mhsw-espurna/CHANGELOG.md

ESPurna change log

The format is based on Keep a Changelog and this project adheres to Semantic Versioning.

[1.7.1] 2017-03-28

Fix

• Issue #113. Fix restoring color from EEPROM upon reboot
• Issue #113. Fix bug in API handlers

[1.7.0] 2017-03-27

Added

• Web interface embedded in firmware image by default
• Upload firmware image from web interface
• Added API entry point to change light color
• Added generic analog sensor. Thanks to Francesco Boscarino
• Report RSSI value in debug console and MQTT status messages
• Added support for Magic Home LED Controller
• Added support for ESPurna-H Board (based on HLW8012)
• Added forward compatible code for v2.0

Changed

• Added ellipsis (...) in debug messages longer than 80 characters
• Changed topic constants in code
• Prevent the SDK from saving WiFi configuration to flash

Fix

• Issue #113. Fix light bulb state to OFF in library prevented the bulb from turning on
• Issue #58. Added code to handle spurious readings
• Fix bug in HLW8012 calibration current parameter casting to int instead of float
• Issue #115. Removed local declaration of _mqttForward variable. Thanks to Paweł Fiedor
• Fix MQTT will topic. Thanks to Asbjorn Tronhus

[1.6.9] 2017-03-12

Added

• Two stage read for DS18B20 devices. Thanks to Izik Dubnov.
• Option to report the relay status via MQTT periodically
• Terminal commands to change relay status an light color
• Added debug via UDP (disabled by default)
• Moved debug strings to PROGMEM. ~1.5KByes memory freed
• Avoid broadcasting websocket messages if no clients connected

Fix

• Fixing use after free bug that leads to corrupted auth credentials. Thanks to David Guillen

[1.6.8] 2017-03-01

Added

• Issue #85. Heartbeat reports now free heap, uptime and VCC every 5 minutes

Changed

• Wait two minutes instead of one in AP mode before trying to reconnect to the router
• Issue #92. Debug log enabled by default in Arduino IDE
• Issue #91. Using AsyncMqttClient as default MQTT client again

Fix

• Report data from all sensors via websocket even if no MQTT connection
• Issue #92. Fix unknown reference in Arduino IDE
• Split data.h contents into 1k lines, otherwise Arduino IDE chokes on them
• Discard empty MQTT topic while subscribing

[1.6.7] 2017-02-25

Added

• Support for OpenLight / AI-Light by AI-Thinker based on MY9291 LED driver
• Issue #87. Factory reset when physical button pressed for >10 seconds

[1.6.6] 2017-02-23

Fix

• Issue #82. Fix critical bug on Sonoff Dual

[1.6.5] 2017-02-22

Added

• Option to backup and restore settings from the web interface
• Footer in the web interface

Changed

• Using PubSubClient as MQTT client by default (please read the documentation)
• Double & long clicks do nothing except for the first defined button

Fix

• Issue #79. Fix bug in WiFi led notification & MQTT connectivity (using PubSubClient)
• Issue #73. Fix bug when building without Domoticz support
• Fix Gulp tasks dependencies

[1.6.4] 2017-02-20

Added

• Option to embed the web interface in the firmware, disabled by default
• Change relay status with a GET request (browser friendly)
• Support for PROGMEM debug messages (only wifi module has been changed)
• Option to disable mDNS, enabled by default
• Show current web server port in debug log
• Issue #75. Link relays to LEDs
• Issue #76. Using http://espurna.local when in AP mode

Changed

• Images and favicon is now embedded in the HTML
• Authentication challenge only in /auth request. All static contents are un-authenticated
• HTTP response code when out of websocket slots changed from 423 to 429

Fix

• Memory leak in MQTT connection method
• Wait 60 seconds before retrying to connect when in AP mode
• Issue #24 & #74. Update ESPAsyncTCP and ESPAsyncWebServer to latest GIT version that supports MSS defragmenting
• Issue #73. Fixes for windows machines

Removed

• Captive portal removed, mDNS resolution for AP mode too

[1.6.3] 2017-02-15

Added

• Issue #69. Temperature unit configuration from the web interface
• Issue #55. WebServer port configurable from the web interface, defaults to 80
• Expand network configuration when adding a new network

Changed

• Merged web contents except images in a single compressed file for reliability
• Update support for Itead Motor Clockwise/Anticlockwise board
• Scan for strongest network only if more than 1 network configured

Fix

• Issue #71. Added default values for netmask and DNS in web configuration
• Fixed Itead 1CH self-locking/inching board definition
• Fixed PlatformIO environments for ESP8285 boards (4CH and Touch)

[1.6.2] 2017-02-10

Fix

• Check if there is an MQTT broker defined before the MQTT_MAX_TRIES check

[1.6.1] 2017-02-10

Added

• Added support for Jorge Garcia's Wifi+Relay Board Kit
• Reporting current and energy incrementals to a separate counters in Domoticz (thanks to Toni Arte)
• Force WiFi reconnect after MQTT_MAX_TRIES fails trying to connect to MQTT broker

[1.6.0] 2017-02-05

Added

• Added support for toggle switches
• Allow reset the board via an MQTT message
• Allow reset the board via an RPC (HTTP) message
• Added support for ADC121 I2C for current monitoring (Check http://tinkerman.cat/power-monitoring-sonoff-th-adc121/)
• Reporting voltage to Domoticz (only HLW8012)
• Map button events to actions (toggle relay, AP mode, reset, pulse mode)

Changed

• Reporting energy incrementals (Domoticz, MQTT)

Removed

• Removed current monitor bypass when relay is OFF
• Removed energy API entry point

[1.5.4] 2017-02-03

Fixed

• Issue #50. Fix type bug in window variable when calculating energy for HLW8012 devices (Sonoff POW)

[1.5.3] 2017-02-02

Fixed

• Issue #50 and #54. Fixed domoticz MQTT message format

Added

• Energy calculation and aggregation. API entry points and MQTT messages.

[1.5.2] 2017-01-29

Fixed

• Fix bug in emon topic payload

[1.5.1] 2017-01-28

Added

• OpenEnergyMonitor WiFi MQTT Relay / Thermostat support (thanks to Denis French)

Fixed

• NTP connection refresh upon wifi connection
• Filesystem image build using local gulp installation

[1.5.0] 2017-01-21

Added

• Pulse mode. Allows to define a pulse time after which the relay will switch back
• API entry points for sensor data (power, current, voltage, temperature and humidity)
• Export sensor data to Domoticz (power, current, voltage, temperature and humidity)
• Configurable (in code) mapping between buttons and relays
• MQTT messages for button events
• Added support for Itead Studio 1CH inching/self locking smart switch board
• Added support for Jan Goedeke Wifi Relay boards (both NC and NO versions)
• Notify OTA updates to websocket clients, automatically reload page
• Support for pulse mode notification LED and button
• Revert relay state mode on boot (thanks to Minh Phuong Ly)

Fixed

• MQTT will topic
• Crash with HLW812 interrupts while trying to create a WIFI connection
• Issue #20 Better inline documentation for Alexa and Domoticz default settings
• Issue #39 Fixed autoconnect issue with static IP (fixed in JustWifi library)
• Issue #41 Added password requirements to initial password change page

Changed

• Changed LED pattern for WIFI notifications (shorter pulses)

[1.4.4] 2017-01-13

Added

• Adding current, voltage, apparent and reactive power reports to Sonoff POW (Web & MQTT)

Fixed

• Issue #35 Fixed frequent MQTT connection drops after WIFI reconnect
• Defer wifi disconnection from web interface to allow request to return

Changed

• Move all Arduino IDE configuration values to their own file
• Using latest HLW8012 library in interrupt mode

[1.4.3] 2017-01-11

Fixed

• Issue #6 Using forked Time library to prevent conflict with Arduino Core for ESP8266 time.h file in windows machines

[1.4.2] 2017-01-09

Added

• Support for inverse logic relays

Fixed

• Issue #31. Fixed error in relay identification from MQTT messages

[1.4.1] 2017-01-05

Added

• Alexa support by default on all devices
• Added support for Wemos D1 Mini board with official Relay Shield

Fixed

• Multi-packet websocket frames

[1.4.0] 2016-12-31

Added

• Domoticz support via MQTT (https://www.domoticz.com/wiki/MQTT)
• Support for static IP connections

Fixed

• Issue #16. Enforce minimum password strength in web interface

Changed

• Using default client_id provided by AsyncMqttClient
• Allow up to 5 different WIFI networks

Removed

• File system version file

[1.3.1] 2016-12-31

Fixed

• data_dir fix for PlatformIO

[1.3.0] 2016-12-30

Changed

• Arduino IDE support (changes in the folder structure and documentation)

[1.2.0] 2016-12-27

Added

• Force password changing if it's the default one
• Added Last-Modified header to static contents
• Added DNS captive portal for AP mode
• Added support for Sonoff 4CH
• Added support for WorkChoice ecoPlug (ECOPLUG). Thanks to David Myers
• Added support for Sonoff SV
• Added support for Sonoff Touch
• Comment out hardware selection in hardware.h if using Arduino IDE
• Added support for MQTT get/set suffixes (/status, /set, ...)
• Added support for LED notifications via MQTT
• Added EEPROM check commands to terminal interface

Changed

• Using unreleased AsyncMqttClient with stability improvements
• Better decoupling between MQTT and relays/websockets
• Skipping retained MQTT messages (configurable)

Fixed

• Issue #11 Compile error when building sonoff-dual-debug
• Issue #14 MQTT Connection with Username an Password not working
• Issue #17 Moved static variable 'pending' to class variable

[1.1.0] 2016-12-06

Added

• Added support for DS18B20 temperature sensor. Thanks to Francesco Boscarino
• Added reset command from console
• Added support for multirelay boards like Sonoff DUAL or Electrodragon ESP Relay Board

Changed

• Not using espressif8266_stage in default environment
• Relay MQTT topics
• API entry points

Removed

• Old non protected API

[1.0.3] 2016-11-29

Added

• WeMo emulation through the fauxmoESP library (control your switch from Alexa!)
• REST API for relay management
• Better dependency definitions in platformio.ini
• Option to define inverse logic to on-board LED
• Built data folder included in repo

Changed

• Using non-interrupt driven mode for HLW8012
• Better documentation
• Small changes to web interface
• Same admin password for web, OTA and WIFI AP mode

Fixed

• Prevent fauxmoESP to be compiled by default

Removed

• Removed ESPurna board to its own repo

[1.0.1] 2016-11-13

Added

• Basic authentication and CSRF to websocket requests

[1.0.0] 2016-11-13

Added

• Using ESPAsyncWebServer (for web & websockets) and AsyncMqttClient

[0.9.9] 2016-11-12

Added

• Preliminary support for Sonoff POW
• Replace AJAX requests with websockets
• Using sprites for images
• Hostname can be changed
• Added initial relay state mode
• Reconnect and reset buttons on web interface

Changed

• Changed long click to reset and double click to AP mode
• Using officially supported platformio.ini file by default

Fixed

• Removed unnecessary memory inefficient code
• Temprary fix for Adafruit DHT library (see https://github.com/adafruit/DHT-sensor-library/issues/62)

[0.9.8] 2016-10-06

Added

• Using PureCMS for the web interface
• Using gulp to build the filesystem files
• Using Embedis for configuration

Changed

• Updated JustWifi library
• Web interface changes
• Using custom platformio.ini file
• Loads of changes in modules
• Added DEBUG_MSG

Fixed

• Clean gulp builder script

[0.9.7] 2016-08-28

Changed

• Moving wifi management to library (JustWifi)
• Split code into modules

[0.9.6] 2016-08-12

Added

• Added heartbeat, version and fsversion MQTT messages

Changed

• GZip 3rd party contents

[0.9.5] 2016-07-31

• Initial stable version