mh
/
mhsw-espurna


								//------------------------------------------------------------------------------

								// Do not change this file unless you know what you are doing

								// Configuration settings are in the settings.h file

								//------------------------------------------------------------------------------


								//------------------------------------------------------------------------------

								// GENERAL

								//------------------------------------------------------------------------------


								#define ADMIN_PASS              "fibonacci" // Default password (WEB, OTA, WIFI)

								#define DEVICE_NAME             MANUFACTURER "_" DEVICE // Concatenate both to get a unique device name

								#define LOOP_DELAY_TIME         10          // Delay for this millis in the main loop [0-250]


								#define ARRAYINIT(type, name, ...) \

								    type name[] = {__VA_ARGS__};


								//------------------------------------------------------------------------------

								// TELNET

								//------------------------------------------------------------------------------


								#ifndef TELNET_SUPPORT

								#define TELNET_SUPPORT          1               // Enable telnet support by default (3.34Kb)

								#endif


								#ifndef TELNET_STA

								#define TELNET_STA              0               // By default, disallow connections via STA interface

								#endif


								#define TELNET_PORT             23              // Port to listen to telnet clients

								#define TELNET_MAX_CLIENTS      1               // Max number of concurrent telnet clients


								//------------------------------------------------------------------------------

								// DEBUG

								//------------------------------------------------------------------------------


								// Serial debug log


								#ifndef DEBUG_SERIAL_SUPPORT

								#define DEBUG_SERIAL_SUPPORT    1               // Enable serial debug log

								#endif

								#ifndef DEBUG_PORT

								#define DEBUG_PORT              Serial          // Default debugging port

								#endif


								//------------------------------------------------------------------------------


								// UDP debug log

								// To receive the message son the destination computer use nc:

								// nc -ul 8113


								#ifndef DEBUG_UDP_SUPPORT

								#define DEBUG_UDP_SUPPORT       0               // Enable UDP debug log

								#endif

								#define DEBUG_UDP_IP            IPAddress(192, 168, 1, 100)

								#define DEBUG_UDP_PORT          8113


								//------------------------------------------------------------------------------


								#ifndef DEBUG_TELNET_SUPPORT

								#define DEBUG_TELNET_SUPPORT    TELNET_SUPPORT  // Enable telnet debug log if telnet is enabled too

								#endif


								//------------------------------------------------------------------------------


								// General debug options and macros

								#define DEBUG_FORMAT_MAX_LENGTH 80

								#define DEBUG_SUPPORT           DEBUG_SERIAL_SUPPORT || DEBUG_UDP_SUPPORT || DEBUG_TELNET_SUPPORT


								#if DEBUG_SUPPORT

								    #define DEBUG_MSG(...) debugSend(__VA_ARGS__)

								    #define DEBUG_MSG_P(...) debugSend_P(__VA_ARGS__)

								#endif


								#ifndef DEBUG_MSG

								    #define DEBUG_MSG(...)

								    #define DEBUG_MSG_P(...)

								#endif


								//------------------------------------------------------------------------------

								// TERMINAL

								//------------------------------------------------------------------------------


								#ifndef TERMINAL_SUPPORT

								#define TERMINAL_SUPPORT         1               // Enable terminal commands (0.97Kb)

								#endif


								//------------------------------------------------------------------------------

								// SYSTEM CHECK

								//------------------------------------------------------------------------------


								#ifndef SYSTEM_CHECK_ENABLED

								#define SYSTEM_CHECK_ENABLED    1               // Enable crash check by default

								#endif


								#define SYSTEM_CHECK_TIME       60000           // The system is considered stable after these many millis

								#define SYSTEM_CHECK_MAX        5               // After this many crashes on boot

								                                                // the system is flagged as unstable


								//------------------------------------------------------------------------------

								// EEPROM

								//------------------------------------------------------------------------------


								#define EEPROM_SIZE             4096            // EEPROM size in bytes

								#define EEPROM_RELAY_STATUS     0               // Address for the relay status (1 byte)

								#define EEPROM_ENERGY_COUNT     1               // Address for the energy counter (4 bytes)

								#define EEPROM_CUSTOM_RESET     5               // Address for the reset reason (1 byte)

								#define EEPROM_CRASH_COUNTER    6               // Address for the crash counter (1 byte)

								#define EEPROM_DATA_END         7               // End of custom EEPROM data block


								//------------------------------------------------------------------------------

								// HEARTBEAT

								//------------------------------------------------------------------------------


								#define HEARTBEAT_INTERVAL          300000      // Interval between heartbeat messages (in ms)

								#define UPTIME_OVERFLOW             4294967295  // Uptime overflow value


								// Topics that will be reported in heartbeat

								#define HEARTBEAT_REPORT_STATUS     1

								#define HEARTBEAT_REPORT_IP         1

								#define HEARTBEAT_REPORT_MAC        1

								#define HEARTBEAT_REPORT_RSSI       1

								#define HEARTBEAT_REPORT_UPTIME     1

								#define HEARTBEAT_REPORT_DATETIME   1

								#define HEARTBEAT_REPORT_FREEHEAP   1

								#define HEARTBEAT_REPORT_VCC        1

								#define HEARTBEAT_REPORT_RELAY      1

								#define HEARTBEAT_REPORT_LIGHT      1

								#define HEARTBEAT_REPORT_HOSTNAME   1

								#define HEARTBEAT_REPORT_APP        1

								#define HEARTBEAT_REPORT_VERSION    1

								#define HEARTBEAT_REPORT_INTERVAL   0


								//------------------------------------------------------------------------------

								// RESET

								//------------------------------------------------------------------------------


								#define CUSTOM_RESET_HARDWARE   1               // Reset from hardware button

								#define CUSTOM_RESET_WEB        2               // Reset from web interface

								#define CUSTOM_RESET_TERMINAL   3               // Reset from terminal

								#define CUSTOM_RESET_MQTT       4               // Reset via MQTT

								#define CUSTOM_RESET_RPC        5               // Reset via RPC (HTTP)

								#define CUSTOM_RESET_OTA        6               // Reset after successful OTA update

								#define CUSTOM_RESET_NOFUSS     8               // Reset after successful NOFUSS update

								#define CUSTOM_RESET_UPGRADE    9               // Reset after update from web interface

								#define CUSTOM_RESET_FACTORY    10              // Factory reset from terminal


								#define CUSTOM_RESET_MAX        10


								PROGMEM const char custom_reset_hardware[] = "Hardware button";

								PROGMEM const char custom_reset_web[] = "Reboot from web interface";

								PROGMEM const char custom_reset_terminal[] = "Reboot from terminal";

								PROGMEM const char custom_reset_mqtt[] = "Reboot from MQTT";

								PROGMEM const char custom_reset_rpc[] = "Reboot from RPC";

								PROGMEM const char custom_reset_ota[] = "Reboot after successful OTA update";

								PROGMEM const char custom_reset_nofuss[] = "Reboot after successful NoFUSS update";

								PROGMEM const char custom_reset_upgrade[] = "Reboot after successful web update";

								PROGMEM const char custom_reset_factory[] = "Factory reset";

								PROGMEM const char* const custom_reset_string[] = {

								    custom_reset_hardware, custom_reset_web, custom_reset_terminal,

								    custom_reset_mqtt, custom_reset_rpc, custom_reset_ota,

								    custom_reset_nofuss, custom_reset_upgrade, custom_reset_factory

								};


								//------------------------------------------------------------------------------

								// BUTTON

								//------------------------------------------------------------------------------


								#define BUTTON_DEBOUNCE_DELAY       50          // Debounce delay (ms)

								#define BUTTON_DBLCLICK_DELAY       500         // Time in ms to wait for a second (or third...) click

								#define BUTTON_LNGCLICK_DELAY       1000        // Time in ms holding the button down to get a long click

								#define BUTTON_LNGLNGCLICK_DELAY    10000       // Time in ms holding the button down to get a long-long click


								#define BUTTON_EVENT_NONE           0

								#define BUTTON_EVENT_PRESSED        1

								#define BUTTON_EVENT_RELEASED       2

								#define BUTTON_EVENT_CLICK          2

								#define BUTTON_EVENT_DBLCLICK       3

								#define BUTTON_EVENT_LNGCLICK       4

								#define BUTTON_EVENT_LNGLNGCLICK    5


								#define BUTTON_MODE_NONE            0

								#define BUTTON_MODE_TOGGLE          1

								#define BUTTON_MODE_ON              2

								#define BUTTON_MODE_OFF             3

								#define BUTTON_MODE_AP              4

								#define BUTTON_MODE_RESET           5

								#define BUTTON_MODE_PULSE           6

								#define BUTTON_MODE_FACTORY         7


								//------------------------------------------------------------------------------

								// RELAY

								//------------------------------------------------------------------------------


								#define RELAY_MODE_OFF          0

								#define RELAY_MODE_ON           1

								#define RELAY_MODE_SAME         2

								#define RELAY_MODE_TOOGLE       3


								#define RELAY_TYPE_NORMAL       0

								#define RELAY_TYPE_INVERSE      1

								#define RELAY_TYPE_LATCHED      2


								#define RELAY_SYNC_ANY          0

								#define RELAY_SYNC_NONE_OR_ONE  1

								#define RELAY_SYNC_ONE          2

								#define RELAY_SYNC_SAME         3


								#define RELAY_PULSE_NONE        0

								#define RELAY_PULSE_OFF         1

								#define RELAY_PULSE_ON          2


								#define RELAY_PROVIDER_RELAY    0

								#define RELAY_PROVIDER_DUAL     1

								#define RELAY_PROVIDER_LIGHT    2

								#define RELAY_PROVIDER_RFBRIDGE 3


								// Pulse time in milliseconds

								#define RELAY_PULSE_TIME        1.0


								// 0 means OFF, 1 ON and 2 whatever was before

								#define RELAY_MODE         		RELAY_MODE_OFF


								// 0 means ANY, 1 zero or one and 2 one and only one

								#define RELAY_SYNC         		RELAY_SYNC_ANY


								// 0 means no pulses, 1 means normally off, 2 normally on

								#define RELAY_PULSE_MODE     	RELAY_PULSE_NONE


								// Relay requests flood protection window - in seconds

								#define RELAY_FLOOD_WINDOW      3


								// Allowed actual relay changes inside requests flood protection window

								#define RELAY_FLOOD_CHANGES     5


								// Pulse with in milliseconds for a latched relay

								#define RELAY_LATCHING_PULSE    10


								// Do not save relay state after these many milliseconds

								#define RELAY_SAVE_DELAY        1000


								//------------------------------------------------------------------------------

								// I18N

								//------------------------------------------------------------------------------


								#define TMP_CELSIUS             0

								#define TMP_FAHRENHEIT          1


								//------------------------------------------------------------------------------

								// LED

								//------------------------------------------------------------------------------


								#define LED_MODE_MQTT           0       // LED will be managed from MQTT (OFF by default)

								#define LED_MODE_WIFI           1       // LED will blink according to the WIFI status

								#define LED_MODE_FOLLOW         2       // LED will follow state of linked relay (check RELAY#_LED)

								#define LED_MODE_FOLLOW_INVERSE 3       // LED will follow the opposite state of linked relay (check RELAY#_LED)

								#define LED_MODE_FINDME         4       // LED will be ON if all relays are OFF

								#define LED_MODE_MIXED          5       // A mixed between WIFI and FINDME


								// -----------------------------------------------------------------------------

								// WIFI

								// -----------------------------------------------------------------------------


								#define WIFI_CONNECT_TIMEOUT    60000       // Connecting timeout for WIFI in ms

								#define WIFI_RECONNECT_INTERVAL 180000      // If could not connect to WIFI, retry after this time in ms

								#define WIFI_MAX_NETWORKS       5           // Max number of WIFI connection configurations

								#define WIFI_AP_MODE            AP_MODE_ALONE

								#define WIFI_SLEEP_ENABLED      1           // Enable WiFi light sleep


								// Optional hardcoded configuration (up to 2 different networks)

								//#define WIFI1_SSID              "..."

								//#define WIFI1_PASS              "..."

								//#define WIFI1_IP                "192.168.1.201"

								//#define WIFI1_GW                "192.168.1.1"

								//#define WIFI1_MASK              "255.255.255.0"

								//#define WIFI1_DNS               "8.8.8.8"

								//#define WIFI2_SSID              "..."

								//#define WIFI2_PASS              "..."


								// -----------------------------------------------------------------------------

								// WEB

								// -----------------------------------------------------------------------------


								#ifndef WEB_SUPPORT

								#define WEB_SUPPORT             1           // Enable web support (http, api, 121.65Kb)

								#endif


								#ifndef WEB_EMBEDDED

								#define WEB_EMBEDDED            1           // Build the firmware with the web interface embedded in

								#endif


								// This is not working at the moment!!

								// Requires ASYNC_TCP_SSL_ENABLED to 1 and ESP8266 Arduino Core staging version.

								#define WEB_SSL_ENABLED         0           // Use HTTPS web interface


								#define WEB_MODE_NORMAL         0

								#define WEB_MODE_PASSWORD       1


								#define WEB_USERNAME            "admin"     // HTTP username

								#define WEB_FORCE_PASS_CHANGE   1           // Force the user to change the password if default one

								#define WEB_PORT                80          // HTTP port


								// -----------------------------------------------------------------------------

								// WEBSOCKETS

								// -----------------------------------------------------------------------------


								// This will only be enabled if WEB_SUPPORT is 1 (this is the default value)


								#define WS_BUFFER_SIZE          5           // Max number of secured websocket connections

								#define WS_TIMEOUT              1800000     // Timeout for secured websocket


								// -----------------------------------------------------------------------------

								// API

								// -----------------------------------------------------------------------------


								// This will only be enabled if WEB_SUPPORT is 1 (this is the default value)


								#define API_ENABLED             0           // Do not enable API by default

								#define API_BUFFER_SIZE         15          // Size of the buffer for HTTP GET API responses

								#define API_REAL_TIME_VALUES    0           // Show filtered/median values by default (0 => median, 1 => real time)


								// -----------------------------------------------------------------------------

								// MDNS & LLMNR

								// -----------------------------------------------------------------------------


								#ifndef MDNS_SUPPORT

								#define MDNS_SUPPORT            1           // Publish services using mDNS by default (1.84Kb)

								#endif


								#ifndef LLMNR_SUPPORT

								#define LLMNR_SUPPORT           0           // Publish device using LLMNR protocol by default (1.95Kb) - requires 2.4.0

								#endif


								#ifndef NETBIOS_SUPPORT

								#define NETBIOS_SUPPORT         0           // Publish device using NetBIOS protocol by default (1.26Kb) - requires 2.4.0

								#endif


								// -----------------------------------------------------------------------------

								// SPIFFS

								// -----------------------------------------------------------------------------


								#ifndef SPIFFS_SUPPORT

								#define SPIFFS_SUPPORT           0          // Do not add support for SPIFFS by default

								#endif


								// -----------------------------------------------------------------------------

								// OTA

								// -----------------------------------------------------------------------------


								#define OTA_PORT                8266        // OTA port


								// -----------------------------------------------------------------------------

								// NOFUSS

								// -----------------------------------------------------------------------------


								#ifndef NOFUSS_SUPPORT

								#define NOFUSS_SUPPORT          0          // Do not enable support for NoFuss by default (12.65Kb)

								#endif


								#define NOFUSS_ENABLED          0           // Do not perform NoFUSS updates by default

								#define NOFUSS_SERVER           ""          // Default NoFuss Server

								#define NOFUSS_INTERVAL         3600000     // Check for updates every hour


								// -----------------------------------------------------------------------------

								// MQTT

								// -----------------------------------------------------------------------------


								#ifndef MQTT_SUPPORT

								#define MQTT_SUPPORT            1           // MQTT support (22.38Kb async, 12.48Kb sync)

								#endif


								#ifndef MQTT_USE_ASYNC

								#define MQTT_USE_ASYNC          1           // Use AysncMQTTClient (1) or PubSubClient

								#endif


								// MQTT OVER SSL

								// Using MQTT over SSL works pretty well but generates problems with the web interface.

								// It could be a good idea to use it in conjuntion with WEB_SUPPORT=0.

								// Requires ASYNC_TCP_SSL_ENABLED to 1 and ESP8266 Arduino Core staging version.

								//

								// You can use it with MQTT_USE_ASYNC=1 (AsyncMqttClient library)

								// but you might experience hiccups on the web interface, so my recommendation is:

								// WEB_SUPPORT=0

								//

								// If you use it with MQTT_USE_ASYNC=0 (PubSubClient library)

								// you will have to disable all the modules that use ESPAsyncTCP, that is:

								// ALEXA_SUPPORT=0, INFLUXDB_SUPPORT=0, TELNET_SUPPORT=0 and WEB_SUPPORT=0

								//

								// You will need the fingerprint for your MQTT server, example for CloudMQTT:

								// $ echo -n | openssl s_client -connect m11.cloudmqtt.com:24055 > cloudmqtt.pem

								// $ openssl x509 -noout -in cloudmqtt.pem -fingerprint -sha1


								#define MQTT_SSL_ENABLED        0           // By default MQTT over SSL will not be enabled

								#define MQTT_SSL_FINGERPRINT    ""          // SSL fingerprint of the server


								#define MQTT_ENABLED            0           // Do not enable MQTT connection by default

								#define MQTT_AUTOCONNECT        1           // If enabled and MDNS_SUPPORT=1 will perform an autodiscover and

								                                            // autoconnect to the first MQTT broker found if none defined

								#define MQTT_SERVER             ""          // Default MQTT broker address

								#define MQTT_USER               ""          // Default MQTT broker usename

								#define MQTT_PASS               ""          // Default MQTT broker password

								#define MQTT_PORT               1883        // MQTT broker port

								#define MQTT_TOPIC              "{identifier}"     // Default MQTT base topic

								#define MQTT_RETAIN             true        // MQTT retain flag

								#define MQTT_QOS                0           // MQTT QoS value for all messages

								#define MQTT_KEEPALIVE          30          // MQTT keepalive value


								#define MQTT_RECONNECT_DELAY_MIN    5000    // Try to reconnect in 5 seconds upon disconnection

								#define MQTT_RECONNECT_DELAY_STEP   5000    // Increase the reconnect delay in 5 seconds after each failed attempt

								#define MQTT_RECONNECT_DELAY_MAX    120000  // Set reconnect time to 2 minutes at most


								#define MQTT_SKIP_RETAINED      1           // Skip retained messages on connection

								#define MQTT_SKIP_TIME          1000        // Skip messages for 1 second anter connection


								#define MQTT_USE_JSON           0           // Group messages in a JSON body

								#define MQTT_USE_JSON_DELAY     100         // Wait this many ms before grouping messages

								#define MQTT_QUEUE_MAX_SIZE     10          // Size of the MQTT queue when MQTT_USE_JSON is enabled


								// These particles will be concatenated to the MQTT_TOPIC base to form the actual topic

								#define MQTT_TOPIC_JSON         "data"

								#define MQTT_TOPIC_ACTION       "action"

								#define MQTT_TOPIC_RELAY        "relay"

								#define MQTT_TOPIC_LED          "led"

								#define MQTT_TOPIC_BUTTON       "button"

								#define MQTT_TOPIC_IP           "ip"

								#define MQTT_TOPIC_VERSION      "version"

								#define MQTT_TOPIC_UPTIME       "uptime"

								#define MQTT_TOPIC_DATETIME     "datetime"

								#define MQTT_TOPIC_FREEHEAP     "freeheap"

								#define MQTT_TOPIC_VCC          "vcc"

								#define MQTT_TOPIC_STATUS       "status"

								#define MQTT_TOPIC_MAC          "mac"

								#define MQTT_TOPIC_RSSI         "rssi"

								#define MQTT_TOPIC_APP          "app"

								#define MQTT_TOPIC_INTERVAL     "interval"

								#define MQTT_TOPIC_HOSTNAME     "host"

								#define MQTT_TOPIC_TIME         "time"

								#define MQTT_TOPIC_ANALOG       "analog"

								#define MQTT_TOPIC_COUNTER      "counter"

								#define MQTT_TOPIC_RFOUT        "rfout"

								#define MQTT_TOPIC_RFIN         "rfin"

								#define MQTT_TOPIC_RFLEARN      "rflearn"


								// Power module

								#define MQTT_TOPIC_CURRENT          "current"

								#define MQTT_TOPIC_VOLTAGE          "voltage"

								#define MQTT_TOPIC_POWER_ACTIVE     "power"

								#define MQTT_TOPIC_POWER_APPARENT   "apparent"

								#define MQTT_TOPIC_POWER_REACTIVE   "reactive"

								#define MQTT_TOPIC_MAX_POWER        "max_power"

								#define MQTT_TOPIC_POWER_FACTOR     "factor"

								#define MQTT_TOPIC_ENERGY_DELTA     "energy_delta"

								#define MQTT_TOPIC_ENERGY_TOTAL     "energy_total"


								// Light module

								#define MQTT_TOPIC_CHANNEL      "channel"

								#define MQTT_TOPIC_COLOR        "color"     // DEPRECATED, use RGB instead

								#define MQTT_TOPIC_COLOR_RGB    "rgb"

								#define MQTT_TOPIC_COLOR_HSV    "hsv"

								#define MQTT_TOPIC_ANIM_MODE    "anim_mode"

								#define MQTT_TOPIC_ANIM_SPEED   "anim_speed"

								#define MQTT_TOPIC_BRIGHTNESS   "brightness"

								#define MQTT_TOPIC_MIRED        "mired"

								#define MQTT_TOPIC_KELVIN       "kelvin"


								#define MQTT_STATUS_ONLINE      "1"         // Value for the device ON message

								#define MQTT_STATUS_OFFLINE     "0"         // Value for the device OFF message (will)


								#define MQTT_ACTION_RESET       "reboot"    // RESET MQTT topic particle


								// Internal MQTT events (do not change)

								#define MQTT_CONNECT_EVENT      0

								#define MQTT_DISCONNECT_EVENT   1

								#define MQTT_MESSAGE_EVENT      2


								// Custom get and set postfixes

								// Use something like "/status" or "/set", with leading slash

								// Since 1.9.0 the default value is "" for getter and "/set" for setter

								#define MQTT_USE_GETTER         ""

								#define MQTT_USE_SETTER         "/set"


								// -----------------------------------------------------------------------------

								// SETTINGS

								// -----------------------------------------------------------------------------


								#ifndef SETTINGS_AUTOSAVE

								#define SETTINGS_AUTOSAVE       1           // Autosave settings o force manual commit

								#endif


								// -----------------------------------------------------------------------------

								// LIGHT

								// -----------------------------------------------------------------------------


								// Available light providers (do not change)

								#define LIGHT_PROVIDER_NONE     0

								#define LIGHT_PROVIDER_MY92XX   1 // works with MY9291 and MY9231

								#define LIGHT_PROVIDER_DIMMER   2


								// LIGHT_PROVIDER_DIMMER can have from 1 to 5 different channels.

								// They have to be defined for each device in the hardware.h file.

								// If 3 or more channels first 3 will be considered RGB.

								// Usual configurations are:

								// 1 channels => W

								// 2 channels => WW

								// 3 channels => RGB

								// 4 channels => RGBW

								// 5 channels => RGBWW


								#ifndef LIGHT_SAVE_ENABLED

								#define LIGHT_SAVE_ENABLED      1           // Light channel values saved by default after each change

								#endif


								#define LIGHT_SAVE_DELAY        5           // Persist color after 5 seconds to avoid wearing out


								#ifndef LIGHT_MAX_PWM


								#if LIGHT_PROVIDER == LIGHT_PROVIDER_MY92XX

								#define LIGHT_MAX_PWM           255

								#endif


								#if LIGHT_PROVIDER == LIGHT_PROVIDER_DIMMER

								#define LIGHT_MAX_PWM           10000        // 5000 * 200ns => 1 kHz

								#endif


								#endif // LIGHT_MAX_PWM


								#ifndef LIGHT_LIMIT_PWM

								#define LIGHT_LIMIT_PWM         LIGHT_MAX_PWM   // Limit PWM to this value (prevent 100% power)

								#endif


								#ifndef LIGHT_MAX_VALUE

								#define LIGHT_MAX_VALUE         255         // Maximum light value

								#endif


								#define LIGHT_MAX_BRIGHTNESS    255         // Maximun brightness value

								#define LIGHT_STEP              32          // Step size

								#define LIGHT_USE_COLOR         1           // Use 3 first channels as RGB

								#define LIGHT_USE_WHITE         0           // Use white channel whenever RGB have the same value

								#define LIGHT_USE_GAMMA         0           // Use gamma correction for color channels

								#define LIGHT_USE_CSS           1           // Use CSS style to report colors (1=> "#FF0000", 0=> "255,0,0")

								#define LIGHT_USE_RGB           0           // Use RGB color selector (1=> RGB, 0=> HSV)


								#define LIGHT_USE_TRANSITIONS   1           // Transitions between colors

								#define LIGHT_TRANSITION_STEP   10          // Time in millis between each transtion step

								#define LIGHT_TRANSITION_STEPS  50          // Number of steps to acomplish transition


								// -----------------------------------------------------------------------------

								// POWER METERING

								// -----------------------------------------------------------------------------


								// Available power-metering providers (do not change this)

								#define POWER_PROVIDER_NONE             0x00

								#define POWER_PROVIDER_EMON_ANALOG      0x10

								#define POWER_PROVIDER_EMON_ADC121      0x11

								#define POWER_PROVIDER_HLW8012          0x20

								#define POWER_PROVIDER_V9261F           0x30

								#define POWER_PROVIDER_ECH1560          0x40


								// Available magnitudes (do not change this)

								#define POWER_MAGNITUDE_CURRENT         1

								#define POWER_MAGNITUDE_VOLTAGE         2

								#define POWER_MAGNITUDE_ACTIVE          4

								#define POWER_MAGNITUDE_APPARENT        8

								#define POWER_MAGNITUDE_REACTIVE        16

								#define POWER_MAGNITUDE_POWER_FACTOR    32

								#define POWER_MAGNITUDE_ALL             63


								// No power provider defined (do not change this)

								#ifndef POWER_PROVIDER

								#define POWER_PROVIDER                  POWER_PROVIDER_NONE

								#endif


								// Identify available magnitudes (do not change this)

								#if (POWER_PROVIDER == POWER_PROVIDER_HLW8012) || (POWER_PROVIDER == POWER_PROVIDER_V9261F)

								#define POWER_HAS_ACTIVE                1

								#else

								#define POWER_HAS_ACTIVE                0

								#endif


								#if (POWER_PROVIDER == POWER_PROVIDER_HLW8012)

								#define POWER_HAS_ENERGY                1

								#else

								#define POWER_HAS_ENERGY                0

								#endif


								#define POWER_VOLTAGE                   230     // Default voltage

								#define POWER_MIN_READ_INTERVAL         2000    // Minimum read interval

								#define POWER_READ_INTERVAL             6000    // Default reading interval (6 seconds)

								#define POWER_REPORT_INTERVAL           60000   // Default report interval (1 minute)

								#define POWER_CURRENT_DECIMALS          2       // Decimals for current values

								#define POWER_VOLTAGE_DECIMALS          0       // Decimals for voltage values

								#define POWER_POWER_DECIMALS            0       // Decimals for power values

								#define POWER_ENERGY_DECIMALS           3       // Decimals for energy values

								#define POWER_ENERGY_DECIMALS_KWH       6       // Decimals for energy values

								#define POWER_ENERGY_FACTOR             1       // Watt * seconds == Joule (Ws == J)

								#define POWER_ENERGY_FACTOR_KWH         (1. / 1000. / 3600.) // kWh


								#if POWER_PROVIDER == POWER_PROVIDER_EMON_ANALOG

								    #define EMON_CURRENT_RATIO          30      // Current ratio in the clamp (30V/1A)

								    #define EMON_SAMPLES                1000    // Number of samples to get for each reading

									#define EMON_ADC_BITS               10      // ADC depth

									#define EMON_REFERENCE_VOLTAGE      1.0     // Reference voltage of the ADC

								    #define EMON_CURRENT_OFFSET         0.25    // Current offset (error)

								    #undef ADC_VCC_ENABLED

								    #define ADC_VCC_ENABLED             0       // Disable internal battery measurement

								#endif


								#if POWER_PROVIDER == POWER_PROVIDER_EMON_ADC121

								    #define EMON_CURRENT_RATIO          30      // Current ratio in the clamp (30V/1A)

								    #define EMON_SAMPLES                1000    // Number of samples to get for each reading

								    #define EMON_ADC_BITS               12      // ADC depth

									#define EMON_REFERENCE_VOLTAGE      3.3     // Reference voltage of the ADC

								    #define EMON_CURRENT_OFFSET         0.10    // Current offset (error)

								    #define ADC121_I2C_ADDRESS          0x50    // I2C address of the ADC121

								    #undef I2C_SUPPORT

								    #define I2C_SUPPORT                 1       // Enabled I2C support

								#endif


								#if POWER_PROVIDER == POWER_PROVIDER_HLW8012

								    #define HLW8012_USE_INTERRUPTS      1       // Use interrupts to trap HLW8012 signals

								    #define HLW8012_SEL_CURRENT         HIGH    // SEL pin to HIGH to measure current

								    #define HLW8012_CURRENT_R           0.001   // Current resistor

								    #define HLW8012_VOLTAGE_R_UP        ( 5 * 470000 )  // Upstream voltage resistor

								    #define HLW8012_VOLTAGE_R_DOWN      ( 1000 )        // Downstream voltage resistor

								#endif


								#if POWER_PROVIDER == POWER_PROVIDER_V9261F


								    #ifndef V9261F_PIN

								    #define V9261F_PIN                  2       // TX pin from the V9261F

								    #endif

								    #ifndef V9261F_PIN_INVERSE

								    #define V9261F_PIN_INVERSE          1       // Signal is inverted

								    #endif


								    #define V9261F_SYNC_INTERVAL        600     // Sync signal length (ms)

								    #define V9261F_BAUDRATE             4800    // UART baudrate


								    // Default ratios

								    #define V9261F_CURRENT_FACTOR       79371434.0

								    #define V9261F_VOLTAGE_FACTOR       4160651.0

								    #define V9261F_POWER_FACTOR         153699.0

								    #define V9261F_RPOWER_FACTOR        V9261F_CURRENT_FACTOR


								#endif


								#if POWER_PROVIDER == POWER_PROVIDER_ECH1560


								    #ifndef ECH1560_CLK_PIN

								    #define ECH1560_CLK_PIN             4       // Default CLK pin

								    #endif

								    #ifndef ECH1560_MISO_PIN

								    #define ECH1560_MISO_PIN            5       // Default MISO pin

								    #endif

								    #ifndef ECH1560_INVERTED

								    #define ECH1560_INVERTED            0       // Power signal is inverted

								    #endif


								#endif


								// -----------------------------------------------------------------------------

								// I2C

								// -----------------------------------------------------------------------------


								#ifndef I2C_SUPPORT

								#define I2C_SUPPORT             1           // I2C enabled (1.98Kb)

								#endif


								#define I2C_USE_BRZO            0           // Use brzo_i2c library or standard Wire


								#ifndef I2C_SDA_PIN

								#define I2C_SDA_PIN             SDA         // SDA GPIO (Sonoff => 4)

								#endif


								#ifndef I2C_SCL_PIN

								#define I2C_SCL_PIN             SCL         // SCL GPIO (Sonoff => 14)

								#endif


								#define I2C_CLOCK_STRETCH_TIME  200         // BRZO clock stretch time

								#define I2C_SCL_FREQUENCY       1000        // BRZO SCL frequency

								#define I2C_CLEAR_BUS           0           // Clear I2C bus at boot


								// -----------------------------------------------------------------------------

								// DOMOTICZ

								// -----------------------------------------------------------------------------


								#ifndef DOMOTICZ_SUPPORT

								#define DOMOTICZ_SUPPORT        MQTT_SUPPORT    // Build with domoticz (if MQTT) support (1.72Kb)

								#endif


								#define DOMOTICZ_ENABLED        0               // Disable domoticz by default

								#define DOMOTICZ_IN_TOPIC       "domoticz/in"   // Default subscription topic

								#define DOMOTICZ_OUT_TOPIC      "domoticz/out"  // Default publication topic

								#define DOMOTICZ_SKIP_TIME      2               // Avoid recursion skipping messages to same IDX within 2 seconds


								// -----------------------------------------------------------------------------

								// HOME ASSISTANT

								// -----------------------------------------------------------------------------


								#ifndef HOMEASSISTANT_SUPPORT

								#define HOMEASSISTANT_SUPPORT   MQTT_SUPPORT    // Build with home assistant support (if MQTT, 1.64Kb)

								#endif


								#define HOMEASSISTANT_ENABLED   0               // Integration not enabled by default

								#define HOMEASSISTANT_PREFIX    "homeassistant" // Default MQTT prefix


								// -----------------------------------------------------------------------------

								// INFLUXDB

								// -----------------------------------------------------------------------------


								#ifndef INFLUXDB_SUPPORT

								#define INFLUXDB_SUPPORT        0               // Enable InfluxDB support by default (4.38Kb)

								#endif


								#define INFLUXDB_ENABLED        0               // InfluxDB disabled by default

								#define INFLUXDB_HOST           ""              // Default server

								#define INFLUXDB_PORT           8086            // Default InfluxDB port

								#define INFLUXDB_DATABASE       ""              // Default database

								#define INFLUXDB_USERNAME       ""              // Default username

								#define INFLUXDB_PASSWORD       ""              // Default password


								// -----------------------------------------------------------------------------

								// NTP

								// -----------------------------------------------------------------------------


								#ifndef NTP_SUPPORT

								#define NTP_SUPPORT             1               // Build with NTP support by default (6.78Kb)

								#endif


								#define NTP_SERVER              "pool.ntp.org"  // Default NTP server

								#define NTP_TIME_OFFSET         1               // Default timezone offset (GMT+1)

								#define NTP_DAY_LIGHT           true            // Enable daylight time saving by default

								#define NTP_UPDATE_INTERVAL     1800            // NTP check every 30 minutes


								// -----------------------------------------------------------------------------

								// FAUXMO

								// -----------------------------------------------------------------------------


								// This setting defines whether Alexa support should be built into the firmware

								#ifndef ALEXA_SUPPORT

								#define ALEXA_SUPPORT           1               // Enable Alexa support by default (9.5Kb)

								#endif


								// This is default value for the alexaEnabled setting that defines whether

								// this device should be discoberable and respond to Alexa commands.

								// Both ALEXA_SUPPORT and alexaEnabled should be 1 for Alexa support to work.

								#define ALEXA_ENABLED           1


								// -----------------------------------------------------------------------------

								// RFBRIDGE

								// -----------------------------------------------------------------------------


								#define RF_SEND_TIMES           4               // How many times to send the message

								#define RF_SEND_DELAY           250             // Interval between sendings in ms

								#define RF_RECEIVE_DELAY        500             // Interval between recieving in ms (avoid debouncing)


								// -----------------------------------------------------------------------------

								// SENSORS

								// -----------------------------------------------------------------------------


								#define SENSOR_READ_INTERVAL            6000            // Read data from sensors every 6 seconds

								#define SENSOR_REPORT_EVERY             10              // Report every this many readings

								#define SENSOR_USE_INDEX                0               // Use the index in topic (i.e. temperature/0)

								                                                        // even if just one sensor (0 for backwards compatibility)


								#define SENSOR_TEMPERATURE_DECIMALS     1

								#define SENSOR_HUMIDITY_DECIMALS        0

								#define SENSOR_PRESSURE_DECIMALS        2

								#define SENSOR_ANALOG_DECIMALS          0

								#define SENSOR_EVENTS_DECIMALS          0

								#define SENSOR_CURRENT_DECIMALS         3

								#define SENSOR_VOLTAGE_DECIMALS         0

								#define SENSOR_POWER_DECIMALS           0

								#define SENSOR_POWER_FACTOR_DECIMALS    0

								#define SENSOR_ENERGY_DECIMALS          0


								#define SENSOR_UNKNOWN_TOPIC            "unknown"

								#define SENSOR_TEMPERATURE_TOPIC        "temperature"

								#define SENSOR_HUMIDITY_TOPIC           "humidity"

								#define SENSOR_PRESSURE_TOPIC           "pressure"

								#define SENSOR_CURRENT_TOPIC            "current"

								#define SENSOR_VOLTAGE_TOPIC            "voltage"

								#define SENSOR_ACTIVE_POWER_TOPIC       "power"

								#define SENSOR_APPARENT_POWER_TOPIC     "apparent"

								#define SENSOR_REACTIVE_POWER_TOPIC     "reactive"

								#define SENSOR_POWER_FACTOR_TOPIC       "factor"

								#define SENSOR_ENERGY_TOPIC             "energy"

								#define SENSOR_ENERGY_DELTA_TOPIC       "energy_delta"

								#define SENSOR_ANALOG_TOPIC             "analog"

								#define SENSOR_EVENTS_TOPIC             "events"


								#define SENSOR_TEMPERATURE_UNITS        TMP_CELSIUS     // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)

								#define SENSOR_TEMPERATURE_CORRECTION   0.0             // Offset correction


								// -----------------------------------------------------------------------------

								// IR

								// -----------------------------------------------------------------------------


								#ifndef IR_SUPPORT

								#define IR_SUPPORT              0               // Do not build with IR support by default (10.25Kb)

								#endif


								#ifndef IR_PIN

								#define IR_PIN                  4               // IR LED

								#endif


								// 24 Buttons Set of the IR Remote

								#ifndef IR_BUTTON_SET

								#define IR_BUTTON_SET           1               // IR button set to use (see below)

								#endif


								// IR Button modes

								#define IR_BUTTON_MODE_NONE         0

								#define IR_BUTTON_MODE_RGB          1

								#define IR_BUTTON_MODE_HSV          2

								#define IR_BUTTON_MODE_BRIGHTER     3

								#define IR_BUTTON_MODE_STATE        4

								#define IR_BUTTON_MODE_EFFECT       5


								#define LIGHT_EFFECT_SOLID          0

								#define LIGHT_EFFECT_FLASH          1

								#define LIGHT_EFFECT_STROBE         2

								#define LIGHT_EFFECT_FADE           3

								#define LIGHT_EFFECT_SMOOTH         4


								//Remote Buttons SET 1 (for the original Remote shipped with the controller)

								#if IR_SUPPORT

								#if IR_BUTTON_SET == 1


								    #define IR_BUTTON_COUNT 24


								    const unsigned long IR_BUTTON[IR_BUTTON_COUNT][3] PROGMEM = {


								        { 0xFF906F, IR_BUTTON_MODE_BRIGHTER, 1 },

								        { 0xFFB847, IR_BUTTON_MODE_BRIGHTER, 0 },

								        { 0xFFF807, IR_BUTTON_MODE_STATE, 0 },

								        { 0xFFB04F, IR_BUTTON_MODE_STATE, 1 },


								        { 0xFF9867, IR_BUTTON_MODE_RGB, 0xFF0000 },

								        { 0xFFD827, IR_BUTTON_MODE_RGB, 0x00FF00 },

								        { 0xFF8877, IR_BUTTON_MODE_RGB, 0x0000FF },

								        { 0xFFA857, IR_BUTTON_MODE_RGB, 0xFFFFFF },


								        { 0xFFE817, IR_BUTTON_MODE_RGB, 0xD13A01 },

								        { 0xFF48B7, IR_BUTTON_MODE_RGB, 0x00E644 },

								        { 0xFF6897, IR_BUTTON_MODE_RGB, 0x0040A7 },

								        { 0xFFB24D, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_FLASH },


								        { 0xFF02FD, IR_BUTTON_MODE_RGB, 0xE96F2A },

								        { 0xFF32CD, IR_BUTTON_MODE_RGB, 0x00BEBF },

								        { 0xFF20DF, IR_BUTTON_MODE_RGB, 0x56406F },

								        { 0xFF00FF, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_STROBE },


								        { 0xFF50AF, IR_BUTTON_MODE_RGB, 0xEE9819 },

								        { 0xFF7887, IR_BUTTON_MODE_RGB, 0x00799A },

								        { 0xFF708F, IR_BUTTON_MODE_RGB, 0x944E80 },

								        { 0xFF58A7, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_FADE },


								        { 0xFF38C7, IR_BUTTON_MODE_RGB, 0xFFFF00 },

								        { 0xFF28D7, IR_BUTTON_MODE_RGB, 0x0060A1 },

								        { 0xFFF00F, IR_BUTTON_MODE_RGB, 0xEF45AD },

								        { 0xFF30CF, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_SMOOTH }


								    };


								#endif


								//Remote Buttons SET 2 (another identical IR Remote shipped with another controller)

								#if IR_BUTTON_SET == 2


								    #define IR_BUTTON_COUNT 24


								    const unsigned long IR_BUTTON[IR_BUTTON_COUNT][3] PROGMEM = {


								        { 0xFF00FF, IR_BUTTON_MODE_BRIGHTER, 1 },

								        { 0xFF807F, IR_BUTTON_MODE_BRIGHTER, 0 },

								        { 0xFF40BF, IR_BUTTON_MODE_STATE, 0 },

								        { 0xFFC03F, IR_BUTTON_MODE_STATE, 1 },


								        { 0xFF20DF, IR_BUTTON_MODE_RGB, 0xFF0000 },

								        { 0xFFA05F, IR_BUTTON_MODE_RGB, 0x00FF00 },

								        { 0xFF609F, IR_BUTTON_MODE_RGB, 0x0000FF },

								        { 0xFFE01F, IR_BUTTON_MODE_RGB, 0xFFFFFF },


								        { 0xFF10EF, IR_BUTTON_MODE_RGB, 0xD13A01 },

								        { 0xFF906F, IR_BUTTON_MODE_RGB, 0x00E644 },

								        { 0xFF50AF, IR_BUTTON_MODE_RGB, 0x0040A7 },

								        { 0xFFD02F, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_FLASH },


								        { 0xFF30CF, IR_BUTTON_MODE_RGB, 0xE96F2A },

								        { 0xFFB04F, IR_BUTTON_MODE_RGB, 0x00BEBF },

								        { 0xFF708F, IR_BUTTON_MODE_RGB, 0x56406F },

								        { 0xFFF00F, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_STROBE },


								        { 0xFF08F7, IR_BUTTON_MODE_RGB, 0xEE9819 },

								        { 0xFF8877, IR_BUTTON_MODE_RGB, 0x00799A },

								        { 0xFF48B7, IR_BUTTON_MODE_RGB, 0x944E80 },

								        { 0xFFC837, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_FADE },


								        { 0xFF28D7, IR_BUTTON_MODE_RGB, 0xFFFF00 },

								        { 0xFFA857, IR_BUTTON_MODE_RGB, 0x0060A1 },

								        { 0xFF6897, IR_BUTTON_MODE_RGB, 0xEF45AD },

								        { 0xFFE817, IR_BUTTON_MODE_EFFECT, LIGHT_EFFECT_SMOOTH }


								    };


								#endif

								#endif // IR_SUPPORT


								//--------------------------------------------------------------------------------

								// Custom RF module

								// Check http://tinkerman.cat/adding-rf-to-a-non-rf-itead-sonoff/

								// Enable support by passing RF_SUPPORT=1 build flag

								//--------------------------------------------------------------------------------


								#ifndef RF_SUPPORT

								#define RF_SUPPORT                  0

								#endif


								#ifndef RF_PIN

								#define RF_PIN                      14

								#endif


								#define RF_CHANNEL                  31

								#define RF_DEVICE                   1