// ----------------------------------------------------------------------------- // Configuration HELP // ----------------------------------------------------------------------------- // // Required: // // MANUFACTURER: Name of the manufacturer of the board ("string") // DEVICE: Name of the device ("string") // // For example, some configuration options for BUTTON, RELAY and LED modules. // See general.h, defaults.h and types.h for all of the available flags. // // BUTTON[1-8]_PIN: GPIO for the n-th button (1-based, up to 8 buttons) // BUTTON[1-8]_RELAY: Relay number that will be bind to the n-th button (1-based) // BUTTON[1-8]_CONFIG: Configuration mask (e.g. BUTTON_PUSHBUTTON and BUTTON_SWITCH cannot be together) // - BUTTON_PUSHBUTTON: button event is fired when released // - BUTTON_SWITCH: button event is fired when pressed or released // - BUTTON_DEFAULT_HIGH: there is a pull up in place // - BUTTON_SET_PULLUP: set pullup by software // // RELAY[1-8]_PIN: GPIO for the n-th relay (1-based, up to 8 relays) // RELAY[1-8]_TYPE: Relay can be RELAY_TYPE_NORMAL, RELAY_TYPE_INVERSE, RELAY_TYPE_LATCHED or RELAY_TYPE_LATCHED_INVERSE // // LED[1-8]_PIN: GPIO for the n-th LED (1-based, up to 8 LEDs) // LED[1-8]_PIN_INVERSE: LED has inversed logic (lit when pulled down) // LED[1-8]_MODE: Check types.h for LED_MODE_% // LED[1-8]_RELAY: Linked relay (1-based) // // Besides, other hardware specific information should be stated here #pragma once // ----------------------------------------------------------------------------- // Custom hardware // ----------------------------------------------------------------------------- #if defined(MANUFACTURER) and defined(DEVICE) // user has defined custom hardware, no need to check anything else // ----------------------------------------------------------------------------- // ESPurna Core // ----------------------------------------------------------------------------- #elif defined(ESPURNA_CORE) // This is a special device targeted to generate a light-weight binary image // meant to be able to do two-step-updates: // https://github.com/xoseperez/espurna/wiki/TwoStepUpdates // Info #define MANUFACTURER "ESPURNA" #define DEVICE "ESPURNA_CORE" // Disable non-core modules #define ALEXA_SUPPORT 0 #define API_SUPPORT 0 #define BROKER_SUPPORT 0 #define DEBUG_SERIAL_SUPPORT 0 #define DEBUG_TELNET_SUPPORT 0 #define DEBUG_WEB_SUPPORT 0 #define DOMOTICZ_SUPPORT 0 #define HOMEASSISTANT_SUPPORT 0 #define I2C_SUPPORT 0 #define MQTT_SUPPORT 0 #define NTP_SUPPORT 0 #define RPN_RULES_SUPPORT 0 #define SCHEDULER_SUPPORT 0 #define SENSOR_SUPPORT 0 #define THINGSPEAK_SUPPORT 0 #define WEB_SUPPORT 0 // Extra light-weight image //#define BUTTON_SUPPORT 0 // don't need / have buttons //#define LED_SUPPORT 0 // don't need wifi indicator //#define RELAY_SUPPORT 0 // don't need to preserve pin state between resets //#define OTA_ARDUINOOTA_SUPPORT 0 // when only using `ota` command //#define MDNS_SERVER_SUPPORT 0 // //#define TELNET_SUPPORT 0 // when only using espota.py //#define TERMINAL_SUPPORT 0 // #elif defined(ESPURNA_BASE) // This is a special device with no specific hardware // with the basics to easily upgrade it to a device-specific image // Info #define MANUFACTURER "ESPURNA" #define DEVICE "ESPURNA_BASE" // Disable non-core modules #define ALEXA_SUPPORT 0 #define API_SUPPORT 0 #define BROKER_SUPPORT 0 #define DOMOTICZ_SUPPORT 0 #define DEBUG_SERIAL_SUPPORT 0 //#define DEBUG_TELNET_SUPPORT 0 //#define DEBUG_WEB_SUPPORT 0 #define HOMEASSISTANT_SUPPORT 0 #define I2C_SUPPORT 0 #define MQTT_SUPPORT 0 #define NTP_SUPPORT 0 #define SCHEDULER_SUPPORT 0 #define SENSOR_SUPPORT 0 #define THINGSPEAK_SUPPORT 0 //#define WEB_SUPPORT 0 // Extra light-weight image #define BUTTON_SUPPORT 0 #define LED_SUPPORT 0 //#define MDNS_SERVER_SUPPORT 0 //#define TELNET_SUPPORT 0 //#define TERMINAL_SUPPORT 0 // ----------------------------------------------------------------------------- // Development boards // ----------------------------------------------------------------------------- #elif defined(NODEMCU_LOLIN) // Info #define MANUFACTURER "NODEMCU" #define DEVICE "LOLIN" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Hidden button will enter AP mode if dblclick and reset the device when long-long-clicked #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // Light #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #elif defined(NODEMCU_BASIC) // Info // Generic NodeMCU Board without any buttons or relays connected. #define MANUFACTURER "NODEMCU" #define DEVICE "BASIC" #elif defined(WEMOS_D1_MINI) // Info #define MANUFACTURER "WEMOS" #define DEVICE "D1_MINI" // Buttons // No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems #define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND, // it's the same as using a Wemos one button shield #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #define I2C_SDA_PIN 4 // D2 #define I2C_SCL_PIN 5 // D1 #elif defined(WEMOS_D1_MINI_RELAYSHIELD) // Info #define MANUFACTURER "WEMOS" #define DEVICE "D1_MINI_RELAYSHIELD" // Buttons // No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems #define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND, // it's the same as using a Wemos one button shield #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LED #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // When Wemos relay shield is connected GPIO5 (D1) is used for relay, // so I2C must be remapped to other pins #define I2C_SDA_PIN 12 // D6 #define I2C_SCL_PIN 14 // D5 #elif defined(WEMOS_D1_TARPUNA_SHIELD) // Info #define MANUFACTURER "WEMOS" #define DEVICE "D1_TARPUNA_SHIELD" // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define DHT_SUPPORT 1 #define DHT_PIN 12 // ----------------------------------------------------------------------------- // ESPurna // ----------------------------------------------------------------------------- #elif defined(TINKERMAN_ESPURNA_H06) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_H06" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Normal pushbutton #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_INVERSE // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 2 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(TINKERMAN_ESPURNA_H08) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_H08" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Normal pushbutton #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 5 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(TINKERMAN_ESPURNA_SWITCH) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "ESPURNA_SWITCH" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 // Touch button #define BUTTON1_CONFIG BUTTON_PUSHBUTTON #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_INVERSE // Check http://tinkerman.cat/rfm69-wifi-gateway/ #elif defined(TINKERMAN_RFM69GW) // Info #define MANUFACTURER "TINKERMAN" #define DEVICE "RFM69GW" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // RFM69GW #define RFM69_SUPPORT 1 // Disable non-core modules #define ALEXA_SUPPORT 0 #define DOMOTICZ_SUPPORT 0 #define HOMEASSISTANT_SUPPORT 0 #define I2C_SUPPORT 0 #define SCHEDULER_SUPPORT 0 #define SENSOR_SUPPORT 0 #define THINGSPEAK_SUPPORT 0 // ----------------------------------------------------------------------------- // Itead Studio boards // ----------------------------------------------------------------------------- #elif defined(ITEAD_SONOFF_BASIC) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_BASIC" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 14 #define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON2_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_RF) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_RF" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 14 #define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON2_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_MINI) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_MINI" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 4 #define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON2_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_TH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_TH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Jack is connected to GPIO14 (and with a small hack to GPIO4) #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 14 #ifndef DHT_SUPPORT #define DHT_SUPPORT 1 #endif #define DHT_PIN 14 #define DHT_TYPE DHT_CHIP_SI7021 //#define I2C_SDA_PIN 4 //#define I2C_SCL_PIN 14 #elif defined(ITEAD_SONOFF_SV) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_SV" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SLAMPHER) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SLAMPHER" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_S20) // Info #define MANUFACTURER "ITEAD" #define DEVICE "S20" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_TOUCH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_TOUCH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_POW) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_POW" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 15 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 5 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 14 #elif defined(ITEAD_SONOFF_POW_R2) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_POW_R2" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Disable UART noise #define DEBUG_SERIAL_SUPPORT 0 // CSE7766 #ifndef CSE7766_SUPPORT #define CSE7766_SUPPORT 1 #endif #define CSE7766_PIN 1 #elif defined(ITEAD_SONOFF_DUAL) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_DUAL" #define SERIAL_BAUDRATE 19230 #define RELAY_PROVIDER RELAY_PROVIDER_DUAL #define DUMMY_RELAY_COUNT 2 #define DEBUG_SERIAL_SUPPORT 0 // Buttons #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 1 #define BUTTON_EVENTS_SOURCE BUTTON_EVENTS_SOURCE_ITEAD_SONOFF_DUAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_DUAL_R2) #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_DUAL_R2" // Buttons #define BUTTON1_PIN 0 // Button 0 on header #define BUTTON2_PIN 9 // Button 1 on header #define BUTTON3_PIN 10 // Physical button #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 1 #define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_4CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_4CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON4_PIN 14 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON4_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 #define BUTTON4_RELAY 4 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_4CH_PRO) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_4CH_PRO" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON4_PIN 14 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON4_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 #define BUTTON4_RELAY 4 // Sonoff 4CH Pro uses a secondary STM32 microcontroller to handle // buttons and relays, but it also forwards button presses to the ESP8285. // This allows ESPurna to handle button presses -almost- the same way // as with other devices except: // * Double click seems to break/disable the button on the STM32 side // * With S6 switch to 1 (self-locking and inching modes) everything's OK // * With S6 switch to 0 (interlock mode) if there is a relay ON // and you click on another relay button, the STM32 sends a "press" // event for the button of the first relay (to turn it OFF) but it // does not send a "release" event. It's like it's holding the // button down since you can see it is still LOW. // Whatever reason the result is that it may actually perform a // long click or long-long click. // The configuration below make the button toggle the relay on press events // and disables any possibly harmful combination with S6 set to 0. // If you are sure you will only use S6 to 1 you can comment the // BUTTON1_LNGCLICK and BUTTON1_LNGLNGCLICK options below to recover the // reset mode and factory reset functionalities, or link other actions like // AP mode in the commented line below. #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE //#define BUTTON1_LNGCLICK BUTTON_ACTION_AP #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE #define BUTTON2_PRESS BUTTON_ACTION_TOGGLE #define BUTTON2_CLICK BUTTON_ACTION_NONE #define BUTTON3_PRESS BUTTON_ACTION_TOGGLE #define BUTTON3_CLICK BUTTON_ACTION_NONE #define BUTTON4_PRESS BUTTON_ACTION_TOGGLE #define BUTTON4_CLICK BUTTON_ACTION_NONE // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_1CH_INCHING) // The inching functionality is managed by a misterious IC in the board. // You cannot control the inching button and functionality from the ESP8266 // Besides, enabling the inching functionality using the hardware button // will result in the relay switching on and off continuously. // Fortunately the unkown IC keeps memory of the hardware inching status // so you can just disable it and forget. The inching LED must be lit. // You can still use the pulse options from the web interface // without problem. // Info #define MANUFACTURER "ITEAD" #define DEVICE "1CH_INCHING" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_MOTOR) // Info #define MANUFACTURER "ITEAD" #define DEVICE "MOTOR" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_BNSZ01) // Info #define MANUFACTURER "ITEAD" #define DEVICE "BNSZ01" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 1 #define LIGHT_CH1_PIN 12 #define LIGHT_CH1_INVERSE 0 #elif defined(ITEAD_SONOFF_RFBRIDGE) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_RFBRIDGE" #define RELAY_PROVIDER RELAY_PROVIDER_RFBRIDGE // Number of virtual switches #ifndef DUMMY_RELAY_COUNT #define DUMMY_RELAY_COUNT 8 #endif // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #define RF_SUPPORT 1 // Only used when RFB_DIRECT=1 #define RFB_RX_PIN 4 #define RFB_TX_PIN 5 // When using un-modified harware, ESPurna communicates with the secondary // MCU EFM8BB1 via UART at 19200 bps so we need to change the speed of // the port and remove UART noise on serial line #if not RFB_DIRECT #define SERIAL_BAUDRATE 19200 #define DEBUG_SERIAL_SUPPORT 0 #endif #elif defined(ITEAD_SONOFF_B1) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_B1" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define MY92XX_MODEL MY92XX_MODEL_MY9231 #define MY92XX_CHIPS 2 #define MY92XX_DI_PIN 12 #define MY92XX_DCKI_PIN 14 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 4, 3, 5, 0, 1 #define LIGHT_WHITE_FACTOR (0.1) // White LEDs are way more bright in the B1 #elif defined(ITEAD_SONOFF_LED) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_LED" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 12 // Cold white #define LIGHT_CH2_PIN 14 // Warm white #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #elif defined(ITEAD_SONOFF_T1_1CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_1CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_T1_2CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_2CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_ACTION_TOGGLE #define BUTTON2_CLICK BUTTON_ACTION_NONE #define BUTTON2_DBLCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_T1_3CH) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_T1_3CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_ACTION_TOGGLE #define BUTTON2_CLICK BUTTON_ACTION_NONE #define BUTTON2_DBLCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_PRESS BUTTON_ACTION_TOGGLE #define BUTTON3_CLICK BUTTON_ACTION_NONE #define BUTTON3_DBLCLICK BUTTON_ACTION_NONE #define BUTTON3_LNGCLICK BUTTON_ACTION_NONE #define BUTTON3_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_S31) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_S31" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Disable UART noise #define DEBUG_SERIAL_SUPPORT 0 // CSE7766 #define CSE7766_SUPPORT 1 #define CSE7766_PIN 1 #elif defined(ITEAD_SONOFF_S31_LITE) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_S31_LITE" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 #elif defined(ITEAD_SONOFF_IFAN02) // Info #define MANUFACTURER "ITEAD" #define DEVICE "SONOFF_IFAN02" // These are virtual buttons triggered by the remote #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON4_PIN 14 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON4_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // ORVIBO // ----------------------------------------------------------------------------- #elif defined(ORVIBO_B25) // Info #define MANUFACTURER "ORVIBO" #define DEVICE "B25" // Buttons #define BUTTON1_PIN 14 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 12 // 4 blue led #define LED1_PIN_INVERSE 1 #define LED2_PIN 4 // 12 red led #define LED2_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // YJZK // ----------------------------------------------------------------------------- #elif defined(YJZK_SWITCH_1CH) // Info #define MANUFACTURER "YJZK" #define DEVICE "SWITCH_1CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 0 #elif defined(YJZK_SWITCH_2CH) // Info #define MANUFACTURER "YJZK" #define DEVICE "SWITCH_2CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_ACTION_TOGGLE #define BUTTON2_CLICK BUTTON_ACTION_NONE #define BUTTON2_DBLCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 0 // YJZK 3CH switch // Also Lixin Touch Wifi 3M #elif defined(YJZK_SWITCH_3CH) // Info #define MANUFACTURER "YJZK" #define DEVICE "SWITCH_3CH" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 9 #define BUTTON3_PIN 10 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_ACTION_TOGGLE #define BUTTON2_CLICK BUTTON_ACTION_NONE #define BUTTON2_DBLCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_PRESS BUTTON_ACTION_TOGGLE #define BUTTON3_CLICK BUTTON_ACTION_NONE #define BUTTON3_DBLCLICK BUTTON_ACTION_NONE #define BUTTON3_LNGCLICK BUTTON_ACTION_NONE #define BUTTON3_LNGLNGCLICK BUTTON_ACTION_RESET #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 3 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 5 #define RELAY3_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Electrodragon boards // ----------------------------------------------------------------------------- #elif defined(ELECTRODRAGON_WIFI_IOT) // Info #define MANUFACTURER "ELECTRODRAGON" #define DEVICE "WIFI_IOT" // Buttons #define BUTTON1_PIN 0 #define BUTTON2_PIN 2 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 16 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // WorkChoice ecoPlug // ----------------------------------------------------------------------------- #elif defined(WORKCHOICE_ECOPLUG) // Info #define MANUFACTURER "WORKCHOICE" #define DEVICE "ECOPLUG" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // AI Thinker // ----------------------------------------------------------------------------- #elif defined(AITHINKER_AI_LIGHT) // Info #define MANUFACTURER "AITHINKER" #define DEVICE "AI_LIGHT" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 13 #define MY92XX_DCKI_PIN 15 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // Lyasi LED // ----------------------------------------------------------------------------- #elif defined(LYASI_LIGHT) // Info #define MANUFACTURER "LYASI" #define DEVICE "RGB-LED" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 4 #define MY92XX_DCKI_PIN 5 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // LED Controller // ----------------------------------------------------------------------------- #elif defined(MAGICHOME_LED_CONTROLLER) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "LED_CONTROLLER" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 13 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_RX_PIN 4 #define IR_BUTTON_SET 1 #elif defined(MAGICHOME_LED_CONTROLLER_20) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "LED_CONTROLLER_20" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_RX_PIN 4 #define IR_BUTTON_SET 1 #elif defined(MAGICHOME_ZJ_WFMN_A_11) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "ZJ_WFMN_A_11" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #define LED2_PIN 15 #define LED2_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 14 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_RX_PIN 4 #define IR_BUTTON_SET 1 #elif defined(MAGICHOME_ZJ_WFMN_B_11) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "ZJ_WFMN_B_11" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #define LED2_PIN 15 #define LED2_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 13 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // RF #define RF_SUPPORT 1 #define RFB_DIRECT 1 #define RFB_RX_PIN 4 #elif defined(MAGICHOME_ZJ_WFMN_C_11) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "ZJ_WFMN_C_11" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 1 #define LIGHT_CH1_PIN 12 // WHITE #elif defined(MAGICHOME_ZJ_ESPM_5CH_B_13) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "ZJ_ESPM_5CH_B_13" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 5 // COLD WHITE #define LIGHT_CH5_PIN 15 // WARM WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(MAGICHOME_ZJ_LB_RGBWW_L) // Info #define MANUFACTURER "MAGICHOME" #define DEVICE "ZJ_LB_RGBWW_L" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 12 // COLD WHITE #define LIGHT_CH5_PIN 13 // WARM WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 // ----------------------------------------------------------------------------- // HUACANXING H801 & H802 // ----------------------------------------------------------------------------- #elif defined(HUACANXING_H801) // Info #define MANUFACTURER "HUACANXING" #define DEVICE "H801" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define DEBUG_PORT Serial1 #define SERIAL_RX_ENABLED 1 // LEDs #define LED1_PIN 5 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 15 // RED #define LIGHT_CH2_PIN 13 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 14 // WHITE1 #define LIGHT_CH5_PIN 4 // WHITE2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(HUACANXING_H802) // Info #define MANUFACTURER "HUACANXING" #define DEVICE "H802" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define DEBUG_PORT Serial1 #define SERIAL_RX_ENABLED 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 14 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Jan Goedeke Wifi Relay // https://github.com/JanGoe/esp8266-wifi-relay // ----------------------------------------------------------------------------- #elif defined(JANGOE_WIFI_RELAY_NC) // Info #define MANUFACTURER "JANGOE" #define DEVICE "WIFI_RELAY_NC" // Buttons #define BUTTON1_PIN 12 #define BUTTON2_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 2 #define RELAY2_PIN 14 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_TYPE RELAY_TYPE_INVERSE #elif defined(JANGOE_WIFI_RELAY_NO) // Info #define MANUFACTURER "JANGOE" #define DEVICE "WIFI_RELAY_NO" // Buttons #define BUTTON1_PIN 12 #define BUTTON2_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 2 #define RELAY2_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // Jorge García Wifi+Relays Board Kit // https://www.tindie.com/products/jorgegarciadev/wifi--relays-board-kit // https://github.com/jorgegarciadev/wifikit // ----------------------------------------------------------------------------- #elif defined(JORGEGARCIA_WIFI_RELAYS) // Info #define MANUFACTURER "JORGEGARCIA" #define DEVICE "WIFI_RELAYS" // Relays #define RELAY1_PIN 0 #define RELAY2_PIN 2 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_TYPE RELAY_TYPE_INVERSE // ----------------------------------------------------------------------------- // WiFi MQTT Relay / Thermostat // ----------------------------------------------------------------------------- #elif defined(OPENENERGYMONITOR_MQTT_RELAY) // Info #define MANUFACTURER "OPENENERGYMONITOR" #define DEVICE "MQTT_RELAY" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 16 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // WiOn 50055 Indoor Wi-Fi Wall Outlet & Tap // https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50050-Indoor-Wi-Fi-Outlet-Wireless-Switch-Programmable-Timer-%2F263112281551 // https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50055-Indoor-Wi-Fi-Wall-Tap-Monitor-Energy-Usage-Wireless-Smart-Switch-%2F263020837777 // ----------------------------------------------------------------------------- #elif defined(WION_50055) // Currently untested, does not support energy monitoring // Info #define MANUFACTURER "WION" #define DEVICE "50055" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // EX-Store Wifi Relay v3.1 // https://ex-store.de/ESP8266-WiFi-Relay-V31 // ----------------------------------------------------------------------------- #elif defined(EXS_WIFI_RELAY_V31) // Untested // Info #define MANUFACTURER "EXS" #define DEVICE "WIFI_RELAY_V31" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 13 #define RELAY1_TYPE RELAY_TYPE_LATCHED #define RELAY1_RESET_PIN 12 // ----------------------------------------------------------------------------- // EX-Store Wifi Relay v5.0 // ----------------------------------------------------------------------------- #elif defined(EXS_WIFI_RELAY_V50) // Info #define MANUFACTURER "EXS" #define DEVICE "WIFI_RELAY_V50" // Buttons #define BUTTON1_PIN 5 #define BUTTON2_PIN 4 #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP #define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_LATCHED #define RELAY1_RESET_PIN 16 #define RELAY2_PIN 13 #define RELAY2_TYPE RELAY_TYPE_LATCHED #define RELAY2_RESET_PIN 12 // LEDs #define LED1_PIN 15 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // V9261F // ----------------------------------------------------------------------------- #elif defined(GENERIC_V9261F) // Info #define MANUFACTURER "GENERIC" #define DEVICE "V9261F" #define ALEXA_SUPPORT 0 // V9261F #define V9261F_SUPPORT 1 #define V9261F_PIN 2 #define V9261F_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // ECH1560 // ----------------------------------------------------------------------------- #elif defined(GENERIC_ECH1560) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ECH1560" #define ALEXA_SUPPORT 0 // ECH1560 #define ECH1560_SUPPORT 1 #define ECH1560_CLK_PIN 4 #define ECH1560_MISO_PIN 5 #define ECH1560_INVERTED 0 // ----------------------------------------------------------------------------- // ESPLive // https://github.com/ManCaveMade/ESP-Live // ----------------------------------------------------------------------------- #elif defined(MANCAVEMADE_ESPLIVE) // Info #define MANUFACTURER "MANCAVEMADE" #define DEVICE "ESPLIVE" // Buttons #define BUTTON1_PIN 4 #define BUTTON2_PIN 5 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // DS18B20 #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 2 #define DALLAS_UPDATE_INTERVAL 5000 #define TEMPERATURE_MIN_CHANGE 1.0 // ----------------------------------------------------------------------------- // QuinLED // http://blog.quindorian.org/2017/02/esp8266-led-lighting-quinled-v2-6-pcb.html // ----------------------------------------------------------------------------- #elif defined(INTERMITTECH_QUINLED) // Info #define MANUFACTURER "INTERMITTECH" #define DEVICE "QUINLED" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 5 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 0 #define LIGHT_CH2_PIN 2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 // ----------------------------------------------------------------------------- // Arilux AL-LC06 // ----------------------------------------------------------------------------- #elif defined(ARILUX_AL_LC01) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC01" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 3 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #elif defined(ARILUX_AL_LC02) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC02" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #elif defined(ARILUX_AL_LC02_V14) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC02_V14" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 13 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #elif defined(ARILUX_AL_LC06) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC06" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 15 // WHITE1 #define LIGHT_CH5_PIN 5 // WHITE2 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(ARILUX_AL_LC11) // Info #define MANUFACTURER "ARILUX" #define DEVICE "AL_LC11" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 13 // WHITE1 #define LIGHT_CH5_PIN 12 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 #elif defined(ARILUX_E27) // Info #define MANUFACTURER "ARILUX" #define DEVICE "E27" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 13 #define MY92XX_DCKI_PIN 15 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // XENON SM-PW701U // ----------------------------------------------------------------------------- #elif defined(XENON_SM_PW702U) // Info #define MANUFACTURER "XENON" #define DEVICE "SM_PW702U" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // ISELECTOR SM-PW702 // ----------------------------------------------------------------------------- #elif defined(ISELECTOR_SM_PW702) // Info #define MANUFACTURER "ISELECTOR" #define DEVICE "SM_PW702" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 //BLUE #define LED1_PIN_INVERSE 0 #define LED2_PIN 5 //RED #define LED2_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // AUTHOMETION LYT8266 // https://authometion.com/shop/en/home/13-lyt8266.html // ----------------------------------------------------------------------------- #elif defined(AUTHOMETION_LYT8266) // Info #define MANUFACTURER "AUTHOMETION" #define DEVICE "LYT8266" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 13 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 2 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_ENABLE_PIN 15 #elif defined(GIZWITS_WITTY_CLOUD) // Info #define MANUFACTURER "GIZWITS" #define DEVICE "WITTY_CLOUD" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Buttons #define BUTTON1_PIN 4 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET #define ANALOG_SUPPORT 1 // LEDs #define LED1_PIN 2 // BLUE build-in #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 3 #define LIGHT_CH1_PIN 15 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 // ----------------------------------------------------------------------------- // KMC 70011 // https://www.amazon.com/KMC-Monitoring-Required-Control-Compatible/dp/B07313TH7B // ----------------------------------------------------------------------------- #elif defined(KMC_70011) // Info #define MANUFACTURER "KMC" #define DEVICE "70011" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor // ----------------------------------------------------------------------------- // Euromate (?) Wifi Stecker Schuko // https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko/p/2291706 // Thanks to @Geitde // ----------------------------------------------------------------------------- #elif defined(EUROMATE_WIFI_STECKER_SCHUKO) // Info #define MANUFACTURER "EUROMATE" #define DEVICE "WIFI_STECKER_SCHUKO" // Buttons #define BUTTON1_PIN 14 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // The relay in the device is not a bistable (latched) relay. // The device is reported to have a flip-flop circuit to drive the relay // So @Geitde hack is still the only possible // Hack: drive GPIO12 low and use GPIO5 as normal relay pin: #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define LED2_PIN 12 /* DUMMY: exploit default off state for GPIO12=low */ #define LED2_PIN_INVERSE 0 // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Euromate (?) Wifi Stecker Schuko Version 2 // This configuration is for the second generation of devices sold by OBI. // https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko-weiss/p/4077806 // ----------------------------------------------------------------------------- #elif defined(EUROMATE_WIFI_STECKER_SCHUKO_V2) // Info #define MANUFACTURER "EUROMATE" #define DEVICE "WIFI_STECKER_SCHUKO_V2" // Buttons #define BUTTON1_PIN 5 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL // Green #define LED1_PIN 12 #define LED1_MODE LED_MODE_WIFI #define LED1_PIN_INVERSE 0 // Red #define LED2_PIN 13 #define LED2_MODE LED_MODE_RELAY #define LED2_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Generic 8CH // ----------------------------------------------------------------------------- #elif defined(GENERIC_8CH) // Info #define MANUFACTURER "GENERIC" #define DEVICE "8CH" // Relays #define RELAY1_PIN 0 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 2 #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_PIN 4 #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_PIN 5 #define RELAY4_TYPE RELAY_TYPE_NORMAL #define RELAY5_PIN 12 #define RELAY5_TYPE RELAY_TYPE_NORMAL #define RELAY6_PIN 13 #define RELAY6_TYPE RELAY_TYPE_NORMAL #define RELAY7_PIN 14 #define RELAY7_TYPE RELAY_TYPE_NORMAL #define RELAY8_PIN 15 #define RELAY8_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // STM RELAY // ----------------------------------------------------------------------------- #elif defined(STM_RELAY) // Info #define MANUFACTURER "STM_RELAY" #define DEVICE "2CH" // Relays #define DUMMY_RELAY_COUNT 2 #define RELAY_PROVIDER RELAY_PROVIDER_STM // Remove UART noise on serial line #define DEBUG_SERIAL_SUPPORT 0 // ----------------------------------------------------------------------------- // Tonbux Powerstrip02 // ----------------------------------------------------------------------------- #elif defined(TONBUX_POWERSTRIP02) // Info #define MANUFACTURER "TONBUX" #define DEVICE "POWERSTRIP02" // Buttons #define BUTTON1_PIN 5 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 0 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_INVERSE #define RELAY2_PIN 13 #define RELAY2_TYPE RELAY_TYPE_INVERSE #define RELAY3_PIN 12 #define RELAY3_TYPE RELAY_TYPE_INVERSE #define RELAY4_PIN 14 #define RELAY4_TYPE RELAY_TYPE_INVERSE // Not a relay. USB ports on/off #define RELAY5_PIN 16 #define RELAY5_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // 1 blue led #define LED1_PIN_INVERSE 1 #define LED2_PIN 3 // 3 red leds #define LED2_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Lingan SWA1 // ----------------------------------------------------------------------------- #elif defined(LINGAN_SWA1) // Info #define MANUFACTURER "LINGAN" #define DEVICE "SWA1" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // HEYGO HY02 // ----------------------------------------------------------------------------- #elif defined(HEYGO_HY02) // Info #define MANUFACTURER "HEYGO" #define DEVICE "HY02" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Maxcio W-US002S // ----------------------------------------------------------------------------- #elif defined(MAXCIO_WUS002S) // Info #define MANUFACTURER "MAXCIO" #define DEVICE "WUS002S" // Buttons #define BUTTON1_PIN 2 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 13 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 3 #define LED1_PIN_INVERSE 0 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_CURRENT_R 0.002 // Current resistor #define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor // LED1 on RX pin #define DEBUG_SERIAL_SUPPORT 1 // ----------------------------------------------------------------------------- // Maxcio W-DE004 // ----------------------------------------------------------------------------- #elif defined(MAXCIO_WDE004) // Info #define MANUFACTURER "MAXCIO" #define DEVICE "WDE004" // Buttons #define BUTTON1_PIN 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Maxcio W-UK007S // Like this: https://www.amazon.co.uk/Maxcio-Monitoring-Function-Compatible-Required/dp/B07BWFB55Q/ref=pd_rhf_se_p_img_2?_encoding=UTF8&psc=1&refRID=4H63A43SKHV8WV54XH19 // ----------------------------------------------------------------------------- #elif defined(MAXCIO_WUK007S) // Info #define MANUFACTURER "MAXCIO" #define DEVICE "WUK007S" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 #define LED1_PIN_INVERSE 0 #define LED1_RELAY 1 #define LED1_MODE LED_MODE_RELAY_WIFI // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 24380 #define HLW8012_VOLTAGE_RATIO 32048 #define HLW8012_POWER_RATIO 3509285 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // Oukitel P1 Smart Plug // https://www.amazon.com/Docooler-OUKITEL-Control-Wireless-Adaptor/dp/B07J3BYFJX/ref=sr_1_fkmrnull_2?keywords=oukitel+p1+smart+switch&qid=1550424399&s=gateway&sr=8-2-fkmrnull // ----------------------------------------------------------------------------- #elif defined(OUKITEL_P1) // Info #define MANUFACTURER "Oukitel" #define DEVICE "P1" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays // Right #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // Left #define RELAY2_PIN 15 #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // blue #define LED1_PIN_INVERSE 1 #define LED1_MODE LED_MODE_WIFI // ----------------------------------------------------------------------------- // YiDian XS-SSA05 // ----------------------------------------------------------------------------- #elif defined(YIDIAN_XSSSA05) // Info #define MANUFACTURER "YIDIAN" #define DEVICE "XSSSA05" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // red #define LED1_PIN_INVERSE 1 #define LED1_MODE LED_MODE_WIFI #define LED2_PIN 15 // blue #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_RELAY // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 3 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // TONBUX XS-SSA01 // ----------------------------------------------------------------------------- #elif defined(TONBUX_XSSSA01) // Info #define MANUFACTURER "TONBUX" #define DEVICE "XSSSA01" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // TONBUX XS-SSA06 // ----------------------------------------------------------------------------- #elif defined(TONBUX_XSSSA06) // Info #define MANUFACTURER "TONBUX" #define DEVICE "XSSSA06" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // R - 8 rgb led ring #define LED1_PIN_INVERSE 0 #define LED2_PIN 5 // G #define LED2_PIN_INVERSE 0 #define LED3_PIN 2 // B #define LED3_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // GREEN ESP8266 RELAY MODULE // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180323113846&SearchText=Green+ESP8266 // ----------------------------------------------------------------------------- #elif defined(GREEN_ESP8266RELAY) // Info #define MANUFACTURER "GREEN" #define DEVICE "ESP8266RELAY" // Buttons // Not a button but input via Optocoupler #define BUTTON1_PIN 5 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Henrique Gravina ESPIKE // https://github.com/Henriquegravina/Espike // ----------------------------------------------------------------------------- #elif defined(IKE_ESPIKE) #define MANUFACTURER "IKE" #define DEVICE "ESPIKE" #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_PIN 13 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PIN 12 #define BUTTON2_RELAY 2 #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_PIN 14 #define BUTTON3_RELAY 3 #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 5 #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_PIN 16 #define RELAY3_TYPE RELAY_TYPE_NORMAL #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // SWIFITCH // https://github.com/ArnieX/swifitch // ----------------------------------------------------------------------------- #elif defined(ARNIEX_SWIFITCH) // Info #define MANUFACTURER "ARNIEX" #define DEVICE "SWIFITCH" // Buttons #define BUTTON1_PIN 4 // D2 #define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON1_PRESS BUTTON_ACTION_NONE #define BUTTON1_CLICK BUTTON_ACTION_TOGGLE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE // Relays #define RELAY1_PIN 5 // D1 #define RELAY1_TYPE RELAY_TYPE_INVERSE // LEDs #define LED1_PIN 12 // D6 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // ESP-01S RELAY v4.0 // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404024035&SearchText=esp-01s+relay // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_RELAY_V40) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_RELAY_40" // Relays #define RELAY1_PIN 0 #ifndef RELAY1_TYPE #define RELAY1_TYPE RELAY_TYPE_NORMAL // See #1504 and #1554 #endif // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // ESP-01S RGB LED v1.0 (some sold with ws2818) // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180404023816&SearchText=esp-01s+led+controller // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_RGBLED_V10) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_RGBLED_10" // This board is sold as RGB LED module BUT it has on board 3 pin ph2.0 connector (VCC, GPIO2, GND) // so, if you wish, you may connect LED, BUTTON, RELAY, SENSOR etc. // Buttons //#define BUTTON1_PIN 2 // Relays //#define RELAY1_PIN 2 // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // ESP-01S DHT11 v1.0 // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180410105907&SearchText=esp-01s+dht11 // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_DHT11_V10) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_DHT11_10" // DHT11 #ifndef DHT_SUPPORT #define DHT_SUPPORT 1 #endif #define DHT_PIN 2 #define DHT_TYPE DHT_CHIP_DHT11 // ----------------------------------------------------------------------------- // ESP-01S DS18B20 v1.0 // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180410105933&SearchText=esp-01s+ds18b20 // ----------------------------------------------------------------------------- #elif defined(GENERIC_ESP01S_DS18B20_V10) // Info #define MANUFACTURER "GENERIC" #define DEVICE "ESP01S_DS18B20_10" // DB18B20 #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 2 // ----------------------------------------------------------------------------- // ESP-DIN relay board V1 // https://github.com/pilotak/esp_din // ----------------------------------------------------------------------------- #elif defined(PILOTAK_ESP_DIN_V1) // Info #define MANUFACTURER "PILOTAK" #define DEVICE "ESP_DIN_V1" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 5 #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 15 #define LED1_PIN_INVERSE 0 #define I2C_SDA_PIN 12 #define I2C_SCL_PIN 13 #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 1 #endif #define DALLAS_PIN 2 #define RF_SUPPORT 1 #define RFB_DIRECT 1 #define RFB_RX_PIN 14 #ifndef DIGITAL_SUPPORT #define DIGITAL_SUPPORT 1 #endif #define DIGITAL1_PIN 16 #define DIGITAL1_PIN_MODE INPUT #define DIGITAL1_DEFAULT_STATE 0 // ----------------------------------------------------------------------------- // Heltec Touch Relay // https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180408043114&SearchText=esp8266+touch+relay // ----------------------------------------------------------------------------- #elif defined(HELTEC_TOUCHRELAY) // Info #define MANUFACTURER "HELTEC" #define DEVICE "TOUCH_RELAY" // Buttons #define BUTTON1_PIN 14 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // Zhilde ZLD-EU44-W // http://www.zhilde.com/product/60705150109-805652505/EU_WiFi_Surge_Protector_Extension_Socket_4_Outlets_works_with_Amazon_Echo_Smart_Power_Strip.html // ----------------------------------------------------------------------------- #elif defined(ZHILDE_EU44_W) // Info #define MANUFACTURER "ZHILDE" #define DEVICE "EU44_W" // Based on the reporter, this product uses GPIO1 and 3 for the button // and onboard LED, so hardware serial should be disabled... #define DEBUG_SERIAL_SUPPORT 0 // Buttons #define BUTTON1_PIN 3 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Relays #define RELAY1_PIN 5 #define RELAY2_PIN 4 #define RELAY3_PIN 12 #define RELAY4_PIN 13 #define RELAY5_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL #define RELAY5_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 1 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Allnet 4duino ESP8266-UP-Relais // http://www.allnet.de/de/allnet-brand/produkte/neuheiten/p/allnet-4duino-iot-wlan-relais-unterputz-esp8266-up-relais/ // https://shop.allnet.de/fileadmin/transfer/products/148814.pdf // ----------------------------------------------------------------------------- #elif defined(ALLNET_4DUINO_IOT_WLAN_RELAIS) // Info #define MANUFACTURER "ALLNET" #define DEVICE "4DUINO_IOT_WLAN_RELAIS" // Relays #define RELAY1_PIN 14 #define RELAY1_RESET_PIN 12 #define RELAY1_TYPE RELAY_TYPE_LATCHED // LEDs #define LED1_PIN 0 #define LED1_PIN_INVERSE 1 // Buttons //#define BUTTON1_PIN 0 //#define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH // Using pins labelled as SDA & SCL as buttons #define BUTTON2_PIN 4 #define BUTTON2_CONFIG BUTTON_PUSHBUTTON #define BUTTON2_PRESS BUTTON_ACTION_TOGGLE #define BUTTON2_CLICK BUTTON_ACTION_NONE #define BUTTON2_DBLCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_NONE #define BUTTON3_PIN 5 #define BUTTON3_CONFIG BUTTON_PUSHBUTTON // Using pins labelled as SDA & SCL for I2C //#define I2C_SDA_PIN 4 //#define I2C_SCL_PIN 5 // ----------------------------------------------------------------------------- // Luani HVIO // https://luani.de/projekte/esp8266-hvio/ // https://luani.de/blog/esp8266-230v-io-modul/ // ----------------------------------------------------------------------------- #elif defined(LUANI_HVIO) // Info #define MANUFACTURER "LUANI" #define DEVICE "HVIO" // Buttons #define BUTTON1_PIN 12 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_HIGH //Hardware Pullup #define BUTTON1_PRESS BUTTON_ACTION_NONE #define BUTTON1_CLICK BUTTON_ACTION_TOGGLE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE #define BUTTON2_PIN 13 #define BUTTON2_RELAY 2 #define BUTTON2_CONFIG BUTTON_SWITCH | BUTTON_DEFAULT_HIGH //Hardware Pullup #define BUTTON2_CLICK BUTTON_ACTION_TOGGLE // Relays #define RELAY1_PIN 4 #define RELAY2_PIN 5 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 15 #define LED1_PIN_INVERSE 0 // ----------------------------------------------------------------------------- // Tonbux 50-100M Smart Mosquito Killer USB // https://www.aliexpress.com/item/Original-Tonbux-50-100M-Smart-Mosquito-Killer-USB-Plug-No-Noise-Repellent-App-Smart-Module/32859330820.html // ----------------------------------------------------------------------------- #elif defined(TONBUX_MOSQUITO_KILLER) // Info #define MANUFACTURER "TONBUX" #define DEVICE "MOSQUITO_KILLER" // Buttons #define BUTTON1_PIN 2 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 5 // not a relay, fan #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 15 // blue led #define LED1_PIN_INVERSE 1 #define LED1_MODE LED_MODE_WIFI #define LED2_PIN 14 // red led #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_RELAY #define LED3_PIN 12 // UV leds (1-2-3-4-5-6-7-8) #define LED3_PIN_INVERSE 0 #define LED3_RELAY 1 #define LED4_PIN 16 // UV leds (9-10-11) #define LED4_PIN_INVERSE 0 #define LED4_RELAY 1 // ----------------------------------------------------------------------------- // Avatto NAS-WR01W Wifi Smart Power Plug // https://www.aliexpress.com/item/33011753732.html // https://todo... // ----------------------------------------------------------------------------- #elif defined(AVATTO_NAS_WR01W) // Info #define MANUFACTURER "AVATTO" #define DEVICE "NAS_WR01W" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // NEO Coolcam NAS-WR01W Wifi Smart Power Plug // https://es.aliexpress.com/item/-/32854589733.html?spm=a219c.12010608.0.0.6d084e68xX0y5N // https://www.fasttech.com/product/9649426-neo-coolcam-nas-wr01w-wifi-smart-power-plug-eu // ----------------------------------------------------------------------------- #elif defined(NEO_COOLCAM_NAS_WR01W) // Info #define MANUFACTURER "NEO_COOLCAM" #define DEVICE "NAS_WR01W" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Deltaco SH_P01 Wifi Smart Power Plug // ----------------------------------------------------------------------------- #elif defined(DELTACO_SH_P01) // Info #define MANUFACTURER "DELTACO" #define DEVICE "SH_P01" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 5 #define LED1_PIN_INVERSE 1 #define LED1_MODE LED_MODE_FINDME // ------------------------------------------------------------------------------ // DELTACO_SH_P03USB Wifi Smart Power Plug // ----------------------------------------------------------------------------- #elif defined(DELTACO_SH_P03USB) // Info #define MANUFACTURER "DELTACO" #define DEVICE "SH_P03USB" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP #define BUTTON1_RELAY 2 // Relays #define RELAY1_PIN 15 // USB power #define RELAY2_PIN 12 // power plug 1 #define RELAY3_PIN 14 // power plug 2 #define RELAY4_PIN 5 // power plug 3 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // power led #define LED1_PIN_INVERSE 1 #define LED1_MODE LED_MODE_FINDME // ------------------------------------------------------------------------------ // Fornorm Wi-Fi USB Extension Socket (ZLD-34EU) // https://www.aliexpress.com/item/Fornorm-WiFi-Extension-Socket-with-Surge-Protector-Smart-Power-Strip-3-Outlets-and-4-USB-Charging/32849743948.html // Also: Estink Wifi Power Strip // ----------------------------------------------------------------------------- #elif defined(FORNORM_ZLD_34EU) // Info #define MANUFACTURER "FORNORM" #define DEVICE "ZLD_34EU" // Disable UART noise since this board uses GPIO3 #define DEBUG_SERIAL_SUPPORT 0 // Buttons #define BUTTON1_PIN 16 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 4 // Relays #define RELAY1_PIN 14 // USB power #define RELAY2_PIN 13 // power plug 1 #define RELAY3_PIN 4 // power plug 2 #define RELAY4_PIN 15 // power plug 3 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 // power led #define LED2_PIN 12 // power plug 1 #define LED3_PIN 3 // power plug 2 #define LED4_PIN 5 // power plug 3 #define LED1_PIN_INVERSE 1 #define LED2_PIN_INVERSE 1 #define LED3_PIN_INVERSE 1 #define LED4_PIN_INVERSE 1 #define LED1_MODE LED_MODE_FINDME #define LED2_MODE LED_MODE_FOLLOW #define LED3_MODE LED_MODE_FOLLOW #define LED4_MODE LED_MODE_FOLLOW #define LED2_RELAY 2 #define LED3_RELAY 3 #define LED4_RELAY 4 // ----------------------------------------------------------------------------- // Bruno Horta's OnOfre // https://www.bhonofre.pt/ // https://github.com/brunohorta82/BH_OnOfre/ // ----------------------------------------------------------------------------- #elif defined(BH_ONOFRE) // Info #define MANUFACTURER "BH" #define DEVICE "ONOFRE" // Buttons #define BUTTON1_PIN 12 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP #define BUTTON1_RELAY 1 #define BUTTON2_PIN 13 #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 5 #define RELAY2_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- // BlitzWolf SHP2 and SHP6 // Also several boards under different names uing a power chip labelled BL0937 or HJL-01 // * Blitzwolf (https://www.amazon.es/Inteligente-Temporización-Dispositivos-Cualquier-BlitzWolf/dp/B07BMQP142) // * HomeCube (https://www.amazon.de/Steckdose-Homecube-intelligente-Verbrauchsanzeige-funktioniert/dp/B076Q2LKHG) // * Coosa (https://www.amazon.com/COOSA-Monitoring-Function-Campatible-Assiatant/dp/B0788W9TDR) // * Gosund (http://www.gosund.com/?m=content&c=index&a=show&catid=6&id=5) // * Ablue (https://www.amazon.de/Intelligente-Steckdose-Ablue-Funktioniert-Assistant/dp/B076DRFRZC) // * DIY Tech Smart Home (https://www.amazon.es/gp/product/B07HHKXYS9) // ----------------------------------------------------------------------------- #elif defined(BLITZWOLF_BWSHPX) // Info #define MANUFACTURER "BLITZWOLF" #define DEVICE "BWSHPX" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #define LED2_PIN 0 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_FINDME #define LED2_RELAY 1 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // Same as the above but new board version marked V2.3 // BlitzWolf SHP2 V2.3 // Gosund SP1 V2.3 // ----------------------------------------------------------------------------- #elif defined(BLITZWOLF_BWSHPX_V23) // Info #define MANUFACTURER "BLITZWOLF" #define DEVICE "BWSHPX_V23" // Buttons #define BUTTON1_PIN 3 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 1 #define LED1_PIN_INVERSE 1 #define LED2_PIN 13 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_FINDME #define LED2_RELAY 1 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // BUTTON1 and LED1 are using Serial pins #define DEBUG_SERIAL_SUPPORT 0 // ----------------------------------------------------------------------------- // Similar to both devices above but also with switchable USB ports // and other sensor (CSE7766). // the pin layout is different to the above two versions // BlitzWolf SHP5 // ----------------------------------------------------------------------------- #elif defined(BLITZWOLF_BWSHP5) // Info #define MANUFACTURER "BLITZWOLF" #define DEVICE "BWSHP5" // Buttons #define BUTTON1_PIN 16 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays // Power plug #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // USB #define RELAY2_PIN 5 #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #define LED2_PIN 0 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_FINDME #define LED2_RELAY 1 // Disable UART noise #define DEBUG_SERIAL_SUPPORT 0 // CSE7766 #ifndef CSE7766_SUPPORT #define CSE7766_SUPPORT 1 #endif #define CSE7766_PIN 1 // ----------------------------------------------------------------------------- // Teckin SP21 // ----------------------------------------------------------------------------- #elif defined(TECKIN_SP21) // Info #define MANUFACTURER "TECKIN" #define DEVICE "SP21" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Teckin SP22 v1.4 - v1.6 // ----------------------------------------------------------------------------- #elif defined(TECKIN_SP22_V14) // Info #define MANUFACTURER "TECKIN" #define DEVICE "SP22_V14" // Buttons #define BUTTON1_PIN 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 3 #define LED1_PIN_INVERSE 1 #define LED2_PIN 13 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_FINDME #define LED2_RELAY 1 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 20730 #define HLW8012_VOLTAGE_RATIO 264935 #define HLW8012_POWER_RATIO 2533110 #define HLW8012_INTERRUPT_ON FALLING // BUTTON1 and LED1 are using Serial pins #define DEBUG_SERIAL_SUPPORT 0 // ----------------------------------------------------------------------------- // Teckin SP22 v1.4 - v1.6 // // NB Notes suggest that energy monitoring is removed from later versions // ----------------------------------------------------------------------------- #elif defined(TECKIN_SP23_V13) // Info .. NB Newer versions apparently lack energy monitor // The board revision is not indicated externally #define MANUFACTURER "TECKIN" #define DEVICE "SP23_V13" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 #define LED2_PIN 2 #define LED2_PIN_INVERSE 0 #define LED2_MODE LED_MODE_FINDME #define LED2_RELAY 1 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 23324 #define HLW8012_VOLTAGE_RATIO 324305 #define HLW8012_POWER_RATIO 3580841 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // Several boards under different names uing a power chip labelled BL0937 or HJL-01 // Also model number KS-602S // ----------------------------------------------------------------------------- #elif defined(GOSUND_WS1) // Info #define MANUFACTURER "GOSUND" #define DEVICE "WS1" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 1 #define LED1_PIN_INVERSE 1 // LED1 is using TX pin #define DEBUG_SERIAL_SUPPORT 0 // ---------------------------------------------------------------------------------------- // Homecube 16A is similar but some pins differ and it also has RGB LEDs // https://www.amazon.de/gp/product/B07D7RVF56/ref=oh_aui_detailpage_o00_s01?ie=UTF8&psc=1 // ---------------------------------------------------------------------------------------- #elif defined(HOMECUBE_16A) // Info #define MANUFACTURER "HOMECUBE" #define DEVICE "16A" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs //LED Pin 4 - ESP8266 onboard LED //Red LED: 0 //Green LED: 12 //Blue LED: 2 // Blue #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // Green #define LED2_PIN 12 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_RELAY // Red #define LED3_PIN 0 #define LED3_PIN_INVERSE 0 #define LED3_MODE LED_MODE_OFF // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 16 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // VANZAVANZU Smart Outlet Socket (based on BL0937 or HJL-01) // https://www.amazon.com/Smart-Plug-Wifi-Mini-VANZAVANZU/dp/B078PHD6S5 // ----------------------------------------------------------------------------- #elif defined(VANZAVANZU_SMART_WIFI_PLUG_MINI) // Info #define MANUFACTURER "VANZAVANZU" #define DEVICE "SMART_WIFI_PLUG_MINI" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #define LED2_PIN 0 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_FINDME #define LED2_RELAY 1 // Disable UART noise #define DEBUG_SERIAL_SUPPORT 0 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 3 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- #elif defined(GENERIC_AG_L4) // Info #define MANUFACTURER "GENERIC" #define DEVICE "AG_L4" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // button 1: "power" button #define BUTTON1_PIN 4 #define BUTTON1_RELAY 1 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_PRESS BUTTON_ACTION_TOGGLE #define BUTTON1_CLICK BUTTON_ACTION_NONE #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_RESET // button 2: "wifi" button #define BUTTON2_PIN 2 #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_PRESS BUTTON_ACTION_TOGGLE #define BUTTON2_CLICK BUTTON_ACTION_NONE #define BUTTON2_DBLCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGCLICK BUTTON_ACTION_NONE #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_NONE // LEDs #define LED1_PIN 5 // red status led #define LED1_PIN_INVERSE 0 #define LED2_PIN 16 // master light power #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_RELAY // Light #define LIGHT_CHANNELS 3 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 13 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 // ----------------------------------------------------------------------------- #elif defined(ALLTERCO_SHELLY1) // Info #define MANUFACTURER "ALLTERCO" #define DEVICE "SHELLY1" // Buttons #define BUTTON1_PIN 5 #define BUTTON1_CONFIG BUTTON_SWITCH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #elif defined(ALLTERCO_SHELLY2) // Info #define MANUFACTURER "ALLTERCO" #define DEVICE "SHELLY2" // Buttons #define BUTTON1_PIN 12 #define BUTTON2_PIN 14 #define BUTTON1_CONFIG BUTTON_SWITCH #define BUTTON2_CONFIG BUTTON_SWITCH #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 5 #define RELAY2_TYPE RELAY_TYPE_NORMAL #elif defined(ALLTERCO_SHELLY1PM) // Info #define MANUFACTURER "ALLTERCO" #define DEVICE "SHELLY1PM" // Buttons #define BUTTON1_PIN 4 #define BUTTON1_CONFIG BUTTON_SWITCH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 2 #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_LNGCLICK BUTTON_ACTION_RESET #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_FACTORY // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // Light #define LED1_PIN 0 #define LED1_PIN_INVERSE 1 // HJL01 / BL0937 #define HLW8012_SUPPORT 1 #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 13 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING //Temperature #define NTC_SUPPORT 1 #define SENSOR_SUPPORT 1 #define NTC_BETA 3350 #define NTC_R_UP 10000 #define NTC_R_DOWN 0 #define NTC_R0 8000 #elif defined(ALLTERCO_SHELLY25) // Info #define MANUFACTURER "ALLTERCO" #define DEVICE "SHELLY25" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_SWITCH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 5 #define BUTTON2_CONFIG BUTTON_SWITCH #define BUTTON2_RELAY 2 #define BUTTON3_PIN 2 #define BUTTON3_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON3_LNGCLICK BUTTON_ACTION_RESET #define BUTTON3_LNGLNGCLICK BUTTON_ACTION_FACTORY // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 15 #define RELAY2_TYPE RELAY_TYPE_NORMAL // Light #define LED1_PIN 0 #define LED1_PIN_INVERSE 1 //Temperature #define NTC_SUPPORT 1 #define SENSOR_SUPPORT 1 #define NTC_BETA 3350 #define NTC_R_UP 10000 #define NTC_R_DOWN 0 #define NTC_R0 8000 //Current #define ADE7953_SUPPORT 1 #define I2C_SDA_PIN 12 #define I2C_SCL_PIN 14 // ----------------------------------------------------------------------------- // also works with https://www.amazon.com/gp/product/B07TMY394G/ // see https://github.com/xoseperez/espurna/issues/2055 #elif defined(LOHAS_E27_9W) // Info #define MANUFACTURER "LOHAS" #define DEVICE "E27_9W" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define MY92XX_MODEL MY92XX_MODEL_MY9231 #define MY92XX_CHIPS 2 #define MY92XX_DI_PIN 13 #define MY92XX_DCKI_PIN 15 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT #define MY92XX_MAPPING 0, 1, 2, 3, 4 #define LIGHT_WHITE_FACTOR (0.1) // White LEDs are way more bright in the B1 // https://www.amazon.com/gp/product/B07T7W7ZMW #elif defined(LOHAS_E26_A19) // Info #define MANUFACTURER "LOHAS" #define DEVICE "E26_A19" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 14 // WHITE1 #define LIGHT_CH5_PIN 12 // WHITE1 // ----------------------------------------------------------------------------- #elif defined(TECKIN_SB53) // Info #define MANUFACTURER "TECKIN" #define DEVICE "SB53" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 4 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 13 // WARM WHITE #define LIGHT_CH5_PIN 5 // COLD WHITE // ----------------------------------------------------------------------------- #elif defined(XIAOMI_SMART_DESK_LAMP) // Info #define MANUFACTURER "XIAOMI" #define DEVICE "SMART_DESK_LAMP" // Buttons #define BUTTON1_PIN 2 #define BUTTON2_PIN 14 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP // This button doubles as switch here and as encoder mode switch below // Clicking it (for less than 500ms) will turn the light on and off // Double and Long clicks will not work as these are used to modify the encoder action #define BUTTON1_RELAY 1 #define BUTTON_LNGCLICK_DELAY 500 #define BUTTON1_DBLCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGCLICK BUTTON_ACTION_NONE #define BUTTON1_LNGLNGCLICK BUTTON_ACTION_NONE // Hidden button will enter AP mode if dblclick and reset the device when long-long-clicked #define BUTTON2_DBLCLICK BUTTON_ACTION_AP #define BUTTON2_LNGLNGCLICK BUTTON_ACTION_RESET // Light #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define LIGHT_STEP 8 #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 5 // warm white #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_PIN 4 // cold white #define LIGHT_CH2_INVERSE 0 // https://www.xiaomitoday.com/xiaomi-mijia-mjtd01yl-led-desk-lamp-review/ #define LIGHT_COLDWHITE_MIRED 153 #define LIGHT_WARMWHITE_MIRED 370 // Encoder // If mode is ENCODER_MODE_RATIO, the value ratio between both channels is changed // when the button is not pressed, and the overall brightness when pressed // If mode is ENCODER_MODE_CHANNEL, the first channel value is changed // when the button is not pressed, and the second channel when pressed // If no ENCODERX_BUTTON_PIN defined it will only change the value of the first defined channel #define ENCODER_SUPPORT 1 #define ENCODER1_PIN1 12 #define ENCODER1_PIN2 13 #define ENCODER1_BUTTON_PIN 2 // active low by default, with software pullup #define ENCODER1_CHANNEL1 0 // please note this value is 0-based (LIGHT_CH1 above) #define ENCODER1_CHANNEL2 1 // please note this value is 0-based (LIGHT_CH2 above) #define ENCODER1_MODE ENCODER_MODE_RATIO #elif defined(PHYX_ESP12_RGB) // Info #define MANUFACTURER "PHYX" #define DEVICE "ESP12_RGB" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 3 #define LIGHT_CH1_PIN 4 // RED #define LIGHT_CH2_PIN 14 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 // ----------------------------------------------------------------------------- // iWoole LED Table Lamp // http://iwoole.com/newst-led-smart-night-light-7w-smart-table-light-rgbw-wifi-app-remote-control-110v-220v-us-eu-plug-smart-lamp-google-home-decore-p00022p1.html // ----------------------------------------------------------------------------- #elif defined(IWOOLE_LED_TABLE_LAMP) // Info #define MANUFACTURER "IWOOLE" #define DEVICE "LED_TABLE_LAMP" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 5 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 4 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Generic GU10 // https://www.ebay.com/itm/1-10PC-GU10-RGB-Smart-Bulb-Wireless-WiFi-App-Remote-Ctrl-Light-for-Alexa-Google/173724116351 // ----------------------------------------------------------------------------- #elif defined(GENERIC_GU10) // Info #define MANUFACTURER "GENERIC" #define DEVICE "GU10" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 4 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Generic E14 // https://www.ebay.com/itm/LED-Bulb-Wifi-E14-4-5W-Candle-RGB-W-4in1-Dimmable-V-tac-Smart-VT-5114/163899840601 // ----------------------------------------------------------------------------- #elif defined(GENERIC_E14) // Info #define MANUFACTURER "GENERIC" #define DEVICE "E14" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 4 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 5 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Deltaco white e14 (SH-LE14W) and e27 (SH-LE27W) // ----------------------------------------------------------------------------- #elif defined(DELTACO_SH_LEXXW) // Info #define MANUFACTURER "DELTACO" #define DEVICE "SH_LEXXW" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 2 #define LIGHT_CH1_PIN 12 // WARM WHITE #define LIGHT_CH2_PIN 14 // COLD WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 // ----------------------------------------------------------------------------- // Deltaco rgbw e27 (SH-LE27RGB) // ----------------------------------------------------------------------------- #elif defined(DELTACO_SH_LEXXRGB) // Info #define MANUFACTURER "DELTACO" #define DEVICE "SH_LEXXRGB" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 14 // WARM WHITE #define LIGHT_CH5_PIN 12 // COLD WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #define LIGHT_CH5_INVERSE 0 // ----------------------------------------------------------------------------- // Nexete A19 // https://www.ebay.com/itm/Wifi-Smart-LED-light-Bulb-9W-60W-A19-850LM-RGBW-Dimmable-for-Alexa-Google-Home/283514779201 // ----------------------------------------------------------------------------- #elif defined(NEXETE_A19) // Info #define MANUFACTURER "NEXETE" #define DEVICE "A19" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 12 // RED #define LIGHT_CH2_PIN 15 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 5 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Lombex Lux Nova 2 Tunable White // https://www.amazon.com/Lombex-Compatible-Equivalent-Dimmable-2700K-6500K/dp/B07B8K72PR // ----------------------------------------------------------------------------- #elif defined(LOMBEX_LUX_NOVA2_TUNABLE_WHITE) // Info #define MANUFACTURER "LOMBEX" #define DEVICE "LUX_NOVA2_TUNABLE_WHITE" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 5 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 4 #define MY92XX_DCKI_PIN 5 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT // No RGB on this bulb. Warm white on channel 0, cool white on channel 3 #define MY92XX_MAPPING 255, 255, 255, 3, 0 // ----------------------------------------------------------------------------- // Lombex Lux Nova 2 White and Color // https://www.amazon.com/Lombex-Compatible-Equivalent-Dimmable-2700K-6500K/dp/B07B8K72PR // ----------------------------------------------------------------------------- #elif defined(LOMBEX_LUX_NOVA2_WHITE_COLOR) // Info #define MANUFACTURER "LOMBEX" #define DEVICE "LUX_NOVA2_WHITE_COLOR" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define MY92XX_MODEL MY92XX_MODEL_MY9291 #define MY92XX_CHIPS 1 #define MY92XX_DI_PIN 4 #define MY92XX_DCKI_PIN 5 #define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT // RGB on channels 0/1/2, either cool or warm white on channel 3 // The bulb *should* have cool leds, but could also have warm leds as a common defect #define MY92XX_MAPPING 0, 1, 2, 3 // ----------------------------------------------------------------------------- // Bestek Smart Plug with 2 USB ports // https://www.bestekcorp.com/bestek-smart-plug-works-with-amazon-alexa-google-assistant-and-ifttt-with-2-usb // ----------------------------------------------------------------------------- #elif defined(BESTEK_MRJ1011) // Info #define MANUFACTURER "BESTEK" #define DEVICE "MRJ1011" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relay #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LED #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // GBLIFE RGBW SOCKET // ----------------------------------------------------------------------------- #elif defined(GBLIFE_RGBW_SOCKET) // Info #define MANUFACTURER "GBLIFE" #define DEVICE "RGBW_SOCKET" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // Light RGBW #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 14 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 4 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ---------------------------------------------------------------------------------------- // Smart life Mini Smart Socket is similar Homecube 16A but some GPIOs differ // https://www.ebay.de/itm/Smart-Steckdose-WIFI-WLAN-Amazon-Alexa-Fernbedienung-Home-Socket-Zeitschaltuh-DE/123352026749?hash=item1cb85a8e7d:g:IasAAOSwk6dbj390 // Also labeled NETVIP // https://www.amazon.es/Inteligente-NETVIP-Inal%C3%A1mbrico-Interruptor-Funciona/dp/B07KH8YWS5 // ---------------------------------------------------------------------------------------- #elif defined(SMARTLIFE_MINI_SMART_SOCKET) // Info #define MANUFACTURER "SMARTLIFE" #define DEVICE "MINI_SMART_SOCKET" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs //Red LED: 0 //Green LED: 4 //Blue LED: 2 // Light #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 #define LIGHT_CHANNELS 3 #define LIGHT_CH1_PIN 0 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 2 // BLUE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // ---------------------------------------------------------------------------------------- // Hama WiFi Steckdose (00176533) // https://at.hama.com/00176533/hama-wifi-steckdose-3500w-16a // ---------------------------------------------------------------------------------------- #elif defined(HAMA_WIFI_STECKDOSE_00176533) // Info #define MANUFACTURER "HAMA" #define DEVICE "WIFI_STECKDOSE_00176533" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 #define LED1_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // Oxaoxe NX-SP202 // Digoo NX-SP202 (not tested) // Digoo DG-SP202 (not tested) // https://github.com/xoseperez/espurna/issues/1502 // ----------------------------------------------------------------------------- #elif defined(DIGOO_NX_SP202) // Info #define MANUFACTURER "DIGOO" #define DEVICE "NX_SP202" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 #define BUTTON2_PIN 16 #define BUTTON2_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON2_RELAY 2 // Relays #define RELAY1_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_PIN 14 #define RELAY2_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 23296 #define HLW8012_VOLTAGE_RATIO 310085 #define HLW8012_POWER_RATIO 3368471 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // Foxel's LightFox dual // https://github.com/foxel/esp-dual-rf-switch // ----------------------------------------------------------------------------- #elif defined(FOXEL_LIGHTFOX_DUAL) // Info #define MANUFACTURER "FOXEL" #define DEVICE "LIGHTFOX_DUAL" #define SERIAL_BAUDRATE 19200 #define RELAY_PROVIDER RELAY_PROVIDER_DUAL #define DUMMY_RELAY_COUNT 2 #define DEBUG_SERIAL_SUPPORT 0 // Buttons #define BUTTON1_RELAY 1 #define BUTTON2_RELAY 2 #define BUTTON3_RELAY 2 #define BUTTON4_RELAY 1 #define BUTTON_EVENTS_SOURCE BUTTON_EVENTS_SOURCE_FOXEL_LIGHTFOX_DUAL // ----------------------------------------------------------------------------- // Teckin SP20 // ----------------------------------------------------------------------------- #elif defined(TECKIN_SP20) // Info #define MANUFACTURER "TECKIN" #define DEVICE "SP20" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 1 #define LED2_PIN 0 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_FINDME #define LED2_RELAY 0 // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // Charging Essentials / LITESUN LA-WF3 // ----------------------------------------------------------------------------- #elif defined(LITESUN_LA_WF3) // Info #define MANUFACTURER "LITESUN" #define DEVICE "LA_WF3" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 4 // 4 blue led #define LED1_MODE LED_MODE_WIFI #define LED1_PIN_INVERSE 1 #define LED2_PIN 5 // 5 red led #define LED2_MODE LED_MODE_RELAY #define LED2_PIN_INVERSE 1 // ----------------------------------------------------------------------------- // PSH // ----------------------------------------------------------------------------- #elif defined(PSH_WIFI_PLUG) // Info #define MANUFACTURER "PSH" #define DEVICE "WIFI_PLUG" // Relays #define RELAY1_PIN 2 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 #define LED1_PIN_INVERSE 0 #elif defined(PSH_RGBW_CONTROLLER) // Info #define MANUFACTURER "PSH" #define DEVICE "RGBW_CONTROLLER" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // LEDs #define LED1_PIN 13 #define LED1_PIN_INVERSE 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 5 // RED #define LIGHT_CH2_PIN 4 // GREEN #define LIGHT_CH3_PIN 12 // BLUE #define LIGHT_CH4_PIN 14 // WHITE1 #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 #elif defined(PSH_WIFI_SENSOR) // Info #define MANUFACTURER "PSH" #define DEVICE "WIFI_SENSOR" // DHT12 Sensor #define DHT_SUPPORT 1 #define DHT_PIN 14 #define DHT_TYPE DHT_CHIP_DHT12 // LDR Sensor #define LDR_SUPPORT 1 #define LDR_TYPE LDR_GL5528 #define LDR_ON_GROUND false #define LDR_RESISTOR 10000 #elif defined(JINVOO_VALVE_SM_AW713) // Reflashing from original Tuya firmware // to thirdparty firmware like espurna by: // https://github.com/ct-Open-Source/tuya-convert // Info #define MANUFACTURER "JINVOO" #define DEVICE "VALVE_SM_AW713" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LED #define LED1_PIN 5 // 5 red led #define LED1_PIN_INVERSE 0 #define LED1_RELAY 1 #define LED1_MODE LED_MODE_RELAY #define LED2_PIN 4 // 4 blue led #define LED2_PIN_INVERSE 0 #define LED2_RELAY 1 #define LED2_MODE LED_MODE_FINDME_WIFI #elif defined(TUYA_GENERIC_DIMMER) #define MANUFACTURER "TUYA" #define DEVICE "GENERIC_DIMMER" #define LIGHT_PROVIDER LIGHT_PROVIDER_TUYA #define LIGHT_CHANNELS 0 #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define DUMMY_RELAY_COUNT 0 // ----------------------------------------------------------------------------- // Etekcity ESW01-USA // https://www.amazon.com/Etekcity-Voltson-Outlet-Monitoring-Required/dp/B01M3MYIFS // ----------------------------------------------------------------------------- #elif defined(ETEKCITY_ESW01_USA) // Info #define MANUFACTURER "ETEKCITY" #define DEVICE "ESW01-USA" // Buttons #define BUTTON1_PIN 14 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 4 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs // Blue #define LED1_PIN 5 #define LED1_PIN_INVERSE 0 #define LED1_MODE LED_MODE_WIFI // Yellow #define LED2_PIN 16 #define LED2_PIN_INVERSE 0 #define LED2_MODE LED_MODE_FOLLOW #define LED2_RELAY 1 // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 15 #define HLW8012_CF1_PIN 12 #define HLW8012_CF_PIN 13 #define HLW8012_SEL_CURRENT HIGH // SEL pin to HIGH to measure current #define HLW8012_CURRENT_R 0.001 // Current resistor #define HLW8012_VOLTAGE_R_UP ( 4 * 470000 ) // Upstream voltage resistor #define HLW8012_VOLTAGE_R_DOWN ( 1000 ) // Downstream voltage resistor #define HLW8012_INTERRUPT_ON CHANGE // ----------------------------------------------------------------------------- // FS UAP1 // http://frank-schuetz.de/index.php/fhem/13-hoermann-torantrieb-mit-espeasy-in-fhem-einbinden #elif defined(FS_UAP1) // Info #define MANUFACTURER "FS" #define DEVICE "UAP1" // Inputs #define DIGITAL1_PIN 4 #define DIGITAL2_PIN 5 // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY3_PIN 14 #define RELAY4_PIN 15 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 2 #define LED1_PIN_INVERSE 0 // Disable UART noise #define DEBUG_SERIAL_SUPPORT 0 // ----------------------------------------------------------------------------- // TFLAG NX-SM100 & NX-SM200 // ----------------------------------------------------------------------------- #elif defined(TFLAG_NX_SMX00) // Info #define MANUFACTURER "TFLAG" #define DEVICE "NX_SMX00" // Buttons #define BUTTON1_PIN 13 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 12 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LEDs #define LED1_PIN 0 #define LED1_PIN_INVERSE 1 #define LED1_MODE LED_MODE_FOLLOW_INVERSE #define LED1_RELAY 1 #define LED2_PIN 15 #define LED2_PIN_INVERSE 1 #define LED2_MODE LED_MODE_WIFI // HJL01 / BL0937 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 16 #define HLW8012_CF1_PIN 14 #define HLW8012_CF_PIN 5 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 632 #define HLW8012_VOLTAGE_RATIO 313400 #define HLW8012_POWER_RATIO 3711185 #define HLW8012_INTERRUPT_ON FALLING // ----------------------------------------------------------------------------- // MUVIT_IO_MIOBULB001 // ----------------------------------------------------------------------------- #elif defined(MUVIT_IO_MIOBULB001) // Info #define MANUFACTURER "MUVIT_IO" #define DEVICE "MIOBULB001" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 14 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 13 // BLUE #define LIGHT_CH4_PIN 4 // WHITE #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // ----------------------------------------------------------------------------- // Hykker Power Plug (Smart Home Series) available in Jerónimo Martins Polska (Biedronka) // https://www.hykker.com/akcesoria/gniazdo-wi-fi-z-licznikiem-energii/ // Reflashing from original Tuya firmware // to thirdparty firmware like espurna by: // https://github.com/ct-Open-Source/tuya-convert // ----------------------------------------------------------------------------- #elif defined(HYKKER_SMART_HOME_POWER_PLUG) // Info #define MANUFACTURER "HYKKER" #define DEVICE "SMART_HOME_POWER_PLUG" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LED // Red #define LED1_PIN 13 #define LED1_MODE LED_MODE_WIFI #define LED1_PIN_INVERSE 1 // Blue connected to relay // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 282060 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING #define SENSOR_ENERGY_UNITS ENERGY_KWH #define SENSOR_POWER_UNITS POWER_WATTS // ----------------------------------------------------------------------------- // Kogan Smarter Home Plug with Energy Meter (Australia) // Product code: KASPEMHA // https://www.kogan.com/au/buy/kogan-smarterhome-smart-plug-energy-meter/ // Reflashing from original Tuya firmware // to thirdparty firmware like espurna by: // https://github.com/ct-Open-Source/tuya-convert // ----------------------------------------------------------------------------- #elif defined(KOGAN_SMARTER_HOME_PLUG_W_POW) // Info #define MANUFACTURER "KOGAN" #define DEVICE "SMARTER_HOME_PLUG_W_POW" // Buttons #define BUTTON1_PIN 0 #define BUTTON1_CONFIG BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH | BUTTON_SET_PULLUP #define BUTTON1_RELAY 1 // Relays #define RELAY1_PIN 14 #define RELAY1_TYPE RELAY_TYPE_NORMAL // LED // Red #define LED1_PIN 13 #define LED1_MODE LED_MODE_WIFI #define LED1_PIN_INVERSE 1 // Blue connected to relay // HLW8012 #ifndef HLW8012_SUPPORT #define HLW8012_SUPPORT 1 #endif #define HLW8012_SEL_PIN 12 #define HLW8012_CF1_PIN 5 #define HLW8012_CF_PIN 4 #define HLW8012_SEL_CURRENT LOW #define HLW8012_CURRENT_RATIO 25740 #define HLW8012_VOLTAGE_RATIO 282060 #define HLW8012_POWER_RATIO 3414290 #define HLW8012_INTERRUPT_ON FALLING #define SENSOR_ENERGY_UNITS ENERGY_KWH #define SENSOR_POWER_UNITS POWER_WATTS // ----------------------------------------------------------------------------- // LSC Smart LED Light Strip (Smart CXonnect Series) available ACTION (Germany) // https://www.action.com/de-de/p/lsc-smart-connect-intelligenter-multicolor-led-strip-/ // Reflashing from original Tuya firmware // to thirdparty firmware like espurna by: // https://github.com/ct-Open-Source/tuya-convert // ----------------------------------------------------------------------------- #elif defined(LSC_SMART_LED_LIGHT_STRIP) // Info #define MANUFACTURER "LSC" #define DEVICE "SMART_LED_LIGHT_STRIP" #define RELAY_PROVIDER RELAY_PROVIDER_LIGHT #define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER #define DUMMY_RELAY_COUNT 1 // Light RGBW #define LIGHT_CHANNELS 4 #define LIGHT_CH1_PIN 4 // RED #define LIGHT_CH2_PIN 12 // GREEN #define LIGHT_CH3_PIN 14 // BLUE #define LIGHT_CH4_PIN 13 // WHITE // #define LIGHT_CH5_PIN 5 // CW (not connected, but circuit supports it) #define LIGHT_CH1_INVERSE 0 #define LIGHT_CH2_INVERSE 0 #define LIGHT_CH3_INVERSE 0 #define LIGHT_CH4_INVERSE 0 // IR #define IR_SUPPORT 1 #define IR_RX_PIN 0 #define IR_BUTTON_SET 5 // ----------------------------------------------------------------------------- // eHomeDIY WT02 // https://github.com/eHomeDIY/WT02-hardware // ----------------------------------------------------------------------------- #elif defined(EHOMEDIY_WT02) // Info #define MANUFACTURER "EHOMEDIY" #define DEVICE "WT02" #define I2C_SDA_PIN 0 #define I2C_SCL_PIN 2 #define BMX280_SUPPORT 1 // #define SI7021_SUPPORT 1 // ----------------------------------------------------------------------------- // eHomeDIY WT03 // https://github.com/eHomeDIY/WT03-hardware // ----------------------------------------------------------------------------- #elif defined(EHOMEDIY_WT03) // Info #define MANUFACTURER "EHOMEDIY" #define DEVICE "WT03" #define I2C_SDA_PIN 2 #define I2C_SCL_PIN 0 #define BMX280_SUPPORT 1 // #define SI7021_SUPPORT 1 // ----------------------------------------------------------------------------- // Linksprite R4 // http://linksprite.com/wiki/index.php?title=LinkNode_R4:_Arduino-compatible_WiFi_relay_controller // ----------------------------------------------------------------------------- #elif defined(LINKSPRITE_LINKNODE_R4) // Info #define MANUFACTURER "LINKSPRITE" #define DEVICE "LINKNODE_R4" // Relays #define RELAY1_PIN 12 #define RELAY2_PIN 13 #define RELAY3_PIN 14 #define RELAY4_PIN 16 #define RELAY1_TYPE RELAY_TYPE_NORMAL #define RELAY2_TYPE RELAY_TYPE_NORMAL #define RELAY3_TYPE RELAY_TYPE_NORMAL #define RELAY4_TYPE RELAY_TYPE_NORMAL // ----------------------------------------------------------------------------- #else #error "UNSUPPORTED HARDWARE!!" #endif