mh
/
mhsw-espurna


								//--------------------------------------------------------------------------------

								// Custom RF module

								// Check http://tinkerman.cat/adding-rf-to-a-non-rf-itead-sonoff/

								// Enable support by passing RF_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef RF_SUPPORT

								#define RF_SUPPORT                  0

								#endif


								#define RF_PIN                      14

								#define RF_CHANNEL                  31

								#define RF_DEVICE                   1


								//--------------------------------------------------------------------------------

								// DHTXX temperature/humidity sensor

								// Enable support by passing DHT_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef DHT_SUPPORT

								#define DHT_SUPPORT                 0

								#endif


								#define DHT_PIN                     14

								#define DHT_UPDATE_INTERVAL         60000

								#define DHT_TYPE                    DHT22

								#define DHT_TIMING                  11

								#define DHT_TEMPERATURE_TOPIC       "temperature"

								#define DHT_HUMIDITY_TOPIC          "humidity"


								#define HUMIDITY_NORMAL             0

								#define HUMIDITY_COMFORTABLE        1

								#define HUMIDITY_DRY                2

								#define HUMIDITY_WET                3


								//--------------------------------------------------------------------------------

								// Analog sensor

								// Enable support by passing ANALOG_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef ANALOG_SUPPORT

								#define ANALOG_SUPPORT              0

								#endif


								#define ANALOG_PIN                  0

								#define ANALOG_UPDATE_INTERVAL      60000

								#define ANALOG_TOPIC                "analog"


								#if ANALOG_SUPPORT

								    #undef ADC_VCC_ENABLED

								    #define ADC_VCC_ENABLED         0

								#endif


								//--------------------------------------------------------------------------------

								// Counter sensor

								// Enable support by passing COUNTER_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef COUNTER_SUPPORT

								#define COUNTER_SUPPORT             0           // Do not build with counter support by default

								#endif


								#define COUNTER_PIN                 2           // GPIO to monitor

								#define COUNTER_PIN_MODE            INPUT       // INPUT, INPUT_PULLUP

								#define COUNTER_INTERRUPT_MODE      RISING      // RISING, FALLING, BOTH

								#define COUNTER_UPDATE_INTERVAL     5000        // Update counter every this millis

								#define COUNTER_REPORT_EVERY        12          // Report counter every this updates (1 minute)

								#define COUNTER_DEBOUNCE            10          // Do not register events within less than 10 millis

								#define COUNTER_TOPIC               "counter"   // Default topic for MQTT, API and InfluxDB


								//--------------------------------------------------------------------------------

								// DS18B20 temperature sensor

								// Enable support by passing DS18B20_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef DS18B20_SUPPORT

								#define DS18B20_SUPPORT             0

								#endif


								#define DS18B20_PIN                 14

								#define DS18B20_UPDATE_INTERVAL     60000

								#define DS18B20_TEMPERATURE_TOPIC   "temperature"


								//--------------------------------------------------------------------------------

								// Custom current sensor

								// Check http://tinkerman.cat/your-laundry-is-done/

								// Check http://tinkerman.cat/power-monitoring-sonoff-th-adc121/

								// Enable support by passing EMON_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef EMON_SUPPORT

								#define EMON_SUPPORT                0

								#endif


								#define EMON_ANALOG_PROVIDER        0

								#define EMON_ADC121_PROVIDER        1


								// If you select EMON_ADC121_PROVIDER you need to enable and configure I2C in general.h

								#define EMON_PROVIDER               EMON_ANALOG_PROVIDER


								#if EMON_PROVIDER == EMON_ANALOG_PROVIDER

								    #define EMON_CURRENT_PIN        0

									#define EMON_ADC_BITS           10

									#define EMON_REFERENCE_VOLTAGE  1.0

								    #define EMON_CURRENT_OFFSET     0.25

								    #if EMON_SUPPORT

								        #undef ADC_VCC_ENABLED

										#define ADC_VCC_ENABLED     0

								    #endif

								#endif


								#if EMON_PROVIDER == EMON_ADC121_PROVIDER

								    #define EMON_ADC121_ADDRESS     0x50

									#define EMON_ADC_BITS           12

									#define EMON_REFERENCE_VOLTAGE  3.3

								    #define EMON_CURRENT_OFFSET     0.10

								#endif


								#define EMON_CURRENT_RATIO          30

								#define EMON_SAMPLES                1000

								#define EMON_INTERVAL               10000

								#define EMON_MEASUREMENTS           6

								#define EMON_MAINS_VOLTAGE          230

								#define EMON_APOWER_TOPIC           "apower"

								#define EMON_ENERGY_TOPIC           "energy"

								#define EMON_CURRENT_TOPIC          "current"


								//--------------------------------------------------------------------------------

								// HLW8012 power sensor (Sonoff POW, Espurna H)

								// Enable support by passing HLW8012_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef HLW8012_SUPPORT

								#define HLW8012_SUPPORT             0

								#endif


								// GPIOs defined in the hardware.h file


								#define HLW8012_USE_INTERRUPTS      1

								#define HLW8012_SEL_CURRENT         HIGH

								#define HLW8012_CURRENT_R           0.001

								#define HLW8012_VOLTAGE_R_UP        ( 5 * 470000 ) // Real: 2280k

								#define HLW8012_VOLTAGE_R_DOWN      ( 1000 ) // Real 1.009k

								#define HLW8012_POWER_TOPIC         "power"

								#define HLW8012_CURRENT_TOPIC       "current"

								#define HLW8012_VOLTAGE_TOPIC       "voltage"

								#define HLW8012_APOWER_TOPIC        "apower"

								#define HLW8012_RPOWER_TOPIC        "rpower"

								#define HLW8012_PFACTOR_TOPIC       "pfactor"

								#define HLW8012_ENERGY_TOPIC        "energy"

								#define HLW8012_UPDATE_INTERVAL     5000

								#define HLW8012_REPORT_EVERY        12

								#define HLW8012_MIN_POWER           5

								#define HLW8012_MAX_POWER           2500

								#define HLW8012_MIN_CURRENT         0.05

								#define HLW8012_MAX_CURRENT         10


								//--------------------------------------------------------------------------------

								// V9261F power sensor (Intertek)

								// Enable support by passing V9261F_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef V9261F_SUPPORT

								#define V9261F_SUPPORT              0

								#endif


								#define V9261F_SYNC_INTERVAL        600

								#define V9261F_REPORT_INTERVAL      60000


								#define V9261F_BAUDRATE             4800


								#define V9261F_CURRENT_FACTOR       81156358

								#define V9261F_VOLTAGE_FACTOR       4178508

								#define V9261F_POWER_FACTOR         157859

								#define V9261F_RPOWER_FACTOR        V9261F_CURRENT_FACTOR


								//--------------------------------------------------------------------------------

								// Internal power montior

								// Enable support by passing ADC_VCC_ENABLED=1 build flag

								// Do not enable this if using the analog GPIO for any other thing

								//--------------------------------------------------------------------------------


								#ifndef ADC_VCC_ENABLED

								#define ADC_VCC_ENABLED             1

								#endif


								#if ADC_VCC_ENABLED

								    ADC_MODE(ADC_VCC);

								#endif