Fork of the espurna firmware for `mhsw` switches
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

146 lines
5.1 KiB

//------------------------------------------------------------------------------
// GENERAL
//------------------------------------------------------------------------------
#define SERIAL_BAUDRATE 115200
#define HOSTNAME DEVICE
#define BUFFER_SIZE 1024
#define HEARTBEAT_INTERVAL 300000
//--------------------------------------------------------------------------------
// EEPROM
//--------------------------------------------------------------------------------
#define EEPROM_RELAY_STATUS 0
#define EEPROM_POWER_COUNT 1
//--------------------------------------------------------------------------------
// RELAY
//--------------------------------------------------------------------------------
#define RELAY_MODE_OFF 0
#define RELAY_MODE_ON 1
#define RELAY_MODE_SAME 2
#define RELAY_MODE_TOOGLE 3
#define RELAY_SYNC_ANY 0
#define RELAY_SYNC_NONE_OR_ONE 1
#define RELAY_SYNC_ONE 2
#define RELAY_SYNC_SAME 3
#define RELAY_PULSE_NONE 0
#define RELAY_PULSE_OFF 1
#define RELAY_PULSE_ON 2
// Pulse time in seconds
#define RELAY_PULSE_TIME 1
// 0 means OFF, 1 ON and 2 whatever was before
#define RELAY_MODE RELAY_MODE_OFF
// 0 means ANY, 1 zero or one and 2 one and only one
#define RELAY_SYNC RELAY_SYNC_ANY
// 0 means no pulses, 1 means normally off, 2 normally on
#define RELAY_PULSE_MODE RELAY_PULSE_NONE
//--------------------------------------------------------------------------------
// LED
//--------------------------------------------------------------------------------
// All defined LEDs in the board can be managed through MQTT
// except the first one when LED_AUTO is set to 1.
// If LED_AUTO is set to 1 the board will use first defined LED to show wifi status.
#define LED_AUTO 1
// -----------------------------------------------------------------------------
// WIFI & WEB
// -----------------------------------------------------------------------------
#define WIFI_RECONNECT_INTERVAL 300000
#define WIFI_MAX_NETWORKS 5
#define ADMIN_PASS "fibonacci"
#define HTTP_USERNAME "admin"
#define WS_BUFFER_SIZE 5
#define WS_TIMEOUT 1800000
#define DNS_PORT 53
// -----------------------------------------------------------------------------
// OTA & NOFUSS
// -----------------------------------------------------------------------------
#define OTA_PORT 8266
#define NOFUSS_SERVER "http://192.168.1.100"
#define NOFUSS_INTERVAL 3600000
// -----------------------------------------------------------------------------
// MQTT
// -----------------------------------------------------------------------------
#define MQTT_SERVER "192.168.1.100"
#define MQTT_PORT 1883
#define MQTT_TOPIC "/test/switch/{identifier}"
#define MQTT_RETAIN true
#define MQTT_QOS 0
#define MQTT_KEEPALIVE 30
#define MQTT_RECONNECT_DELAY 10000
#define MQTT_SKIP_RETAINED 1
#define MQTT_SKIP_TIME 1000
#define MQTT_RELAY_TOPIC "/relay"
#define MQTT_LED_TOPIC "/led"
#define MQTT_BUTTON_TOPIC "/button"
#define MQTT_IP_TOPIC "/ip"
#define MQTT_VERSION_TOPIC "/version"
#define MQTT_HEARTBEAT_TOPIC "/status"
#define MQTT_CONNECT_EVENT 0
#define MQTT_DISCONNECT_EVENT 1
#define MQTT_MESSAGE_EVENT 2
// Custom get and set postfixes
// Use something like "/status" or "/set", with leading slash
#define MQTT_USE_GETTER ""
#define MQTT_USE_SETTER ""
// -----------------------------------------------------------------------------
// I2C
// -----------------------------------------------------------------------------
#define ENABLE_I2C 1
#define I2C_SDA_PIN 4
#define I2C_SCL_PIN 14
#define I2C_CLOCK_STRETCH_TIME 200
#define I2C_SCL_FREQUENCY 1000
// -----------------------------------------------------------------------------
// DOMOTICZ
// -----------------------------------------------------------------------------
#ifndef ENABLE_DOMOTICZ
#define ENABLE_DOMOTICZ 1
#endif
#define DOMOTICZ_IN_TOPIC "domoticz/in"
#define DOMOTICZ_OUT_TOPIC "domoticz/out"
// -----------------------------------------------------------------------------
// NTP
// -----------------------------------------------------------------------------
#define NTP_SERVER "pool.ntp.org"
#define NTP_TIME_OFFSET 1
#define NTP_DAY_LIGHT true
#define NTP_UPDATE_INTERVAL 1800
// -----------------------------------------------------------------------------
// FAUXMO
// -----------------------------------------------------------------------------
// This setting defines whether Alexa support should be built into the firmware
#ifndef ENABLE_FAUXMO
#define ENABLE_FAUXMO 1
#endif
// This is default value for the fauxmoEnabled setting that defines whether
// this device should be discoberable and respond to Alexa commands.
// Both ENABLE_FAUXMO and fauxmoEnabled should be 1 for Alexa support to work.
#define FAUXMO_ENABLED 1