4.3 KiB
ESPurna
ESPurna ("spark" in Catalan) is a custom C firmware for ITead Sonoff Smart WiFi Switch. This device has an ESP8266 on board with a 8Mbit flash memory chip, a mains to 3V3 transformer and a relay (GPIO12). It also features a button (GPIO0), an LED (GPIO13) and an unpopulated header you can use to reprogram it. You can read about this board and firmware in my blog.
Features
- WebServer for configuration and simple relay toggle
- Flashing firmware Over-The-Air (OTA)
- Up to 3 configurable WIFI networks
- MQTT support with configurable host and topic
- Manual switch ON/OFF with button (single click the button)
- AP mode backup (double click the button)
- Support for custom RF module (check blog post)
- Visual status of the connection via the LED
Flashing
The unpopulated header has all the required pins. My board has a 5 pins header in-line with the button. They are (from the button outwards):
- 3V3
- RX
- TX
- GND
- GPIO14
Last one is not necessary. Mind it's a 3V3 device, if connected to 5V you will probably fry it. Button is connected to GPIO0 on the ESP8266 chip, so to enter flash mode you have to hold the button pressed while powering on the board, then you can realease it again.
The project is ready to be build using PlatformIO. Please refer to their web page for instructions on how to install the builder. Once installed:
> platformio run --target upload -e wire
> platformio run --target uploadfs -e wire
Once you have flashed it you can flash it again over-the-air using the ota environment:
> platformio run --target upload -e ota
> platformio run --target uploadfs -e ota
When using OTA environment it defaults to the IP address of the device in SoftAP mode. If you want to flash it when connected to your home network best way is to supply the IP of the device:
> platformio run --target upload -e ota --upload-port 192.168.1.151
> platformio run --target uploadfs -e ota --upload-port 192.168.1.151
Library dependencies are automatically managed via PlatformIO Library Manager.
Usage
On normal boot (i.e. button not pressed) it will execute the firmware. It configures the hardware (button, LED, relay), the SPIFFS memory access, the WIFI, the WebServer and MQTT connection.
Obviously the default values for WIFI network and MQTT will probably not match your requirements. The device will start in Soft AP creating a WIFI SSID named "SONOFF_XXXXXX", where XXXXXX are the last 3 bytes of the radio MAC. Connect with phone, PC, laptop, whatever to that network, password is "fibonacci". Once connected browse to 192.168.4.1 and you will be presented a configuration page where you will be able to define up to 3 possible WIFI networks and the MQTT configuration parameters.
It will then try to connect to the first WIFI network. If fail it will try the second in 30 seconds, and so on. Once connected it will try to connect the MQTT server. If there are no configured networks or none of the configured ones is reachable it defaults to SoftAP mode. You can also switch to SoftAP mode by double clicking the on board button.
The device will publish the relay state to the given topic and it will subscribe to the same topic plus "/set" for remote switching. So if your topic is "/home/living/switch" you will be able to switch it on/off sending "1"/"0" to "/home/living/switch/set".
You can also use "{identifier}" as place holder in the topic. It will be translated to your device ID (same as the soft AP network it creates).
Troubleshooting
After flashing the firmware via serial do a hard reset of the device (unplug & plug). There is an issue with the ESP.reset() method. Check https://github.com/esp8266/Arduino/issues/1017 for more info.
Current version of ESP8266httpUpdate restarts the modules after SPIFFS update, thus preventing the firmware to be updated too. There is a recent commit fixing that which is not yet pushed to PLatformIO. Check Fix example for ESP8266httpUpdate for more info.