Fork of the espurna firmware for `mhsw` switches
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

13 KiB

ESPurna change log

The format is based on Keep a Changelog and this project adheres to Semantic Versioning.

[1.8.1] 2017-05-22

Fix

  • Issue #140. Fix no relay control bug in Sonoff Dual

[1.8.0] 2017-05-21

Added

  • Added gamma correction to RGB strips. Thanks to Chris Ward.
  • Added support for Huacanxing H801 WiFi LED Controller. Thanks to Minh Phuong Ly.
  • Issue #138. Added NTP configuration from web interface
  • Issue #128. Report color when booting and in heartbeat stream.
  • Issue #126. Show NTP status in web interface.
  • Added filter limits on POW readings.
  • Added color temperature to RGB calculation. Thanks to Sacha Telgenhof.
  • Issue #120. Added relay flood protection. Thanks to Izik Dubnov.
  • Support for "#RRGGBB", "RRR,GGG,BBB" and "WWW" color formats.
  • Issue #117. Added build date & time to web interface.

Fix

  • Fix MQTT_RELAY board conifugration. Thanks to Denis French.
  • Issue #125. Fix bug in relay status reading from EEPROM
  • Issue #127. Fix button action in DUAL.
  • Fix bug in Sonoff POW current reading. Thanks to Emmanuel Tatto.
  • Minimizing my9291 flickering when booting.
  • Fix conditional flags in hardware.ino to support Arduino IDE.

[1.7.1] 2017-03-28

Fix

  • Issue #113. Fix restoring color from EEPROM upon reboot
  • Issue #113. Fix bug in API handlers

[1.7.0] 2017-03-27

Added

  • Web interface embedded in firmware image by default
  • Upload firmware image from web interface
  • Added API entry point to change light color
  • Added generic analog sensor. Thanks to Francesco Boscarino
  • Report RSSI value in debug console and MQTT status messages
  • Added support for Magic Home LED Controller
  • Added support for ESPurna-H Board (based on HLW8012)
  • Added forward compatible code for v2.0

Changed

  • Added ellipsis (...) in debug messages longer than 80 characters
  • Changed topic constants in code
  • Prevent the SDK from saving WiFi configuration to flash

Fix

  • Issue #113. Fix light bulb state to OFF in library prevented the bulb from turning on
  • Issue #58. Added code to handle spurious readings
  • Fix bug in HLW8012 calibration current parameter casting to int instead of float
  • Issue #115. Removed local declaration of _mqttForward variable. Thanks to Paweł Fiedor
  • Fix MQTT will topic. Thanks to Asbjorn Tronhus

[1.6.9] 2017-03-12

Added

  • Two stage read for DS18B20 devices. Thanks to Izik Dubnov.
  • Option to report the relay status via MQTT periodically
  • Terminal commands to change relay status an light color
  • Added debug via UDP (disabled by default)
  • Moved debug strings to PROGMEM. ~1.5KByes memory freed
  • Avoid broadcasting websocket messages if no clients connected

Fix

  • Fixing use after free bug that leads to corrupted auth credentials. Thanks to David Guillen

[1.6.8] 2017-03-01

Added

  • Issue #85. Heartbeat reports now free heap, uptime and VCC every 5 minutes

Changed

  • Wait two minutes instead of one in AP mode before trying to reconnect to the router
  • Issue #92. Debug log enabled by default in Arduino IDE
  • Issue #91. Using AsyncMqttClient as default MQTT client again

Fix

  • Report data from all sensors via websocket even if no MQTT connection
  • Issue #92. Fix unknown reference in Arduino IDE
  • Split data.h contents into 1k lines, otherwise Arduino IDE chokes on them
  • Discard empty MQTT topic while subscribing

[1.6.7] 2017-02-25

Added

  • Support for OpenLight / AI-Light by AI-Thinker based on MY9291 LED driver
  • Issue #87. Factory reset when physical button pressed for >10 seconds

[1.6.6] 2017-02-23

Fix

  • Issue #82. Fix critical bug on Sonoff Dual

[1.6.5] 2017-02-22

Added

  • Option to backup and restore settings from the web interface
  • Footer in the web interface

Changed

  • Using PubSubClient as MQTT client by default (please read the documentation)
  • Double & long clicks do nothing except for the first defined button

Fix

  • Issue #79. Fix bug in WiFi led notification & MQTT connectivity (using PubSubClient)
  • Issue #73. Fix bug when building without Domoticz support
  • Fix Gulp tasks dependencies

[1.6.4] 2017-02-20

Added

  • Option to embed the web interface in the firmware, disabled by default
  • Change relay status with a GET request (browser friendly)
  • Support for PROGMEM debug messages (only wifi module has been changed)
  • Option to disable mDNS, enabled by default
  • Show current web server port in debug log
  • Issue #75. Link relays to LEDs
  • Issue #76. Using http://espurna.local when in AP mode

Changed

  • Images and favicon is now embedded in the HTML
  • Authentication challenge only in /auth request. All static contents are un-authenticated
  • HTTP response code when out of websocket slots changed from 423 to 429

Fix

  • Memory leak in MQTT connection method
  • Wait 60 seconds before retrying to connect when in AP mode
  • Issue #24 & #74. Update ESPAsyncTCP and ESPAsyncWebServer to latest GIT version that supports MSS defragmenting
  • Issue #73. Fixes for windows machines

Removed

  • Captive portal removed, mDNS resolution for AP mode too

[1.6.3] 2017-02-15

Added

  • Issue #69. Temperature unit configuration from the web interface
  • Issue #55. WebServer port configurable from the web interface, defaults to 80
  • Expand network configuration when adding a new network

Changed

  • Merged web contents except images in a single compressed file for reliability
  • Update support for Itead Motor Clockwise/Anticlockwise board
  • Scan for strongest network only if more than 1 network configured

Fix

  • Issue #71. Added default values for netmask and DNS in web configuration
  • Fixed Itead 1CH self-locking/inching board definition
  • Fixed PlatformIO environments for ESP8285 boards (4CH and Touch)

[1.6.2] 2017-02-10

Fix

  • Check if there is an MQTT broker defined before the MQTT_MAX_TRIES check

[1.6.1] 2017-02-10

Added

  • Added support for Jorge Garcia's Wifi+Relay Board Kit
  • Reporting current and energy incrementals to a separate counters in Domoticz (thanks to Toni Arte)
  • Force WiFi reconnect after MQTT_MAX_TRIES fails trying to connect to MQTT broker

[1.6.0] 2017-02-05

Added

  • Added support for toggle switches
  • Allow reset the board via an MQTT message
  • Allow reset the board via an RPC (HTTP) message
  • Added support for ADC121 I2C for current monitoring (Check http://tinkerman.cat/power-monitoring-sonoff-th-adc121/)
  • Reporting voltage to Domoticz (only HLW8012)
  • Map button events to actions (toggle relay, AP mode, reset, pulse mode)

Changed

  • Reporting energy incrementals (Domoticz, MQTT)

Removed

  • Removed current monitor bypass when relay is OFF
  • Removed energy API entry point

[1.5.4] 2017-02-03

Fixed

  • Issue #50. Fix type bug in window variable when calculating energy for HLW8012 devices (Sonoff POW)

[1.5.3] 2017-02-02

Fixed

  • Issue #50 and #54. Fixed domoticz MQTT message format

Added

  • Energy calculation and aggregation. API entry points and MQTT messages.

[1.5.2] 2017-01-29

Fixed

  • Fix bug in emon topic payload

[1.5.1] 2017-01-28

Added

  • OpenEnergyMonitor WiFi MQTT Relay / Thermostat support (thanks to Denis French)

Fixed

  • NTP connection refresh upon wifi connection
  • Filesystem image build using local gulp installation

[1.5.0] 2017-01-21

Added

  • Pulse mode. Allows to define a pulse time after which the relay will switch back
  • API entry points for sensor data (power, current, voltage, temperature and humidity)
  • Export sensor data to Domoticz (power, current, voltage, temperature and humidity)
  • Configurable (in code) mapping between buttons and relays
  • MQTT messages for button events
  • Added support for Itead Studio 1CH inching/self locking smart switch board
  • Added support for Jan Goedeke Wifi Relay boards (both NC and NO versions)
  • Notify OTA updates to websocket clients, automatically reload page
  • Support for pulse mode notification LED and button
  • Revert relay state mode on boot (thanks to Minh Phuong Ly)

Fixed

  • MQTT will topic
  • Crash with HLW812 interrupts while trying to create a WIFI connection
  • Issue #20 Better inline documentation for Alexa and Domoticz default settings
  • Issue #39 Fixed autoconnect issue with static IP (fixed in JustWifi library)
  • Issue #41 Added password requirements to initial password change page

Changed

  • Changed LED pattern for WIFI notifications (shorter pulses)

[1.4.4] 2017-01-13

Added

  • Adding current, voltage, apparent and reactive power reports to Sonoff POW (Web & MQTT)

Fixed

  • Issue #35 Fixed frequent MQTT connection drops after WIFI reconnect
  • Defer wifi disconnection from web interface to allow request to return

Changed

  • Move all Arduino IDE configuration values to their own file
  • Using latest HLW8012 library in interrupt mode

[1.4.3] 2017-01-11

Fixed

  • Issue #6 Using forked Time library to prevent conflict with Arduino Core for ESP8266 time.h file in windows machines

[1.4.2] 2017-01-09

Added

  • Support for inverse logic relays

Fixed

  • Issue #31. Fixed error in relay identification from MQTT messages

[1.4.1] 2017-01-05

Added

  • Alexa support by default on all devices
  • Added support for Wemos D1 Mini board with official Relay Shield

Fixed

  • Multi-packet websocket frames

[1.4.0] 2016-12-31

Added

Fixed

  • Issue #16. Enforce minimum password strength in web interface

Changed

  • Using default client_id provided by AsyncMqttClient
  • Allow up to 5 different WIFI networks

Removed

  • File system version file

[1.3.1] 2016-12-31

Fixed

  • data_dir fix for PlatformIO

[1.3.0] 2016-12-30

Changed

  • Arduino IDE support (changes in the folder structure and documentation)

[1.2.0] 2016-12-27

Added

  • Force password changing if it's the default one
  • Added Last-Modified header to static contents
  • Added DNS captive portal for AP mode
  • Added support for Sonoff 4CH
  • Added support for WorkChoice ecoPlug (ECOPLUG). Thanks to David Myers
  • Added support for Sonoff SV
  • Added support for Sonoff Touch
  • Comment out hardware selection in hardware.h if using Arduino IDE
  • Added support for MQTT get/set suffixes (/status, /set, ...)
  • Added support for LED notifications via MQTT
  • Added EEPROM check commands to terminal interface

Changed

  • Using unreleased AsyncMqttClient with stability improvements
  • Better decoupling between MQTT and relays/websockets
  • Skipping retained MQTT messages (configurable)

Fixed

  • Issue #11 Compile error when building sonoff-dual-debug
  • Issue #14 MQTT Connection with Username an Password not working
  • Issue #17 Moved static variable 'pending' to class variable

[1.1.0] 2016-12-06

Added

  • Added support for DS18B20 temperature sensor. Thanks to Francesco Boscarino
  • Added reset command from console
  • Added support for multirelay boards like Sonoff DUAL or Electrodragon ESP Relay Board

Changed

  • Not using espressif8266_stage in default environment
  • Relay MQTT topics
  • API entry points

Removed

  • Old non protected API

[1.0.3] 2016-11-29

Added

  • WeMo emulation through the fauxmoESP library (control your switch from Alexa!)
  • REST API for relay management
  • Better dependency definitions in platformio.ini
  • Option to define inverse logic to on-board LED
  • Built data folder included in repo

Changed

  • Using non-interrupt driven mode for HLW8012
  • Better documentation
  • Small changes to web interface
  • Same admin password for web, OTA and WIFI AP mode

Fixed

  • Prevent fauxmoESP to be compiled by default

Removed

  • Removed ESPurna board to its own repo

[1.0.1] 2016-11-13

Added

  • Basic authentication and CSRF to websocket requests

[1.0.0] 2016-11-13

Added

  • Using ESPAsyncWebServer (for web & websockets) and AsyncMqttClient

[0.9.9] 2016-11-12

Added

  • Preliminary support for Sonoff POW
  • Replace AJAX requests with websockets
  • Using sprites for images
  • Hostname can be changed
  • Added initial relay state mode
  • Reconnect and reset buttons on web interface

Changed

  • Changed long click to reset and double click to AP mode
  • Using officially supported platformio.ini file by default

Fixed

[0.9.8] 2016-10-06

Added

  • Using PureCMS for the web interface
  • Using gulp to build the filesystem files
  • Using Embedis for configuration

Changed

  • Updated JustWifi library
  • Web interface changes
  • Using custom platformio.ini file
  • Loads of changes in modules
  • Added DEBUG_MSG

Fixed

  • Clean gulp builder script

[0.9.7] 2016-08-28

Changed

  • Moving wifi management to library (JustWifi)
  • Split code into modules

[0.9.6] 2016-08-12

Added

  • Added heartbeat, version and fsversion MQTT messages

Changed

  • GZip 3rd party contents

[0.9.5] 2016-07-31

  • Initial stable version