mh
/
mhsw-espurna


								// =============================================================================

								// SENSORS - General data

								// =============================================================================


								#define SENSOR_DEBUG                        0               // Debug sensors


								#define SENSOR_READ_INTERVAL                6               // Read data from sensors every 6 seconds

								#define SENSOR_READ_MIN_INTERVAL            6               // Minimum read interval

								#define SENSOR_READ_MAX_INTERVAL            3600            // Maximum read interval

								#define SENSOR_INIT_INTERVAL                10000           // Try to re-init non-ready sensors every 10s


								#define SENSOR_REPORT_EVERY                 10              // Report every this many readings

								#define SENSOR_REPORT_MIN_EVERY             1               // Minimum every value

								#define SENSOR_REPORT_MAX_EVERY             12              // Maximum


								#define SENSOR_USE_INDEX                    0               // Use the index in topic (i.e. temperature/0)

								                                                            // even if just one sensor (0 for backwards compatibility)


								#ifndef SENSOR_POWER_CHECK_STATUS

								#define SENSOR_POWER_CHECK_STATUS           1               // If set to 1 the reported power/current/energy will be 0 if the relay[0] is OFF

								#endif


								#ifndef SENSOR_TEMPERATURE_CORRECTION

								#define SENSOR_TEMPERATURE_CORRECTION       0.0             // Offset correction

								#endif


								#ifndef TEMPERATURE_MIN_CHANGE

								#define TEMPERATURE_MIN_CHANGE              0.0             // Minimum temperature change to report

								#endif


								#ifndef SENSOR_HUMIDITY_CORRECTION

								#define SENSOR_HUMIDITY_CORRECTION          0.0             // Offset correction

								#endif


								#ifndef HUMIDITY_MIN_CHANGE

								#define HUMIDITY_MIN_CHANGE                 0               // Minimum humidity change to report

								#endif


								#define SENSOR_PUBLISH_ADDRESSES            0               // Publish sensor addresses

								#define SENSOR_ADDRESS_TOPIC                "address"       // Topic to publish sensor addresses


								#ifndef SENSOR_TEMPERATURE_UNITS

								#define SENSOR_TEMPERATURE_UNITS            TMP_CELSIUS     // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)

								#endif


								#ifndef SENSOR_ENERGY_UNITS

								#define SENSOR_ENERGY_UNITS                 ENERGY_JOULES   // Energy units (ENERGY_JOULES | ENERGY_KWH)

								#endif


								#ifndef SENSOR_POWER_UNITS

								#define SENSOR_POWER_UNITS                  POWER_WATTS     // Power units (POWER_WATTS | POWER_KILOWATTS)

								#endif


								// =============================================================================

								// Specific data for each sensor

								// =============================================================================


								//------------------------------------------------------------------------------

								// AM2320 Humidity & Temperature sensor over I2C

								// Enable support by passing AM2320_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef AM2320_SUPPORT

								#define AM2320_SUPPORT                  0

								#endif


								#ifndef AM2320_ADDRESS

								#define AM2320_ADDRESS                  0x00    // 0x00 means auto

								#endif


								//------------------------------------------------------------------------------

								// Analog sensor

								// Enable support by passing ANALOG_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef ANALOG_SUPPORT

								#define ANALOG_SUPPORT                  0

								#endif


								//------------------------------------------------------------------------------

								// BH1750

								// Enable support by passing BH1750_SUPPORT=1 build flag

								// http://www.elechouse.com/elechouse/images/product/Digital%20light%20Sensor/bh1750fvi-e.pdf

								//------------------------------------------------------------------------------


								#ifndef BH1750_SUPPORT

								#define BH1750_SUPPORT                  0

								#endif


								#ifndef BH1750_ADDRESS

								#define BH1750_ADDRESS                  0x00    // 0x00 means auto

								#endif


								#define BH1750_MODE                     BH1750_CONTINUOUS_HIGH_RES_MODE


								//------------------------------------------------------------------------------

								// BME280/BMP280

								// Enable support by passing BMX280_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef BMX280_SUPPORT

								#define BMX280_SUPPORT                  0

								#endif


								#ifndef BMX280_ADDRESS

								#define BMX280_ADDRESS                  0x00    // 0x00 means auto

								#endif


								#define BMX280_MODE                     1       // 0 for sleep mode, 1 or 2 for forced mode, 3 for normal mode

								#define BMX280_STANDBY                  0       // 0 for 0.5ms, 1 for 62.5ms, 2 for 125ms

								                                                // 3 for 250ms, 4 for 500ms, 5 for 1000ms

								                                                // 6 for 10ms, 7 for 20ms

								#define BMX280_FILTER                   0       // 0 for OFF, 1 for 2 values, 2 for 4 values, 3 for 8 values and 4 for 16 values

								#define BMX280_TEMPERATURE              1       // Oversampling for temperature (set to 0 to disable magnitude)

								#define BMX280_HUMIDITY                 1       // Oversampling for humidity (set to 0 to disable magnitude, only for BME280)

								#define BMX280_PRESSURE                 1       // Oversampling for pressure (set to 0 to disable magnitude)


								//------------------------------------------------------------------------------

								// Dallas OneWire temperature sensors

								// Enable support by passing DALLAS_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef DALLAS_SUPPORT

								#define DALLAS_SUPPORT                  0

								#endif


								#ifndef DALLAS_PIN

								#define DALLAS_PIN                      14

								#endif


								#define DALLAS_RESOLUTION               9           // Not used atm

								#define DALLAS_READ_INTERVAL            2000        // Force sensor read & cache every 2 seconds


								//------------------------------------------------------------------------------

								// DHTXX temperature/humidity sensor

								// Enable support by passing DHT_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef DHT_SUPPORT

								#define DHT_SUPPORT                     0

								#endif


								#ifndef DHT_PIN

								#define DHT_PIN                         14

								#endif


								#ifndef DHT_TYPE

								#define DHT_TYPE                        DHT_CHIP_DHT22

								#endif


								//------------------------------------------------------------------------------

								// CSE7766 based power sensor

								// Enable support by passing CSE7766_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef CSE7766_SUPPORT

								#define CSE7766_SUPPORT                 0

								#endif


								#ifndef CSE7766_PIN

								#define CSE7766_PIN                     1       // TX pin from the CSE7766

								#endif


								#ifndef CSE7766_PIN_INVERSE

								#define CSE7766_PIN_INVERSE             0       // Signal is inverted

								#endif


								#define CSE7766_SYNC_INTERVAL           300     // Safe time between transmissions (ms)

								#define CSE7766_BAUDRATE                4800    // UART baudrate


								#define CSE7766_V1R                     1.0     // 1mR current resistor

								#define CSE7766_V2R                     1.0     // 1M voltage resistor


								//------------------------------------------------------------------------------

								// Digital sensor

								// Enable support by passing DIGITAL_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef DIGITAL_SUPPORT

								#define DIGITAL_SUPPORT                 0

								#endif


								#ifndef DIGITAL_PIN

								#define DIGITAL_PIN                     2

								#endif


								#ifndef DIGITAL_PIN_MODE

								#define DIGITAL_PIN_MODE                INPUT_PULLUP

								#endif


								#ifndef DIGITAL_DEFAULT_STATE

								#define DIGITAL_DEFAULT_STATE           1

								#endif


								//------------------------------------------------------------------------------

								// ECH1560 based power sensor

								// Enable support by passing ECH1560_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef ECH1560_SUPPORT

								#define ECH1560_SUPPORT                 0

								#endif


								#ifndef ECH1560_CLK_PIN

								#define ECH1560_CLK_PIN                 4       // CLK pin for the ECH1560

								#endif


								#ifndef ECH1560_MISO_PIN

								#define ECH1560_MISO_PIN                5       // MISO pin for the ECH1560

								#endif


								#ifndef ECH1560_INVERTED

								#define ECH1560_INVERTED                0       // Signal is inverted

								#endif


								//------------------------------------------------------------------------------

								// Energy Monitor general settings

								//------------------------------------------------------------------------------


								#define EMON_MAX_SAMPLES                1000        // Max number of samples to get

								#define EMON_MAX_TIME                   250         // Max time in ms to sample

								#define EMON_FILTER_SPEED               512         // Mobile average filter speed

								#define EMON_MAINS_VOLTAGE              230         // Mains voltage

								#define EMON_REFERENCE_VOLTAGE          3.3         // Reference voltage of the ADC

								#define EMON_CURRENT_RATIO              30          // Current ratio in the clamp (30V/1A)

								#define EMON_REPORT_CURRENT             0           // Report current

								#define EMON_REPORT_POWER               1           // Report power

								#define EMON_REPORT_ENERGY              1           // Report energy


								//------------------------------------------------------------------------------

								// Energy Monitor based on ADC121

								// Enable support by passing EMON_ADC121_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef EMON_ADC121_SUPPORT

								#define EMON_ADC121_SUPPORT             0       // Do not build support by default

								#endif


								#define EMON_ADC121_I2C_ADDRESS         0x00    // 0x00 means auto


								//------------------------------------------------------------------------------

								// Energy Monitor based on ADS1X15

								// Enable support by passing EMON_ADS1X15_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef EMON_ADS1X15_SUPPORT

								#define EMON_ADS1X15_SUPPORT            0       // Do not build support by default

								#endif


								#define EMON_ADS1X15_I2C_ADDRESS        0x00    // 0x00 means auto

								#define EMON_ADS1X15_TYPE               ADS1X15_CHIP_ADS1115

								#define EMON_ADS1X15_GAIN               ADS1X15_REG_CONFIG_PGA_4_096V

								#define EMON_ADS1X15_MASK               0x0F    // A0=1 A1=2 A2=4 A3=8


								//------------------------------------------------------------------------------

								// Energy Monitor based on interval analog GPIO

								// Enable support by passing EMON_ANALOG_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef EMON_ANALOG_SUPPORT

								#define EMON_ANALOG_SUPPORT             0       // Do not build support by default

								#endif


								//------------------------------------------------------------------------------

								// Counter sensor

								// Enable support by passing EVENTS_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef EVENTS_SUPPORT

								#define EVENTS_SUPPORT                  0       // Do not build with counter support by default

								#endif


								#ifndef EVENTS_PIN

								#define EVENTS_PIN                      2       // GPIO to monitor

								#endif


								#ifndef EVENTS_PIN_MODE

								#define EVENTS_PIN_MODE                 INPUT   // INPUT, INPUT_PULLUP

								#endif


								#ifndef EVENTS_INTERRUPT_MODE

								#define EVENTS_INTERRUPT_MODE           RISING  // RISING, FALLING, BOTH

								#endif


								#define EVENTS_DEBOUNCE                 50      // Do not register events within less than 10 millis


								//------------------------------------------------------------------------------

								// GUVAS12SD UV Sensor (analog)

								// Enable support by passing GUVAS12SD_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef GUVAS12SD_SUPPORT

								#define GUVAS12SD_SUPPORT               0

								#endif


								#ifndef GUVAS12SD_PIN

								#define GUVAS12SD_PIN                   14

								#endif


								//------------------------------------------------------------------------------

								// HC-SR04

								// Enable support by passing HCSR04_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef HCSR04_SUPPORT

								#define HCSR04_SUPPORT                  0

								#endif


								#ifndef HCSR04_TRIGGER

								#define HCSR04_TRIGGER                  12      // GPIO for the trigger pin (output)

								#endif


								#ifndef HCSR04_ECHO

								#define HCSR04_ECHO                     14      // GPIO for the echo pin (input)

								#endif


								//------------------------------------------------------------------------------

								// HLW8012 Energy monitor IC

								// Enable support by passing HLW8012_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef HLW8012_SUPPORT

								#define HLW8012_SUPPORT                 0

								#endif


								#ifndef HLW8012_SEL_PIN

								#define HLW8012_SEL_PIN                 5

								#endif


								#ifndef HLW8012_CF1_PIN

								#define HLW8012_CF1_PIN                 13

								#endif


								#ifndef HLW8012_CF_PIN

								#define HLW8012_CF_PIN                  14

								#endif


								#ifndef HLW8012_SEL_CURRENT

								#define HLW8012_SEL_CURRENT             HIGH    // SEL pin to HIGH to measure current

								#endif


								#ifndef HLW8012_CURRENT_R

								#define HLW8012_CURRENT_R               0.001   // Current resistor

								#endif


								#ifndef HLW8012_VOLTAGE_R_UP

								#define HLW8012_VOLTAGE_R_UP            ( 5 * 470000 )  // Upstream voltage resistor

								#endif


								#ifndef HLW8012_VOLTAGE_R_DOWN

								#define HLW8012_VOLTAGE_R_DOWN          ( 1000 )        // Downstream voltage resistor

								#endif


								#define HLW8012_USE_INTERRUPTS          1       // Use interrupts to trap HLW8012 signals


								//------------------------------------------------------------------------------

								// MHZ19 CO2 sensor

								// Enable support by passing MHZ19_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef MHZ19_SUPPORT

								#define MHZ19_SUPPORT                   0

								#endif


								#ifndef MHZ19_RX_PIN

								#define MHZ19_RX_PIN                    13

								#endif


								#ifndef MHZ19_TX_PIN

								#define MHZ19_TX_PIN                    15

								#endif


								//------------------------------------------------------------------------------

								// SenseAir CO2 sensor

								// Enable support by passing SENSEAIR_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef SENSEAIR_SUPPORT

								#define SENSEAIR_SUPPORT                0

								#endif


								#ifndef SENSEAIR_RX_PIN

								#define SENSEAIR_RX_PIN                 0

								#endif


								#ifndef SENSEAIR_TX_PIN

								#define SENSEAIR_TX_PIN                 2

								#endif


								//------------------------------------------------------------------------------

								// Particle Monitor based on Plantower PMS

								// Enable support by passing PMS_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef PMSX003_SUPPORT

								#define PMSX003_SUPPORT                 0

								#endif


								#ifndef PMS_TYPE

								#define PMS_TYPE                        PMS_TYPE_X003

								#endif


								// You can enable smart sleep (read 6-times then sleep on 24-reading-cycles) to extend PMS sensor's life.

								// Otherwise the default lifetime of PMS sensor is about 8000-hours/1-years.

								// The PMS's fan will stop working on sleeping cycle, and will wake up on reading cycle.

								#ifndef PMS_SMART_SLEEP

								#define PMS_SMART_SLEEP                 0

								#endif


								#ifndef PMS_RX_PIN

								#define PMS_RX_PIN                      13

								#endif


								#ifndef PMS_TX_PIN

								#define PMS_TX_PIN                      15

								#endif


								//------------------------------------------------------------------------------

								// PZEM004T based power monitor

								// Enable support by passing PZEM004T_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef PZEM004T_SUPPORT

								#define PZEM004T_SUPPORT                0

								#endif


								#ifndef PZEM004T_USE_SOFT

								#define PZEM004T_USE_SOFT               1       // Use software serial

								#endif


								#ifndef PZEM004T_RX_PIN

								#define PZEM004T_RX_PIN                 13      // Software serial RX GPIO (if PZEM004T_USE_SOFT == 1)

								#endif


								#ifndef PZEM004T_TX_PIN

								#define PZEM004T_TX_PIN                 15      // Software serial TX GPIO (if PZEM004T_USE_SOFT == 1)

								#endif


								#ifndef PZEM004T_HW_PORT

								#define PZEM004T_HW_PORT                Serial1 // Hardware serial port (if PZEM004T_USE_SOFT == 0)

								#endif


								//------------------------------------------------------------------------------

								// SHT3X I2C (Wemos) temperature & humidity sensor

								// Enable support by passing SHT3X_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef SHT3X_I2C_SUPPORT

								#define SHT3X_I2C_SUPPORT               0

								#endif


								#ifndef SHT3X_I2C_ADDRESS

								#define SHT3X_I2C_ADDRESS               0x00    // 0x00 means auto

								#endif


								//------------------------------------------------------------------------------

								// SI7021 temperature & humidity sensor

								// Enable support by passing SI7021_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef SI7021_SUPPORT

								#define SI7021_SUPPORT                  0

								#endif


								#ifndef SI7021_ADDRESS

								#define SI7021_ADDRESS                  0x00    // 0x00 means auto

								#endif


								//------------------------------------------------------------------------------

								// TMP3X analog temperature sensor

								// Enable support by passing TMP3X_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef TMP3X_SUPPORT

								#define TMP3X_SUPPORT                   0

								#endif


								#ifndef TMP3X_TYPE

								#define TMP3X_TYPE                      TMP3X_TMP35

								#endif


								//------------------------------------------------------------------------------

								// V9261F based power sensor

								// Enable support by passing SI7021_SUPPORT=1 build flag

								//------------------------------------------------------------------------------


								#ifndef V9261F_SUPPORT

								#define V9261F_SUPPORT                  0

								#endif


								#ifndef V9261F_PIN

								#define V9261F_PIN                      2       // TX pin from the V9261F

								#endif


								#ifndef V9261F_PIN_INVERSE

								#define V9261F_PIN_INVERSE              1       // Signal is inverted

								#endif


								#define V9261F_SYNC_INTERVAL            600     // Sync signal length (ms)

								#define V9261F_BAUDRATE                 4800    // UART baudrate


								// Default ratios

								#define V9261F_CURRENT_FACTOR           79371434.0

								#define V9261F_VOLTAGE_FACTOR           4160651.0

								#define V9261F_POWER_FACTOR             153699.0

								#define V9261F_RPOWER_FACTOR            V9261F_CURRENT_FACTOR


								// =============================================================================

								// Sensor helpers configuration - can't move to dependencies.h

								// =============================================================================


								#ifndef SENSOR_SUPPORT

								#define SENSOR_SUPPORT ( \

								    AM2320_SUPPORT || \

								    ANALOG_SUPPORT || \

								    BH1750_SUPPORT || \

								    BMX280_SUPPORT || \

								    CSE7766_SUPPORT || \

								    DALLAS_SUPPORT || \

								    DHT_SUPPORT || \

								    DIGITAL_SUPPORT || \

								    ECH1560_SUPPORT || \

								    EMON_ADC121_SUPPORT || \

								    EMON_ADS1X15_SUPPORT || \

								    EMON_ANALOG_SUPPORT || \

								    EVENTS_SUPPORT || \

								    GUVAS12SD_SUPPORT || \

								    HCSR04_SUPPORT || \

								    HLW8012_SUPPORT || \

								    MHZ19_SUPPORT || \

								    SENSEAIR_SUPPORT || \

								    PMSX003_SUPPORT || \

								    PZEM004T_SUPPORT || \

								    SHT3X_I2C_SUPPORT || \

								    SI7021_SUPPORT || \

								    TMP3X_SUPPORT || \

								    V9261F_SUPPORT \

								)

								#endif


								// -----------------------------------------------------------------------------

								// ADC

								// -----------------------------------------------------------------------------


								// Default ADC mode is to monitor internal power supply

								#ifndef ADC_MODE_VALUE

								#define ADC_MODE_VALUE                  ADC_VCC

								#endif


								// -----------------------------------------------------------------------------

								// I2C

								// -----------------------------------------------------------------------------


								#ifndef I2C_SUPPORT

								#define I2C_SUPPORT                     0       // I2C enabled (1.98Kb)

								#endif


								#define I2C_USE_BRZO                    0       // Use brzo_i2c library or standard Wire


								#ifndef I2C_SDA_PIN

								#define I2C_SDA_PIN                     SDA     // SDA GPIO (Sonoff => 4)

								#endif


								#ifndef I2C_SCL_PIN

								#define I2C_SCL_PIN                     SCL     // SCL GPIO (Sonoff => 14)

								#endif


								#define I2C_CLOCK_STRETCH_TIME          200     // BRZO clock stretch time

								#define I2C_SCL_FREQUENCY               1000    // BRZO SCL frequency

								#define I2C_CLEAR_BUS                   0       // Clear I2C bus on boot

								#define I2C_PERFORM_SCAN                1       // Perform a bus scan on boot


								//--------------------------------------------------------------------------------

								// Class loading

								//--------------------------------------------------------------------------------


								#if SENSOR_SUPPORT


								#include "../sensors/BaseSensor.h"


								#if AM2320_SUPPORT

								    #include "../sensors/AM2320Sensor.h"

								#endif


								#if ANALOG_SUPPORT

								    #include "../sensors/AnalogSensor.h"

								#endif


								#if BH1750_SUPPORT

								    #include "../sensors/BH1750Sensor.h"

								#endif


								#if BMX280_SUPPORT

								    #include "../sensors/BMX280Sensor.h"

								#endif


								#if CSE7766_SUPPORT

								    #include <SoftwareSerial.h>

								    #include "../sensors/CSE7766Sensor.h"

								#endif


								#if DALLAS_SUPPORT

								    #include <OneWire.h>

								    #include "../sensors/DallasSensor.h"

								#endif


								#if DHT_SUPPORT

								    #include "../sensors/DHTSensor.h"

								#endif


								#if DIGITAL_SUPPORT

								    #include "../sensors/DigitalSensor.h"

								#endif


								#if ECH1560_SUPPORT

								    #include "../sensors/ECH1560Sensor.h"

								#endif


								#if EMON_ADC121_SUPPORT

								    #include "../sensors/EmonADC121Sensor.h"

								#endif


								#if EMON_ADS1X15_SUPPORT

								    #include "../sensors/EmonADS1X15Sensor.h"

								#endif


								#if EMON_ANALOG_SUPPORT

								    #include "../sensors/EmonAnalogSensor.h"

								#endif


								#if EVENTS_SUPPORT

								    #include "../sensors/EventSensor.h"

								#endif


								#if GUVAS12SD_SUPPORT

								    #include "../sensors/GUVAS12SDSensor.h"

								#endif


								#if HCSR04_SUPPORT

								    #include "../sensors/HCSR04Sensor.h"

								#endif


								#if HLW8012_SUPPORT

								    #include <HLW8012.h>

								    #include "../sensors/HLW8012Sensor.h"

								#endif


								#if MHZ19_SUPPORT

								    #include <SoftwareSerial.h>

								    #include "../sensors/MHZ19Sensor.h"

								#endif


								#if SENSEAIR_SUPPORT

								    #include <SoftwareSerial.h>

								    #include "../sensors/SenseAirSensor.h"

								#endif


								#if PMSX003_SUPPORT

								    #include <SoftwareSerial.h>

								    #include "../sensors/PMSX003Sensor.h"

								#endif


								#if PZEM004T_SUPPORT

								    #include <SoftwareSerial.h>

								    #include "../sensors/PZEM004TSensor.h"

								#endif


								#if SI7021_SUPPORT

								    #include "../sensors/SI7021Sensor.h"

								#endif


								#if SHT3X_I2C_SUPPORT

								    #include "../sensors/SHT3XI2CSensor.h"

								#endif


								#if TMP3X_SUPPORT

								    #include "../sensors/TMP3XSensor.h"

								#endif


								#if V9261F_SUPPORT

								    #include <SoftwareSerial.h>

								    #include "../sensors/V9261FSensor.h"

								#endif


								#endif // SENSOR_SUPPORT