Fork of the espurna firmware for `mhsw` switches
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

1804 lines
55 KiB

// -----------------------------------------------------------------------------
// Configuration HELP
// -----------------------------------------------------------------------------
//
// MANUFACTURER: Name of the manufacturer of the board ("string")
// DEVICE: Name of the device ("string")
// BUTTON#_PIN: GPIO for the n-th button (1-based, up to 4 buttons)
// BUTTON#_RELAY: Relay number that will be bind to the n-th button (1-based)
// BUTTON#_MODE: A mask of options (BUTTON_PUSHBUTTON and BUTTON_SWITCH cannot be together)
// - BUTTON_PUSHBUTTON: button event is fired when released
// - BUTTON_SWITCH: button event is fired when pressed or released
// - BUTTON_DEFAULT_HIGH: there is a pull up in place
// - BUTTON_SET_PULLUP: set pullup by software
// RELAY#_PIN: GPIO for the n-th relay (1-based, up to 8 relays)
// RELAY#_TYPE: Relay can be RELAY_TYPE_NORMAL, RELAY_TYPE_INVERSE, RELAY_TYPE_LATCHED or RELAY_TYPE_LATCHED_INVERSE
// LED#_PIN: GPIO for the n-th LED (1-based, up to 8 LEDs)
// LED#_PIN_INVERSE: LED has inversed logic (lit when pulled down)
// LED#_MODE: Check general.h for LED_MODE_%
// LED#_RELAY: Linked relay (1-based)
//
// Besides, other hardware specific information should be stated here
// -----------------------------------------------------------------------------
// ESPurna Core
// -----------------------------------------------------------------------------
#if defined(ESPURNA_CORE)
// This is a special device targeted to generate a light-weight binary image
// meant to be able to do two-step-updates:
// https://github.com/xoseperez/espurna/wiki/TwoStepUpdates
// Info
#define MANUFACTURER "ESPRESSIF"
#define DEVICE "ESPURNA_CORE"
// Disable non-core modules
#define ALEXA_SUPPORT 0
#define BROKER_SUPPORT 0
#define DOMOTICZ_SUPPORT 0
#define HOMEASSISTANT_SUPPORT 0
#define I2C_SUPPORT 0
#define MQTT_SUPPORT 0
#define NTP_SUPPORT 0
#define SCHEDULER_SUPPORT 0
#define SENSOR_SUPPORT 0
#define THINGSPEAK_SUPPORT 0
#define WEB_SUPPORT 0
// -----------------------------------------------------------------------------
// Development boards
// -----------------------------------------------------------------------------
#elif defined(NODEMCU_LOLIN)
// Info
#define MANUFACTURER "NODEMCU"
#define DEVICE "LOLIN"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
#elif defined(WEMOS_D1_MINI_RELAYSHIELD)
// Info
#define MANUFACTURER "WEMOS"
#define DEVICE "D1_MINI_RELAYSHIELD"
// Buttons
// No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems
#define BUTTON1_PIN 0 // Connect a pushbutton between D3 and GND,
// it's the same as using a Wemos one button shield
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// When Wemos relay shield is connected GPIO5 (D1) is used for relay,
// so I2C must be remapped to other pins
#define I2C_SDA_PIN 12 // D6
#define I2C_SCL_PIN 14 // D5
#elif defined(WEMOS_D1_TARPUNA_SHIELD)
// Info
#define MANUFACTURER "WEMOS"
#define DEVICE "D1_TARPUNA_SHIELD"
// -----------------------------------------------------------------------------
// ESPurna
// -----------------------------------------------------------------------------
#elif defined(TINKERMAN_ESPURNA_H06)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_H06"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Normal pushbutton
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 2
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(TINKERMAN_ESPURNA_H08)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_H08"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Normal pushbutton
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 5
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(TINKERMAN_ESPURNA_SWITCH)
// Info
#define MANUFACTURER "TINKERMAN"
#define DEVICE "ESPURNA_SWITCH"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_RELAY 1
// Touch button
#define BUTTON1_MODE BUTTON_PUSHBUTTON
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_INVERSE
// -----------------------------------------------------------------------------
// Itead Studio boards
// -----------------------------------------------------------------------------
#elif defined(ITEAD_SONOFF_BASIC)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_BASIC"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 14
#define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_RF)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_RF"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_PIN 14
#define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_TH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_TH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Jack is connected to GPIO14 (and with a small hack to GPIO4)
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 14
#ifndef DHT_SUPPORT
#define DHT_SUPPORT 1
#endif
#define DHT_PIN 14
//#define I2C_SDA_PIN 4
//#define I2C_SCL_PIN 14
#elif defined(ITEAD_SONOFF_SV)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_SV"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SLAMPHER)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SLAMPHER"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_S20)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "S20"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_TOUCH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_TOUCH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_POW)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_POW"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 15
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 5
#define HLW8012_CF1_PIN 13
#define HLW8012_CF_PIN 14
#elif defined(ITEAD_SONOFF_DUAL)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_DUAL"
#define SERIAL_BAUDRATE 19230
#define RELAY_PROVIDER RELAY_PROVIDER_DUAL
#define DUMMY_RELAY_COUNT 2
#define DEBUG_SERIAL_SUPPORT 0
#define TERMINAL_SUPPORT 0
// Buttons
#define BUTTON3_RELAY 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_DUAL_R2)
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_DUAL_R2"
// Buttons
#define BUTTON1_PIN 0 // Button 0 on header
#define BUTTON2_PIN 9 // Button 1 on header
#define BUTTON3_PIN 10 // Physical button
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 1
#define BUTTON1_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_4CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_4CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON4_PIN 14
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
#define BUTTON4_RELAY 4
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_4CH_PRO)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_4CH_PRO"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON4_PIN 14
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON4_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
#define BUTTON4_RELAY 4
// Sonoff 4CH Pro uses a secondary STM32 microcontroller to handle
// buttons and relays, but it also forwards button presses to the ESP8285.
// This allows ESPurna to handle button presses -almost- the same way
// as with other devices except:
// * Double click seems to break/disable the button on the STM32 side
// * With S6 switch to 1 (self-locking and inching modes) everything's OK
// * With S6 switch to 0 (interlock mode) if there is a relay ON
// and you click on another relay button, the STM32 sends a "press"
// event for the button of the first relay (to turn it OFF) but it
// does not send a "release" event. It's like it's holding the
// button down since you can see it is still LOW.
// Whatever reason the result is that it may actually perform a
// long click or long-long click.
// The configuration below make the button toggle the relay on press events
// and disables any possibly harmful combination with S6 set to 0.
// If you are sure you will only use S6 to 1 you can comment the
// BUTTON1_LNGCLICK and BUTTON1_LNGLNGCLICK options below to recover the
// reset mode and factory reset functionalities, or link other actions like
// AP mode in the commented line below.
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
//#define BUTTON1_LNGCLICK BUTTON_MODE_AP
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE
#define BUTTON2_PRESS BUTTON_MODE_TOGGLE
#define BUTTON2_CLICK BUTTON_MODE_NONE
#define BUTTON3_PRESS BUTTON_MODE_TOGGLE
#define BUTTON3_CLICK BUTTON_MODE_NONE
#define BUTTON4_PRESS BUTTON_MODE_TOGGLE
#define BUTTON4_CLICK BUTTON_MODE_NONE
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY4_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_1CH_INCHING)
// The inching functionality is managed by a misterious IC in the board.
// You cannot control the inching button and functionality from the ESP8266
// Besides, enabling the inching functionality using the hardware button
// will result in the relay switching on and off continuously.
// Fortunately the unkown IC keeps memory of the hardware inching status
// so you can just disable it and forget. The inching LED must be lit.
// You can still use the pulse options from the web interface
// without problem.
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "1CH_INCHING"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_MOTOR)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "MOTOR"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_BNSZ01)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "BNSZ01"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 1
#define LIGHT_CH1_PIN 12
#define LIGHT_CH1_INVERSE 0
#elif defined(ITEAD_SONOFF_RFBRIDGE)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_RFBRIDGE"
#define SERIAL_BAUDRATE 19200
#define RELAY_PROVIDER RELAY_PROVIDER_RFBRIDGE
#ifndef DUMMY_RELAY_COUNT
#define DUMMY_RELAY_COUNT 8
#endif
// Remove UART noise on serial line
#define TERMINAL_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_B1)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_B1"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define MY92XX_MODEL MY92XX_MODEL_MY9231
#define MY92XX_CHIPS 2
#define MY92XX_DI_PIN 12
#define MY92XX_DCKI_PIN 14
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 4, 3, 5, 0, 1
#elif defined(ITEAD_SONOFF_LED)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_LED"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 12 // Cold white
#define LIGHT_CH2_PIN 14 // Warm white
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#elif defined(ITEAD_SONOFF_T1_1CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_1CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_T1_2CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_2CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_MODE_TOGGLE
#define BUTTON2_CLICK BUTTON_MODE_NONE
#define BUTTON2_DBLCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
#elif defined(ITEAD_SONOFF_T1_3CH)
// Info
#define MANUFACTURER "ITEAD"
#define DEVICE "SONOFF_T1_3CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON3_PIN 10
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_PRESS BUTTON_MODE_TOGGLE
#define BUTTON2_CLICK BUTTON_MODE_NONE
#define BUTTON2_DBLCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGCLICK BUTTON_MODE_NONE
#define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON3_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON3_PRESS BUTTON_MODE_TOGGLE
#define BUTTON3_CLICK BUTTON_MODE_NONE
#define BUTTON3_DBLCLICK BUTTON_MODE_NONE
#define BUTTON3_LNGCLICK BUTTON_MODE_NONE
#define BUTTON3_LNGLNGCLICK BUTTON_MODE_RESET
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
#define BUTTON3_RELAY 3
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY3_PIN 4
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// YJZK
// -----------------------------------------------------------------------------
#elif defined(YJZK_SWITCH_2CH)
// Info
#define MANUFACTURER "YJZK"
#define DEVICE "SWITCH_2CH"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 9
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Electrodragon boards
// -----------------------------------------------------------------------------
#elif defined(ELECTRODRAGON_WIFI_IOT)
// Info
#define MANUFACTURER "ELECTRODRAGON"
#define DEVICE "WIFI_IOT"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON2_PIN 2
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 16
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// WorkChoice ecoPlug
// -----------------------------------------------------------------------------
#elif defined(WORKCHOICE_ECOPLUG)
// Info
#define MANUFACTURER "WORKCHOICE"
#define DEVICE "ECOPLUG"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// AI Thinker
// -----------------------------------------------------------------------------
#elif defined(AITHINKER_AI_LIGHT)
// Info
#define MANUFACTURER "AITHINKER"
#define DEVICE "AI_LIGHT"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 13
#define MY92XX_DCKI_PIN 15
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// LED Controller
// -----------------------------------------------------------------------------
#elif defined(MAGICHOME_LED_CONTROLLER)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "LED_CONTROLLER"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
// IR
#define IR_SUPPORT 1
#define IR_PIN 4
#define IR_BUTTON_SET 1
#elif defined(MAGICHOME_LED_CONTROLLER_20)
// Info
#define MANUFACTURER "MAGICHOME"
#define DEVICE "LED_CONTROLLER_20"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
// IR
#define IR_SUPPORT 1
#define IR_PIN 4
#define IR_BUTTON_SET 1
// -----------------------------------------------------------------------------
// HUACANXING H801 & H802
// -----------------------------------------------------------------------------
#elif defined(HUACANXING_H801)
// Info
#define MANUFACTURER "HUACANXING"
#define DEVICE "H801"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define DEBUG_PORT Serial1
#define SERIAL_RX_ENABLED 1
// LEDs
#define LED1_PIN 5
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 15 // RED
#define LIGHT_CH2_PIN 13 // GREEN
#define LIGHT_CH3_PIN 12 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE1
#define LIGHT_CH5_PIN 4 // WHITE2
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_CH5_INVERSE 0
#elif defined(HUACANXING_H802)
// Info
#define MANUFACTURER "HUACANXING"
#define DEVICE "H802"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define DEBUG_PORT Serial1
#define SERIAL_RX_ENABLED 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 14 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
// -----------------------------------------------------------------------------
// Jan Goedeke Wifi Relay
// https://github.com/JanGoe/esp8266-wifi-relay
// -----------------------------------------------------------------------------
#elif defined(JANGOE_WIFI_RELAY_NC)
// Info
#define MANUFACTURER "JANGOE"
#define DEVICE "WIFI_RELAY_NC"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON2_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 2
#define RELAY2_PIN 14
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_TYPE RELAY_TYPE_INVERSE
#elif defined(JANGOE_WIFI_RELAY_NO)
// Info
#define MANUFACTURER "JANGOE"
#define DEVICE "WIFI_RELAY_NO"
// Buttons
#define BUTTON1_PIN 12
#define BUTTON2_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 2
#define RELAY2_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// Jorge García Wifi+Relays Board Kit
// https://www.tindie.com/products/jorgegarciadev/wifi--relays-board-kit
// https://github.com/jorgegarciadev/wifikit
// -----------------------------------------------------------------------------
#elif defined(JORGEGARCIA_WIFI_RELAYS)
// Info
#define MANUFACTURER "JORGEGARCIA"
#define DEVICE "WIFI_RELAYS"
// Relays
#define RELAY1_PIN 0
#define RELAY2_PIN 2
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_TYPE RELAY_TYPE_INVERSE
// -----------------------------------------------------------------------------
// WiFi MQTT Relay / Thermostat
// -----------------------------------------------------------------------------
#elif defined(OPENENERGYMONITOR_MQTT_RELAY)
// Info
#define MANUFACTURER "OPENENERGYMONITOR"
#define DEVICE "MQTT_RELAY"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 16
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// WiOn 50055 Indoor Wi-Fi Wall Outlet & Tap
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50050-Indoor-Wi-Fi-Outlet-Wireless-Switch-Programmable-Timer-%2F263112281551
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50055-Indoor-Wi-Fi-Wall-Tap-Monitor-Energy-Usage-Wireless-Smart-Switch-%2F263020837777
// -----------------------------------------------------------------------------
#elif defined(WION_50055)
// Currently untested, does not support energy monitoring
// Info
#define MANUFACTURER "WION"
#define DEVICE "50055"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 15
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 2
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// EX-Store Wifi Relay v3.1
// https://ex-store.de/ESP8266-WiFi-Relay-V31
// -----------------------------------------------------------------------------
#elif defined(EXS_WIFI_RELAY_V31)
// Untested
// Info
#define MANUFACTURER "EXS"
#define DEVICE "WIFI_RELAY_V31"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_RELAY 1
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
// Relays
#define RELAY1_PIN 13
#define RELAY1_TYPE RELAY_TYPE_LATCHED
#define RELAY1_RESET_PIN 12
// -----------------------------------------------------------------------------
// V9261F
// -----------------------------------------------------------------------------
#elif defined(GENERIC_V9261F)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "V9261F"
#define ALEXA_SUPPORT 0
// V9261F
#define V9261F_SUPPORT 1
#define V9261F_PIN 2
#define V9261F_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// ECH1560
// -----------------------------------------------------------------------------
#elif defined(GENERIC_ECH1560)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "ECH1560"
#define ALEXA_SUPPORT 0
// ECH1560
#define ECH1560_SUPPORT 1
#define ECH1560_CLK_PIN 4
#define ECH1560_MISO_PIN 5
#define ECH1560_INVERTED 0
// -----------------------------------------------------------------------------
// ESPLive
// https://github.com/ManCaveMade/ESP-Live
// -----------------------------------------------------------------------------
#elif defined(MANCAVEMADE_ESPLIVE)
// Info
#define MANUFACTURER "MANCAVEMADE"
#define DEVICE "ESPLIVE"
// Buttons
#define BUTTON1_PIN 4
#define BUTTON2_PIN 5
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON2_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
#define BUTTON2_RELAY 2
// Relays
#define RELAY1_PIN 12
#define RELAY2_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// DB18B20
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 2
#define DALLAS_UPDATE_INTERVAL 5000
#define TEMPERATURE_MIN_CHANGE 1.0
// -----------------------------------------------------------------------------
// QuinLED
// http://blog.quindorian.org/2017/02/esp8266-led-lighting-quinled-v2-6-pcb.html
// -----------------------------------------------------------------------------
#elif defined(INTERMITTECH_QUINLED)
// Info
#define MANUFACTURER "INTERMITTECH"
#define DEVICE "QUINLED"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// LEDs
#define LED1_PIN 5
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 2
#define LIGHT_CH1_PIN 0
#define LIGHT_CH2_PIN 2
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
// -----------------------------------------------------------------------------
// Arilux AL-LC06
// -----------------------------------------------------------------------------
#elif defined(ARILUX_AL_LC01)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC01"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 14 // WHITE1
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#elif defined(ARILUX_AL_LC02)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC02"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 12 // RED
#define LIGHT_CH2_PIN 5 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE1
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#elif defined(ARILUX_AL_LC06)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC06"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 14 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH4_PIN 15 // WHITE1
#define LIGHT_CH5_PIN 5 // WHITE2
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_CH5_INVERSE 0
#elif defined(ARILUX_AL_LC11)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "AL_LC11"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 5
#define LIGHT_CH1_PIN 5 // RED
#define LIGHT_CH2_PIN 4 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 13 // WHITE1
#define LIGHT_CH5_PIN 12 // WHITE1
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_CH5_INVERSE 0
#elif defined(ARILUX_E27)
// Info
#define MANUFACTURER "ARILUX"
#define DEVICE "E27"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define MY92XX_MODEL MY92XX_MODEL_MY9291
#define MY92XX_CHIPS 1
#define MY92XX_DI_PIN 13
#define MY92XX_DCKI_PIN 15
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 0, 1, 2, 3
// -----------------------------------------------------------------------------
// XENON SM-PW701U
// -----------------------------------------------------------------------------
#elif defined(XENON_SM_PW702U)
// Info
#define MANUFACTURER "XENON"
#define DEVICE "SM_PW702U"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// AUTHOMETION LYT8266
// https://authometion.com/shop/en/home/13-lyt8266.html
// -----------------------------------------------------------------------------
#elif defined(AUTHOMETION_LYT8266)
// Info
#define MANUFACTURER "AUTHOMETION"
#define DEVICE "LYT8266"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Light
#define LIGHT_CHANNELS 4
#define LIGHT_CH1_PIN 13 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 14 // BLUE
#define LIGHT_CH4_PIN 2 // WHITE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
#define LIGHT_CH4_INVERSE 0
#define LIGHT_ENABLE_PIN 15
#elif defined(GIZWITS_WITTY_CLOUD)
// Info
#define MANUFACTURER "GIZWITS"
#define DEVICE "WITTY_CLOUD"
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
// Buttons
#define BUTTON1_PIN 4
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_PRESS BUTTON_MODE_TOGGLE
#define BUTTON1_CLICK BUTTON_MODE_NONE
#define BUTTON1_DBLCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGCLICK BUTTON_MODE_NONE
#define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
#define ANALOG_SUPPORT 1
// LEDs
#define LED1_PIN 2 // BLUE build-in
#define LED1_PIN_INVERSE 1
// Light
#define LIGHT_CHANNELS 3
#define LIGHT_CH1_PIN 15 // RED
#define LIGHT_CH2_PIN 12 // GREEN
#define LIGHT_CH3_PIN 13 // BLUE
#define LIGHT_CH1_INVERSE 0
#define LIGHT_CH2_INVERSE 0
#define LIGHT_CH3_INVERSE 0
// -----------------------------------------------------------------------------
// KMC 70011
// https://www.amazon.com/KMC-Monitoring-Required-Control-Compatible/dp/B07313TH7B
// -----------------------------------------------------------------------------
#elif defined(KMC_70011)
// Info
#define MANUFACTURER "KMC"
#define DEVICE "70011"
// Buttons
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 14
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 13
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor
// -----------------------------------------------------------------------------
// Euromate (?) Wifi Stecker Shuko
// https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko/p/2291706
// Thanks to @Geitde
// -----------------------------------------------------------------------------
#elif defined(EUROMATE_WIFI_STECKER_SCHUKO)
// Info
#define MANUFACTURER "EUROMATE"
#define DEVICE "WIFI_STECKER_SCHUKO"
// Buttons
#define BUTTON1_PIN 14
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// The relay in the device is not a bistable (latched) relay.
// The device is reported to have a flip-flop circuit to drive the relay
// So @Geitde hack is still the only possible
// Hack: drive GPIO12 low and use GPIO5 as normal relay pin:
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define LED2_PIN 12 /* DUMMY: exploit default off state for GPIO12=low */
#define LED2_PIN_INVERSE 0
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// Generic 8CH
// -----------------------------------------------------------------------------
#elif defined(GENERIC_8CH)
// Info
#define MANUFACTURER "GENERIC"
#define DEVICE "8CH"
// Relays
#define RELAY1_PIN 0
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_PIN 2
#define RELAY2_TYPE RELAY_TYPE_NORMAL
#define RELAY3_PIN 4
#define RELAY3_TYPE RELAY_TYPE_NORMAL
#define RELAY4_PIN 5
#define RELAY4_TYPE RELAY_TYPE_NORMAL
#define RELAY5_PIN 12
#define RELAY5_TYPE RELAY_TYPE_NORMAL
#define RELAY6_PIN 13
#define RELAY6_TYPE RELAY_TYPE_NORMAL
#define RELAY7_PIN 14
#define RELAY7_TYPE RELAY_TYPE_NORMAL
#define RELAY8_PIN 15
#define RELAY8_TYPE RELAY_TYPE_NORMAL
// -----------------------------------------------------------------------------
// STM RELAY
// -----------------------------------------------------------------------------
#elif defined(STM_RELAY)
// Info
#define MANUFACTURER "STM_RELAY"
#define DEVICE "2CH"
// Relays
#define DUMMY_RELAY_COUNT 2
#define RELAY_PROVIDER RELAY_PROVIDER_STM
// Remove UART noise on serial line
#define TERMINAL_SUPPORT 0
#define DEBUG_SERIAL_SUPPORT 0
// -----------------------------------------------------------------------------
// Tonbux Powerstrip02
// -----------------------------------------------------------------------------
#elif defined(TONBUX_POWERSTRIP02)
// Info
#define MANUFACTURER "TONBUX"
#define DEVICE "POWERSTRIP02"
// Buttons
#define BUTTON1_PIN 5
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 0
// Relays
#define RELAY1_PIN 4
#define RELAY1_TYPE RELAY_TYPE_INVERSE
#define RELAY2_PIN 13
#define RELAY2_TYPE RELAY_TYPE_INVERSE
#define RELAY3_PIN 12
#define RELAY3_TYPE RELAY_TYPE_INVERSE
#define RELAY4_PIN 14
#define RELAY4_TYPE RELAY_TYPE_INVERSE
// Not a relay. USB ports on/off
#define RELAY5_PIN 16
#define RELAY5_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0 // 1 blue led
#define LED1_PIN_INVERSE 1
#define LED2_PIN 3 // 3 red leds
#define LED2_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// Lingan SWA1
// -----------------------------------------------------------------------------
#elif defined(LINGAN_SWA1)
// Info
#define MANUFACTURER "LINGAN"
#define DEVICE "SWA1"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 5
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 1
// -----------------------------------------------------------------------------
// HEYGO HY02
// -----------------------------------------------------------------------------
#elif defined(HEYGO_HY02)
// Info
#define MANUFACTURER "HEYGO"
#define DEVICE "HY02"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 0
#define LED1_PIN_INVERSE 0
#define LED2_PIN 15
#define LED2_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 3
#define HLW8012_CF1_PIN 14
#define HLW8012_CF_PIN 5
#define HLW8012_VOLTAGE_R_UP ( 2 * 1200000 ) // Upstream voltage resistor
// -----------------------------------------------------------------------------
// Maxcio W-US002S
// -----------------------------------------------------------------------------
#elif defined(MAXCIO_WUS002S)
// Info
#define MANUFACTURER "MAXCIO"
#define DEVICE "WUS002S"
// Buttons
#define BUTTON1_PIN 2
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 13
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 3
#define LED1_PIN_INVERSE 0
// HLW8012
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 12
#define HLW8012_CF1_PIN 5
#define HLW8012_CF_PIN 4
#define HLW8012_CURRENT_R 0.002 // Current resistor
#define HLW8012_VOLTAGE_R_UP ( 2 * 1000000 ) // Upstream voltage resistor
// -----------------------------------------------------------------------------
// YiDian XS-SSA05
// -----------------------------------------------------------------------------
#elif defined(YIDIAN_XSSSA05)
// Info
#define MANUFACTURER "YIDIAN"
#define DEVICE "XSSSA05"
// Buttons
#define BUTTON1_PIN 13
#define BUTTON1_MODE BUTTON_PUSHBUTTON
#define BUTTON1_RELAY 1
// Relays
#define RELAY1_PIN 12
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// LEDs
#define LED1_PIN 4
#define LED1_PIN_INVERSE 0
// -----------------------------------------------------------------------------
// TEST boards (do not use!!)
// -----------------------------------------------------------------------------
#elif defined(TRAVIS01)
// Info
#define MANUFACTURER "TravisCI"
#define DEVICE "Virtual board 01"
// Some buttons - pin 0
#define BUTTON1_PIN 0
#define BUTTON1_MODE BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
#define BUTTON1_RELAY 1
// Some relays - pin 1
#define RELAY1_PIN 1
#define RELAY1_TYPE RELAY_TYPE_NORMAL
// Some LEDs - pin 2
#define LED1_PIN 2
#define LED1_PIN_INVERSE 1
// A bit of I2C - pins 3,4
#define I2C_SDA_PIN 3
#define I2C_SCL_PIN 4
// And, as they say in "From Dusk till Dawn":
// This is a sensor blow out!
// Alright, we got white sensor, black sensor, spanish sensor, yellow sensor. We got hot sensor, cold sensor.
// We got wet sensor. We got smelly sensor. We got hairy sensor, bloody sensor. We got snapping sensor.
// We got silk sensor, velvet sensor, naugahyde sensor. We even got horse sensor, dog sensor, chicken sensor.
// C'mon, you want sensor, come on in sensor lovers!
// If we don’t got it, you don't want it!
#define BH1750_SUPPORT 1
#define BMX280_SUPPORT 1
#define SHT3X_I2C_SUPPORT 1
#define EMON_ADC121_SUPPORT 1
#define EMON_ADS1X15_SUPPORT 1
#define SHT3X_I2C_SUPPORT 1
#define SI7021_SUPPORT 1
// A bit of lights - pin 5
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_DIMMER
#define DUMMY_RELAY_COUNT 1
#define LIGHT_CHANNELS 1
#define LIGHT_CH1_PIN 5
#define LIGHT_CH1_INVERSE 0
// A bit of HLW8012 - pins 6,7,8
#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT 1
#endif
#define HLW8012_SEL_PIN 6
#define HLW8012_CF1_PIN 7
#define HLW8012_CF_PIN 8
// A bit of Dallas - pin 9
#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT 1
#endif
#define DALLAS_PIN 9
// A bit of ECH1560 - pins 10,11, 12
#ifndef ECH1560_SUPPORT
#define ECH1560_SUPPORT 1
#endif
#define ECH1560_CLK_PIN 10
#define ECH1560_MISO_PIN 11
#define ECH1560_INVERTED 12
#elif defined(TRAVIS02)
// Relay provider dual
#define MANUFACTURER "TravisCI"
#define DEVICE "Virtual board 02"
// A bit of DHT - pin 1
#ifndef DHT_SUPPORT
#define DHT_SUPPORT 1
#endif
#define DHT_PIN 1
// Relay type dual - pins 2,3
#define RELAY_PROVIDER RELAY_PROVIDER_DUAL
#define RELAY1_PIN 2
#define RELAY2_PIN 3
#define RELAY1_TYPE RELAY_TYPE_NORMAL
#define RELAY2_TYPE RELAY_TYPE_NORMAL
// IR - pin 4
#define IR_SUPPORT 1
#define IR_PIN 4
#define IR_BUTTON_SET 1
#elif defined(TRAVIS03)
// Relay provider light/my92XX
#define MANUFACTURER "TravisCI"
#define DEVICE "Virtual board 03"
// MY9231 Light - pins 1,2
#define RELAY_PROVIDER RELAY_PROVIDER_LIGHT
#define LIGHT_PROVIDER LIGHT_PROVIDER_MY92XX
#define DUMMY_RELAY_COUNT 1
#define LIGHT_CHANNELS 5
#define MY92XX_MODEL MY92XX_MODEL_MY9231
#define MY92XX_CHIPS 2
#define MY92XX_DI_PIN 1
#define MY92XX_DCKI_PIN 2
#define MY92XX_COMMAND MY92XX_COMMAND_DEFAULT
#define MY92XX_MAPPING 4, 3, 5, 0, 1
#endif
// -----------------------------------------------------------------------------
// Check definitions
// -----------------------------------------------------------------------------
#if not defined(MANUFACTURER) || not defined(DEVICE)
#error "UNSUPPORTED HARDWARE!!"
#endif