mh
/
mhsw-espurna


								// -----------------------------------------------------------------------------

								// SENSORS

								// -----------------------------------------------------------------------------


								#define SENSOR_READ_INTERVAL            6000            // Read data from sensors every 6 seconds

								#define SENSOR_REPORT_EVERY             10              // Report every this many readings

								#define SENSOR_USE_INDEX                0               // Use the index in topic (i.e. temperature/0)

								                                                        // even if just one sensor (0 for backwards compatibility)


								#define SENSOR_TEMPERATURE_UNITS        TMP_CELSIUS     // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)

								#define SENSOR_TEMPERATURE_CORRECTION   0.0             // Offset correction

								#define TEMPERATURE_MIN_CHANGE          0.0             // Minimum temperature change to report

								#define HUMIDITY_MIN_CHANGE             0               // Minimum humidity change to report


								#define SENSOR_TEMPERATURE_DECIMALS     1

								#define SENSOR_HUMIDITY_DECIMALS        0

								#define SENSOR_PRESSURE_DECIMALS        2

								#define SENSOR_ANALOG_DECIMALS          0

								#define SENSOR_EVENTS_DECIMALS          0

								#define SENSOR_CURRENT_DECIMALS         3

								#define SENSOR_VOLTAGE_DECIMALS         0

								#define SENSOR_POWER_DECIMALS           0

								#define SENSOR_POWER_FACTOR_DECIMALS    0

								#define SENSOR_ENERGY_DECIMALS          0

								#define SENSOR_PM1dot0_DECIMALS         0

								#define SENSOR_PM2dot5_DECIMALS         0

								#define SENSOR_PM10_DECIMALS            0

								#define SENSOR_CO2_DECIMALS             0


								#define SENSOR_UNKNOWN_TOPIC            "unknown"

								#define SENSOR_TEMPERATURE_TOPIC        "temperature"

								#define SENSOR_HUMIDITY_TOPIC           "humidity"

								#define SENSOR_PRESSURE_TOPIC           "pressure"

								#define SENSOR_CURRENT_TOPIC            "current"

								#define SENSOR_VOLTAGE_TOPIC            "voltage"

								#define SENSOR_ACTIVE_POWER_TOPIC       "power"

								#define SENSOR_APPARENT_POWER_TOPIC     "apparent"

								#define SENSOR_REACTIVE_POWER_TOPIC     "reactive"

								#define SENSOR_POWER_FACTOR_TOPIC       "factor"

								#define SENSOR_ENERGY_TOPIC             "energy"

								#define SENSOR_ENERGY_DELTA_TOPIC       "energy_delta"

								#define SENSOR_PM1dot0_TOPIC            "pm1dot0"

								#define SENSOR_PM2dot5_TOPIC            "pm2dot5"

								#define SENSOR_PM10_TOPIC               "pm10"

								#define SENSOR_ANALOG_TOPIC             "analog"

								#define SENSOR_DIGITAL_TOPIC            "digital"

								#define SENSOR_EVENTS_TOPIC             "events"

								#define SENSOR_CO2_TOPIC                "co2"


								//--------------------------------------------------------------------------------

								// DHTXX temperature/humidity sensor

								// Enable support by passing DHT_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef DHT_SUPPORT

								#define DHT_SUPPORT                 0

								#endif


								#ifndef DHT_PIN

								#define DHT_PIN                     14

								#endif


								#ifndef DHT_TYPE

								#define DHT_TYPE                    DHT22

								#endif


								#ifndef DHT_PULLUP

								#define DHT_PULLUP                  0

								#endif


								#ifndef DHT_UPDATE_INTERVAL

								#define DHT_UPDATE_INTERVAL         60000

								#endif


								#define DHT_TEMPERATURE_TOPIC       "temperature"

								#define DHT_HUMIDITY_TOPIC          "humidity"


								#define HUMIDITY_NORMAL             0

								#define HUMIDITY_COMFORTABLE        1

								#define HUMIDITY_DRY                2

								#define HUMIDITY_WET                3


								//--------------------------------------------------------------------------------

								// SI7021 temperature & humidity sensor

								// Enable support by passing SI7021_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef SI7021_SUPPORT

								#define SI7021_SUPPORT              0

								#endif


								#ifndef SI7021_ADDRESS

								#define SI7021_ADDRESS              0x40

								#endif


								//--------------------------------------------------------------------------------

								// BME280

								// Enable support by passing BME280_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef BME280_SUPPORT

								#define BME280_SUPPORT              0

								#endif


								#ifndef BME280_ADDRESS

								#define BME280_ADDRESS              0x76

								#endif


								#define BME280_MODE                 1       // 1 for forced mode, 3 for normal mode

								#define BME280_TEMPERATURE          1       // Oversampling for temperature (set to 0 to disable magnitude)

								#define BME280_HUMIDITY             1       // Oversampling for humidity (set to 0 to disable magnitude)

								#define BME280_PRESSURE             1       // Oversampling for pressure (set to 0 to disable magnitude)


								//--------------------------------------------------------------------------------

								// DS18B20 temperature sensor

								// Enable support by passing DS18B20_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef DS18B20_SUPPORT

								#define DS18B20_SUPPORT             0

								#endif


								#ifndef DS18B20_PIN

								#define DS18B20_PIN                 13

								#endif


								#ifndef DS18B20_PULLUP

								#define DS18B20_PULLUP              1

								#endif


								#ifndef DS18B20_UPDATE_INTERVAL

								#define DS18B20_UPDATE_INTERVAL     60000

								#endif


								#ifndef DS18B20_TEMPERATURE_TOPIC

								#define DS18B20_TEMPERATURE_TOPIC   "temperature"

								#endif


								#define DS18B20_RESOLUTION          9


								//--------------------------------------------------------------------------------

								// Digital sensor

								// Enable support by passing DIGITAL_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef DIGITAL_SUPPORT

								#define DIGITAL_SUPPORT             0

								#endif


								#ifndef DIGITAL_PIN

								#define DIGITAL_PIN                 2

								#endif


								#ifndef DIGITAL_PIN_MODE

								#define DIGITAL_PIN_MODE            INPUT_PULLUP

								#endif


								#ifndef DIGITAL_DEFAULT_STATE

								#define DIGITAL_DEFAULT_STATE       1

								#endif


								//--------------------------------------------------------------------------------

								// Analog sensor

								// Enable support by passing ANALOG_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef ANALOG_SUPPORT

								#define ANALOG_SUPPORT              0

								#endif


								#ifndef ANALOG_PIN

								#define ANALOG_PIN                  0

								#endif


								#ifndef ANALOG_PIN_MODE

								#define ANALOG_PIN_MODE             INPUT

								#endif


								#if ANALOG_SUPPORT

								    #undef ADC_VCC_ENABLED

								    #define ADC_VCC_ENABLED         0

								#endif


								//--------------------------------------------------------------------------------

								// Counter sensor

								// Enable support by passing COUNTER_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef COUNTER_SUPPORT

								#define COUNTER_SUPPORT             0           // Do not build with counter support by default

								#endif


								#ifndef COUNTER_PIN

								#define COUNTER_PIN                 2           // GPIO to monitor

								#endif


								#ifndef COUNTER_PIN_MODE

								#define COUNTER_PIN_MODE            INPUT       // INPUT, INPUT_PULLUP

								#endif


								#ifndef COUNTER_INTERRUPT_MODE

								#define COUNTER_INTERRUPT_MODE      RISING      // RISING, FALLING, BOTH

								#endif


								#define COUNTER_DEBOUNCE            50          // Do not register events within less than 10 millis


								//--------------------------------------------------------------------------------

								// Energy Monitor

								//--------------------------------------------------------------------------------


								#define EMON_MAX_SAMPLES            1000        // Max number of samples to get

								#define EMON_MAX_TIME               250         // Max time in ms to sample

								#define EMON_FILTER_SPEED           512         // Mobile average filter speed

								#define EMON_MAINS_VOLTAGE          230         // Mains voltage

								#define EMON_REPORT_CURRENT         0           // Calculate current

								#define EMON_REPORT_POWER           1           // Calculate power

								#define EMON_REPORT_ENERGY          1           // Calculate energy


								//--------------------------------------------------------------------------------

								// Energy Monitor based on interval analog GPIO

								// Enable support by passing EMON_ANALOG_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef EMON_ANALOG_SUPPORT

								#define EMON_ANALOG_SUPPORT             0       // Do not build support by default

								#endif


								#define EMON_ANALOG_CURRENT_RATIO       30      // Current ratio in the clamp (30V/1A)

								#define EMON_ANALOG_ADC_BITS            10      // ADC depth

								#define EMON_ANALOG_REFERENCE_VOLTAGE   3.3     // Reference voltage of the ADC


								#if EMON_ANALOG_SUPPORT

								    #undef ADC_VCC_ENABLED

								    #define ADC_VCC_ENABLED             0

								#endif


								//--------------------------------------------------------------------------------

								// Energy Monitor based on ADC121

								// Enable support by passing EMON_ADC121_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef EMON_ADC121_SUPPORT

								#define EMON_ADC121_SUPPORT             0       // Do not build support by default

								#endif


								#define EMON_ADC121_I2C_ADDRESS         0x50    // I2C address of the ADC121


								#define EMON_ADC121_CURRENT_RATIO       30      // Current ratio in the clamp (30V/1A)

								#define EMON_ADC121_ADC_BITS            12      // ADC depth

								#define EMON_ADC121_REFERENCE_VOLTAGE   3.3     // Reference voltage of the ADC


								//--------------------------------------------------------------------------------

								// Energy Monitor based on ADS1X15

								// Enable support by passing EMON_ADS1X15_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef EMON_ADS1X15_SUPPORT

								#define EMON_ADS1X15_SUPPORT            0       // Do not build support by default

								#endif


								#define EMON_ADS1X15_ADS1115            1       // 0 for ADS10115, 1 for ADS1115

								#define EMON_ADS1X15_PORT_MASK          0x08    // A0=1 A1=2 A2=4 A4=8

								#define EMON_ADS1X15_I2C_ADDRESS        0x48    // I2C address of the ADS1115


								#define EMON_ADS1X15_CURRENT_RATIO      30      // Current ratio in the clamp (30V/1A)

								#define EMON_ADS1X15_ADC_BITS           16      // ADC depth

								#define EMON_ADS1X15_REFERENCE_VOLTAGE  8.192   // Double the gain for peak-to-peak


								//--------------------------------------------------------------------------------

								// Particle Monitor based on Plantower PMSX003

								// Enable support by passing PMSX003_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef PMSX003_SUPPORT

								#define PMSX003_SUPPORT                 0

								#endif


								#define PMS_RX_PIN                      13

								#define PMS_TX_PIN                      15


								//--------------------------------------------------------------------------------

								// MHZ19 CO2 sensor

								// Enable support by passing MHZ19_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef MHZ19_SUPPORT

								#define MHZ19_SUPPORT                   1

								#endif


								#define MHZ19_RX_PIN                    13

								#define MHZ19_TX_PIN                    15


								//--------------------------------------------------------------------------------

								// Internal power montior

								// Enable support by passing ADC_VCC_ENABLED=1 build flag

								// Do not enable this if using the analog GPIO for any other thing

								//--------------------------------------------------------------------------------


								#ifndef ADC_VCC_ENABLED

								#define ADC_VCC_ENABLED             1

								#endif


								#if ADC_VCC_ENABLED

								    ADC_MODE(ADC_VCC);

								#endif