// ----------------------------------------------------------------------------- // Configuration HELP // ----------------------------------------------------------------------------- // // MANUFACTURER: Name of the manufacturer of the board ("string") // DEVICE: Name of the device ("string") // BUTTON#_PIN: GPIO for the n-th button (1-based, up to 4 buttons) // BUTTON#_RELAY: Relay number that will be bind to the n-th button (1-based) // BUTTON#_MODE: A mask of options (BUTTON_PUSHBUTTON and BUTTON_SWITCH cannot be together) // - BUTTON_PUSHBUTTON: button event is fired when released // - BUTTON_SWITCH: button event is fired when pressed or released // - BUTTON_DEFAULT_HIGH: there is a pull up in place // - BUTTON_SET_PULLUP: set pullup by software // RELAY#_PIN: GPIO for the n-th relay (1-based, up to 4 relays) // RELAY#_TYPE: Relay can be RELAY_TYPE_NORMAL, RELAY_TYPE_INVERSE or RELAY_TYPE_LATCHED // LED#_PIN: GPIO for the n-th LED (1-based, up to 4 LEDs) // LED#_PIN_INVERSE: LED has inversed logic (lit when pulled down) // LED#_MODE: Check hardware.h for LED_MODE_% // LED#_RELAY: Linked relay (1-based) // // Besides, other hardware specific information should be stated here // ----------------------------------------------------------------------------- // Development boards // ----------------------------------------------------------------------------- #if defined(NODEMCU_LOLIN) // Info #define MANUFACTURER "NODEMCU" #define DEVICE "LOLIN" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 4 #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_PIN 12 #define RELAY3_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #elif defined(WEMOS_D1_MINI_RELAYSHIELD) // Info #define MANUFACTURER "WEMOS" #define DEVICE "D1_MINI_RELAYSHIELD" // Buttons // No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems #define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND, // it's the same as using a Wemos one button shield #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #elif defined(WEMOS_D1_TARPUNA_SHIELD) // Info #define MANUFACTURER "WEMOS" #define DEVICE "D1_TARPUNA_SHIELD" // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // ESPurna // ----------------------------------------------------------------------------- #elif defined(TINKERMAN_ESPURNA_H06) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_H06" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Normal pushbutton #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_INVERSE // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 2 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(TINKERMAN_ESPURNA_H08) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_H08" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Normal pushbutton #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 5 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(TINKERMAN_ESPURNA_SWITCH) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_SWITCH" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Touch button #define BUTTON1_MODE BUTTON_PUSHBUTTON #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_INVERSE // ----------------------------------------------------------------------------- // Itead Studio boards // ----------------------------------------------------------------------------- #elif defined(ITEAD_SONOFF_BASIC) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_BASIC" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 14 #define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP #define BUTTON2_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_RF) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_RF" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 14 #define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP #define BUTTON2_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_TH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_TH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Jack is connected to GPIO14 (and with a small hack to GPIO4) #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 14 #ifndef DHT_SUPPORT #define DHT_SUPPORT 1 #endif #define DHT_PIN 14 //#define I2C_SDA_PIN 4 //#define I2C_SCL_PIN 14 #elif defined(ITEAD_SONOFF_SV) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_SV" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SLAMPHER) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SLAMPHER" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_S20) // Info #define MANUFACTURER "ITEAD" #define DEVICE "S20" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_TOUCH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_TOUCH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_POW) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_POW" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 15 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 5 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(ITEAD_SONOFF_DUAL) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_DUAL" #define SERIAL_BAUDRATE 19230 #define RELAY_PROVIDER RELAY_PROVIDER_DUAL #define DUMMY_RELAY_COUNT 2 #define DEBUG_SERIAL_SUPPORT 0 #define TERMINAL_SUPPORT 0 // Buttons #define BUTTON3_RELAY 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_DUAL_R2) #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_DUAL_R2" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 1 #define BUTTON1_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP #define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_4CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_4CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON4_PIN 14 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 #define BUTTON4_RELAY 4 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_4CH_PRO) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_4CH_PRO" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON4_PIN 14 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 #define BUTTON4_RELAY 4 // Sonoff 4CH Pro uses a secondary STM32 microcontroller to handle // buttons and relays, but it also forwards button presses to the ESP8285. // This allows ESPurna to handle button presses -almost- the same way // as with other devices except: // * Double click seems to break/disable the button on the STM32 side // * With S6 switch to 1 (self-locking and inching modes) everything's OK // * With S6 switch to 0 (interlock mode) if there is a relay ON // and you click on another relay button, the STM32 sends a "press" // event for the button of the first relay (to turn it OFF) but it // does not send a "release" event. It's like it's holding the // button down since you can see it is still LOW. // Whatever reason the result is that it may actually perform a // long click or long-long click. // The configuration below make the button toggle the relay on press events // and disables any possibly harmful combination with S6 set to 0. // If you are sure you will only use S6 to 1 you can comment the // BUTTON1_LNGCLICK and BUTTON1_LNGLNGCLICK options below to recover the // AP mode and factory reset functionalities. #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE #define BUTTON2_PRESS BUTTON_MODE_TOGGLE #define BUTTON2_CLICK BUTTON_MODE_NONE #define BUTTON3_PRESS BUTTON_MODE_TOGGLE #define BUTTON3_CLICK BUTTON_MODE_NONE #define BUTTON4_PRESS BUTTON_MODE_TOGGLE #define BUTTON4_CLICK BUTTON_MODE_NONE // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_1CH_INCHING) // The inching functionality is managed by a misterious IC in the board. // You cannot control the inching button and functionality from the ESP8266 // Besides, enabling the inching functionality using the hardware button // will result in the relay switching on and off continuously. // Fortunately the unkown IC keeps memory of the hardware inching status // so you can just disable it and forget. The inching LED must be lit. // You can still use the pulse options from the web interface // without problem. // Info #define MANUFACTURER "ITEAD" #define DEVICE "1CH_INCHING" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_MOTOR) // Info #define MANUFACTURER "ITEAD" #define DEVICE "MOTOR" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_BNSZ01) // Info #define MANUFACTURER "ITEAD" #define DEVICE "BNSZ01" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 1 #define LIGHT_CH1_PIN 12 #define LIGHT_CH1_INVERSE 0 #elif defined(ITEAD_SONOFF_RFBRIDGE) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_RFBRIDGE" #define SERIAL_BAUDRATE 19200 #define RELAY_PROVIDER RELAY_PROVIDER_RFBRIDGE #ifndef DUMMY_RELAY_COUNT #define DUMMY_RELAY_COUNT 8 #endif // Remove UART noise on serial line #define TERMINAL_SUPPORT 0 #define DEBUG_SERIAL_SUPPORT 0 // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_B1) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_B1" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define MY92XX_MODEL MY92XX_MODEL_MY9231 #define MY92XX_CHIPS 2 #define MY92XX_DI_PIN 12 #define MY92XX_DCKI_PIN 14 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 4, 3, 5, 0, 1 #elif defined(ITEAD_SONOFF_LED) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_LED" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 12 // Cold white #define LIGHT_CH2_PIN 14 // Warm white #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #elif defined(ITEAD_SONOFF_T1_1CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_1CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_T1_2CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_2CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_MODE_TOGGLE #define BUTTON2_CLICK BUTTON_MODE_NONE #define BUTTON2_DBLCLICK BUTTON_MODE_NONE #define BUTTON2_LNGCLICK BUTTON_MODE_NONE #define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_T1_3CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_3CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_MODE_TOGGLE #define BUTTON1_CLICK BUTTON_MODE_NONE #define BUTTON1_DBLCLICK BUTTON_MODE_NONE #define BUTTON1_LNGCLICK BUTTON_MODE_NONE #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_MODE_TOGGLE #define BUTTON2_CLICK BUTTON_MODE_NONE #define BUTTON2_DBLCLICK BUTTON_MODE_NONE #define BUTTON2_LNGCLICK BUTTON_MODE_NONE #define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_PRESS BUTTON_MODE_TOGGLE #define BUTTON3_CLICK BUTTON_MODE_NONE #define BUTTON3_DBLCLICK BUTTON_MODE_NONE #define BUTTON3_LNGCLICK BUTTON_MODE_NONE #define BUTTON3_LNGLNGCLICK BUTTON_MODE_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // YJZK // ----------------------------------------------------------------------------- #elif defined(YJZK_SWITCH_2CH) // Info #define MANUFACTURER "YJZK" #define DEVICE "SWITCH_2CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Electrodragon boards // ----------------------------------------------------------------------------- #elif defined(ELECTRODRAGON_WIFI_IOT) // Info #define MANUFACTURER "ELECTRODRAGON" #define DEVICE "WIFI_IOT" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 2 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 16 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // WorkChoice ecoPlug // ----------------------------------------------------------------------------- #elif defined(WORKCHOICE_ECOPLUG) // Info #define MANUFACTURER "WORKCHOICE" #define DEVICE "ECOPLUG" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // AI Thinker // ----------------------------------------------------------------------------- #elif defined(AITHINKER_AI_LIGHT) // Info #define MANUFACTURER "AITHINKER" #define DEVICE "AI_LIGHT" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 13 #define MY92XX_DCKI_PIN 15 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // LED Controller // ----------------------------------------------------------------------------- #elif defined(MAGICHOME_LED_CONTROLLER) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "LED_CONTROLLER" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 13 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_PIN 4 #define IR_BUTTON_SET 1 #elif defined(MAGICHOME_LED_CONTROLLER_20) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "LED_CONTROLLER_20" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_PIN 4 #define IR_BUTTON_SET 1 // ----------------------------------------------------------------------------- // HUACANXING H801 & H802 // ----------------------------------------------------------------------------- #elif defined(HUACANXING_H801) // Info #define MANUFACTURER "HUACANXING" #define DEVICE "H801" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define DEBUG_PORT Serial1 // LEDs #define LED1_PIN 5 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 15 // RED #define LIGHT_CH2_PIN 13 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 14 // WHITE1 #define LIGHT_CH5_PIN 4 // WHITE2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(HUACANXING_H802) // Info #define MANUFACTURER "HUACANXING" #define DEVICE "H802" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define DEBUG_PORT Serial1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 14 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Jan Goedeke Wifi Relay // https://github.com/JanGoe/esp8266-wifi-relay // ----------------------------------------------------------------------------- #elif defined(JANGOE_WIFI_RELAY_NC) // Info #define MANUFACTURER "JANGOE" #define DEVICE "WIFI_RELAY_NC" // Buttons #define BUTTON1_PIN 12 #define BUTTON2_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 2 #define RELAY2_PIN 14 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_TYPE RELAY_TYPE_INVERSE #elif defined(JANGOE_WIFI_RELAY_NO) // Info #define MANUFACTURER "JANGOE" #define DEVICE "WIFI_RELAY_NO" // Buttons #define BUTTON1_PIN 12 #define BUTTON2_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 2 #define RELAY2_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // Jorge García Wifi+Relays Board Kit // https://www.tindie.com/products/jorgegarciadev/wifi--relays-board-kit // https://github.com/jorgegarciadev/wifikit // ----------------------------------------------------------------------------- #elif defined(JORGEGARCIA_WIFI_RELAYS) // Info #define MANUFACTURER "JORGEGARCIA" #define DEVICE "WIFI_RELAYS" // Relays #define RELAY1_PIN 0 #define RELAY2_PIN 2 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_TYPE RELAY_TYPE_INVERSE // ----------------------------------------------------------------------------- // WiFi MQTT Relay / Thermostat // ----------------------------------------------------------------------------- #elif defined(OPENENERGYMONITOR_MQTT_RELAY) // Info #define MANUFACTURER "OPENENERGYMONITOR" #define DEVICE "MQTT_RELAY" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 16 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // WiOn 50055 Indoor Wi-Fi Wall Outlet & Tap // https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50050-Indoor-Wi-Fi-Outlet-Wireless-Switch-Programmable-Timer-%2F263112281551 // https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50055-Indoor-Wi-Fi-Wall-Tap-Monitor-Energy-Usage-Wireless-Smart-Switch-%2F263020837777 // ----------------------------------------------------------------------------- #elif defined(WION_50055) // Currently untested, does not support energy monitoring // Info #define MANUFACTURER "WION" #define DEVICE "50055" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // EX-Store Wifi Relay v3.1 // https://ex-store.de/ESP8266-WiFi-Relay-V31 // ----------------------------------------------------------------------------- #elif defined(EXS_WIFI_RELAY_V31) // Untested // Info #define MANUFACTURER "EXS" #define DEVICE "WIFI_RELAY_V31" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 13 #define RELAY1_TYPE RELAY_TYPE_LATCHED #define RELAY1_RESET_PIN 12 // ----------------------------------------------------------------------------- // V9261F // ----------------------------------------------------------------------------- #elif defined(GENERIC_V9261F) // Info #define MANUFACTURER "GENERIC" #define DEVICE "V9261F" #define ALEXA_SUPPORT 0 // V9261F #define V9261F_SUPPORT 1 #define V9261F_PIN 2 #define V9261F_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // ECH1560 // ----------------------------------------------------------------------------- #elif defined(GENERIC_ECH1560) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ECH1560" #define ALEXA_SUPPORT 0 // ECH1560 #define ECH1560_SUPPORT 1 #define ECH1560_CLK_PIN 4 #define ECH1560_MISO_PIN 5 #define ECH1560_INVERTED 0 // ----------------------------------------------------------------------------- // ESPLive // https://github.com/ManCaveMade/ESP-Live // ----------------------------------------------------------------------------- #elif defined(MANCAVEMADE_ESPLIVE) // Info #define MANUFACTURER "MANCAVEMADE" #define DEVICE "ESPLIVE" // Buttons #define BUTTON1_PIN 4 #define BUTTON2_PIN 5 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // DB18B20 #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 2 #define DALLAS_UPDATE_INTERVAL 5000 #define TEMPERATURE_MIN_CHANGE 1.0 // ----------------------------------------------------------------------------- // QuinLED // http://blog.quindorian.org/2017/02/esp8266-led-lighting-quinled-v2-6-pcb.html // ----------------------------------------------------------------------------- #elif defined(INTERMITTECH_QUINLED) // Info #define MANUFACTURER "INTERMITTECH" #define DEVICE "QUINLED" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 5 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 0 #define LIGHT_CH2_PIN 2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 // ----------------------------------------------------------------------------- // Arilux AL-LC06 // ----------------------------------------------------------------------------- #elif defined(ARILUX_AL_LC01) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC01" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 14 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #elif defined(ARILUX_AL_LC02) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC02" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #elif defined(ARILUX_AL_LC06) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC06" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE1 #define LIGHT_CH5_PIN 5 // WHITE2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(ARILUX_AL_LC11) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC11" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 13 // WHITE1 #define LIGHT_CH5_PIN 12 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(ARILUX_E27) // Info #define MANUFACTURER "ARILUX" #define DEVICE "E27" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 13 #define MY92XX_DCKI_PIN 15 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // XENON SM-PW701U // ----------------------------------------------------------------------------- #elif defined(XENON_SM_PW702U) // Info #define MANUFACTURER "XENON" #define DEVICE "SM_PW702U" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // AUTHOMETION LYT8266 // https://authometion.com/shop/en/home/13-lyt8266.html // ----------------------------------------------------------------------------- #elif defined(AUTHOMETION_LYT8266) // Info #define MANUFACTURER "AUTHOMETION" #define DEVICE "LYT8266" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 13 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 2 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_ENABLE_PIN 15 // ----------------------------------------------------------------------------- // Generic 8CH // ----------------------------------------------------------------------------- #elif defined(GENERIC_8CH) // Info #define MANUFACTURER "GENERIC" #define DEVICE "8CH" // Relays #define RELAY1_PIN 0 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 2 #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_PIN 4 #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_PIN 5 #define RELAY4_TYPE RELAY_TYPE_NORMAL #define RELAY5_PIN 12 #define RELAY5_TYPE RELAY_TYPE_NORMAL #define RELAY6_PIN 13 #define RELAY6_TYPE RELAY_TYPE_NORMAL #define RELAY7_PIN 14 #define RELAY7_TYPE RELAY_TYPE_NORMAL #define RELAY8_PIN 15 #define RELAY8_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // Unknown hardware // ----------------------------------------------------------------------------- #else #error "UNSUPPORTED HARDWARE!" #endif