defined(JORGEGARCIA_WIFI_RELAYS)
// Info
#define MANUFACTURER "JORGEGARCIA"
#define DEVICE "WIFI_RELAYS"
// Relays
#define RELAY1_PIN 0
#define RELAY2_PIN 2
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_TYPE RELAY_TYPE_INVERSE
// -----------------------------------------------------------------------------
// WiFi MQTT Relay / Thermostat
// -----------------------------------------------------------------------------
#elif defined(OPENENERGYMONITOR_MQTT_RELAY)
// Info
#define MANUFACTURER "OPENENERGYMONITOR"
#define DEVICE "MQTT_RELAY"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 16
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// WiOn 50055 Indoor Wi-Fi Wall Outlet & Tap
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50050-Indoor-Wi-Fi-Outlet-Wireless-Switch-Programmable-Timer-%2F263112281551
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50055-Indoor-Wi-Fi-Wall-Tap-Monitor-Energy-Usage-Wireless-Smart-Switch-%2F263020837777
// -----------------------------------------------------------------------------
#elif defined(WION_50055)
// Currently untested, does not support energy monitoring
// Info
#define MANUFACTURER "WION"
#define DEVICE "50055"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// EX-Store Wifi Relay v3.1
// https://ex-store.de/ESP8266-WiFi-Relay-V31
// -----------------------------------------------------------------------------
#elif defined(EXS_WIFI_RELAY_V31)
// Untested
// Info
#define MANUFACTURER "EXS"
#define DEVICE "WIFI_RELAY_V31"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 13
#define RELAY1_TYPE RELAY_TYPE_LATCHED
#define RELAY1_RESET_PIN 12
// -----------------------------------------------------------------------------
// EX-Store Wifi Relay v5.0
// -----------------------------------------------------------------------------
#elif defined(EXS_WIFI_RELAY_V50)
// Info
#define MANUFACTURER "EXS"
#define DEVICE "WIFI_RELAY_V50"
// Buttons
#define BUTTON1_PIN 5
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT | BUTTON_SET_PULLUP
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_RELEASE BUTTON_ACTION_TOGGLE
#define BUTTON2_PIN 4
#define BUTTON2_RELAY 2
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT | BUTTON_SET_PULLUP
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_RELEASE BUTTON_ACTION_TOGGLE
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_LATCHED
#define RELAY1_RESET_PIN 16
#define RELAY2_PIN 13
#define RELAY2_TYPE RELAY_TYPE_LATCHED
#define RELAY2_RESET_PIN 12
// LEDs
#define LED1_PIN 15
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// V9261F
// -----------------------------------------------------------------------------
#elif defined(GENERIC_V9261F)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "V9261F"
#define ALEXA_SUPPORT 0
// V9261F
#define V9261F_SUPPORT 1
#define V9261F_PIN 2
#define V9261F_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// ECH1560
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ECH1560)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ECH1560"
#define ALEXA_SUPPORT 0
// ECH1560
#define ECH1560_SUPPORT 1
#define ECH1560_CLK_PIN 4
#define ECH1560_MISO_PIN 5
#define ECH1560_INVERTED 0
// -----------------------------------------------------------------------------
// PZEM004T
// -----------------------------------------------------------------------------
#elif defined(GENERIC_PZEM004T)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "PZEM004T"
#define PZEM004T_SUPPORT 1
#define ALEXA_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// ESP-01 generic esp8266 board with 512 kB flash
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ESP01_512KB)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ESP01_512KB"
// Relays
#define RELAY1_PIN 2
#ifndef RELAY1_TYPE
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#endif
// No need for OTA
#define OTA_WEB_SUPPORT 0
#define OTA_ARDUINOOTA_SUPPORT 0
#define OTA_CLIENT OTA_CLIENT_NONE
// Web UI blob & MDNS are pretty large
#define WEB_EMBEDDED 0
#define MDNS_SERVER_SUPPORT 0
// -----------------------------------------------------------------------------
// ESPLive
// https://github.com/ManCaveMade/ESP-Live
// -----------------------------------------------------------------------------
#elif defined(MANCAVEMADE_ESPLIVE)
// Info
#define MANUFACTURER "MANCAVEMADE"
#define DEVICE "ESPLIVE"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON2_PIN 5
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// DS18B20
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 2
#define DALLAS_UPDATE_INTERVAL 5000
#define TEMPERATURE_MIN_CHANGE 1.0
// -----------------------------------------------------------------------------
// QuinLED
// http://blog.quindorian.org/2017/02/esp8266-led-lighting-quinled-v2-6-pcb.html
// -----------------------------------------------------------------------------
#elif defined(INTERMITTECH_QUINLED)
// Info
#define MANUFACTURER "INTERMITTECH"
#define DEVICE "QUINLED"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 5
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 0
#define LIGHT_CH2_PIN 2
// -----------------------------------------------------------------------------
// Arilux AL-LC06
// -----------------------------------------------------------------------------
#elif defined(ARILUX_AL_LC01)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC01"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#elif defined(ARILUX_AL_LC02)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC02"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE1
#elif defined(ARILUX_AL_LC02_V14)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC02_V14"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE1
#elif defined(ARILUX_AL_LC06)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC06"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE1
#define LIGHT_CH5_PIN 5 // WHITE2
#elif defined(ARILUX_AL_LC11)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC11"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE1
#define LIGHT_CH5_PIN 12 // WHITE1
#elif defined(ARILUX_E27)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "E27"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 13
#define MY92XX_DCKI_PIN 15
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// XENON SM-PW701U
// -----------------------------------------------------------------------------
#elif defined(XENON_SM_PW702U)
// Info
#define MANUFACTURER "XENON"
#define DEVICE "SM_PW702U"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// ISELECTOR SM-PW702
// -----------------------------------------------------------------------------
#elif defined(ISELECTOR_SM_PW702)
// Info
#define MANUFACTURER "ISELECTOR"
#define DEVICE "SM_PW702"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4 //BLUE
#define LED1_PIN_INVERSE 0
#define LED2_PIN 5 //RED
#define LED2_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// AUTHOMETION LYT8266
// https://authometion.com/shop/en/home/13-lyt8266.html
// -----------------------------------------------------------------------------
#elif defined(AUTHOMETION_LYT8266)
// Info
#define MANUFACTURER "AUTHOMETION"
#define DEVICE "LYT8266"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 13 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 2 // WHITE
#define LIGHT_ENABLE_PIN 15
#elif defined(GIZWITS_WITTY_CLOUD)
// Info
#define MANUFACTURER "GIZWITS"
#define DEVICE "WITTY_CLOUD"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
#define ANALOG_SUPPORT 1
// LEDs
#define LED1_PIN 2 // BLUE build-in
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 15 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
// -----------------------------------------------------------------------------
// KMC 70011
// https://www.amazon.com/KMC-Monitoring-Required-Control-Compatible/dp/B07313TH7B
// -----------------------------------------------------------------------------
#elif defined(KMC_70011)
// Info
#define MANUFACTURER "KMC"
#define DEVICE "70011"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor
// -----------------------------------------------------------------------------
// Euromate (?) Wifi Stecker Schuko
// https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko/p/2291706
// Thanks to @Geitde
// -----------------------------------------------------------------------------
#elif defined(EUROMATE_WIFI_STECKER_SCHUKO)
// Info
#define MANUFACTURER "EUROMATE"
#define DEVICE "WIFI_STECKER_SCHUKO"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// The relay in the device is not a bistable (latched) relay.
// The device is reported to have a flip-flop circuit to drive the relay
// So @Geitde hack is still the only possible
// Hack: drive GPIO12 low and use GPIO5 as normal relay pin:
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define LED2_PIN 12 /* DUMMY: exploit default off state for GPIO12=low */
#define LED2_PIN_INVERSE 0
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Euromate (?) Wifi Stecker Schuko Version 2
// This configuration is for the second generation of devices sold by OBI.
// https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko-weiss/p/4077806
// -----------------------------------------------------------------------------
#elif defined(EUROMATE_WIFI_STECKER_SCHUKO_V2)
// Info
#define MANUFACTURER "EUROMATE"
#define DEVICE "WIFI_STECKER_SCHUKO_V2"
// Buttons
#define BUTTON1_PIN 5
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// Green
#define LED1_PIN 12
#define LED1_MODE LED_MODE_WIFI
#define LED1_PIN_INVERSE 0
// Red
#define LED2_PIN 13
#define LED2_MODE LED_MODE_RELAY
#define LED2_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Generic 8CH
// -----------------------------------------------------------------------------
#elif defined(GENERIC_8CH)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "8CH"
// Relays
#define RELAY1_PIN 0
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 2
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_PIN 4
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_PIN 5
#define RELAY4_TYPE RELAY_TYPE_NORMAL
#define RELAY5_PIN 12
#define RELAY5_TYPE RELAY_TYPE_NORMAL
#define RELAY6_PIN 13
#define RELAY6_TYPE RELAY_TYPE_NORMAL
#define RELAY7_PIN 14
#define RELAY7_TYPE RELAY_TYPE_NORMAL
#define RELAY8_PIN 15
#define RELAY8_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// STM RELAY
// -----------------------------------------------------------------------------
#elif defined(STM_RELAY)
// Info
#define MANUFACTURER "STM_RELAY"
#define DEVICE "2CH"
// Relays
#define DUMMY_RELAY_COUNT 2
#define RELAY_PROVIDER RELAY_PROVIDER_STM
// Remove UART noise on serial line
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// Tonbux Powerstrip02
// -----------------------------------------------------------------------------
#elif defined(TONBUX_POWERSTRIP02)
// Info
#define MANUFACTURER "TONBUX"
#define DEVICE "POWERSTRIP02"
// Buttons
#define BUTTON1_PIN 5
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 0
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_PIN 13
#define RELAY2_TYPE RELAY_TYPE_INVERSE
#define RELAY3_PIN 12
#define RELAY3_TYPE RELAY_TYPE_INVERSE
#define RELAY4_PIN 14
#define RELAY4_TYPE RELAY_TYPE_INVERSE
// Not a relay. USB ports on/off
#define RELAY5_PIN 16
#define RELAY5_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // 1 blue led
#define LED1_PIN_INVERSE 1
#define LED2_PIN 3 // 3 red leds
#define LED2_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Lingan SWA1
// -----------------------------------------------------------------------------
#elif defined(LINGAN_SWA1)
// Info
#define MANUFACTURER "LINGAN"
#define DEVICE "SWA1"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// HEYGO HY02
// -----------------------------------------------------------------------------
#elif defined(HEYGO_HY02)
// Info
#define MANUFACTURER "HEYGO"
#define DEVICE "HY02"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Maxcio W-US002S
// -----------------------------------------------------------------------------
#elif defined(MAXCIO_WUS002S)
// Info
#define MANUFACTURER "MAXCIO"
#define DEVICE "WUS002S"
// Buttons
#define BUTTON1_PIN 2
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 3
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_CURRENT_R 0.002 // Current resistor
#define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor
// LED1 on RX pin
#define DEBUG_SERIAL_SUPPORT 1
// -----------------------------------------------------------------------------
// Maxcio W-DE004
// -----------------------------------------------------------------------------
#elif defined(MAXCIO_WDE004)
// Info
#define MANUFACTURER "MAXCIO"
#define DEVICE "WDE004"
// Buttons
#define BUTTON1_PIN 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Maxcio W-UK007S
// Like this: https://www.amazon.co.uk/Maxcio-Monitoring-Function-Compatible-Required/dp/B07BWFB55Q/ref=pd_rhf_se_p_img_2?_encoding=UTF8&psc=1&refRID=4H63A43SKHV8WV54XH19
// -----------------------------------------------------------------------------
#elif defined(MAXCIO_WUK007S)
// Info
#define MANUFACTURER "MAXCIO"
#define DEVICE "WUK007S"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0
#define LED1_PIN_INVERSE 0
#define LED1_RELAY 1
#define LED1_MODE LED_MODE_RELAY_WIFI
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 24380
#define HLW8012_VOLTAGE_RATIO 32048
#define HLW8012_POWER_RATIO 3509285
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// Oukitel P1 Smart Plug
// https://www.amazon.com/Docooler-OUKITEL-Control-Wireless-Adaptor/dp/B07J3BYFJX/ref=sr_1_fkmrnull_2?keywords=oukitel+p1+smart+switch&qid=1550424399&s=gateway&sr=8-2-fkmrnull
// -----------------------------------------------------------------------------
#elif defined(OUKITEL_P1)
// Info
#define MANUFACTURER "Oukitel"
#define DEVICE "P1"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
// Right
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// Left
#define RELAY2_PIN 15
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // blue
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_WIFI
// -----------------------------------------------------------------------------
// YiDian XS-SSA05
// -----------------------------------------------------------------------------
#elif defined(YIDIAN_XSSSA05)
// Info
#define MANUFACTURER "YIDIAN"
#define DEVICE "XSSSA05"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // red
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_WIFI
#define LED2_PIN 15 // blue
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_RELAY
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 3
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// TONBUX XS-SSA01
// -----------------------------------------------------------------------------
#elif defined(TONBUX_XSSSA01)
// Info
#define MANUFACTURER "TONBUX"
#define DEVICE "XSSSA01"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// TONBUX XS-SSA06
// -----------------------------------------------------------------------------
#elif defined(TONBUX_XSSSA06)
// Info
#define MANUFACTURER "TONBUX"
#define DEVICE "XSSSA06"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // R - 8 rgb led ring
#define LED1_PIN_INVERSE 0
#define LED2_PIN 5 // G
#define LED2_PIN_INVERSE 0
#define LED3_PIN 2 // B
#define LED3_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// GREEN ESP8266 RELAY MODULE
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180323113846&SearchText=Green+ESP8266
// -----------------------------------------------------------------------------
#elif defined(GREEN_ESP8266RELAY)
// Info
#define MANUFACTURER "GREEN"
#define DEVICE "ESP8266RELAY"
// Buttons
// Not a button but input via Optocoupler
#define BUTTON1_PIN 5
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Henrique Gravina ESPIKE
// https://github.com/Henriquegravina/Espike
// -----------------------------------------------------------------------------
#elif defined(IKE_ESPIKE)
#define MANUFACTURER "IKE"
#define DEVICE "ESPIKE"
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_PIN 13
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PIN 12
#define BUTTON2_RELAY 2
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_PIN 14
#define BUTTON3_RELAY 3
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 5
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_PIN 16
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// SWIFITCH
// https://github.com/ArnieX/swifitch
// -----------------------------------------------------------------------------
#elif defined(ARNIEX_SWIFITCH)
// Info
#define MANUFACTURER "ARNIEX"
#define DEVICE "SWIFITCH"
// Buttons
#define BUTTON1_PIN 4 // D2
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_BOOT
#define BUTTON1_RELAY 1
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_RELEASE BUTTON_ACTION_TOGGLE
// Relays
#define RELAY1_PIN 5 // D1
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// LEDs
#define LED1_PIN 12 // D6
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// ESP-01S RELAY v4.0
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404024035&SearchText=esp-01s+relay
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ESP01S_RELAY_V40)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ESP01S_RELAY_40"
// Relays
#define RELAY1_PIN 0
#ifndef RELAY1_TYPE
#define RELAY1_TYPE RELAY_TYPE_NORMAL // See #1504 and #1554
#endif
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// ESP-01S RGB LED v1.0 (some sold with ws2818)
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404023816&SearchText=esp-01s+led+controller
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ESP01S_RGBLED_V10)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ESP01S_RGBLED_10"
// This board is sold as RGB LED module BUT it has on board 3 pin ph2.0 connector (VCC, GPIO2, GND)
// so, if you wish, you may connect LED, BUTTON, RELAY, SENSOR etc.
// Buttons
//#define BUTTON1_PIN 2
// Relays
//#define RELAY1_PIN 2
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// ESP-01S DHT11 v1.0
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180410105907&SearchText=esp-01s+dht11
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ESP01S_DHT11_V10)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ESP01S_DHT11_10"
// DHT11
#ifndef DHT_SUPPORT
#define DHT_SUPPORT 1
#endif
#define DHT_PIN 2
#define DHT_TYPE DHT_CHIP_DHT11
// -----------------------------------------------------------------------------
// ESP-01S DS18B20 v1.0
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180410105933&SearchText=esp-01s+ds18b20
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ESP01S_DS18B20_V10)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ESP01S_DS18B20_10"
// DB18B20
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 2
// -----------------------------------------------------------------------------
// ESP-DIN relay board V1
// https://github.com/pilotak/esp_din
// -----------------------------------------------------------------------------
#elif defined(PILOTAK_ESP_DIN_V1)
// Info
#define MANUFACTURER "PILOTAK"
#define DEVICE "ESP_DIN_V1"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 5
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 15
#define LED1_PIN_INVERSE 0
#define I2C_SDA_PIN 12
#define I2C_SCL_PIN 13
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 2
#define RFB_SUPPORT 1
#define RFB_PROVIDER RFB_PROVIDER_RCSWITCH
#define RFB_RX_PIN 14
#ifndef DIGITAL_SUPPORT
#define DIGITAL_SUPPORT 1
#endif
#define DIGITAL1_PIN 16
#define DIGITAL1_PIN_MODE INPUT
#define DIGITAL1_DEFAULT_STATE 0
// -----------------------------------------------------------------------------
// Heltec Touch Relay
// https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180408043114&SearchText=esp8266+touch+relay
// -----------------------------------------------------------------------------
#elif defined(HELTEC_TOUCHRELAY)
// Info
#define MANUFACTURER "HELTEC"
#define DEVICE "TOUCH_RELAY"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// Zhilde ZLD-44EU-W
// http://www.zhilde.com/product/60705150109-805652505/EU_WiFi_Surge_Protector_Extension_Socket_4_Outlets_works_with_Amazon_Echo_Smart_Power_Strip.html
// -----------------------------------------------------------------------------
#elif defined(ZHILDE_44EU_W)
// Info
#define MANUFACTURER "ZHILDE"
#define DEVICE "44EU_W"
// Based on the reporter, this product uses GPIO1 and 3 for the button
// and onboard LED, so hardware serial should be disabled...
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON1_PIN 3
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 5
#define RELAY2_PIN 4
#define RELAY3_PIN 12
#define RELAY4_PIN 13
#define RELAY5_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
#define RELAY5_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 1
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Zhilde ZLD-64EU-W
// -----------------------------------------------------------------------------
#elif defined(ZHILDE_64EU_W)
// Info
#define MANUFACTURER "ZHILDE"
#define DEVICE "64EU_W"
// Based on https://templates.blakadder.com/ZLD64-EU-W.html ,
// This product uses GPIO1 for LED and 3 for the button, so hardware serial should be disabled...
#define DEBUG_SERIAL_SUPPORT 0
#define BUTTON1_PIN 3
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_NONE
#define BUTTON1_RELAY 3
#define RELAY1_PIN 5
#define RELAY2_PIN 4
#define RELAY3_PIN 14
#define LED1_PIN 1
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Allnet 4duino ESP8266-UP-Relais
// http://www.allnet.de/de/allnet-brand/produkte/neuheiten/p/allnet-4duino-iot-wlan-relais-unterputz-esp8266-up-relais/
// https://shop.allnet.de/fileadmin/transfer/products/148814.pdf
// -----------------------------------------------------------------------------
#elif defined(ALLNET_4DUINO_IOT_WLAN_RELAIS)
// Info
#define MANUFACTURER "ALLNET"
#define DEVICE "4DUINO_IOT_WLAN_RELAIS"
// Relays
#define RELAY1_PIN 14
#define RELAY1_RESET_PIN 12
#define RELAY1_TYPE RELAY_TYPE_LATCHED
// LEDs
#define LED1_PIN 0
#define LED1_PIN_INVERSE 1
// Buttons
//#define BUTTON1_PIN 0
//#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Using pins labelled as SDA & SCL as buttons
#define BUTTON2_PIN 4
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON2_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_NONE
#define BUTTON3_PIN 5
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON
// Using pins labelled as SDA & SCL for I2C
//#define I2C_SDA_PIN 4
//#define I2C_SCL_PIN 5
// -----------------------------------------------------------------------------
// Luani HVIO
// https://luani.de/projekte/esp8266-hvio/
// https://luani.de/blog/esp8266-230v-io-modul/
// -----------------------------------------------------------------------------
#elif defined(LUANI_HVIO)
// Info
#define MANUFACTURER "LUANI"
#define DEVICE "HVIO"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT //Hardware Pullup
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_RELEASE BUTTON_ACTION_TOGGLE
#define BUTTON2_PIN 13
#define BUTTON2_RELAY 2
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT //Hardware Pullup
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_RELEASE BUTTON_ACTION_TOGGLE
// Relays
#define RELAY1_PIN 4
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 15
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Tonbux 50-100M Smart Mosquito Killer USB
// https://www.aliexpress.com/item/Original-Tonbux-50-100M-Smart-Mosquito-Killer-USB-Plug-No-Noise-Repellent-App-Smart-Module/32859330820.html
// -----------------------------------------------------------------------------
#elif defined(TONBUX_MOSQUITO_KILLER)
// Info
#define MANUFACTURER "TONBUX"
#define DEVICE "MOSQUITO_KILLER"
// Buttons
#define BUTTON1_PIN 2
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 5 // not a relay, fan
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 15 // blue led
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_WIFI
#define LED2_PIN 14 // red led
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_RELAY
#define LED3_PIN 12 // UV leds (1-2-3-4-5-6-7-8)
#define LED3_PIN_INVERSE 0
#define LED3_RELAY 1
#define LED4_PIN 16 // UV leds (9-10-11)
#define LED4_PIN_INVERSE 0
#define LED4_RELAY 1
// -----------------------------------------------------------------------------
// Avatto NAS-WR01W Wifi Smart Power Plug
// https://www.aliexpress.com/item/33011753732.html
// https://todo...
// -----------------------------------------------------------------------------
#elif defined(AVATTO_NAS_WR01W)
// Info
#define MANUFACTURER "AVATTO"
#define DEVICE "NAS_WR01W"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// NEO Coolcam NAS-WR01W Wifi Smart Power Plug
// https://es.aliexpress.com/item/-/32854589733.html?spm=a219c.12010608.0.0.6d084e68xX0y5N
// https://www.fasttech.com/product/9649426-neo-coolcam-nas-wr01w-wifi-smart-power-plug-eu
// -----------------------------------------------------------------------------
#elif defined(NEO_COOLCAM_NAS_WR01W)
// Info
#define MANUFACTURER "NEO_COOLCAM"
#define DEVICE "NAS_WR01W"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Deltaco SH_P01 Wifi Smart Power Plug
// -----------------------------------------------------------------------------
#elif defined(DELTACO_SH_P01)
// Info
#define MANUFACTURER "DELTACO"
#define DEVICE "SH_P01"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 5
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_FINDME
// ------------------------------------------------------------------------------
// DELTACO_SH_P03USB Wifi Smart Power Plug
// -----------------------------------------------------------------------------
#elif defined(DELTACO_SH_P03USB)
// Info
#define MANUFACTURER "DELTACO"
#define DEVICE "SH_P03USB"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP
#define BUTTON1_RELAY 2
// Relays
#define RELAY1_PIN 15 // USB power
#define RELAY2_PIN 12 // power plug 1
#define RELAY3_PIN 14 // power plug 2
#define RELAY4_PIN 5 // power plug 3
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // power led
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_FINDME
// ------------------------------------------------------------------------------
// Fornorm Wi-Fi USB Extension Socket (ZLD-34EU)
// https://www.aliexpress.com/item/Fornorm-WiFi-Extension-Socket-with-Surge-Protector-Smart-Power-Strip-3-Outlets-and-4-USB-Charging/32849743948.html
// Also: Estink Wifi Power Strip
// -----------------------------------------------------------------------------
#elif defined(FORNORM_ZLD_34EU)
// Info
#define MANUFACTURER "FORNORM"
#define DEVICE "ZLD_34EU"
// Disable UART noise since this board uses GPIO3
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON1_PIN 16
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 4
// Relays
#define RELAY1_PIN 14 // USB power
#define RELAY2_PIN 13 // power plug 1
#define RELAY3_PIN 4 // power plug 2
#define RELAY4_PIN 15 // power plug 3
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // power led
#define LED2_PIN 12 // power plug 1
#define LED3_PIN 3 // power plug 2
#define LED4_PIN 5 // power plug 3
#define LED1_PIN_INVERSE 1
#define LED2_PIN_INVERSE 1
#define LED3_PIN_INVERSE 1
#define LED4_PIN_INVERSE 1
#define LED1_MODE LED_MODE_FINDME
#define LED2_MODE LED_MODE_FOLLOW
#define LED3_MODE LED_MODE_FOLLOW
#define LED4_MODE LED_MODE_FOLLOW
#define LED2_RELAY 2
#define LED3_RELAY 3
#define LED4_RELAY 4
// -----------------------------------------------------------------------------
// Bruno Horta's OnOfre
// https://www.bhonofre.pt/
// https://github.com/brunohorta82/BH_OnOfre/
// -----------------------------------------------------------------------------
#elif defined(BH_ONOFRE)
// Info
#define MANUFACTURER "BH"
#define DEVICE "ONOFRE"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 13
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 5
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// BlitzWolf SHP2 and SHP6
// Also several boards under different names uing a power chip labelled BL0937 or HJL-01
// * Blitzwolf (https://www.amazon.es/Inteligente-Temporización-Dispositivos-Cualquier-BlitzWolf/dp/B07BMQP142)
// * HomeCube (https://www.amazon.de/Steckdose-Homecube-intelligente-Verbrauchsanzeige-funktioniert/dp/B076Q2LKHG)
// * Coosa (https://www.amazon.com/COOSA-Monitoring-Function-Campatible-Assiatant/dp/B0788W9TDR)
// * Gosund (http://www.gosund.com/?m=content&c=index&a=show&catid=6&id=5)
// * Ablue (https://www.amazon.de/Intelligente-Steckdose-Ablue-Funktioniert-Assistant/dp/B076DRFRZC)
// * DIY Tech Smart Home (https://www.amazon.es/gp/product/B07HHKXYS9)
// -----------------------------------------------------------------------------
#elif defined(BLITZWOLF_BWSHPX)
// Info
#define MANUFACTURER "BLITZWOLF"
#define DEVICE "BWSHPX"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED2_PIN 0
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 1
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// Same as the above but new board version marked V2.3
// BlitzWolf SHP2 V2.3
// Gosund SP1 V2.3
// -----------------------------------------------------------------------------
#elif defined(BLITZWOLF_BWSHPX_V23)
// Info
#define MANUFACTURER "BLITZWOLF"
#define DEVICE "BWSHPX_V23"
// Buttons
#define BUTTON1_PIN 3
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 1
#define LED1_PIN_INVERSE 1
#define LED2_PIN 13
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 1
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// BUTTON1 and LED1 are using Serial pins
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// Similar to both devices above but also with switchable USB ports
// and other sensor (CSE7766).
// the pin layout is different to the above two versions
// BlitzWolf SHP5
// -----------------------------------------------------------------------------
#elif defined(BLITZWOLF_BWSHP5)
// Info
#define MANUFACTURER "BLITZWOLF"
#define DEVICE "BWSHP5"
// Buttons
#define BUTTON1_PIN 16
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
// Power plug
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// USB
#define RELAY2_PIN 5
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED2_PIN 0
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 1
// Disable UART noise
#define DEBUG_SERIAL_SUPPORT 0
// CSE7766
#ifndef CSE7766_SUPPORT
#define CSE7766_SUPPORT 1
#endif
#define CSE7766_RX_PIN 3
// -----------------------------------------------------------------------------
// Teckin SP21
// -----------------------------------------------------------------------------
#elif defined(TECKIN_SP21)
// Info
#define MANUFACTURER "TECKIN"
#define DEVICE "SP21"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Teckin SP22 v1.4 - v1.6
// -----------------------------------------------------------------------------
#elif defined(TECKIN_SP22_V14)
// Info
#define MANUFACTURER "TECKIN"
#define DEVICE "SP22_V14"
// Buttons
#define BUTTON1_PIN 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 3
#define LED1_PIN_INVERSE 1
#define LED2_PIN 13
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 1
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 20730
#define HLW8012_VOLTAGE_RATIO 264935
#define HLW8012_POWER_RATIO 2533110
#define HLW8012_INTERRUPT_ON FALLING
// BUTTON1 and LED1 are using Serial pins
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// Teckin SP22 v1.4 - v1.6
//
// NB Notes suggest that energy monitoring is removed from later versions
// -----------------------------------------------------------------------------
#elif defined(TECKIN_SP23_V13)
// Info .. NB Newer versions apparently lack energy monitor
// The board revision is not indicated externally
#define MANUFACTURER "TECKIN"
#define DEVICE "SP23_V13"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
#define LED2_PIN 2
#define LED2_PIN_INVERSE 0
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 1
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 23324
#define HLW8012_VOLTAGE_RATIO 324305
#define HLW8012_POWER_RATIO 3580841
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// The Gosund WP3 is based on ESP8285, so 1 MB internal flash (DOUT required)
// The module has no-connect: TX, RX, RST, AD, GPIO5, (and GPIO0,
// GPIO2 via test points on the back of the module)
// and these are wired to devices:
// GPIO4: /BTN
// GPIO12: /LED red
// GPIO13: /LED blue
// GPIO14: RELAY
// -----------------------------------------------------------------------------
#elif defined(GOSUND_WP3)
// Info
#define MANUFACTURER "GOSUND"
#define DEVICE "WP3"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// the defaults are reasonable, but you can change them as desired
//#define BUTTON1_PRESS BUTTON_ACTION_NONE
//#define BUTTON1_CLICK BUTTON_ACTION_TOGGLE
//#define BUTTON1_DBLCLICK BUTTON_ACTION_AP
//#define BUTTON1_LNGCLICK BUTTON_ACTION_RESET
//#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_FACTORY
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
// LED1 (red) indicates on/off state; you could use LED_MODE_FOLLOW_INVERSE
// so that the LED lights the button when 'off' so it can be found easily.
#define LED1_PIN 12
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_FOLLOW
#define LED1_RELAY 1
// LED2 (blue) indicates wifi activity
#define LED2_PIN 13
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_WIFI
// -----------------------------------------------------------------------------
// Several boards under different names uing a power chip labelled BL0937 or HJL-01
// Also model number KS-602S
// -----------------------------------------------------------------------------
#elif defined(GOSUND_WS1)
// Info
#define MANUFACTURER "GOSUND"
#define DEVICE "WS1"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 1
#define LED1_PIN_INVERSE 1
// LED1 is using TX pin
#define DEBUG_SERIAL_SUPPORT 0
// ----------------------------------------------------------------------------------------
// Power socket 16A similar to BLITZWOLF_BWSHPX but button pin differs
// IMPORTANT, This template is for hardware version SP111_A_Wifi_Ver1.1 (as printed on the PCB)
// hhttps://www.amazon.de/-/en/Smallest-Consumption-Measuring-Function-Compatible/dp/B07PSMF47W
// ----------------------------------------------------------------------------------------
#elif defined(GOSUND_SP111)
// Info
#define MANUFACTURER "GOSUND"
#define DEVICE "SP111"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED2_PIN 0
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 1
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 4
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// ----------------------------------------------------------------------------------------
// Power strip 15A - 3 Sockets + 3 USB ports
// This device uses just one digital button (main one). All other three buttons are connected
// to the ADC pin via resistors with different values. This approach is known under the name of
// "Resistor Ladder" - https://en.wikipedia.org/wiki/Resistor_ladder
// https://www.amazon.de/-/en/gp/product/B085XXCPRD
// ----------------------------------------------------------------------------------------
#elif defined(GOSUND_P1)
// Info
#define MANUFACTURER "GOSUND"
#define DEVICE "P1"
//Enable this to view buttons analog level.
//#define ANALOG_SUPPORT 1
// Disable UART noise
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON_PROVIDER_ANALOG_SUPPORT 1
#define BUTTON1_PIN 16
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 4
#define BUTTON2_PIN 17
#define BUTTON2_RELAY 3
#define BUTTON2_PROVIDER BUTTON_PROVIDER_ANALOG
#define BUTTON2_ANALOG_LEVEL 220
#define BUTTON3_PIN 17
#define BUTTON3_RELAY 2
#define BUTTON3_PROVIDER BUTTON_PROVIDER_ANALOG
#define BUTTON3_ANALOG_LEVEL 470
#define BUTTON4_PIN 17
#define BUTTON4_RELAY 1
#define BUTTON4_PROVIDER BUTTON_PROVIDER_ANALOG
#define BUTTON4_ANALOG_LEVEL 730
// Relays
#define RELAY1_PIN 14
#define RELAY2_PIN 12
#define RELAY3_PIN 13
#define RELAY4_PIN 5
#define RELAY4_TYPE RELAY_TYPE_INVERSE
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// CSE7766
#define CSE7766_SUPPORT 1
#define CSE7766_RX_PIN 3
// ----------------------------------------------------------------------------------------
// Homecube 16A is similar but some pins differ and it also has RGB LEDs
// https://www.amazon.de/gp/product/B07D7RVF56/ref=oh_aui_detailpage_o00_s01?ie=UTF8&psc=1
// ----------------------------------------------------------------------------------------
#elif defined(HOMECUBE_16A)
// Info
#define MANUFACTURER "HOMECUBE"
#define DEVICE "16A"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
//LED Pin 4 - ESP8266 onboard LED
//Red LED: 0
//Green LED: 12
//Blue LED: 2
// Blue
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// Green
#define LED2_PIN 12
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_RELAY
// Red
#define LED3_PIN 0
#define LED3_PIN_INVERSE 0
#define LED3_MODE LED_MODE_OFF
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 16
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// VANZAVANZU Smart Outlet Socket (based on BL0937 or HJL-01)
// https://www.amazon.com/Smart-Plug-Wifi-Mini-VANZAVANZU/dp/B078PHD6S5
// -----------------------------------------------------------------------------
#elif defined(VANZAVANZU_SMART_WIFI_PLUG_MINI)
// Info
#define MANUFACTURER "VANZAVANZU"
#define DEVICE "SMART_WIFI_PLUG_MINI"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED2_PIN 0
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 1
// Disable UART noise
#define DEBUG_SERIAL_SUPPORT 0
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 3
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
#elif defined(GENERIC_AG_L4)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "AG_L4"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// button 1: "power" button
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
// button 2: "wifi" button
#define BUTTON2_PIN 2
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON2_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_NONE
// LEDs
#define LED1_PIN 5 // red status led
#define LED1_PIN_INVERSE 0
#define LED2_PIN 16 // master light power
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_RELAY
// Light
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 13 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
// -----------------------------------------------------------------------------
#elif defined(GENERIC_AG_L4_V3)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "AG_L4_V3"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// button 1: "power" button
#define BUTTON1_PIN 13
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_CLICK BUTTON_ACTION_NONE
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET
// button 2: "wifi" button
#define BUTTON2_PIN 2
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_CLICK BUTTON_ACTION_NONE
#define BUTTON2_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_NONE
// LEDs
#define LED1_PIN 5 // red status led
#define LED1_PIN_INVERSE 0
#define LED2_PIN 16 // master light power
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_RELAY
// Light
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 4 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
// -----------------------------------------------------------------------------
#elif defined(ALLTERCO_SHELLY1)
// Info
#define MANUFACTURER "ALLTERCO"
#define DEVICE "SHELLY1"
// Buttons
#define BUTTON1_PIN 5
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT
#define BUTTON1_RELAY 1
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_RELEASE BUTTON_ACTION_TOGGLE
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#elif defined(ALLTERCO_SHELLY2)
// Info
#define MANUFACTURER "ALLTERCO"
#define DEVICE "SHELLY2"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON1_RELAY 1
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_RELEASE BUTTON_ACTION_TOGGLE
#define BUTTON2_PIN 14
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT
#define BUTTON2_RELAY 2
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_RELEASE BUTTON_ACTION_TOGGLE
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 5
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#elif defined(ALLTERCO_SHELLY1PM)
// Info
#define MANUFACTURER "ALLTERCO"
#define DEVICE "SHELLY1PM"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT
#define BUTTON1_RELAY 1
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_RELEASE BUTTON_ACTION_TOGGLE
#define BUTTON2_PIN 2
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_LNGCLICK BUTTON_ACTION_RESET
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_FACTORY
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// Light
#define LED1_PIN 0
#define LED1_PIN_INVERSE 1
// HJL01 / BL0937
#define HLW8012_SUPPORT 1
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
//Temperature
#define NTC_SUPPORT 1
#define SENSOR_SUPPORT 1
#define NTC_BETA 3350
#define NTC_R_UP 10000
#define NTC_R_DOWN 0
#define NTC_R0 8000
#elif defined(ALLTERCO_SHELLY25)
// Info
#define MANUFACTURER "ALLTERCO"
#define DEVICE "SHELLY25"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT
#define BUTTON1_RELAY 1
#define BUTTON1_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON1_RELEASE BUTTON_ACTION_TOGGLE
#define BUTTON2_PIN 5
#define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_BOOT
#define BUTTON2_RELAY 2
#define BUTTON2_PRESS BUTTON_ACTION_TOGGLE
#define BUTTON2_RELEASE BUTTON_ACTION_TOGGLE
#define BUTTON3_PIN 2
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_LNGCLICK BUTTON_ACTION_RESET
#define BUTTON3_LNGLNGCLICK BUTTON_ACTION_FACTORY
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 15
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// Light
#define LED1_PIN 0
#define LED1_PIN_INVERSE 1
//Temperature
#define NTC_SUPPORT 1
#define SENSOR_SUPPORT 1
#define NTC_BETA 3350
#define NTC_R_UP 10000
#define NTC_R_DOWN 0
#define NTC_R0 8000
//Current
#define ADE7953_SUPPORT 1
#define I2C_SDA_PIN 12
#define I2C_SCL_PIN 14
// -----------------------------------------------------------------------------
// This device has teh same behaviour as the GOSUND WP3, but with different GPIO pin values
// GPIO equivalents extracted from https://templates.blakadder.com/aoycocr_X5P.html
#elif defined(AOYCOCR_X5P)
// Info
#define MANUFACTURER "AOYCOCR"
#define DEVICE "X5P"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// the defaults are reasonable, but you can change them as desired
//#define BUTTON1_PRESS BUTTON_ACTION_NONE
//#define BUTTON1_CLICK BUTTON_ACTION_TOGGLE
//#define BUTTON1_DBLCLICK BUTTON_ACTION_AP
//#define BUTTON1_LNGCLICK BUTTON_ACTION_RESET
//#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_FACTORY
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
// LED1 (red) indicates on/off state; you could use LED_MODE_FOLLOW_INVERSE
// so that the LED lights the button when 'off' so it can be found easily.
#define LED1_PIN 0
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_FOLLOW
#define LED1_RELAY 1
// LED2 (blue) indicates wifi activity
#define LED2_PIN 2
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_WIFI
// -----------------------------------------------------------------------------
// also works with https://www.amazon.com/gp/product/B07TMY394G/
// see https://github.com/xoseperez/espurna/issues/2055
#elif defined(LOHAS_E27_9W)
// Info
#define MANUFACTURER "LOHAS"
#define DEVICE "E27_9W"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define MY92XX_MODEL MY92XX_MODEL_MY9231
#define MY92XX_CHIPS 2
#define MY92XX_DI_PIN 13
#define MY92XX_DCKI_PIN 15
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3, 4
#define LIGHT_WHITE_FACTOR (0.1) // White LEDs are way more bright in the B1
// https://www.amazon.com/gp/product/B07T7W7ZMW
#elif defined(LOHAS_E26_A19)
// Info
#define MANUFACTURER "LOHAS"
#define DEVICE "E26_A19"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE1
#define LIGHT_CH5_PIN 12 // WHITE1
// -----------------------------------------------------------------------------
#elif defined(TECKIN_SB53)
// Info
#define MANUFACTURER "TECKIN"
#define DEVICE "SB53"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 4 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 13 // WARM WHITE
#define LIGHT_CH5_PIN 5 // COLD WHITE
// -----------------------------------------------------------------------------
#elif defined(XIAOMI_SMART_DESK_LAMP)
// Info
#define MANUFACTURER "XIAOMI"
#define DEVICE "SMART_DESK_LAMP"
// Buttons
#define BUTTON1_PIN 2
#define BUTTON2_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP
// This button doubles as switch here and as encoder mode switch below
// Clicking it (for less than 500ms) will turn the light on and off
// Double and Long clicks will not work as these are used to modify the encoder action
#define BUTTON1_RELAY 1
#define BUTTON_LNGCLICK_DELAY 500
#define BUTTON1_DBLCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGCLICK BUTTON_ACTION_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE
// Hidden button will enter AP mode if dblclick and reset the device when long-long-clicked
#define BUTTON2_DBLCLICK BUTTON_ACTION_AP
#define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET
// Light
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define LIGHT_STEP 8
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 5 // warm white
#define LIGHT_CH2_PIN 4 // cold white
// https://www.xiaomitoday.com/xiaomi-mijia-mjtd01yl-led-desk-lamp-review/
#define LIGHT_COLDWHITE_MIRED 153
#define LIGHT_WARMWHITE_MIRED 370
// Encoder
// If mode is ENCODER_MODE_RATIO, the value ratio between both channels is changed
// when the button is not pressed, and the overall brightness when pressed
// If mode is ENCODER_MODE_CHANNEL, the first channel value is changed
// when the button is not pressed, and the second channel when pressed
// If no ENCODERX_BUTTON_PIN defined it will only change the value of the first defined channel
#define ENCODER_SUPPORT 1
#define ENCODER1_PIN1 12
#define ENCODER1_PIN2 13
#define ENCODER1_BUTTON_PIN 2 // active low by default, with software pullup
#define ENCODER1_CHANNEL1 0 // please note this value is 0-based (LIGHT_CH1 above)
#define ENCODER1_CHANNEL2 1 // please note this value is 0-based (LIGHT_CH2 above)
#define ENCODER1_MODE ENCODER_MODE_RATIO
#elif defined(PHYX_ESP12_RGB)
// Info
#define MANUFACTURER "PHYX"
#define DEVICE "ESP12_RGB"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 4 // RED
#define LIGHT_CH2_PIN 14 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
// -----------------------------------------------------------------------------
// iWoole LED Table Lamp
// http://iwoole.com/newst-led-smart-night-light-7w-smart-table-light-rgbw-wifi-app-remote-control-110v-220v-us-eu-plug-smart-lamp-google-home-decore-p00022p1.html
// -----------------------------------------------------------------------------
#elif defined(IWOOLE_LED_TABLE_LAMP)
// Info
#define MANUFACTURER "IWOOLE"
#define DEVICE "LED_TABLE_LAMP"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 4 // WHITE
// -----------------------------------------------------------------------------
// Generic GU10
// https://www.ebay.com/itm/1-10PC-GU10-RGB-Smart-Bulb-Wireless-WiFi-App-Remote-Ctrl-Light-for-Alexa-Google/173724116351
// -----------------------------------------------------------------------------
#elif defined(GENERIC_GU10)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "GU10"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 4 // WHITE
// -----------------------------------------------------------------------------
// Generic E14
// https://www.ebay.com/itm/LED-Bulb-Wifi-E14-4-5W-Candle-RGB-W-4in1-Dimmable-V-tac-Smart-VT-5114/163899840601
// -----------------------------------------------------------------------------
#elif defined(GENERIC_E14)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "E14"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 4 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 5 // WHITE
// -----------------------------------------------------------------------------
// Deltaco white e14 (SH-LE14W) and e27 (SH-LE27W)
// -----------------------------------------------------------------------------
#elif defined(DELTACO_SH_LEXXW)
// Info
#define MANUFACTURER "DELTACO"
#define DEVICE "SH_LEXXW"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 12 // WARM WHITE
#define LIGHT_CH2_PIN 14 // COLD WHITE
// -----------------------------------------------------------------------------
// Deltaco rgbw e27 (SH-LE27RGB)
// -----------------------------------------------------------------------------
#elif defined(DELTACO_SH_LEXXRGB)
// Info
#define MANUFACTURER "DELTACO"
#define DEVICE "SH_LEXXRGB"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 14 // WARM WHITE
#define LIGHT_CH5_PIN 12 // COLD WHITE
// -----------------------------------------------------------------------------
// Nexete A19
// https://www.ebay.com/itm/Wifi-Smart-LED-light-Bulb-9W-60W-A19-850LM-RGBW-Dimmable-for-Alexa-Google-Home/283514779201
// -----------------------------------------------------------------------------
#elif defined(NEXETE_A19)
// Info
#define MANUFACTURER "NEXETE"
#define DEVICE "A19"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 15 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 5 // WHITE
// -----------------------------------------------------------------------------
// Lombex Lux Nova 2 Tunable White
// https://www.amazon.com/Lombex-Compatible-Equivalent-Dimmable-2700K-6500K/dp/B07B8K72PR
// -----------------------------------------------------------------------------
#elif defined(LOMBEX_LUX_NOVA2_TUNABLE_WHITE)
// Info
#define MANUFACTURER "LOMBEX"
#define DEVICE "LUX_NOVA2_TUNABLE_WHITE"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 4
#define MY92XX_DCKI_PIN 5
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
// No RGB on this bulb. Warm white on channel 0, cool white on channel 3
#define MY92XX_MAPPING 255, 255, 255, 3, 0
// -----------------------------------------------------------------------------
// Lombex Lux Nova 2 White and Color
// https://www.amazon.com/Lombex-Compatible-Equivalent-Dimmable-2700K-6500K/dp/B07B8K72PR
// -----------------------------------------------------------------------------
#elif defined(LOMBEX_LUX_NOVA2_WHITE_COLOR)
// Info
#define MANUFACTURER "LOMBEX"
#define DEVICE "LUX_NOVA2_WHITE_COLOR"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 4
#define MY92XX_DCKI_PIN 5
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
// RGB on channels 0/1/2, either cool or warm white on channel 3
// The bulb *should* have cool leds, but could also have warm leds as a common defect
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// Bestek Smart Plug with 2 USB ports
// https://www.bestekcorp.com/bestek-smart-plug-works-with-amazon-alexa-google-assistant-and-ifttt-with-2-usb
// -----------------------------------------------------------------------------
#elif defined(BESTEK_MRJ1011)
// Info
#define MANUFACTURER "BESTEK"
#define DEVICE "MRJ1011"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relay
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LED
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// GBLIFE RGBW SOCKET
// -----------------------------------------------------------------------------
#elif defined(GBLIFE_RGBW_SOCKET)
// Info
#define MANUFACTURER "GBLIFE"
#define DEVICE "RGBW_SOCKET"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// Light RGBW
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 14 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 4 // WHITE
// ----------------------------------------------------------------------------------------
// Smart life Mini Smart Socket is similar Homecube 16A but some GPIOs differ
// https://www.ebay.de/itm/Smart-Steckdose-WIFI-WLAN-Amazon-Alexa-Fernbedienung-Home-Socket-Zeitschaltuh-DE/123352026749?hash=item1cb85a8e7d:g:IasAAOSwk6dbj390
// Also labeled NETVIP
// https://www.amazon.es/Inteligente-NETVIP-Inal%C3%A1mbrico-Interruptor-Funciona/dp/B07KH8YWS5
// ----------------------------------------------------------------------------------------
#elif defined(SMARTLIFE_MINI_SMART_SOCKET)
// Info
#define MANUFACTURER "SMARTLIFE"
#define DEVICE "MINI_SMART_SOCKET"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
//Red LED: 0
//Green LED: 4
//Blue LED: 2
// Light
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 0 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 2 // BLUE
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// ----------------------------------------------------------------------------------------
// Hama WiFi Steckdose (00176533)
// https://at.hama.com/00176533/hama-wifi-steckdose-3500w-16a
// ----------------------------------------------------------------------------------------
#elif defined(HAMA_WIFI_STECKDOSE_00176533)
// Info
#define MANUFACTURER "HAMA"
#define DEVICE "WIFI_STECKDOSE_00176533"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Oxaoxe NX-SP202
// Digoo NX-SP202 (not tested)
// Digoo DG-SP202 (not tested)
// https://github.com/xoseperez/espurna/issues/1502
// -----------------------------------------------------------------------------
#elif defined(DIGOO_NX_SP202)
// Info
#define MANUFACTURER "DIGOO"
#define DEVICE "NX_SP202"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 16
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 14
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 23296
#define HLW8012_VOLTAGE_RATIO 310085
#define HLW8012_POWER_RATIO 3368471
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// Foxel's LightFox dual
// https://github.com/foxel/esp-dual-rf-switch
// -----------------------------------------------------------------------------
#elif defined(FOXEL_LIGHTFOX_DUAL)
// Info
#define MANUFACTURER "FOXEL"
#define DEVICE "LIGHTFOX_DUAL"
#define SERIAL_BAUDRATE 19200
#define RELAY_PROVIDER RELAY_PROVIDER_DUAL
#define DUMMY_RELAY_COUNT 2
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 2
#define BUTTON4_RELAY 1
#define BUTTON_PROVIDER_FOXEL_LIGHTFOX_DUAL_SUPPORT 1
// -----------------------------------------------------------------------------
// Teckin SP20
// -----------------------------------------------------------------------------
#elif defined(TECKIN_SP20)
// Info
#define MANUFACTURER "TECKIN"
#define DEVICE "SP20"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#define LED2_PIN 0
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_FINDME
#define LED2_RELAY 0
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// Charging Essentials / LITESUN LA-WF3
// -----------------------------------------------------------------------------
#elif defined(LITESUN_LA_WF3)
// Info
#define MANUFACTURER "LITESUN"
#define DEVICE "LA_WF3"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4 // 4 blue led
#define LED1_MODE LED_MODE_WIFI
#define LED1_PIN_INVERSE 1
#define LED2_PIN 5 // 5 red led
#define LED2_MODE LED_MODE_RELAY
#define LED2_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// PSH
// -----------------------------------------------------------------------------
#elif defined(PSH_WIFI_PLUG)
// Info
#define MANUFACTURER "PSH"
#define DEVICE "WIFI_PLUG"
// Relays
#define RELAY1_PIN 2
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0
#define LED1_PIN_INVERSE 0
#elif defined(PSH_RGBW_CONTROLLER)
// Info
#define MANUFACTURER "PSH"
#define DEVICE "RGBW_CONTROLLER"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE1
#elif defined(PSH_WIFI_SENSOR)
// Info
#define MANUFACTURER "PSH"
#define DEVICE "WIFI_SENSOR"
// DHT12 Sensor
#define DHT_SUPPORT 1
#define DHT_PIN 14
#define DHT_TYPE DHT_CHIP_DHT12
// LDR Sensor
#define LDR_SUPPORT 1
#define LDR_TYPE LDR_GL5528
#define LDR_ON_GROUND false
#define LDR_RESISTOR 10000
#elif defined(JINVOO_VALVE_SM_AW713)
// Reflashing from original Tuya firmware
// to thirdparty firmware like espurna by:
// https://github.com/ct-Open-Source/tuya-convert
// Info
#define MANUFACTURER "JINVOO"
#define DEVICE "VALVE_SM_AW713"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LED
#define LED1_PIN 5 // 5 red led
#define LED1_PIN_INVERSE 0
#define LED1_RELAY 1
#define LED1_MODE LED_MODE_RELAY
#define LED2_PIN 4 // 4 blue led
#define LED2_PIN_INVERSE 0
#define LED2_RELAY 1
#define LED2_MODE LED_MODE_FINDME_WIFI
#elif defined(TUYA_GENERIC_DIMMER)
#define MANUFACTURER "TUYA"
#define DEVICE "GENERIC_DIMMER"
#define LIGHT_PROVIDER LIGHT_PROVIDER_TUYA
#define LIGHT_CHANNELS 0
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define DUMMY_RELAY_COUNT 0
// -----------------------------------------------------------------------------
// Etekcity ESW01-USA
// https://www.amazon.com/Etekcity-Voltson-Outlet-Monitoring-Required/dp/B01M3MYIFS
// -----------------------------------------------------------------------------
#elif defined(ETEKCITY_ESW01_USA)
// Info
#define MANUFACTURER "ETEKCITY"
#define DEVICE "ESW01_USA"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
// Blue
#define LED1_PIN 5
#define LED1_MODE LED_MODE_WIFI
// Yellow
#define LED2_PIN 16
#define LED2_MODE LED_MODE_FOLLOW
#define LED2_RELAY 1
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 15
#define HLW8012_CF1_PIN 12
#define HLW8012_CF_PIN 13
#define HLW8012_SEL_CURRENT HIGH // SEL pin to HIGH to measure current
#define HLW8012_CURRENT_R 0.001 // Current resistor
#define HLW8012_VOLTAGE_R_UP ( 4 * 470000 ) // Upstream voltage resistor
#define HLW8012_VOLTAGE_R_DOWN ( 1000 ) // Downstream voltage resistor
#define HLW8012_INTERRUPT_ON CHANGE
// -----------------------------------------------------------------------------
// FS UAP1
// http://frank-schuetz.de/index.php/fhem/13-hoermann-torantrieb-mit-espeasy-in-fhem-einbinden
#elif defined(FS_UAP1)
// Info
#define MANUFACTURER "FS"
#define DEVICE "UAP1"
// Inputs
#define DIGITAL1_PIN 4
#define DIGITAL2_PIN 5
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY3_PIN 14
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
// Disable UART noise
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// TFLAG NX-SM100 & NX-SM200
// -----------------------------------------------------------------------------
#elif defined(TFLAG_NX_SMX00)
// Info
#define MANUFACTURER "TFLAG"
#define DEVICE "NX_SMX00"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0
#define LED1_PIN_INVERSE 1
#define LED1_MODE LED_MODE_FOLLOW_INVERSE
#define LED1_RELAY 1
#define LED2_PIN 15
#define LED2_PIN_INVERSE 1
#define LED2_MODE LED_MODE_WIFI
// HJL01 / BL0937
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 16
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 632
#define HLW8012_VOLTAGE_RATIO 313400
#define HLW8012_POWER_RATIO 3711185
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// MUVIT_IO_MIOBULB001
// -----------------------------------------------------------------------------
#elif defined(MUVIT_IO_MIOBULB001)
// Info
#define MANUFACTURER "MUVIT_IO"
#define DEVICE "MIOBULB001"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 4 // WHITE
// -----------------------------------------------------------------------------
// Hykker Power Plug (Smart Home Series) available in Jerónimo Martins Polska (Biedronka)
// https://www.hykker.com/akcesoria/gniazdo-wi-fi-z-licznikiem-energii/
// Reflashing from original Tuya firmware
// to thirdparty firmware like espurna by:
// https://github.com/ct-Open-Source/tuya-convert
// -----------------------------------------------------------------------------
#elif defined(HYKKER_SMART_HOME_POWER_PLUG)
// Info
#define MANUFACTURER "HYKKER"
#define DEVICE "SMART_HOME_POWER_PLUG"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LED
// Red
#define LED1_PIN 13
#define LED1_MODE LED_MODE_WIFI
#define LED1_PIN_INVERSE 1
// Blue connected to relay
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 282060
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// Kogan Smarter Home Plug with Energy Meter (Australia)
// Product code: KASPEMHA
// https://www.kogan.com/au/buy/kogan-smarterhome-smart-plug-energy-meter/
// Reflashing from original Tuya firmware
// to thirdparty firmware like espurna by:
// https://github.com/ct-Open-Source/tuya-convert
// -----------------------------------------------------------------------------
#elif defined(KOGAN_SMARTER_HOME_PLUG_W_POW)
// Info
#define MANUFACTURER "KOGAN"
#define DEVICE "SMARTER_HOME_PLUG_W_POW"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LED
// Red
#define LED1_PIN 13
#define LED1_MODE LED_MODE_WIFI
#define LED1_PIN_INVERSE 1
// Blue connected to relay
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_SEL_CURRENT LOW
#define HLW8012_CURRENT_RATIO 25740
#define HLW8012_VOLTAGE_RATIO 282060
#define HLW8012_POWER_RATIO 3414290
#define HLW8012_INTERRUPT_ON FALLING
// -----------------------------------------------------------------------------
// KINGART_CURTAIN_SWITCH
// -----------------------------------------------------------------------------
#elif defined(KINGART_CURTAIN_SWITCH)
// Info
#define MANUFACTURER "KINGART"
#define DEVICE "CURTAIN_SWITCH"
#define CURTAIN_SUPPORT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// KINGART module handles the UART, can't print any debug messages
#define KINGART_CURTAIN_SUPPORT 1
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// LSC Smart LED Light Strip (Smart CXonnect Series) available ACTION (Germany)
// https://www.action.com/de-de/p/lsc-smart-connect-intelligenter-multicolor-led-strip-/
// Reflashing from original Tuya firmware
// to thirdparty firmware like espurna by:
// https://github.com/ct-Open-Source/tuya-convert
// -----------------------------------------------------------------------------
#elif defined(LSC_SMART_LED_LIGHT_STRIP)
// Info
#define MANUFACTURER "LSC"
#define DEVICE "SMART_LED_LIGHT_STRIP"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light RGBW
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 4 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE
// #define LIGHT_CH5_PIN 5 // CW (not connected, but circuit supports it)
// IR
#define IR_SUPPORT 1
#define IR_RX_PIN 0
#define IR_BUTTON_SET 5
// -----------------------------------------------------------------------------
// eHomeDIY WT02
// https://github.com/eHomeDIY/WT02-hardware
// -----------------------------------------------------------------------------
#elif defined(EHOMEDIY_WT02)
// Info
#define MANUFACTURER "EHOMEDIY"
#define DEVICE "WT02"
#define I2C_SDA_PIN 0
#define I2C_SCL_PIN 2
#define BMX280_SUPPORT 1
// #define SI7021_SUPPORT 1
// -----------------------------------------------------------------------------
// eHomeDIY WT03
// https://github.com/eHomeDIY/WT03-hardware
// -----------------------------------------------------------------------------
#elif defined(EHOMEDIY_WT03)
// Info
#define MANUFACTURER "EHOMEDIY"
#define DEVICE "WT03"
#define I2C_SDA_PIN 2
#define I2C_SCL_PIN 0
#define BMX280_SUPPORT 1
// #define SI7021_SUPPORT 1
// -----------------------------------------------------------------------------
// Linksprite R4
// http://linksprite.com/wiki/index.php?title=LinkNode_R4:_Arduino-compatible_WiFi_relay_controller
// -----------------------------------------------------------------------------
#elif defined(LINKSPRITE_LINKNODE_R4)
// Info
#define MANUFACTURER "LINKSPRITE"
#define DEVICE "LINKNODE_R4"
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY3_PIN 14
#define RELAY4_PIN 16
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// NEDIS WIFIP310FWT Wi-Fi Smart Extension Socket
// 3x Schuko Type F, 4x USB, 16 A
// https://nedis.com/en-us/product/smart-living/smart-home/energy/550672299/wi-fi-smart-extension-socket-3x-schuko-type-f-4x-usb-16-a
// -----------------------------------------------------------------------------
#elif defined(NEDIS_WIFIP310FWT)
// Info
#define MANUFACTURER "NEDIS"
#define DEVICE "WIFIP310FWT"
// Based on the reporter, this product uses GPIO1 and 3 for the button
// and onboard LED, so hardware serial should be disabled...
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON1_PIN 3
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 5
#define RELAY2_PIN 4
#define RELAY3_PIN 13
#define RELAY4_PIN 14
// LEDs
#define LED1_PIN 1
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Arlec Smart PC190HA Plug
// https://templates.blakadder.com/arlec_PC190HA.html
// -----------------------------------------------------------------------------
#elif defined(ARLEC_PC190HA)
// Info
#define MANUFACTURER "ARLEC"
#define DEVICE "PC190HA"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4 // blue LED
#define LED1_PIN_INVERSE 1
#define LED2_PIN 13 // red LED
#define LED2_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Arlec Smart PB89HA Power Strip
// https://templates.blakadder.com/arlec_PB89HA.html
// -----------------------------------------------------------------------------
#elif defined(ARLEC_PB89HA)
// Info
#define MANUFACTURER "ARLEC"
#define DEVICE "PB89HA"
// Buttons
#define BUTTON1_PIN 3
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 5
#define RELAY2_PIN 4
#define RELAY3_PIN 13
#define RELAY4_PIN 12
// LEDs
#define LED1_PIN 1
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Prodino WIFI
// https://kmpelectronics.eu/products/prodino-wifi-v1/
// -----------------------------------------------------------------------------
#elif defined(PRODINO_WIFI)
// Info
#define MANUFACTURER "PRODINO"
#define DEVICE "WIFI"
// MCP23S08
#define MCP23S08_SUPPORT 1
// Relays
#define RELAY_PROVIDER RELAY_PROVIDER_MCP23S08
#define RELAY1_PIN 4
#define RELAY2_PIN 5
#define RELAY3_PIN 6
#define RELAY4_PIN 7
// Buttons
#define BUTTON1_PROVIDER BUTTON_PROVIDER_MCP23S08
#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PIN 0
#define BUTTON2_PROVIDER BUTTON_PROVIDER_MCP23S08
#define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PIN 1
#define BUTTON3_PROVIDER BUTTON_PROVIDER_MCP23S08
#define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_PIN 2
#define BUTTON4_PROVIDER BUTTON_PROVIDER_MCP23S08
#define BUTTON4_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_PIN 3
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
#define BUTTON4_RELAY 4
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Fcmila E27 7W RGB+W Bulb
// https://www.aliexpress.com/item/32925895199.html
// -----------------------------------------------------------------------------
#elif defined(FCMILA_E27_7W_RGBW)
// Info
#define MANUFACTURER "FCMILA"
#define DEVICE "E27_7W_RGBW"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 4 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 5 // WHITE
// -----------------------------------------------------------------------------
// Benexmart 5W GU5.3 (MR16) RGBWW
// https://www.aliexpress.com/item/4001245365644.html
// -----------------------------------------------------------------------------
#elif defined(BENEXMART_GU53_RGBWW)
// Info
#define MANUFACTURER "BENEXMART"
#define DEVICE "GU53_RGBWW"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 4 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 5 // WARM WHITE
#define LIGHT_CH5_PIN 13 // COLD WHITE
// LSC E27 10W White Bulb with TYLC6E ESP8266 module
// https://www.action.com/de-at/p/lsc-smart-connect-intelligente-led-lampe/
// -----------------------------------------------------------------------------
#elif defined(LSC_E27_10W_WHITE)
// Info
#define MANUFACTURER "LSC"
#define DEVICE "E27_10W_WHITE"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 5 // WARM WHITE LED PWM PIN
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_PIN 4 // COLD WHITE LED PWM PIN
#define LIGHT_CH2_INVERSE 0
#else
#error "UNSUPPORTED HARDWARE!!"
#endif