// ----------------------------------------------------------------------------- // SENSORS // ----------------------------------------------------------------------------- #define SENSOR_DEBUG 0 // Debug sensors #define SENSOR_READ_INTERVAL 6000 // Read data from sensors every 6 seconds #define SENSOR_REPORT_EVERY 10 // Report every this many readings #define SENSOR_USE_INDEX 0 // Use the index in topic (i.e. temperature/0) // even if just one sensor (0 for backwards compatibility) #ifndef SENSOR_TEMPERATURE_UNITS #define SENSOR_TEMPERATURE_UNITS TMP_CELSIUS // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT) #endif #ifndef SENSOR_TEMPERATURE_CORRECTION #define SENSOR_TEMPERATURE_CORRECTION 0.0 // Offset correction #endif #ifndef TEMPERATURE_MIN_CHANGE #define TEMPERATURE_MIN_CHANGE 0.0 // Minimum temperature change to report #endif #ifndef HUMIDITY_MIN_CHANGE #define HUMIDITY_MIN_CHANGE 0 // Minimum humidity change to report #endif #define SENSOR_TEMPERATURE_DECIMALS 1 #define SENSOR_HUMIDITY_DECIMALS 0 #define SENSOR_PRESSURE_DECIMALS 2 #define SENSOR_ANALOG_DECIMALS 0 #define SENSOR_EVENTS_DECIMALS 0 #define SENSOR_CURRENT_DECIMALS 3 #define SENSOR_VOLTAGE_DECIMALS 0 #define SENSOR_POWER_DECIMALS 0 #define SENSOR_POWER_FACTOR_DECIMALS 0 #define SENSOR_ENERGY_DECIMALS 0 #define SENSOR_PM1dot0_DECIMALS 0 #define SENSOR_PM2dot5_DECIMALS 0 #define SENSOR_PM10_DECIMALS 0 #define SENSOR_CO2_DECIMALS 0 #define SENSOR_UNKNOWN_TOPIC "unknown" #define SENSOR_TEMPERATURE_TOPIC "temperature" #define SENSOR_HUMIDITY_TOPIC "humidity" #define SENSOR_PRESSURE_TOPIC "pressure" #define SENSOR_CURRENT_TOPIC "current" #define SENSOR_VOLTAGE_TOPIC "voltage" #define SENSOR_ACTIVE_POWER_TOPIC "power" #define SENSOR_APPARENT_POWER_TOPIC "apparent" #define SENSOR_REACTIVE_POWER_TOPIC "reactive" #define SENSOR_POWER_FACTOR_TOPIC "factor" #define SENSOR_ENERGY_TOPIC "energy" #define SENSOR_ENERGY_DELTA_TOPIC "energy_delta" #define SENSOR_PM1dot0_TOPIC "pm1dot0" #define SENSOR_PM2dot5_TOPIC "pm2dot5" #define SENSOR_PM10_TOPIC "pm10" #define SENSOR_ANALOG_TOPIC "analog" #define SENSOR_DIGITAL_TOPIC "digital" #define SENSOR_EVENTS_TOPIC "events" #define SENSOR_CO2_TOPIC "co2" #define HUMIDITY_NORMAL 0 #define HUMIDITY_COMFORTABLE 1 #define HUMIDITY_DRY 2 #define HUMIDITY_WET 3 //-------------------------------------------------------------------------------- // Analog sensor // Enable support by passing ANALOG_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef ANALOG_SUPPORT #define ANALOG_SUPPORT 0 #endif #ifndef ANALOG_PIN #define ANALOG_PIN 0 #endif #ifndef ANALOG_PIN_MODE #define ANALOG_PIN_MODE INPUT #endif #if ANALOG_SUPPORT #undef ADC_VCC_ENABLED #define ADC_VCC_ENABLED 0 #endif //-------------------------------------------------------------------------------- // BME280/BMP280 // Enable support by passing BMX280_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef BMX280_SUPPORT #define BMX280_SUPPORT 0 #endif #ifndef BMX280_ADDRESS #define BMX280_ADDRESS 0x00 // 0x00 means auto #endif #define BMX280_MODE 1 // 1 for forced mode, 3 for normal mode #define BMX280_TEMPERATURE 1 // Oversampling for temperature (set to 0 to disable magnitude) #define BMX280_HUMIDITY 1 // Oversampling for humidity (set to 0 to disable magnitude, only for BME280) #define BMX280_PRESSURE 1 // Oversampling for pressure (set to 0 to disable magnitude) #if BMX280_SUPPORT #undef I2C_SUPPORT #define I2C_SUPPORT 1 #endif //-------------------------------------------------------------------------------- // Dallas OneWire temperature sensors // Enable support by passing DALLAS_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef DALLAS_SUPPORT #define DALLAS_SUPPORT 0 #endif #ifndef DALLAS_PIN #define DALLAS_PIN 13 #endif #ifndef DALLAS_PULLUP #define DALLAS_PULLUP 1 #endif #define DALLAS_RESOLUTION 9 // Not used atm //-------------------------------------------------------------------------------- // DHTXX temperature/humidity sensor // Enable support by passing DHT_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef DHT_SUPPORT #define DHT_SUPPORT 0 #endif #ifndef DHT_PIN #define DHT_PIN 13 #endif #ifndef DHT_TYPE #define DHT_TYPE DHT22 #endif //-------------------------------------------------------------------------------- // Digital sensor // Enable support by passing DIGITAL_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef DIGITAL_SUPPORT #define DIGITAL_SUPPORT 0 #endif #ifndef DIGITAL_PIN #define DIGITAL_PIN 2 #endif #ifndef DIGITAL_PIN_MODE #define DIGITAL_PIN_MODE INPUT_PULLUP #endif #ifndef DIGITAL_DEFAULT_STATE #define DIGITAL_DEFAULT_STATE 1 #endif //-------------------------------------------------------------------------------- // Energy Monitor general settings //-------------------------------------------------------------------------------- #define EMON_MAX_SAMPLES 1000 // Max number of samples to get #define EMON_MAX_TIME 250 // Max time in ms to sample #define EMON_FILTER_SPEED 512 // Mobile average filter speed #define EMON_MAINS_VOLTAGE 230 // Mains voltage #define EMON_REFERENCE_VOLTAGE 3.3 // Reference voltage of the ADC #define EMON_CURRENT_RATIO 30 // Current ratio in the clamp (30V/1A) #define EMON_REPORT_CURRENT 0 // Report current #define EMON_REPORT_POWER 1 // Report power #define EMON_REPORT_ENERGY 1 // Report energy //-------------------------------------------------------------------------------- // Energy Monitor based on ADC121 // Enable support by passing EMON_ADC121_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef EMON_ADC121_SUPPORT #define EMON_ADC121_SUPPORT 0 // Do not build support by default #endif #define EMON_ADC121_I2C_ADDRESS 0x00 // 0x00 means auto #if EMON_ADC121_SUPPORT #undef I2C_SUPPORT #define I2C_SUPPORT 1 #endif //-------------------------------------------------------------------------------- // Energy Monitor based on ADS1X15 // Enable support by passing EMON_ADS1X15_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef EMON_ADS1X15_SUPPORT #define EMON_ADS1X15_SUPPORT 0 // Do not build support by default #endif #define EMON_ADS1X15_I2C_ADDRESS 0x00 // 0x00 means auto #define EMON_ADS1X15_TYPE ADS1X15_CHIP_ADS1115 #define EMON_ADS1X15_GAIN ADS1X15_REG_CONFIG_PGA_4_096V #define EMON_ADS1X15_MASK 0x0F // A0=1 A1=2 A2=4 A4=8 #if EMON_ADS1X15_SUPPORT #undef I2C_SUPPORT #define I2C_SUPPORT 1 #endif //-------------------------------------------------------------------------------- // Energy Monitor based on interval analog GPIO // Enable support by passing EMON_ANALOG_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef EMON_ANALOG_SUPPORT #define EMON_ANALOG_SUPPORT 0 // Do not build support by default #endif #if EMON_ANALOG_SUPPORT #undef ADC_VCC_ENABLED #define ADC_VCC_ENABLED 0 #endif //-------------------------------------------------------------------------------- // Counter sensor // Enable support by passing EVENTS_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef EVENTS_SUPPORT #define EVENTS_SUPPORT 0 // Do not build with counter support by default #endif #ifndef EVENTS_PIN #define EVENTS_PIN 2 // GPIO to monitor #endif #ifndef EVENTS_PIN_MODE #define EVENTS_PIN_MODE INPUT // INPUT, INPUT_PULLUP #endif #ifndef EVENTS_INTERRUPT_MODE #define EVENTS_INTERRUPT_MODE RISING // RISING, FALLING, BOTH #endif #define EVENTS_DEBOUNCE 50 // Do not register events within less than 10 millis //-------------------------------------------------------------------------------- // MHZ19 CO2 sensor // Enable support by passing MHZ19_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef MHZ19_SUPPORT #define MHZ19_SUPPORT 0 #endif #define MHZ19_RX_PIN 13 #define MHZ19_TX_PIN 15 //-------------------------------------------------------------------------------- // Particle Monitor based on Plantower PMSX003 // Enable support by passing PMSX003_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef PMSX003_SUPPORT #define PMSX003_SUPPORT 0 #endif #define PMS_RX_PIN 13 #define PMS_TX_PIN 15 //-------------------------------------------------------------------------------- // SI7021 temperature & humidity sensor // Enable support by passing SI7021_SUPPORT=1 build flag //-------------------------------------------------------------------------------- #ifndef SI7021_SUPPORT #define SI7021_SUPPORT 0 #endif #ifndef SI7021_ADDRESS #define SI7021_ADDRESS 0x00 // 0x00 means auto #endif #if SI7021_SUPPORT #undef I2C_SUPPORT #define I2C_SUPPORT 1 #endif // ----------------------------------------------------------------------------- // I2C // ----------------------------------------------------------------------------- #ifndef I2C_SUPPORT #define I2C_SUPPORT 0 // I2C enabled (1.98Kb) #endif #define I2C_USE_BRZO 0 // Use brzo_i2c library or standard Wire #ifndef I2C_SDA_PIN #define I2C_SDA_PIN SDA // SDA GPIO (Sonoff => 4) #endif #ifndef I2C_SCL_PIN #define I2C_SCL_PIN SCL // SCL GPIO (Sonoff => 14) #endif #define I2C_CLOCK_STRETCH_TIME 200 // BRZO clock stretch time #define I2C_SCL_FREQUENCY 1000 // BRZO SCL frequency #define I2C_CLEAR_BUS 0 // Clear I2C bus at boot //-------------------------------------------------------------------------------- // Internal power monitor // Enable support by passing ADC_VCC_ENABLED=1 build flag // Do not enable this if using the analog GPIO for any other thing //-------------------------------------------------------------------------------- #ifndef ADC_VCC_ENABLED #define ADC_VCC_ENABLED 1 #endif #if ADC_VCC_ENABLED ADC_MODE(ADC_VCC); #endif //-------------------------------------------------------------------------------- // Class loading //-------------------------------------------------------------------------------- #include "sensors/BaseSensor.h" #if ANALOG_SUPPORT #include "sensors/AnalogSensor.h" #endif #if BMX280_SUPPORT #include #include "sensors/BMX280Sensor.h" #endif #if DALLAS_SUPPORT #include #include "sensors/DallasSensor.h" #endif #if DHT_SUPPORT #include "sensors/DHTSensor.h" #endif #if DIGITAL_SUPPORT #include "sensors/DigitalSensor.h" #endif #if EMON_ADC121_SUPPORT #include "sensors/EmonADC121Sensor.h" #endif #if EMON_ADS1X15_SUPPORT #include "sensors/EmonADS1X15Sensor.h" #endif #if EMON_ANALOG_SUPPORT #include "sensors/EmonAnalogSensor.h" #endif #if EVENTS_SUPPORT #include "sensors/EventSensor.h" #endif #if MHZ19_SUPPORT #include #include "sensors/MHZ19Sensor.h" #endif #if PMSX003_SUPPORT #include #include #include "sensors/PMSX003Sensor.h" #endif #if SI7021_SUPPORT #include "sensors/SI7021Sensor.h" #endif