Fork of the espurna firmware for `mhsw` switches
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

131 lines
4.7 KiB

//--------------------------------------------------------------------------------
// Custom RF module
// Check http://tinkerman.cat/adding-rf-to-a-non-rf-itead-sonoff/
// Enable support by passing ENABLE_RF=1 build flag
//--------------------------------------------------------------------------------
#define RF_PIN 14
#define RF_CHANNEL 31
#define RF_DEVICE 1
//--------------------------------------------------------------------------------
// DHTXX temperature/humidity sensor
// Enable support by passing ENABLE_DHT=1 build flag
//--------------------------------------------------------------------------------
#define DHT_PIN 14
#define DHT_UPDATE_INTERVAL 60000
#define DHT_TYPE DHT22
#define DHT_TIMING 11
#define DHT_TEMPERATURE_TOPIC "temperature"
#define DHT_HUMIDITY_TOPIC "humidity"
#define HUMIDITY_NORMAL 0
#define HUMIDITY_COMFORTABLE 1
#define HUMIDITY_DRY 2
#define HUMIDITY_WET 3
//--------------------------------------------------------------------------------
// Analog sensor
// Enable support by passing ENABLE_ANALOG=1 build flag
//--------------------------------------------------------------------------------
#define ANALOG_PIN 0
#define ANALOG_UPDATE_INTERVAL 60000
#define ANALOG_TOPIC "analog"
#if ENABLE_ANALOG
#undef ENABLE_ADC_VCC
#define ENABLE_ADC_VCC 0
#endif
//--------------------------------------------------------------------------------
// DS18B20 temperature sensor
// Enable support by passing ENABLE_DS18B20=1 build flag
//--------------------------------------------------------------------------------
#define DS_PIN 14
#define DS_UPDATE_INTERVAL 60000
#define DS_TEMPERATURE_TOPIC "temperature"
//--------------------------------------------------------------------------------
// Custom current sensor
// Check http://tinkerman.cat/your-laundry-is-done/
// Check http://tinkerman.cat/power-monitoring-sonoff-th-adc121/
// Enable support by passing ENABLE_EMON=1 build flag
//--------------------------------------------------------------------------------
#define EMON_ANALOG_PROVIDER 0
#define EMON_ADC121_PROVIDER 1
// If you select EMON_ADC121_PROVIDER you need to enable and configure I2C in general.h
#define EMON_PROVIDER EMON_ANALOG_PROVIDER
#if EMON_PROVIDER == EMON_ANALOG_PROVIDER
#define EMON_CURRENT_PIN 0
#define EMON_ADC_BITS 10
#define EMON_REFERENCE_VOLTAGE 1.0
#define EMON_CURRENT_PRECISION 1
#define EMON_CURRENT_OFFSET 0.25
#if ENABLE_EMON
#undef ENABLE_ADC_VCC
#define ENABLE_ADC_VCC 0
#endif
#endif
#if EMON_PROVIDER == EMON_ADC121_PROVIDER
#define EMON_ADC121_ADDRESS 0x50
#define EMON_ADC_BITS 12
#define EMON_REFERENCE_VOLTAGE 3.3
#define EMON_CURRENT_PRECISION 2
#define EMON_CURRENT_OFFSET 0.10
#endif
#define EMON_CURRENT_RATIO 30
#define EMON_SAMPLES 1000
#define EMON_INTERVAL 10000
#define EMON_MEASUREMENTS 6
#define EMON_MAINS_VOLTAGE 230
#define EMON_APOWER_TOPIC "apower"
#define EMON_ENERGY_TOPIC "energy"
#define EMON_CURRENT_TOPIC "current"
//--------------------------------------------------------------------------------
// HLW8012 power sensor (Sonoff POW, Espurna H)
// Enable support by passing ENABLE_HLW8012=1 build flag
//--------------------------------------------------------------------------------
// GPIOs defined in the hardware.h file
#define HLW8012_USE_INTERRUPTS 1
#define HLW8012_SEL_CURRENT HIGH
#define HLW8012_CURRENT_R 0.001
#define HLW8012_VOLTAGE_R_UP ( 5 * 470000 ) // Real: 2280k
#define HLW8012_VOLTAGE_R_DOWN ( 1000 ) // Real 1.009k
#define HLW8012_POWER_TOPIC "power"
#define HLW8012_CURRENT_TOPIC "current"
#define HLW8012_VOLTAGE_TOPIC "voltage"
#define HLW8012_APOWER_TOPIC "apower"
#define HLW8012_RPOWER_TOPIC "rpower"
#define HLW8012_PFACTOR_TOPIC "pfactor"
#define HLW8012_ENERGY_TOPIC "energy"
#define HLW8012_UPDATE_INTERVAL 5000
#define HLW8012_REPORT_EVERY 12
#define HLW8012_MIN_POWER 5
#define HLW8012_MAX_POWER 2500
#define HLW8012_MIN_CURRENT 0.05
#define HLW8012_MAX_CURRENT 10
//--------------------------------------------------------------------------------
// Internal power montior
// Enable support by passing ENABLE_ADC_VCC=1 build flag
// Do not enable this if using the analog GPIO for any other thing
//--------------------------------------------------------------------------------
#ifndef ENABLE_ADC_VCC
#define ENABLE_ADC_VCC 1
#endif
#if ENABLE_ADC_VCC
ADC_MODE(ADC_VCC);
#endif