mh
/
mhsw-espurna


								//------------------------------------------------------------------------------

								// Do not change this file unless you know what you are doing

								// Configuration settings are in the settings.h file

								//------------------------------------------------------------------------------


								//------------------------------------------------------------------------------

								// GENERAL

								//------------------------------------------------------------------------------


								#define SERIAL_BAUDRATE         115200          // Debugging console boud rate

								#define HOSTNAME                DEVICE          // Hostname

								#define UPTIME_OVERFLOW         4294967295      // Uptime overflow value


								//--------------------------------------------------------------------------------

								// DEBUG

								//--------------------------------------------------------------------------------


								#ifndef DEBUG_PORT

								#define DEBUG_PORT              Serial          // Default debugging port

								#endif


								// Uncomment and configure these lines to enable remote debug via udpDebug

								// To receive the message son the destination computer use nc:

								// nc -ul 8111


								#define DEBUG_UDP_IP            IPAddress(192, 168, 1, 100)

								#define DEBUG_UDP_PORT          8113


								//--------------------------------------------------------------------------------

								// EEPROM

								//--------------------------------------------------------------------------------


								#define EEPROM_RELAY_STATUS     0               // Address for the relay status (1 byte)

								#define EEPROM_ENERGY_COUNT     1               // Address for the energy counter (4 bytes)

								#define EEPROM_CUSTOM_RESET     5               // Address for the reset reason (1 byte)

								#define EEPROM_DATA_END         6               // End of custom EEPROM data block


								//--------------------------------------------------------------------------------

								// HEARTBEAT

								//--------------------------------------------------------------------------------


								#define HEARTBEAT_INTERVAL          300000      // Interval between heartbeat messages (in ms)


								// Topics that will be reported in heartbeat

								#define HEARTBEAT_REPORT_STATUS     1

								#define HEARTBEAT_REPORT_IP         1

								#define HEARTBEAT_REPORT_MAC        1

								#define HEARTBEAT_REPORT_RSSI       1

								#define HEARTBEAT_REPORT_UPTIME     1

								#define HEARTBEAT_REPORT_FREEHEAP   1

								#define HEARTBEAT_REPORT_VCC        1

								#define HEARTBEAT_REPORT_RELAY      1

								#define HEARTBEAT_REPORT_COLOR      1

								#define HEARTBEAT_REPORT_HOSTNAME   1

								#define HEARTBEAT_REPORT_APP        1

								#define HEARTBEAT_REPORT_VERSION    1

								#define HEARTBEAT_REPORT_INTERVAL   0


								//--------------------------------------------------------------------------------

								// RESET

								//--------------------------------------------------------------------------------


								#define CUSTOM_RESET_HARDWARE   1               // Reset from hardware button

								#define CUSTOM_RESET_WEB        2               // Reset from web interface

								#define CUSTOM_RESET_TERMINAL   3               // Reset from terminal

								#define CUSTOM_RESET_MQTT       4               // Reset via MQTT

								#define CUSTOM_RESET_RPC        5               // Reset via RPC (HTTP)

								#define CUSTOM_RESET_OTA        6               // Reset after successful OTA update

								#define CUSTOM_RESET_NOFUSS     8               // Reset after successful NOFUSS update

								#define CUSTOM_RESET_UPGRADE    9               // Reset after update from web interface

								#define CUSTOM_RESET_FACTORY    10              // Factory reset from terminal


								#define CUSTOM_RESET_MAX        10


								#include <pgmspace.h>


								PROGMEM const char custom_reset_hardware[] = "Hardware button";

								PROGMEM const char custom_reset_web[] = "Reset from web interface";

								PROGMEM const char custom_reset_terminal[] = "Reset from terminal";

								PROGMEM const char custom_reset_mqtt[] = "Reset from MQTT";

								PROGMEM const char custom_reset_rpc[] = "Reset from RPC";

								PROGMEM const char custom_reset_ota[] = "Reset after successful OTA update";

								PROGMEM const char custom_reset_nofuss[] = "Reset after successful NoFUSS update";

								PROGMEM const char custom_reset_upgrade[] = "Reset after successful web update";

								PROGMEM const char custom_reset_factory[] = "Factory reset";

								PROGMEM const char* const custom_reset_string[] = {

								    custom_reset_hardware, custom_reset_web, custom_reset_terminal,

								    custom_reset_mqtt, custom_reset_rpc, custom_reset_ota,

								    custom_reset_nofuss, custom_reset_upgrade, custom_reset_factory

								};


								//--------------------------------------------------------------------------------

								// BUTTON

								//--------------------------------------------------------------------------------


								#define BUTTON_DEBOUNCE_DELAY       50          // Debounce delay (ms)

								#define BUTTON_DBLCLICK_DELAY       500         // Time in ms to wait for a second (or third...) click

								#define BUTTON_LNGCLICK_DELAY       1000        // Time in ms holding the button down to get a long click

								#define BUTTON_LNGLNGCLICK_DELAY    10000       // Time in ms holding the button down to get a long-long click


								#define BUTTON_EVENT_NONE           0

								#define BUTTON_EVENT_PRESSED        1

								#define BUTTON_EVENT_RELEASED       2

								#define BUTTON_EVENT_CLICK          2

								#define BUTTON_EVENT_DBLCLICK       3

								#define BUTTON_EVENT_LNGCLICK       4

								#define BUTTON_EVENT_LNGLNGCLICK    5


								#define BUTTON_MODE_NONE            0

								#define BUTTON_MODE_TOGGLE          1

								#define BUTTON_MODE_ON              2

								#define BUTTON_MODE_OFF             3

								#define BUTTON_MODE_AP              4

								#define BUTTON_MODE_RESET           5

								#define BUTTON_MODE_PULSE           6

								#define BUTTON_MODE_FACTORY         7


								//--------------------------------------------------------------------------------

								// RELAY

								//--------------------------------------------------------------------------------


								#define RELAY_MODE_OFF          0

								#define RELAY_MODE_ON           1

								#define RELAY_MODE_SAME         2

								#define RELAY_MODE_TOOGLE       3


								#define RELAY_SYNC_ANY          0

								#define RELAY_SYNC_NONE_OR_ONE  1

								#define RELAY_SYNC_ONE          2

								#define RELAY_SYNC_SAME         3


								#define RELAY_PULSE_NONE        0

								#define RELAY_PULSE_OFF         1

								#define RELAY_PULSE_ON          2


								#define RELAY_PROVIDER_RELAY    0

								#define RELAY_PROVIDER_DUAL     1

								#define RELAY_PROVIDER_LIGHT    2


								// Pulse time in milliseconds

								#define RELAY_PULSE_TIME        1.0


								// 0 means OFF, 1 ON and 2 whatever was before

								#define RELAY_MODE         		RELAY_MODE_OFF


								// 0 means ANY, 1 zero or one and 2 one and only one

								#define RELAY_SYNC         		RELAY_SYNC_ANY


								// 0 means no pulses, 1 means normally off, 2 normally on

								#define RELAY_PULSE_MODE     	RELAY_PULSE_NONE


								// Relay requests flood protection window - in seconds

								#define RELAY_FLOOD_WINDOW      3


								// Allowed actual relay changes inside requests flood protection window

								#define RELAY_FLOOD_CHANGES     5


								//--------------------------------------------------------------------------------

								// I18N

								//--------------------------------------------------------------------------------


								#define TMP_CELSIUS             0

								#define TMP_FAHRENHEIT          1

								#define TMP_UNITS               TMP_CELSIUS // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)


								//--------------------------------------------------------------------------------

								// LED

								//--------------------------------------------------------------------------------


								// All defined LEDs in the board can be managed through MQTT

								// except the first one when LED_AUTO is set to 1.

								// If LED_AUTO is set to 1 the board will use first defined LED to show wifi status.

								#define LED_AUTO                1


								// -----------------------------------------------------------------------------

								// WIFI & WEB

								// -----------------------------------------------------------------------------


								#define WIFI_CONNECT_TIMEOUT    30000       // Connecting timeout for WIFI in ms

								#define WIFI_RECONNECT_INTERVAL 120000      // If could not connect to WIFI, retry after this time in ms

								#define WIFI_MAX_NETWORKS       5           // Max number of WIFI connection configurations

								#define HTTP_USERNAME           "admin"     // HTTP username

								#define ADMIN_PASS              "fibonacci" // Default password

								#define FORCE_CHANGE_PASS       1           // Force the user to change the password if default one

								#define WS_BUFFER_SIZE          5           // Max number of secured websocket connections

								#define WS_TIMEOUT              1800000     // Timeout for secured websocket

								#define WEBSERVER_PORT          80          // HTTP port

								#define DNS_PORT                53          // MDNS port

								#define ENABLE_MDNS             1           // Enabled MDNS


								#define WEB_MODE_NORMAL         0

								#define WEB_MODE_PASSWORD       1


								#define AP_MODE                 AP_MODE_ALONE


								// This option builds the firmware with the web interface embedded.

								#ifndef EMBEDDED_WEB

								#define EMBEDDED_WEB            1

								#endif


								// -----------------------------------------------------------------------------

								// OTA & NOFUSS

								// -----------------------------------------------------------------------------


								#define OTA_PORT                8266        // OTA port

								#define NOFUSS_SERVER           ""          // Default NoFuss Server

								#define NOFUSS_INTERVAL         3600000     // Check for updates every hour


								// -----------------------------------------------------------------------------

								// MQTT

								// -----------------------------------------------------------------------------


								#ifndef MQTT_USE_ASYNC

								#define MQTT_USE_ASYNC          1           // Use AysncMQTTClient (1) or PubSubClient (0)

								#endif


								#define MQTT_SERVER             ""          // Default MQTT broker address

								#define MQTT_PORT               1883        // MQTT broker port

								#define MQTT_TOPIC              "/test/switch/{identifier}"     // Default MQTT base topic

								#define MQTT_RETAIN             true        // MQTT retain flag

								#define MQTT_QOS                0           // MQTT QoS value for all messages

								#define MQTT_KEEPALIVE          30          // MQTT keepalive value

								#define MQTT_RECONNECT_DELAY    10000       // Try to reconnect after 10s

								#define MQTT_TRY_INTERVAL       30000       // Timeframe for disconnect retries

								#define MQTT_MAX_TRIES          12          // After these many retries during the previous MQTT_TRY_INTERVAL the board will reset

								#define MQTT_SKIP_RETAINED      1           // Skip retained messages on connection

								#define MQTT_SKIP_TIME          1000        // Skip messages for 1 second anter connection


								#define MQTT_USE_JSON           0           // Group messages in a JSON body

								#define MQTT_USE_JSON_DELAY     100         // Wait this many ms before grouping messages


								// These particles will be concatenated to the MQTT_TOPIC base to form the actual topic

								#define MQTT_TOPIC_JSON         "data"

								#define MQTT_TOPIC_ACTION       "action"

								#define MQTT_TOPIC_RELAY        "relay"

								#define MQTT_TOPIC_LED          "led"

								#define MQTT_TOPIC_COLOR        "color"

								#define MQTT_TOPIC_BRIGHTNESS   "brightness"

								#define MQTT_TOPIC_COLORTEMP    "color/temperature"

								#define MQTT_TOPIC_BUTTON       "button"

								#define MQTT_TOPIC_IP           "ip"

								#define MQTT_TOPIC_VERSION      "version"

								#define MQTT_TOPIC_UPTIME       "uptime"

								#define MQTT_TOPIC_FREEHEAP     "freeheap"

								#define MQTT_TOPIC_VCC          "vcc"

								#define MQTT_TOPIC_STATUS       "status"

								#define MQTT_TOPIC_MAC          "mac"

								#define MQTT_TOPIC_RSSI         "rssi"

								#define MQTT_TOPIC_APP          "app"

								#define MQTT_TOPIC_INTERVAL     "interval"

								#define MQTT_TOPIC_HOSTNAME     "host"

								#define MQTT_TOPIC_TIME         "time"

								#define MQTT_TOPIC_ANALOG       "analog"


								#define MQTT_STATUS_ONLINE      "1"         // Value for the device ON message

								#define MQTT_STATUS_OFFLINE     "0"         // Value for the device OFF message (will)


								#define MQTT_ACTION_RESET       "reset"     // RESET MQTT topic particle


								// Internal MQTT events (do not change)

								#define MQTT_CONNECT_EVENT      0

								#define MQTT_DISCONNECT_EVENT   1

								#define MQTT_MESSAGE_EVENT      2


								// Custom get and set postfixes

								// Use something like "/status" or "/set", with leading slash

								#define MQTT_USE_GETTER         ""

								#define MQTT_USE_SETTER         "/set"


								// -----------------------------------------------------------------------------

								// I2C

								// -----------------------------------------------------------------------------


								#define ENABLE_I2C              0           // I2C enabled

								#define I2C_SDA_PIN             4           // SDA GPIO

								#define I2C_SCL_PIN             14          // SCL GPIO

								#define I2C_CLOCK_STRETCH_TIME  200         // BRZO clock stretch time

								#define I2C_SCL_FREQUENCY       1000        // BRZO SCL frequency


								// -----------------------------------------------------------------------------

								// LIGHT

								// -----------------------------------------------------------------------------


								#define ENABLE_GAMMA_CORRECTION 0


								#define LIGHT_PROVIDER_NONE     0

								#define LIGHT_PROVIDER_WS2812   1

								#define LIGHT_PROVIDER_RGB      2

								#define LIGHT_PROVIDER_RGBW     3

								#define LIGHT_PROVIDER_MY9192   4

								#define LIGHT_PROVIDER_RGB2W    5


								#define LIGHT_DEFAULT_COLOR     "#000080"

								#define LIGHT_SAVE_DELAY        5

								#define LIGHT_MAX_VALUE         255

								#define LIGHT_MAX_BRIGHTNESS    LIGHT_MAX_VALUE


								// Settings for MY9291 bulbs (AI Light)

								#define MY9291_DI_PIN           13

								#define MY9291_DCKI_PIN         15

								#define MY9291_COMMAND          MY9291_COMMAND_DEFAULT


								// Shared settings between RGB and RGBW lights

								#define RGBW_INVERSE_LOGIC      1

								#define RGBW_RED_PIN            14

								#define RGBW_GREEN_PIN          5

								#define RGBW_BLUE_PIN           12

								#define RGBW_WHITE_PIN          13


								// -----------------------------------------------------------------------------

								// DOMOTICZ

								// -----------------------------------------------------------------------------


								#ifndef ENABLE_DOMOTICZ

								#define ENABLE_DOMOTICZ         1               // Enable Domoticz support by default

								#endif

								#define DOMOTICZ_IN_TOPIC       "domoticz/in"   // Default subscription topic

								#define DOMOTICZ_OUT_TOPIC      "domoticz/out"  // Default publication topic


								// -----------------------------------------------------------------------------

								// INFLUXDB

								// -----------------------------------------------------------------------------


								#ifndef ENABLE_INFLUXDB

								#define ENABLE_INFLUXDB         1               // Enable InfluxDB support by default

								#endif

								#define INFLUXDB_PORT           8086            // Default InfluxDB port


								// -----------------------------------------------------------------------------

								// NTP

								// -----------------------------------------------------------------------------


								#define NTP_SERVER              "pool.ntp.org"  // Default NTP server

								#define NTP_TIME_OFFSET         1               // Default timezone offset (GMT+1)

								#define NTP_DAY_LIGHT           true            // Enable daylight time saving by default

								#define NTP_UPDATE_INTERVAL     1800            // NTP check every 30 minutes


								// -----------------------------------------------------------------------------

								// FAUXMO

								// -----------------------------------------------------------------------------


								// This setting defines whether Alexa support should be built into the firmware

								#ifndef ENABLE_FAUXMO

								#define ENABLE_FAUXMO       1

								#endif


								// This is default value for the fauxmoEnabled setting that defines whether

								// this device should be discoberable and respond to Alexa commands.

								// Both ENABLE_FAUXMO and fauxmoEnabled should be 1 for Alexa support to work.

								#define FAUXMO_ENABLED          1