You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
1827 lines
62 KiB
1827 lines
62 KiB
//------------------------------------------------------------------------------
|
|
// Do not change this file unless you know what you are doing
|
|
// To override user configuration, please see custom.h
|
|
//------------------------------------------------------------------------------
|
|
|
|
#pragma once
|
|
|
|
//------------------------------------------------------------------------------
|
|
// GENERAL
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef DEVICE_NAME
|
|
#define DEVICE_NAME MANUFACTURER "_" DEVICE // Concatenate both to get a unique device name
|
|
#endif
|
|
|
|
// When defined, ADMIN_PASS must be 8..63 printable ASCII characters. See:
|
|
// https://en.wikipedia.org/wiki/Wi-Fi_Protected_Access#Target_users_(authentication_key_distribution)
|
|
// https://github.com/xoseperez/espurna/issues/1151
|
|
#ifndef ADMIN_PASS
|
|
#define ADMIN_PASS "fibonacci" // Default password (WEB, OTA, WIFI SoftAP)
|
|
#endif
|
|
|
|
#ifndef USE_PASSWORD
|
|
#define USE_PASSWORD 1 // Insecurity caution! Disabling this will disable password querying completely.
|
|
#endif
|
|
|
|
#ifndef LOOP_DELAY_TIME
|
|
#define LOOP_DELAY_TIME 10 // Delay for the main loop, in millis [0-250]
|
|
// Recommended minimum is 10, see:
|
|
// https://github.com/xoseperez/espurna/issues/1541
|
|
// https://github.com/xoseperez/espurna/issues/1631
|
|
// https://github.com/esp8266/Arduino/issues/5825
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// HEARTBEAT
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef HEARTBEAT_MODE
|
|
#define HEARTBEAT_MODE HEARTBEAT_REPEAT
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_INTERVAL
|
|
#define HEARTBEAT_INTERVAL 300 // Interval between heartbeat messages
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// DEBUG
|
|
//------------------------------------------------------------------------------
|
|
|
|
// Set global logger mode. One of:
|
|
// - DebugLogMode::Enabled
|
|
// - DebugLogMode::Disabled
|
|
// - DebugLogMode::SkipBoot
|
|
|
|
#ifndef DEBUG_LOG_MODE
|
|
#define DEBUG_LOG_MODE DebugLogMode::Enabled
|
|
#endif
|
|
|
|
// Serial debug log
|
|
|
|
#ifndef DEBUG_SERIAL_SUPPORT
|
|
#define DEBUG_SERIAL_SUPPORT 1 // Enable serial debug log
|
|
#endif
|
|
|
|
#ifndef DEBUG_PORT
|
|
#define DEBUG_PORT Serial // Default debugging port
|
|
#endif
|
|
|
|
#ifndef SERIAL_BAUDRATE
|
|
#define SERIAL_BAUDRATE 115200 // Default baudrate
|
|
#endif
|
|
|
|
#ifndef DEBUG_ADD_TIMESTAMP
|
|
#define DEBUG_ADD_TIMESTAMP 1 // Add timestamp to debug messages
|
|
// (in millis overflowing every 1000 seconds)
|
|
#endif
|
|
|
|
// Second serial port (used for RX)
|
|
|
|
#ifndef SERIAL_RX_ENABLED
|
|
#define SERIAL_RX_ENABLED 0 // Secondary serial port for RX
|
|
#endif
|
|
|
|
#ifndef SERIAL_RX_PORT
|
|
#define SERIAL_RX_PORT Serial // This setting is usually defined
|
|
// in the hardware.h file for those
|
|
// boards that require it
|
|
#endif
|
|
|
|
#ifndef SERIAL_RX_BAUDRATE
|
|
#define SERIAL_RX_BAUDRATE 115200 // Default baudrate
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
// UDP debug log
|
|
// To receive the message on the destination computer use nc:
|
|
// nc -ul 8113
|
|
|
|
#ifndef DEBUG_UDP_SUPPORT
|
|
#define DEBUG_UDP_SUPPORT 0 // Enable UDP debug log
|
|
#endif
|
|
|
|
#ifndef DEBUG_UDP_IP
|
|
#define DEBUG_UDP_IP IPAddress(192, 168, 1, 100)
|
|
#endif
|
|
|
|
#ifndef DEBUG_UDP_PORT
|
|
#define DEBUG_UDP_PORT 514
|
|
#endif
|
|
|
|
// If DEBUG_UDP_PORT is set to 514 syslog format is assumed
|
|
// (https://tools.ietf.org/html/rfc3164)
|
|
// DEBUG_UDP_FAC_PRI is the facility+priority
|
|
#define DEBUG_UDP_FAC_PRI (SYSLOG_LOCAL0 | SYSLOG_DEBUG)
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef DEBUG_TELNET_SUPPORT
|
|
#define DEBUG_TELNET_SUPPORT 1 // Enable telnet debug log (will only work if TELNET_SUPPORT is also 1)
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef DEBUG_WEB_SUPPORT
|
|
#define DEBUG_WEB_SUPPORT 1 // Enable web debug log (will only work if WEB_SUPPORT is also 1)
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef DEBUG_LOG_BUFFER_SUPPORT
|
|
#define DEBUG_LOG_BUFFER_SUPPORT 1 // Support boot log buffer (1.2Kb)
|
|
// Will only work if DEBUG_LOG_BUFFER_ENABLED or runtime setting is also 1
|
|
#endif
|
|
|
|
#ifndef DEBUG_LOG_BUFFER_ENABLED
|
|
#define DEBUG_LOG_BUFFER_ENABLED 0 // Disable boot log buffer by default
|
|
#endif
|
|
|
|
#ifndef DEBUG_LOG_BUFFER_SIZE
|
|
#define DEBUG_LOG_BUFFER_SIZE 4096 // Store 4 Kb of log strings
|
|
// WARNING! Memory is only reclaimed after `debug.buffer` prints the buffer contents
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// TELNET
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef TELNET_SUPPORT
|
|
#define TELNET_SUPPORT 1 // Enable telnet support by default (3.34Kb)
|
|
#endif
|
|
|
|
#ifndef TELNET_STA
|
|
#define TELNET_STA 0 // By default, disallow connections via STA interface
|
|
#endif
|
|
|
|
#ifndef TELNET_AUTHENTICATION
|
|
#define TELNET_AUTHENTICATION 1 // Request password to start telnet session by default
|
|
#endif
|
|
|
|
#ifndef TELNET_PORT
|
|
#define TELNET_PORT 23 // Port to listen to telnet clients
|
|
#endif
|
|
|
|
#ifndef TELNET_MAX_CLIENTS
|
|
#define TELNET_MAX_CLIENTS 1 // Max number of concurrent telnet clients
|
|
#endif
|
|
|
|
#ifndef TELNET_SERVER
|
|
#define TELNET_SERVER TELNET_SERVER_ASYNC // Can be either TELNET_SERVER_ASYNC (using ESPAsyncTCP) or TELNET_SERVER_WIFISERVER (using WiFiServer)
|
|
#endif
|
|
|
|
#ifndef TELNET_SERVER_ASYNC_BUFFERED
|
|
#define TELNET_SERVER_ASYNC_BUFFERED 1 // Enable buffered output for telnet server (+1Kb)
|
|
// Helps to avoid lost data with lwip2 TCP_MSS=536 option
|
|
#endif
|
|
|
|
// Enable this flag to add support for reverse telnet (+800 bytes)
|
|
// This is useful to telnet to a device behind a NAT or firewall
|
|
// To use this feature, start a listen server on a publicly reachable host with e.g. "ncat -vlp <port>" and use the MQTT reverse telnet command to connect
|
|
#ifndef TELNET_REVERSE_SUPPORT
|
|
#define TELNET_REVERSE_SUPPORT 0
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// TERMINAL
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef TERMINAL_SUPPORT
|
|
#define TERMINAL_SUPPORT 1 // Enable terminal commands (0.97Kb)
|
|
#endif
|
|
|
|
#ifndef TERMINAL_SHARED_BUFFER_SIZE
|
|
#define TERMINAL_SHARED_BUFFER_SIZE 128 // Maximum size for command line, shared by the WebUI, Telnet and Serial
|
|
#endif
|
|
|
|
#ifndef TERMINAL_MQTT_SUPPORT
|
|
#define TERMINAL_MQTT_SUPPORT 0 // MQTT Terminal support built in
|
|
// Depends on MQTT_SUPPORT and TERMINAL_SUPPORT commands being available
|
|
#endif
|
|
|
|
#ifndef TERMINAL_WEB_API_SUPPORT
|
|
#define TERMINAL_WEB_API_SUPPORT 0 // Web server API Terminal support built in
|
|
// Depends on WEB_SUPPORT and TERMINAL_SUPPORT commands being available
|
|
#endif
|
|
|
|
#ifndef TERMINAL_WEB_API_PATH
|
|
#define TERMINAL_WEB_API_PATH "cmd"
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// SYSTEM CHECK
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef SYSTEM_CHECK_ENABLED
|
|
#define SYSTEM_CHECK_ENABLED 1 // Enable crash check by default
|
|
#endif
|
|
|
|
#ifndef SYSTEM_CHECK_TIME
|
|
#define SYSTEM_CHECK_TIME 60000 // The system is considered stable after these many millis
|
|
#endif
|
|
|
|
#ifndef SYSTEM_CHECK_MAX
|
|
#define SYSTEM_CHECK_MAX 5 // After this many crashes on boot
|
|
// the system is flagged as unstable
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// EEPROM
|
|
//------------------------------------------------------------------------------
|
|
|
|
//#define EEPROM_RORATE_SECTORS 2 // Number of sectors to use for EEPROM rotation
|
|
// If not defined the firmware will use a number based
|
|
// on the number of available sectors
|
|
|
|
#ifndef SAVE_CRASH_ENABLED
|
|
#define SAVE_CRASH_ENABLED 1 // Save stack trace to EEPROM by default
|
|
// Depends on DEBUG_SUPPORT == 1
|
|
#endif
|
|
|
|
#ifndef SAVE_CRASH_STACK_TRACE_MAX
|
|
#define SAVE_CRASH_STACK_TRACE_MAX 0x80 // limit at 128 bytes (increment/decrement by 16)
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// GARLAND
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef GARLAND_SUPPORT
|
|
#define GARLAND_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef GARLAND_D_PIN
|
|
#define GARLAND_D_PIN 4 // WS2812 pin number (default: D2 / GPIO4)
|
|
#endif
|
|
|
|
#ifndef GARLAND_LEDS
|
|
#define GARLAND_LEDS 60 // Number of LEDs
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// THERMOSTAT
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef THERMOSTAT_SUPPORT
|
|
#define THERMOSTAT_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef THERMOSTAT_DISPLAY_SUPPORT
|
|
#define THERMOSTAT_DISPLAY_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef THERMOSTAT_DISPLAY_OFF_INTERVAL // Interval in seconds after which display will be switched off
|
|
#define THERMOSTAT_DISPLAY_OFF_INTERVAL 0 // This will prevent it from burnout
|
|
#endif // 0 - newer switch display off
|
|
|
|
#define THERMOSTAT_SERVER_LOST_INTERVAL 120000 //server means lost after 2 min from last response
|
|
#define THERMOSTAT_REMOTE_TEMP_MAX_WAIT 120 // 2 min
|
|
|
|
#ifndef THERMOSTAT_REMOTE_SENSOR_NAME
|
|
#define THERMOSTAT_REMOTE_SENSOR_NAME "" // Get remote temp(hum) from mqtt topic of this device
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// HEARTBEAT REPORT
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef HEARTBEAT_REPORT_STATUS
|
|
#define HEARTBEAT_REPORT_STATUS 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_SSID
|
|
#define HEARTBEAT_REPORT_SSID 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_IP
|
|
#define HEARTBEAT_REPORT_IP 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_MAC
|
|
#define HEARTBEAT_REPORT_MAC 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_RSSI
|
|
#define HEARTBEAT_REPORT_RSSI 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_UPTIME
|
|
#define HEARTBEAT_REPORT_UPTIME 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_DATETIME
|
|
#define HEARTBEAT_REPORT_DATETIME 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_FREEHEAP
|
|
#define HEARTBEAT_REPORT_FREEHEAP 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_VCC
|
|
#define HEARTBEAT_REPORT_VCC 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_RELAY
|
|
#define HEARTBEAT_REPORT_RELAY 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_LIGHT
|
|
#define HEARTBEAT_REPORT_LIGHT 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_HOSTNAME
|
|
#define HEARTBEAT_REPORT_HOSTNAME 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_DESCRIPTION
|
|
#define HEARTBEAT_REPORT_DESCRIPTION 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_APP
|
|
#define HEARTBEAT_REPORT_APP 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_VERSION
|
|
#define HEARTBEAT_REPORT_VERSION 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_BOARD
|
|
#define HEARTBEAT_REPORT_BOARD 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_LOADAVG
|
|
#define HEARTBEAT_REPORT_LOADAVG 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_INTERVAL
|
|
#define HEARTBEAT_REPORT_INTERVAL 0
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_RANGE
|
|
#define HEARTBEAT_REPORT_RANGE 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_REMOTE_TEMP
|
|
#define HEARTBEAT_REPORT_REMOTE_TEMP 1
|
|
#endif
|
|
|
|
#ifndef HEARTBEAT_REPORT_BSSID
|
|
#define HEARTBEAT_REPORT_BSSID 0
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// Load average
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef LOADAVG_INTERVAL
|
|
#define LOADAVG_INTERVAL 30000 // Interval between calculating load average (in ms)
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// RELAY
|
|
//------------------------------------------------------------------------------
|
|
|
|
// Enable general support for relays (aka switches)
|
|
#ifndef RELAY_SUPPORT
|
|
#define RELAY_SUPPORT 1
|
|
#endif
|
|
|
|
// ESP01-relays with STM co-MCU driving the relays
|
|
#ifndef RELAY_PROVIDER_STM_SUPPORT
|
|
#define RELAY_PROVIDER_STM_SUPPORT 0
|
|
#endif
|
|
|
|
// Sonoff Dual, using serial protocol
|
|
#ifndef RELAY_PROVIDER_DUAL_SUPPORT
|
|
#define RELAY_PROVIDER_DUAL_SUPPORT 0
|
|
#endif
|
|
|
|
// Default boot mode: 0 means OFF, 1 ON and 2 whatever was before
|
|
#ifndef RELAY_BOOT_MODE
|
|
#define RELAY_BOOT_MODE RELAY_BOOT_OFF
|
|
#endif
|
|
|
|
// One of RELAY_SYNC_ANY, RELAY_SYNC_NONE_OR_ONE, RELAY_SYNC_SAME or RELAY_SYNC_FIRST
|
|
// Default to ANY i.e. don't do anything
|
|
#ifndef RELAY_SYNC
|
|
#define RELAY_SYNC RELAY_SYNC_ANY
|
|
#endif
|
|
|
|
// 0 (ms) means EVERY relay switches as soon as possible
|
|
// otherwise, wait up until this much time before changing the status
|
|
#ifndef RELAY_DELAY_INTERLOCK
|
|
#define RELAY_DELAY_INTERLOCK 0
|
|
#endif
|
|
|
|
// Default pulse mode / normal mode. Switching from it will start the 'pulse' timer and reset the relay back after it finishes
|
|
#ifndef RELAY_PULSE_MODE
|
|
#define RELAY_PULSE_MODE RELAY_PULSE_NONE
|
|
#endif
|
|
|
|
// Default pulse time in seconds
|
|
#ifndef RELAY_PULSE_TIME
|
|
#define RELAY_PULSE_TIME 0.0
|
|
#endif
|
|
|
|
// Relay requests flood protection window - in seconds
|
|
#ifndef RELAY_FLOOD_WINDOW
|
|
#define RELAY_FLOOD_WINDOW 3.0
|
|
#endif
|
|
|
|
// Allowed actual relay changes inside requests flood protection window
|
|
#ifndef RELAY_FLOOD_CHANGES
|
|
#define RELAY_FLOOD_CHANGES 5
|
|
#endif
|
|
|
|
// Pulse with in milliseconds for a latched relay
|
|
#ifndef RELAY_LATCHING_PULSE
|
|
#define RELAY_LATCHING_PULSE 10
|
|
#endif
|
|
|
|
// Do not save relay state after these many milliseconds
|
|
#ifndef RELAY_SAVE_DELAY
|
|
#define RELAY_SAVE_DELAY 1000
|
|
#endif
|
|
|
|
// Configure the MQTT payload for ON, OFF and TOGGLE
|
|
#ifndef RELAY_MQTT_OFF
|
|
#define RELAY_MQTT_OFF "0"
|
|
#endif
|
|
|
|
#ifndef RELAY_MQTT_ON
|
|
#define RELAY_MQTT_ON "1"
|
|
#endif
|
|
|
|
#ifndef RELAY_MQTT_TOGGLE
|
|
#define RELAY_MQTT_TOGGLE "2"
|
|
#endif
|
|
|
|
#ifndef RELAY_MQTT_TOPIC_MODE
|
|
#define RELAY_MQTT_TOPIC_MODE RELAY_MQTT_TOPIC_NORMAL
|
|
#endif
|
|
|
|
#ifndef RELAY_MQTT_DISCONNECT_STATUS
|
|
#define RELAY_MQTT_DISCONNECT_STATUS RELAY_MQTT_DISCONNECT_NONE
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// BUTTON
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef BUTTON_SUPPORT
|
|
#define BUTTON_SUPPORT 1
|
|
#endif
|
|
|
|
#ifndef BUTTON_DEBOUNCE_DELAY
|
|
#define BUTTON_DEBOUNCE_DELAY 50 // Debounce delay (ms)
|
|
#endif
|
|
|
|
#ifndef BUTTON_REPEAT_DELAY
|
|
#define BUTTON_REPEAT_DELAY 500 // Time in ms to wait for a second (or third...) click
|
|
#endif
|
|
|
|
#ifndef BUTTON_LNGCLICK_DELAY
|
|
#define BUTTON_LNGCLICK_DELAY 1000 // Time in ms holding the button down to get a long click
|
|
#endif
|
|
|
|
#ifndef BUTTON_LNGLNGCLICK_DELAY
|
|
#define BUTTON_LNGLNGCLICK_DELAY 10000 // Time in ms holding the button down to get a long-long click
|
|
#endif
|
|
|
|
#ifndef BUTTON_MQTT_SEND_ALL_EVENTS
|
|
#define BUTTON_MQTT_SEND_ALL_EVENTS 0 // 0 - to send only events the are bound to actions
|
|
// 1 - to send all button events to MQTT
|
|
#endif
|
|
|
|
#ifndef BUTTON_MQTT_RETAIN
|
|
#define BUTTON_MQTT_RETAIN 0
|
|
#endif
|
|
|
|
// Generic digital pin support
|
|
|
|
#ifndef BUTTON_PROVIDER_GPIO_SUPPORT
|
|
#define BUTTON_PROVIDER_GPIO_SUPPORT 1
|
|
#endif
|
|
|
|
// Resistor ladder support. Poll analog pin and return digital LOW when analog reading is in a certain range
|
|
// ref. https://github.com/bxparks/AceButton/tree/develop/docs/resistor_ladder
|
|
// Uses BUTTON#_ANALOG_LEVEL for the individual button level configuration
|
|
|
|
#ifndef BUTTON_PROVIDER_ANALOG_SUPPORT
|
|
#define BUTTON_PROVIDER_ANALOG_SUPPORT 0
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// ENCODER
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef ENCODER_SUPPORT
|
|
#define ENCODER_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef ENCODER_MINIMUM_DELTA
|
|
#define ENCODER_MINIMUM_DELTA 1
|
|
#endif
|
|
|
|
//------------------------------------------------------------------------------
|
|
// LED
|
|
//------------------------------------------------------------------------------
|
|
|
|
#ifndef LED_SUPPORT
|
|
#define LED_SUPPORT 1
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// WIFI
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef WIFI_CONNECT_RETRIES
|
|
#define WIFI_CONNECT_RETRIES 3 // Number of times before changing to the next configured network
|
|
#endif
|
|
|
|
#ifndef WIFI_CONNECT_INTERVAL
|
|
#define WIFI_CONNECT_INTERVAL 3000 // Time (ms) between connection attempts
|
|
#endif
|
|
|
|
#ifndef WIFI_RECONNECT_INTERVAL
|
|
#define WIFI_RECONNECT_INTERVAL 120000 // When all retries on all networks are exhausted, wait for this time (ms) and start from the beginning
|
|
#endif
|
|
|
|
#ifndef WIFI_MAX_NETWORKS
|
|
#define WIFI_MAX_NETWORKS 5 // Maximum number of WiFi configurations in settings
|
|
#endif
|
|
|
|
#ifndef WIFI_AP_CAPTIVE_SUPPORT
|
|
#define WIFI_AP_CAPTIVE_SUPPORT 1 // Captive portal for AP mode
|
|
#endif
|
|
|
|
#ifndef WIFI_AP_CAPTIVE_ENABLED
|
|
#define WIFI_AP_CAPTIVE_ENABLED 1 // Enabled by default
|
|
#endif
|
|
|
|
#ifndef WIFI_STA_MODE
|
|
#define WIFI_STA_MODE wifi::StaMode::Enabled // By default, turn on STA interface and try to connect to configured networks
|
|
// - wifi::StaMode::Enabled (default)
|
|
// - wifi::StaMode::Disabled keeps STA disabled
|
|
#endif
|
|
|
|
#ifndef WIFI_AP_MODE
|
|
#define WIFI_AP_MODE wifi::ApMode::Fallback // By default, enable AP if there is no STA connection
|
|
// - wifi::ApMode::Fallback (default)
|
|
// - wifi::ApMode::Enabled keeps AP enabled independent of STA
|
|
// - wifi::ApMode::Disabled keeps AP disabled
|
|
#endif
|
|
|
|
#ifndef WIFI_FALLBACK_TIMEOUT
|
|
#define WIFI_FALLBACK_TIMEOUT 60000 // When AP is in FALLBACK mode and STA is connected,
|
|
// how long to wait until stopping the AP
|
|
#endif
|
|
|
|
#ifndef WIFI_AP_SSID
|
|
#define WIFI_AP_SSID "" // (optional) Specify softAp SSID.
|
|
// By default or when empty, hostname (or device identifier) is used instead.
|
|
#endif
|
|
|
|
#ifndef WIFI_AP_PASS
|
|
#define WIFI_AP_PASS "" // (optional) Specify softAp passphrase
|
|
// By default or when empty, admin password is used instead.
|
|
#endif
|
|
|
|
#ifndef WIFI_AP_LEASES_SUPPORT
|
|
#define WIFI_AP_LEASES_SUPPORT 0 // (optional) Specify softAp MAC<->IP DHCP reservations
|
|
// Use `set wifiApLease# MAC`, where MAC is a valid 12-byte HEX number without colons
|
|
#endif
|
|
|
|
#ifndef WIFI_AP_CHANNEL
|
|
#define WIFI_AP_CHANNEL 1
|
|
#endif
|
|
|
|
#ifndef WIFI_SLEEP_MODE
|
|
#define WIFI_SLEEP_MODE WIFI_NONE_SLEEP // WIFI_NONE_SLEEP, WIFI_LIGHT_SLEEP or WIFI_MODEM_SLEEP
|
|
#endif
|
|
|
|
#ifndef WIFI_SCAN_NETWORKS
|
|
#define WIFI_SCAN_NETWORKS 1 // Perform a network scan before connecting and when RSSI threshold is reached
|
|
#endif
|
|
|
|
#ifndef WIFI_SCAN_RSSI_THRESHOLD
|
|
#define WIFI_SCAN_RSSI_THRESHOLD -73 // Consider current network for a reconnection cycle
|
|
// when it's RSSI value is below the specified threshold
|
|
#endif
|
|
|
|
#ifndef WIFI_SCAN_RSSI_CHECKS
|
|
#define WIFI_SCAN_RSSI_CHECKS 3 // Amount of RSSI threshold checks before starting a scan
|
|
#endif
|
|
|
|
#ifndef WIFI_SCAN_RSSI_CHECK_INTERVAL
|
|
#define WIFI_SCAN_RSSI_CHECK_INTERVAL 60000 // Time (ms) between RSSI checks
|
|
#endif
|
|
|
|
// Optional hardcoded configuration
|
|
// NOTICE that these values become factory-defaults
|
|
|
|
#ifndef WIFI1_SSID
|
|
#define WIFI1_SSID ""
|
|
#endif
|
|
|
|
#ifndef WIFI1_PASS
|
|
#define WIFI1_PASS ""
|
|
#endif
|
|
|
|
#ifndef WIFI1_IP
|
|
#define WIFI1_IP ""
|
|
#endif
|
|
|
|
#ifndef WIFI1_GW
|
|
#define WIFI1_GW ""
|
|
#endif
|
|
|
|
#ifndef WIFI1_MASK
|
|
#define WIFI1_MASK ""
|
|
#endif
|
|
|
|
#ifndef WIFI1_DNS
|
|
#define WIFI1_DNS ""
|
|
#endif
|
|
|
|
#ifndef WIFI2_SSID
|
|
#define WIFI2_SSID ""
|
|
#endif
|
|
|
|
#ifndef WIFI2_PASS
|
|
#define WIFI2_PASS ""
|
|
#endif
|
|
|
|
#ifndef WIFI2_IP
|
|
#define WIFI2_IP ""
|
|
#endif
|
|
|
|
#ifndef WIFI2_GW
|
|
#define WIFI2_GW ""
|
|
#endif
|
|
|
|
#ifndef WIFI2_MASK
|
|
#define WIFI2_MASK ""
|
|
#endif
|
|
|
|
#ifndef WIFI2_DNS
|
|
#define WIFI2_DNS ""
|
|
#endif
|
|
|
|
#ifndef WIFI3_SSID
|
|
#define WIFI3_SSID ""
|
|
#endif
|
|
|
|
#ifndef WIFI3_PASS
|
|
#define WIFI3_PASS ""
|
|
#endif
|
|
|
|
#ifndef WIFI3_IP
|
|
#define WIFI3_IP ""
|
|
#endif
|
|
|
|
#ifndef WIFI3_GW
|
|
#define WIFI3_GW ""
|
|
#endif
|
|
|
|
#ifndef WIFI3_MASK
|
|
#define WIFI3_MASK ""
|
|
#endif
|
|
|
|
#ifndef WIFI3_DNS
|
|
#define WIFI3_DNS ""
|
|
#endif
|
|
|
|
#ifndef WIFI4_SSID
|
|
#define WIFI4_SSID ""
|
|
#endif
|
|
|
|
#ifndef WIFI4_PASS
|
|
#define WIFI4_PASS ""
|
|
#endif
|
|
|
|
#ifndef WIFI4_IP
|
|
#define WIFI4_IP ""
|
|
#endif
|
|
|
|
#ifndef WIFI4_GW
|
|
#define WIFI4_GW ""
|
|
#endif
|
|
|
|
#ifndef WIFI4_MASK
|
|
#define WIFI4_MASK ""
|
|
#endif
|
|
|
|
#ifndef WIFI4_DNS
|
|
#define WIFI4_DNS ""
|
|
#endif
|
|
|
|
#ifndef WIFI5_SSID
|
|
#define WIFI5_SSID ""
|
|
#endif
|
|
|
|
#ifndef WIFI5_PASS
|
|
#define WIFI5_PASS ""
|
|
#endif
|
|
|
|
#ifndef WIFI5_IP
|
|
#define WIFI5_IP ""
|
|
#endif
|
|
|
|
#ifndef WIFI5_GW
|
|
#define WIFI5_GW ""
|
|
#endif
|
|
|
|
#ifndef WIFI5_MASK
|
|
#define WIFI5_MASK ""
|
|
#endif
|
|
|
|
#ifndef WIFI5_DNS
|
|
#define WIFI5_DNS ""
|
|
#endif
|
|
|
|
// ref: https://docs.espressif.com/projects/esp-idf/en/latest/api-reference/kconfig.html#config-lwip-esp-gratuitous-arp
|
|
// ref: https://github.com/xoseperez/espurna/pull/1877#issuecomment-525612546
|
|
//
|
|
// Broadcast gratuitous ARP periodically to update ARP tables on the AP and all devices on the same network.
|
|
// Helps to solve compatibility issues when ESP fails to timely reply to ARP requests, causing the device's ARP table entry to expire.
|
|
|
|
#ifndef WIFI_GRATUITOUS_ARP_SUPPORT
|
|
#define WIFI_GRATUITOUS_ARP_SUPPORT 1
|
|
#endif
|
|
|
|
// Interval is randomized on each boot in range from ..._MIN to ..._MAX (ms)
|
|
#ifndef WIFI_GRATUITOUS_ARP_INTERVAL_MIN
|
|
#define WIFI_GRATUITOUS_ARP_INTERVAL_MIN 15000
|
|
#endif
|
|
|
|
#ifndef WIFI_GRATUITOUS_ARP_INTERVAL_MAX
|
|
#define WIFI_GRATUITOUS_ARP_INTERVAL_MAX 30000
|
|
#endif
|
|
|
|
// ref: https://github.com/esp8266/Arduino/issues/6471
|
|
// ref: https://github.com/esp8266/Arduino/issues/6366
|
|
//
|
|
// Issue #6366 turned out to be high tx power causing weird behavior. Lowering tx power achieved stability.
|
|
#ifndef WIFI_OUTPUT_POWER_DBM
|
|
#define WIFI_OUTPUT_POWER_DBM 20.0f
|
|
#endif
|
|
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// WEB
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef WEB_SUPPORT
|
|
#define WEB_SUPPORT 1 // Enable web support (http, api, 121.65Kb)
|
|
#endif
|
|
|
|
#ifndef WEB_EMBEDDED
|
|
#define WEB_EMBEDDED 1 // Build the firmware with the web interface embedded in
|
|
#endif
|
|
|
|
#ifndef WEB_ACCESS_LOG
|
|
#define WEB_ACCESS_LOG 0 // Log every request that was received by the server (but, not necessarily processed)
|
|
#endif
|
|
|
|
// Requires ESPAsyncTCP to be built with ASYNC_TCP_SSL_ENABLED=1 and Arduino Core version >= 2.4.0
|
|
// XXX: This is not working at the moment!! Pending https://github.com/me-no-dev/ESPAsyncTCP/issues/95
|
|
#ifndef WEB_SSL_ENABLED
|
|
#define WEB_SSL_ENABLED 0 // Use HTTPS web interface
|
|
#endif
|
|
|
|
#ifndef WEB_USERNAME
|
|
#define WEB_USERNAME "admin" // HTTP username
|
|
#endif
|
|
|
|
#ifndef WEB_FORCE_PASS_CHANGE
|
|
#define WEB_FORCE_PASS_CHANGE 1 // Force the user to change the password if default one
|
|
#endif
|
|
|
|
#ifndef WEB_PORT
|
|
#define WEB_PORT 80 // HTTP port
|
|
#endif
|
|
|
|
// Defining a WEB_REMOTE_DOMAIN will enable Cross-Origin Resource Sharing (CORS)
|
|
// so you will be able to login to this device from another domain. This will allow
|
|
// you to manage all ESPurna devices in your local network from a unique installation
|
|
// of the web UI. This installation could be in a local server (a Raspberry Pi, for instance)
|
|
// or in the Internet. Since the WebUI is just one compressed file with HTML, CSS and JS
|
|
// there are no special requirements. Any static web server will do (NGinx, Apache, Lighttpd,...).
|
|
// The only requirement is that the resource must be available under this domain.
|
|
#ifndef WEB_REMOTE_DOMAIN
|
|
#define WEB_REMOTE_DOMAIN "http://espurna.io"
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// WEBSOCKETS
|
|
// -----------------------------------------------------------------------------
|
|
|
|
// This will only be enabled if WEB_SUPPORT is 1 (this is the default value)
|
|
#ifndef WS_AUTHENTICATION
|
|
#define WS_AUTHENTICATION 1 // WS authentication ON by default (see #507)
|
|
#endif
|
|
|
|
#ifndef WS_MAX_CLIENTS
|
|
#define WS_MAX_CLIENTS 5 // Max number of websocket connections
|
|
#endif
|
|
|
|
#ifndef WS_TIMEOUT
|
|
#define WS_TIMEOUT 1800000 // Timeout for secured websocket
|
|
#endif
|
|
|
|
#ifndef WS_UPDATE_INTERVAL
|
|
#define WS_UPDATE_INTERVAL 30000 // Update clients every 30 seconds
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// API
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef API_SUPPORT
|
|
#define API_SUPPORT 1 // API (REST & RPC) support built in
|
|
#endif
|
|
|
|
// This will only be enabled if WEB_SUPPORT is 1 (this is the default value)
|
|
#ifndef API_ENABLED
|
|
#define API_ENABLED 0 // Do not enable API by default
|
|
#endif
|
|
|
|
#ifndef API_KEY
|
|
#define API_KEY "" // Do not enable API by default. WebUI will automatically generate the key
|
|
#endif
|
|
|
|
#ifndef API_RESTFUL
|
|
#define API_RESTFUL 1 // A restful API requires changes to be issued as PUT requests
|
|
// Setting this to 0 will allow using GET to change relays, for instance
|
|
#endif
|
|
|
|
#ifndef API_JSON_BUFFER_SIZE
|
|
#define API_JSON_BUFFER_SIZE 256 // Size of the (de)serializer buffer.
|
|
#endif
|
|
|
|
#ifndef API_BASE_PATH
|
|
#define API_BASE_PATH "/api/"
|
|
#endif
|
|
|
|
#ifndef API_REAL_TIME_VALUES
|
|
#define API_REAL_TIME_VALUES 0 // Show filtered/median values by default (0 => median, 1 => real time)
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// MDNS / LLMNR / NETBIOS / SSDP
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef MDNS_SERVER_SUPPORT
|
|
#define MDNS_SERVER_SUPPORT 1 // Publish services using mDNS by default (1.48Kb)
|
|
#endif
|
|
|
|
#ifndef LLMNR_SUPPORT
|
|
#define LLMNR_SUPPORT 0 // Publish device using LLMNR protocol by default (1.95Kb) - requires Core version >= 2.4.0
|
|
#endif
|
|
|
|
#ifndef NETBIOS_SUPPORT
|
|
#define NETBIOS_SUPPORT 0 // Publish device using NetBIOS protocol by default (1.26Kb) - requires Core version >= 2.4.0
|
|
#endif
|
|
|
|
#ifndef SSDP_SUPPORT
|
|
#define SSDP_SUPPORT 0 // Publish device using SSDP protocol by default (4.59Kb)
|
|
// Not compatible with ALEXA_SUPPORT at the moment
|
|
#endif
|
|
|
|
#ifndef SSDP_DEVICE_TYPE
|
|
#define SSDP_DEVICE_TYPE "upnp:rootdevice"
|
|
//#define SSDP_DEVICE_TYPE "urn:schemas-upnp-org:device:BinaryLight:1"
|
|
#endif
|
|
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// SPIFFS
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef SPIFFS_SUPPORT
|
|
#define SPIFFS_SUPPORT 0 // Do not add support for SPIFFS by default
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// SSL Client ** EXPERIMENTAL **
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef SECURE_CLIENT
|
|
#define SECURE_CLIENT SECURE_CLIENT_NONE // What variant of WiFiClient to use
|
|
// SECURE_CLIENT_NONE - No secure client support (default)
|
|
// SECURE_CLIENT_AXTLS - axTLS client secure support (All Core versions, ONLY TLS 1.1)
|
|
// SECURE_CLIENT_BEARSSL - BearSSL client secure support (starting with 2.5.0, TLS 1.2)
|
|
//
|
|
// axTLS marked for derecation since Arduino Core 2.4.2 and **will** be removed in the future
|
|
#endif
|
|
|
|
// Security check that is performed when the connection is established:
|
|
// SECURE_CLIENT_CHECK_CA - Use Trust Anchor / Root Certificate
|
|
// Supported only by the SECURE_CLIENT_BEARSSL
|
|
// (See respective ..._SECURE_CLIENT_INCLUDE_CA options per-module)
|
|
// SECURE_CLIENT_CHECK_FINGERPRINT - Check certificate fingerprint
|
|
// SECURE_CLIENT_CHECK_NONE - Allow insecure connections
|
|
|
|
#ifndef SECURE_CLIENT_CHECK
|
|
|
|
#if SECURE_CLIENT == SECURE_CLIENT_BEARSSL
|
|
#define SECURE_CLIENT_CHECK SECURE_CLIENT_CHECK_CA
|
|
|
|
#else
|
|
#define SECURE_CLIENT_CHECK SECURE_CLIENT_CHECK_FINGERPRINT
|
|
|
|
#endif
|
|
|
|
|
|
#endif // SECURE_CLIENT_CHECK
|
|
|
|
// Support Maximum Fragment Length Negotiation TLS extension
|
|
// "...negotiate a smaller maximum fragment length due to memory limitations or bandwidth limitations."
|
|
// - https://arduino-esp8266.readthedocs.io/en/latest/esp8266wifi/bearssl-client-secure-class.html#mfln-or-maximum-fragment-length-negotiation-saving-ram
|
|
// - https://tools.ietf.org/html/rfc6066#section-4
|
|
#ifndef SECURE_CLIENT_MFLN
|
|
#define SECURE_CLIENT_MFLN 0 // The only possible values are: 512, 1024, 2048 and 4096
|
|
// Set to 0 to disable (default)
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// OTA
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef OTA_PORT
|
|
#define OTA_PORT 8266 // Port for ArduinoOTA
|
|
#endif
|
|
|
|
#ifndef OTA_MQTT_SUPPORT
|
|
#define OTA_MQTT_SUPPORT 0 // Listen for HTTP(s) URLs at '<root topic>/ota'. Depends on OTA_CLIENT
|
|
#endif
|
|
|
|
#ifndef OTA_ARDUINOOTA_SUPPORT
|
|
#define OTA_ARDUINOOTA_SUPPORT 1 // Support ArduinoOTA by default (4.2Kb)
|
|
// Implicitly depends on ESP8266mDNS library, thus increasing firmware size
|
|
#endif
|
|
|
|
#ifndef OTA_CLIENT
|
|
#define OTA_CLIENT OTA_CLIENT_ASYNCTCP // Terminal / MQTT OTA support
|
|
// OTA_CLIENT_ASYNCTCP (ESPAsyncTCP library)
|
|
// OTA_CLIENT_HTTPUPDATE (Arduino Core library)j
|
|
// OTA_CLIENT_NONE to disable
|
|
#endif
|
|
|
|
#ifndef OTA_WEB_SUPPORT
|
|
#define OTA_WEB_SUPPORT 1 // Support `/upgrade` endpoint and WebUI OTA handler
|
|
#endif
|
|
|
|
#define OTA_GITHUB_FP "CA:06:F5:6B:25:8B:7A:0D:4F:2B:05:47:09:39:47:86:51:15:19:84"
|
|
|
|
#ifndef OTA_FINGERPRINT
|
|
#define OTA_FINGERPRINT OTA_GITHUB_FP
|
|
#endif
|
|
|
|
#ifndef OTA_SECURE_CLIENT_CHECK
|
|
#define OTA_SECURE_CLIENT_CHECK SECURE_CLIENT_CHECK
|
|
#endif
|
|
|
|
#ifndef OTA_SECURE_CLIENT_MFLN
|
|
#define OTA_SECURE_CLIENT_MFLN SECURE_CLIENT_MFLN
|
|
#endif
|
|
|
|
#ifndef OTA_SECURE_CLIENT_INCLUDE_CA
|
|
#define OTA_SECURE_CLIENT_INCLUDE_CA 0 // Use user-provided CA. Only PROGMEM PEM option is supported.
|
|
// TODO: eventually should be replaced with pre-parsed structs, read directly from flash
|
|
// (ref: https://github.com/earlephilhower/bearssl-esp8266/pull/14)
|
|
//
|
|
// When enabled, current implementation includes "static/ota_client_trusted_root_ca.h" with
|
|
// const char _ota_client_trusted_root_ca[] PROGMEM = "...PEM data...";
|
|
// By default, using DigiCert root in "static/digicert_evroot_pem.h" (for https://github.com)
|
|
#endif
|
|
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// NOFUSS
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef NOFUSS_SUPPORT
|
|
#define NOFUSS_SUPPORT 0 // Do not enable support for NoFuss by default (12.65Kb)
|
|
#endif
|
|
|
|
#ifndef NOFUSS_ENABLED
|
|
#define NOFUSS_ENABLED 0 // Do not perform NoFUSS updates by default
|
|
#endif
|
|
|
|
#ifndef NOFUSS_SERVER
|
|
#define NOFUSS_SERVER "" // Default NoFuss Server
|
|
#endif
|
|
|
|
#ifndef NOFUSS_INTERVAL
|
|
#define NOFUSS_INTERVAL 3600000 // Check for updates every hour
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// UART <-> MQTT
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef UART_MQTT_SUPPORT
|
|
#define UART_MQTT_SUPPORT 0 // No support by default
|
|
#endif
|
|
|
|
#ifndef UART_MQTT_USE_SOFT
|
|
#define UART_MQTT_USE_SOFT 0 // Use SoftwareSerial
|
|
#endif
|
|
|
|
#ifndef UART_MQTT_HW_PORT
|
|
#define UART_MQTT_HW_PORT Serial // Hardware serial port (if UART_MQTT_USE_SOFT == 0)
|
|
#endif
|
|
|
|
#ifndef UART_MQTT_RX_PIN
|
|
#define UART_MQTT_RX_PIN 4 // RX PIN (if UART_MQTT_USE_SOFT == 1)
|
|
#endif
|
|
|
|
#ifndef UART_MQTT_TX_PIN
|
|
#define UART_MQTT_TX_PIN 5 // TX PIN (if UART_MQTT_USE_SOFT == 1)
|
|
#endif
|
|
|
|
#ifndef UART_MQTT_BAUDRATE
|
|
#define UART_MQTT_BAUDRATE 115200 // Serial speed
|
|
#endif
|
|
|
|
#ifndef UART_MQTT_TERMINATION
|
|
#define UART_MQTT_TERMINATION '\n' // Termination character
|
|
#endif
|
|
|
|
#define UART_MQTT_BUFFER_SIZE 100 // UART buffer size
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// MQTT
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef MQTT_SUPPORT
|
|
#define MQTT_SUPPORT 1 // MQTT support (22.38Kb async, 12.48Kb sync)
|
|
#endif
|
|
|
|
|
|
#ifndef MQTT_LIBRARY
|
|
#define MQTT_LIBRARY MQTT_LIBRARY_ASYNCMQTTCLIENT // MQTT_LIBRARY_ASYNCMQTTCLIENT (default, https://github.com/marvinroger/async-mqtt-client)
|
|
// MQTT_LIBRARY_PUBSUBCLIENT (https://github.com/knolleary/pubsubclient)
|
|
// MQTT_LIBRARY_ARDUINOMQTT (https://github.com/256dpi/arduino-mqtt)
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// MQTT OVER SSL
|
|
// -----------------------------------------------------------------------------
|
|
//
|
|
// Requires SECURE_CLIENT set to SECURE_CLIENT_AXTLS or SECURE_CLIENT_BEARSSL
|
|
// It is recommended to use MQTT_LIBRARY_ARDUINOMQTT or MQTT_LIBRARY_PUBSUBCLIENT
|
|
// It is recommended to use SECURE_CLIENT_BEARSSL
|
|
// It is recommended to use ESP8266 Arduino Core >= 2.5.2 with SECURE_CLIENT_BEARSSL
|
|
//
|
|
// Current version of MQTT_LIBRARY_ASYNCMQTTCLIENT only supports SECURE_CLIENT_AXTLS
|
|
//
|
|
// It is recommended to use WEB_SUPPORT=0 with either SECURE_CLIENT option, as there are miscellaneous problems when using them simultaneously
|
|
// (although, things might've improved, and I'd encourage to check whether this is true or not)
|
|
//
|
|
// When using MQTT_LIBRARY_PUBSUBCLIENT or MQTT_LIBRARY_ARDUINOMQTT, you will have to disable every module that uses ESPAsyncTCP:
|
|
// ALEXA_SUPPORT=0, INFLUXDB_SUPPORT=0, TELNET_SUPPORT=0, THINGSPEAK_SUPPORT=0, DEBUG_TELNET_SUPPORT=0 and WEB_SUPPORT=0
|
|
// Or, use "sync" versions instead (note that not every module has this option):
|
|
// THINGSPEAK_USE_ASYNC=0, TELNET_SERVER=TELNET_SERVER_WIFISERVER
|
|
//
|
|
// See SECURE_CLIENT_CHECK for all possible connection verification options.
|
|
//
|
|
// The simpliest way to verify SSL connection is to use fingerprinting.
|
|
// For example, to get Google's MQTT server certificate fingerprint, run the following command:
|
|
// $ echo -n | openssl s_client -connect mqtt.googleapis.com:8883 2>&1 | openssl x509 -noout -fingerprint -sha1 | cut -d\= -f2
|
|
// Note that fingerprint will change when certificate changes e.g. LetsEncrypt renewals or when the CSR updates
|
|
|
|
#ifndef MQTT_SSL_ENABLED
|
|
#define MQTT_SSL_ENABLED 0 // By default MQTT over SSL will not be enabled
|
|
#endif
|
|
|
|
#ifndef MQTT_SSL_FINGERPRINT
|
|
#define MQTT_SSL_FINGERPRINT "" // SSL fingerprint of the server
|
|
#endif
|
|
|
|
#ifndef MQTT_SECURE_CLIENT_CHECK
|
|
#define MQTT_SECURE_CLIENT_CHECK SECURE_CLIENT_CHECK // Use global verification setting by default
|
|
#endif
|
|
|
|
#ifndef MQTT_SECURE_CLIENT_MFLN
|
|
#define MQTT_SECURE_CLIENT_MFLN SECURE_CLIENT_MFLN // Use global MFLN setting by default
|
|
#endif
|
|
|
|
#ifndef MQTT_SECURE_CLIENT_INCLUDE_CA
|
|
#define MQTT_SECURE_CLIENT_INCLUDE_CA 0 // Use user-provided CA. Only PROGMEM PEM option is supported.
|
|
// When enabled, current implementation includes "static/mqtt_client_trusted_root_ca.h" with
|
|
// const char _mqtt_client_trusted_root_ca[] PROGMEM = "...PEM data...";
|
|
// By default, using LetsEncrypt X3 root in "static/letsencrypt_isrgroot_pem.h"
|
|
#endif
|
|
|
|
#ifndef MQTT_ENABLED
|
|
#define MQTT_ENABLED 0 // Do not enable MQTT connection by default
|
|
#endif
|
|
|
|
#ifndef MQTT_AUTOCONNECT
|
|
#define MQTT_AUTOCONNECT 1 // If enabled and MDNS_SERVER_SUPPORT=1 will perform an autodiscover and
|
|
// autoconnect to the first MQTT broker found if none defined
|
|
#endif
|
|
|
|
#ifndef MQTT_SERVER
|
|
#define MQTT_SERVER "" // Default MQTT broker address
|
|
#endif
|
|
|
|
#ifndef MQTT_USER
|
|
#define MQTT_USER "" // Default MQTT broker usename
|
|
#endif
|
|
|
|
#ifndef MQTT_PASS
|
|
#define MQTT_PASS "" // Default MQTT broker password
|
|
#endif
|
|
|
|
#ifndef MQTT_PORT
|
|
#define MQTT_PORT 1883 // MQTT broker port
|
|
#endif
|
|
|
|
#ifndef MQTT_TOPIC
|
|
#define MQTT_TOPIC "{hostname}" // Default MQTT base topic
|
|
#endif
|
|
|
|
#ifndef MQTT_RETAIN
|
|
#define MQTT_RETAIN true // MQTT retain flag
|
|
#endif
|
|
|
|
#ifndef MQTT_QOS
|
|
#define MQTT_QOS 0 // MQTT QoS value for all messages
|
|
#endif
|
|
|
|
#ifndef MQTT_KEEPALIVE
|
|
#define MQTT_KEEPALIVE 120 // MQTT keepalive value
|
|
#endif
|
|
|
|
#ifndef MQTT_RECONNECT_DELAY_MIN
|
|
#define MQTT_RECONNECT_DELAY_MIN 5000 // Try to reconnect in 5 seconds upon disconnection
|
|
#endif
|
|
|
|
#ifndef MQTT_RECONNECT_DELAY_STEP
|
|
#define MQTT_RECONNECT_DELAY_STEP 5000 // Increase the reconnect delay in 5 seconds after each failed attempt
|
|
#endif
|
|
|
|
#ifndef MQTT_RECONNECT_DELAY_MAX
|
|
#define MQTT_RECONNECT_DELAY_MAX 120000 // Set reconnect time to 2 minutes at most
|
|
#endif
|
|
|
|
|
|
#ifndef MQTT_SKIP_TIME
|
|
#define MQTT_SKIP_TIME 0 // Skip messages for N ms after connection. Disabled by default
|
|
#endif
|
|
|
|
#ifndef MQTT_USE_JSON
|
|
#define MQTT_USE_JSON 0 // Don't group messages in a JSON body by default
|
|
#endif
|
|
|
|
#ifndef MQTT_USE_JSON_DELAY
|
|
#define MQTT_USE_JSON_DELAY 100 // Wait this many ms before grouping messages
|
|
#endif
|
|
|
|
#ifndef MQTT_QUEUE_MAX_SIZE
|
|
#define MQTT_QUEUE_MAX_SIZE 20 // Size of the MQTT queue when MQTT_USE_JSON is enabled
|
|
#endif
|
|
|
|
#ifndef MQTT_BUFFER_MAX_SIZE
|
|
#define MQTT_BUFFER_MAX_SIZE 1024 // Size of the MQTT payload buffer for MQTT_MESSAGE_EVENT. Large messages will only be available via MQTT_MESSAGE_RAW_EVENT.
|
|
// Note: When using MQTT_LIBRARY_PUBSUBCLIENT, MQTT_MAX_PACKET_SIZE should not be more than this value.
|
|
#endif
|
|
|
|
// These are the properties that will be sent when useJson is true
|
|
#ifndef MQTT_ENQUEUE_IP
|
|
#define MQTT_ENQUEUE_IP 1
|
|
#endif
|
|
|
|
#ifndef MQTT_ENQUEUE_MAC
|
|
#define MQTT_ENQUEUE_MAC 1
|
|
#endif
|
|
|
|
#ifndef MQTT_ENQUEUE_HOSTNAME
|
|
#define MQTT_ENQUEUE_HOSTNAME 1
|
|
#endif
|
|
|
|
#ifndef MQTT_ENQUEUE_DATETIME
|
|
#define MQTT_ENQUEUE_DATETIME 1
|
|
#endif
|
|
|
|
#ifndef MQTT_ENQUEUE_MESSAGE_ID
|
|
#define MQTT_ENQUEUE_MESSAGE_ID 1
|
|
#endif
|
|
|
|
#ifndef MQTT_STATUS_ONLINE
|
|
#define MQTT_STATUS_ONLINE "1" // Value for the device ON message
|
|
#endif
|
|
|
|
#ifndef MQTT_STATUS_OFFLINE
|
|
#define MQTT_STATUS_OFFLINE "0" // Value for the device OFF message (will)
|
|
#endif
|
|
|
|
#define MQTT_ACTION_RESET "reboot" // RESET MQTT topic particle
|
|
|
|
// Custom get and set postfixes
|
|
// Use something like "/status" or "/set", with leading slash
|
|
// Since 1.9.0 the default value is "" for getter and "/set" for setter
|
|
#ifndef MQTT_GETTER
|
|
#define MQTT_GETTER ""
|
|
#endif
|
|
|
|
#ifndef MQTT_SETTER
|
|
#define MQTT_SETTER "/set"
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// BROKER
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef BROKER_SUPPORT
|
|
#define BROKER_SUPPORT 1 // The broker is a poor-man's pubsub manager
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// SETTINGS
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef SETTINGS_AUTOSAVE
|
|
#define SETTINGS_AUTOSAVE 1 // Autosave settings or force manual commit
|
|
#endif
|
|
|
|
#define SETTINGS_MAX_LIST_COUNT 16 // Maximum index for settings lists
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// LIGHT
|
|
// -----------------------------------------------------------------------------
|
|
|
|
// LIGHT_PROVIDER_DIMMER can have from 1 to 5 different channels.
|
|
// They have to be defined for each device in the hardware.h file.
|
|
// If 3 or more channels first 3 will be considered RGB.
|
|
// Usual configurations are:
|
|
// 1 channels => W
|
|
// 2 channels => WW
|
|
// 3 channels => RGB
|
|
// 4 channels => RGBW
|
|
// 5 channels => RGBWW
|
|
|
|
#ifndef LIGHT_PROVIDER
|
|
#define LIGHT_PROVIDER LIGHT_PROVIDER_NONE
|
|
#endif
|
|
|
|
#ifndef LIGHT_REPORT_DELAY
|
|
#define LIGHT_REPORT_DELAY 100 // Delay reporting current state for the specified number of ms after light update
|
|
#endif
|
|
|
|
#ifndef LIGHT_SAVE_ENABLED
|
|
#define LIGHT_SAVE_ENABLED 1 // Light channel values saved by default after each change
|
|
#endif
|
|
|
|
#ifndef LIGHT_SAVE_DELAY
|
|
#define LIGHT_SAVE_DELAY 5000 // Persist channel & brightness values after the specified number of ms
|
|
#endif
|
|
|
|
#ifndef LIGHT_MIN_PWM
|
|
#define LIGHT_MIN_PWM 0
|
|
#endif
|
|
|
|
#ifndef LIGHT_MAX_PWM
|
|
|
|
#if LIGHT_PROVIDER == LIGHT_PROVIDER_MY92XX
|
|
#define LIGHT_MAX_PWM 255
|
|
#elif LIGHT_PROVIDER == LIGHT_PROVIDER_DIMMER
|
|
#define LIGHT_MAX_PWM 10000 // 10000 * 200ns => 2 kHz
|
|
#else
|
|
#define LIGHT_MAX_PWM 0
|
|
#endif
|
|
|
|
#endif // LIGHT_MAX_PWM
|
|
|
|
#ifndef LIGHT_LIMIT_PWM
|
|
#define LIGHT_LIMIT_PWM LIGHT_MAX_PWM // Limit PWM to this value (prevent 100% power)
|
|
#endif
|
|
|
|
#ifndef LIGHT_MIN_VALUE
|
|
#define LIGHT_MIN_VALUE 0 // Minimum light value
|
|
#endif
|
|
|
|
#ifndef LIGHT_MAX_VALUE
|
|
#define LIGHT_MAX_VALUE 255 // Maximum light value
|
|
#endif
|
|
|
|
#ifndef LIGHT_MIN_BRIGHTNESS
|
|
#define LIGHT_MIN_BRIGHTNESS 0 // Minimum brightness value
|
|
#endif
|
|
|
|
#ifndef LIGHT_MAX_BRIGHTNESS
|
|
#define LIGHT_MAX_BRIGHTNESS 255 // Maximum brightness value
|
|
#endif
|
|
|
|
// Default mireds & kelvin to the Philips Hue limits
|
|
// https://developers.meethue.com/documentation/core-concepts
|
|
//
|
|
// Home Assistant also uses these, see Light::min_mireds, Light::max_mireds
|
|
// https://github.com/home-assistant/home-assistant/blob/dev/homeassistant/components/light/__init__.py
|
|
|
|
// Used when LIGHT_USE_WHITE AND LIGHT_USE_CCT is 1 - (1000000/Kelvin = MiReds)
|
|
// Warning! Don't change this yet, NOT FULLY IMPLEMENTED!
|
|
#ifndef LIGHT_COLDWHITE_MIRED
|
|
#define LIGHT_COLDWHITE_MIRED 153 // Coldwhite Strip, Value must be __BELOW__ W2!! (Default: 6535 Kelvin/153 MiRed)
|
|
#endif
|
|
|
|
#ifndef LIGHT_WARMWHITE_MIRED
|
|
#define LIGHT_WARMWHITE_MIRED 500 // Warmwhite Strip, Value must be __ABOVE__ W1!! (Default: 2000 Kelvin/500 MiRed)
|
|
#endif
|
|
|
|
#ifndef LIGHT_STEP
|
|
#define LIGHT_STEP 32 // Step size
|
|
#endif
|
|
|
|
#ifndef LIGHT_USE_COLOR
|
|
#define LIGHT_USE_COLOR 1 // Use 3 first channels as RGB
|
|
#endif
|
|
|
|
#ifndef LIGHT_USE_WHITE
|
|
#define LIGHT_USE_WHITE 0 // Use the 4th channel as (Warm-)White LEDs
|
|
#endif
|
|
|
|
#ifndef LIGHT_USE_CCT
|
|
#define LIGHT_USE_CCT 0 // Use the 5th channel as Coldwhite LEDs, LIGHT_USE_WHITE must be 1.
|
|
#endif
|
|
|
|
#ifndef LIGHT_USE_GAMMA
|
|
#define LIGHT_USE_GAMMA 0 // Use gamma correction for color channels
|
|
#endif
|
|
|
|
#ifndef LIGHT_USE_RGB
|
|
#define LIGHT_USE_RGB 0 // Use RGB color selector (1=> RGB, 0=> HSV)
|
|
#endif
|
|
|
|
#ifndef LIGHT_WHITE_FACTOR
|
|
#define LIGHT_WHITE_FACTOR 1 // When using LIGHT_USE_WHITE with uneven brightness LEDs,
|
|
// this factor is used to scale the white channel to match brightness
|
|
#endif
|
|
|
|
|
|
#ifndef LIGHT_USE_TRANSITIONS
|
|
#define LIGHT_USE_TRANSITIONS 1 // Transitions between colors
|
|
#endif
|
|
|
|
#ifndef LIGHT_TRANSITION_STEP
|
|
#define LIGHT_TRANSITION_STEP 10 // Time in millis between each transtion step
|
|
#endif
|
|
|
|
#ifndef LIGHT_TRANSITION_TIME
|
|
#define LIGHT_TRANSITION_TIME 500 // Time in millis from color to color
|
|
#endif
|
|
|
|
#ifndef LIGHT_RELAY_ENABLED
|
|
#define LIGHT_RELAY_ENABLED 1 // Add a virtual switch that controls the global light state. Depends on RELAY_SUPPORT
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// DOMOTICZ
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef DOMOTICZ_SUPPORT
|
|
#define DOMOTICZ_SUPPORT MQTT_SUPPORT // Build with domoticz (if MQTT) support (1.72Kb)
|
|
#endif
|
|
|
|
#ifndef DOMOTICZ_ENABLED
|
|
#define DOMOTICZ_ENABLED 0 // Disable domoticz by default
|
|
#endif
|
|
|
|
#ifndef DOMOTICZ_IN_TOPIC
|
|
#define DOMOTICZ_IN_TOPIC "domoticz/in" // Default subscription topic
|
|
#endif
|
|
|
|
#ifndef DOMOTICZ_OUT_TOPIC
|
|
#define DOMOTICZ_OUT_TOPIC "domoticz/out" // Default publication topic
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// HOME ASSISTANT
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef HOMEASSISTANT_SUPPORT
|
|
#define HOMEASSISTANT_SUPPORT MQTT_SUPPORT // Build with home assistant support (if MQTT, 1.64Kb)
|
|
#endif
|
|
|
|
#ifndef HOMEASSISTANT_ENABLED
|
|
#define HOMEASSISTANT_ENABLED 0 // Integration not enabled by default
|
|
#endif
|
|
|
|
#ifndef HOMEASSISTANT_PREFIX
|
|
#define HOMEASSISTANT_PREFIX "homeassistant" // Default MQTT prefix
|
|
#endif
|
|
|
|
#ifndef HOMEASSISTANT_RETAIN
|
|
#define HOMEASSISTANT_RETAIN MQTT_RETAIN // Make broker retain the messages
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// INFLUXDB
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef INFLUXDB_SUPPORT
|
|
#define INFLUXDB_SUPPORT 0 // Disable InfluxDB support by default (4.38Kb)
|
|
#endif
|
|
|
|
#ifndef INFLUXDB_ENABLED
|
|
#define INFLUXDB_ENABLED 0 // InfluxDB disabled by default
|
|
#endif
|
|
|
|
#ifndef INFLUXDB_HOST
|
|
#define INFLUXDB_HOST "" // Default server
|
|
#endif
|
|
|
|
#ifndef INFLUXDB_PORT
|
|
#define INFLUXDB_PORT 8086 // Default InfluxDB port
|
|
#endif
|
|
|
|
#ifndef INFLUXDB_DATABASE
|
|
#define INFLUXDB_DATABASE "" // Default database
|
|
#endif
|
|
|
|
#ifndef INFLUXDB_USERNAME
|
|
#define INFLUXDB_USERNAME "" // Default username
|
|
#endif
|
|
|
|
#ifndef INFLUXDB_PASSWORD
|
|
#define INFLUXDB_PASSWORD "" // Default password
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// THINGSPEAK
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef THINGSPEAK_SUPPORT
|
|
#define THINGSPEAK_SUPPORT 1 // Enable Thingspeak support by default (2.56Kb)
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_ENABLED
|
|
#define THINGSPEAK_ENABLED 0 // Thingspeak disabled by default
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_APIKEY
|
|
#define THINGSPEAK_APIKEY "" // Default API KEY
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_CLEAR_CACHE
|
|
#define THINGSPEAK_CLEAR_CACHE 1 // Clear cache after sending values
|
|
// Not clearing it will result in latest values for each field being sent every time
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_USE_ASYNC
|
|
#define THINGSPEAK_USE_ASYNC 1 // Use AsyncClient instead of WiFiClientSecure
|
|
#endif
|
|
|
|
// THINGSPEAK OVER SSL
|
|
// Using THINGSPEAK over SSL works well but generates problems with the web interface,
|
|
// so you should compile it with WEB_SUPPORT to 0.
|
|
// When THINGSPEAK_USE_ASYNC is 1, requires EspAsyncTCP to be built with ASYNC_TCP_SSL_ENABLED=1 and ESP8266 Arduino Core >= 2.4.0.
|
|
// When THINGSPEAK_USE_ASYNC is 0, requires Arduino Core >= 2.6.0 and SECURE_CLIENT_BEARSSL
|
|
//
|
|
// WARNING: Thingspeak servers do not support MFLN right now, connection requires at least 30KB of free RAM.
|
|
// Also see MQTT comments above.
|
|
|
|
#ifndef THINGSPEAK_USE_SSL
|
|
#define THINGSPEAK_USE_SSL 0 // Use secure connection
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_SECURE_CLIENT_CHECK
|
|
#define THINGSPEAK_SECURE_CLIENT_CHECK SECURE_CLIENT_CHECK
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_SECURE_CLIENT_MFLN
|
|
#define THINGSPEAK_SECURE_CLIENT_MFLN SECURE_CLIENT_MFLN
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_FINGERPRINT
|
|
#define THINGSPEAK_FINGERPRINT "78 60 18 44 81 35 BF DF 77 84 D4 0A 22 0D 9B 4E 6C DC 57 2C"
|
|
#endif
|
|
|
|
#ifndef THINGSPEAK_ADDRESS
|
|
#if THINGSPEAK_USE_SSL
|
|
#define THINGSPEAK_ADDRESS "https://api.thingspeak.com/update"
|
|
#else
|
|
#define THINGSPEAK_ADDRESS "http://api.thingspeak.com/update"
|
|
#endif
|
|
#endif // ifndef THINGSPEAK_ADDRESS
|
|
|
|
#ifndef THINGSPEAK_TRIES
|
|
#define THINGSPEAK_TRIES 3 // Number of tries when sending data (minimum 1)
|
|
#endif
|
|
|
|
#define THINGSPEAK_MIN_INTERVAL 15000 // Minimum interval between POSTs (in millis)
|
|
#define THINGSPEAK_FIELDS 8 // Number of fields
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// SCHEDULER
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef SCHEDULER_SUPPORT
|
|
#define SCHEDULER_SUPPORT 1 // Enable scheduler (2.45Kb)
|
|
#endif
|
|
|
|
#ifndef SCHEDULER_MAX_SCHEDULES
|
|
#define SCHEDULER_MAX_SCHEDULES 10 // Max schedules alowed
|
|
#endif
|
|
|
|
#ifndef SCHEDULER_RESTORE_LAST_SCHEDULE
|
|
#define SCHEDULER_RESTORE_LAST_SCHEDULE 0 // Restore the last schedule state on the device boot
|
|
#endif
|
|
|
|
#ifndef SCHEDULER_WEEKDAYS
|
|
#define SCHEDULER_WEEKDAYS "1,2,3,4,5,6,7" // (Default - Run the schedules every day)
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// RPN RULES
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef RPN_RULES_SUPPORT
|
|
#define RPN_RULES_SUPPORT 0 // Enable RPN Rules (8.6Kb)
|
|
#endif
|
|
|
|
#ifndef RPN_DELAY
|
|
#define RPN_DELAY 100 // Execute rules after 100ms without messages
|
|
#endif
|
|
|
|
#ifndef RPN_STICKY
|
|
#define RPN_STICKY 1 // Keeps variable after rule execution
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// NTP
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef NTP_SUPPORT
|
|
#define NTP_SUPPORT 1 // Build with NTP support by default (depends on Core version)
|
|
#endif
|
|
|
|
#ifndef NTP_SERVER
|
|
#define NTP_SERVER "pool.ntp.org" // Default NTP server
|
|
#endif
|
|
|
|
#ifndef NTP_TIMEZONE
|
|
#define NTP_TIMEZONE TZ_Etc_UTC // POSIX TZ variable. Default to UTC from TZ.h (which is PSTR("UTC0"))
|
|
// For the format documentation, see:
|
|
// - https://www.gnu.org/software/libc/manual/html_node/TZ-Variable.html
|
|
// ESP8266 Core provides human-readable aliases for POSIX format, see:
|
|
// - Latest: https://github.com/esp8266/Arduino/blob/master/cores/esp8266/TZ.h
|
|
// - PlatformIO: ~/.platformio/packages/framework-arduinoespressif8266/cores/esp8266/TZ.h
|
|
// (or, possibly, c:\.platformio\... on Windows)
|
|
// - Arduino IDE: depends on platform, see `/dist/arduino_ide/README.md`
|
|
#endif
|
|
|
|
#ifndef NTP_UPDATE_INTERVAL
|
|
#define NTP_UPDATE_INTERVAL 1800 // NTP check every 30 minutes
|
|
#endif
|
|
|
|
#ifndef NTP_START_DELAY
|
|
#define NTP_START_DELAY 3 // Delay NTP start for 3 seconds
|
|
#endif
|
|
|
|
#ifndef NTP_WAIT_FOR_SYNC
|
|
#define NTP_WAIT_FOR_SYNC 1 // Do not report any datetime until NTP sync'ed
|
|
#endif
|
|
|
|
#ifndef NTP_DHCP_SERVER
|
|
#define NTP_DHCP_SERVER 1 // Automatically replace the NTP server value with the one received with the DHCP packet
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// ALEXA
|
|
// -----------------------------------------------------------------------------
|
|
|
|
// This setting defines whether Alexa support should be built into the firmware
|
|
#ifndef ALEXA_SUPPORT
|
|
#define ALEXA_SUPPORT 1 // Enable Alexa support by default (10.84Kb)
|
|
#endif
|
|
|
|
// This is default value for the alexaEnabled setting that defines whether
|
|
// this device should be discoberable and respond to Alexa commands.
|
|
// Both ALEXA_SUPPORT and alexaEnabled should be 1 for Alexa support to work.
|
|
#ifndef ALEXA_ENABLED
|
|
#define ALEXA_ENABLED 1
|
|
#endif
|
|
|
|
#ifndef ALEXA_HOSTNAME
|
|
#define ALEXA_HOSTNAME ""
|
|
#endif
|
|
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// RF BRIDGE
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef RFB_SUPPORT
|
|
#define RFB_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef RFB_SEND_REPEATS
|
|
#define RFB_SEND_REPEATS 1 // How many times to send the message
|
|
#endif
|
|
|
|
// - RFB_PROVIDER_EFM8BB1
|
|
// Default option for the ITEAD_SONOFF_RFBRIDGE or any custom firmware implementing the protocol
|
|
// - RFB_PROVIDER_RCSWITCH
|
|
// Originally implemented for SONOFF BASIC
|
|
// https://tinkerman.cat/adding-rf-to-a-non-rf-itead-sonoff/
|
|
// Also possible to use with SONOFF RF BRIDGE, thanks to @wildwiz
|
|
// https://github.com/xoseperez/espurna/wiki/Hardware-Itead-Sonoff-RF-Bridge---Direct-Hack
|
|
#ifndef RFB_PROVIDER
|
|
#define RFB_PROVIDER RFB_PROVIDER_RCSWITCH
|
|
#endif
|
|
|
|
#ifndef RFB_RX_PIN
|
|
#define RFB_RX_PIN GPIO_NONE
|
|
#endif
|
|
|
|
#ifndef RFB_TX_PIN
|
|
#define RFB_TX_PIN GPIO_NONE
|
|
#endif
|
|
|
|
#ifndef RFB_LEARN_TIMEOUT
|
|
#define RFB_LEARN_TIMEOUT 15000
|
|
#endif
|
|
|
|
#ifndef RFB_SEND_DELAY
|
|
#define RFB_SEND_DELAY 500 // Interval between sendings in ms
|
|
#endif
|
|
|
|
#ifndef RFB_RECEIVE_DELAY
|
|
#define RFB_RECEIVE_DELAY 500 // Interval between recieving in ms (avoid bouncing)
|
|
#endif
|
|
|
|
#ifndef RFB_TRANSMIT_REPEATS
|
|
#define RFB_TRANSMIT_REPEATS 5 // How many times RCSwitch will repeat the message
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// IR Bridge
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef IR_SUPPORT
|
|
#define IR_SUPPORT 0 // Do not build with IR support by default (10.25Kb)
|
|
#endif
|
|
|
|
//#define IR_RX_PIN 5 // GPIO the receiver is connected to
|
|
//#define IR_TX_PIN 4 // GPIO the transmitter is connected to
|
|
|
|
#ifndef IR_USE_RAW
|
|
#define IR_USE_RAW 0 // Use raw codes
|
|
#endif
|
|
|
|
#ifndef IR_BUFFER_SIZE
|
|
#define IR_BUFFER_SIZE 1024
|
|
#endif
|
|
|
|
#ifndef IR_TIMEOUT
|
|
#define IR_TIMEOUT 15U
|
|
#endif
|
|
|
|
#ifndef IR_REPEAT
|
|
#define IR_REPEAT 1
|
|
#endif
|
|
|
|
#ifndef IR_DELAY
|
|
#define IR_DELAY 100
|
|
#endif
|
|
|
|
#ifndef IR_DEBOUNCE
|
|
#define IR_DEBOUNCE 500 // IR debounce time in milliseconds
|
|
#endif
|
|
|
|
#ifndef IR_BUTTON_SET
|
|
#define IR_BUTTON_SET 0 // IR button set to use (see ../ir_button.h)
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Custom RFM69 to MQTT bridge
|
|
// Check http://tinkerman.cat/rfm69-wifi-gateway/
|
|
// Enable support by passing RFM69_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef RFM69_SUPPORT
|
|
#define RFM69_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef RFM69_MAX_TOPICS
|
|
#define RFM69_MAX_TOPICS 50
|
|
#endif
|
|
|
|
#ifndef RFM69_MAX_NODES
|
|
#define RFM69_MAX_NODES 255
|
|
#endif
|
|
|
|
#ifndef RFM69_DEFAULT_TOPIC
|
|
#define RFM69_DEFAULT_TOPIC "/rfm69gw/{node}/{key}"
|
|
#endif
|
|
|
|
#ifndef RFM69_NODE_ID
|
|
#define RFM69_NODE_ID 1
|
|
#endif
|
|
|
|
#ifndef RFM69_GATEWAY_ID
|
|
#define RFM69_GATEWAY_ID 1
|
|
#endif
|
|
|
|
#ifndef RFM69_NETWORK_ID
|
|
#define RFM69_NETWORK_ID 164
|
|
#endif
|
|
|
|
#ifndef RFM69_PROMISCUOUS
|
|
#define RFM69_PROMISCUOUS 0
|
|
#endif
|
|
|
|
#ifndef RFM69_PROMISCUOUS_SENDS
|
|
#define RFM69_PROMISCUOUS_SENDS 0
|
|
#endif
|
|
|
|
#ifndef RFM69_FREQUENCY
|
|
#define RFM69_FREQUENCY RF69_868MHZ
|
|
#endif
|
|
|
|
#ifndef RFM69_ENCRYPTKEY
|
|
#define RFM69_ENCRYPTKEY "fibonacci0123456"
|
|
#endif
|
|
|
|
#ifndef RFM69_CS_PIN
|
|
#define RFM69_CS_PIN SS
|
|
#endif
|
|
|
|
#ifndef RFM69_IRQ_PIN
|
|
#define RFM69_IRQ_PIN 5
|
|
#endif
|
|
|
|
#ifndef RFM69_RESET_PIN
|
|
#define RFM69_RESET_PIN 7
|
|
#endif
|
|
|
|
#ifndef RFM69_IS_RFM69HW
|
|
#define RFM69_IS_RFM69HW 0
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// TUYA switch & dimmer support
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef TUYA_SUPPORT
|
|
#define TUYA_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef TUYA_SERIAL
|
|
#define TUYA_SERIAL Serial
|
|
#endif
|
|
|
|
#ifndef TUYA_FILTER_ENABLED
|
|
#define TUYA_FILTER_ENABLED 1
|
|
#endif
|
|
|
|
#ifndef TUYA_DEBUG_ENABLED
|
|
#define TUYA_DEBUG_ENABLED 1
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Support expander MCP23S08
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef MCP23S08_SUPPORT
|
|
#define MCP23S08_SUPPORT 0
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Support prometheus metrics export
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef PROMETHEUS_SUPPORT
|
|
#define PROMETHEUS_SUPPORT 0
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// ITEAD iFan support
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef IFAN_SUPPORT
|
|
#define IFAN_SUPPORT 0
|
|
#endif
|
|
|
|
// =============================================================================
|
|
// Configuration helpers to help detect features
|
|
// =============================================================================
|
|
|
|
#ifndef DEBUG_SUPPORT
|
|
#define DEBUG_SUPPORT ( \
|
|
DEBUG_SERIAL_SUPPORT || \
|
|
DEBUG_UDP_SUPPORT || \
|
|
DEBUG_TELNET_SUPPORT || \
|
|
DEBUG_WEB_SUPPORT \
|
|
)
|
|
#endif
|
|
|
|
#ifndef FAN_SUPPORT
|
|
#define FAN_SUPPORT IFAN_SUPPORT
|
|
#endif
|