You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
383 lines
13 KiB
383 lines
13 KiB
// -----------------------------------------------------------------------------
|
|
// SENSORS
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#define SENSOR_DEBUG 0 // Debug sensors
|
|
|
|
#define SENSOR_READ_INTERVAL 6000 // Read data from sensors every 6 seconds
|
|
#define SENSOR_REPORT_EVERY 10 // Report every this many readings
|
|
#define SENSOR_USE_INDEX 0 // Use the index in topic (i.e. temperature/0)
|
|
// even if just one sensor (0 for backwards compatibility)
|
|
|
|
#ifndef SENSOR_TEMPERATURE_UNITS
|
|
#define SENSOR_TEMPERATURE_UNITS TMP_CELSIUS // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)
|
|
#endif
|
|
|
|
#ifndef SENSOR_TEMPERATURE_CORRECTION
|
|
#define SENSOR_TEMPERATURE_CORRECTION 0.0 // Offset correction
|
|
#endif
|
|
|
|
#ifndef TEMPERATURE_MIN_CHANGE
|
|
#define TEMPERATURE_MIN_CHANGE 0.0 // Minimum temperature change to report
|
|
#endif
|
|
|
|
#ifndef HUMIDITY_MIN_CHANGE
|
|
#define HUMIDITY_MIN_CHANGE 0 // Minimum humidity change to report
|
|
#endif
|
|
|
|
#define SENSOR_TEMPERATURE_DECIMALS 1
|
|
#define SENSOR_HUMIDITY_DECIMALS 0
|
|
#define SENSOR_PRESSURE_DECIMALS 2
|
|
#define SENSOR_ANALOG_DECIMALS 0
|
|
#define SENSOR_EVENTS_DECIMALS 0
|
|
#define SENSOR_CURRENT_DECIMALS 3
|
|
#define SENSOR_VOLTAGE_DECIMALS 0
|
|
#define SENSOR_POWER_DECIMALS 0
|
|
#define SENSOR_POWER_FACTOR_DECIMALS 0
|
|
#define SENSOR_ENERGY_DECIMALS 0
|
|
#define SENSOR_PM1dot0_DECIMALS 0
|
|
#define SENSOR_PM2dot5_DECIMALS 0
|
|
#define SENSOR_PM10_DECIMALS 0
|
|
#define SENSOR_CO2_DECIMALS 0
|
|
|
|
#define SENSOR_UNKNOWN_TOPIC "unknown"
|
|
#define SENSOR_TEMPERATURE_TOPIC "temperature"
|
|
#define SENSOR_HUMIDITY_TOPIC "humidity"
|
|
#define SENSOR_PRESSURE_TOPIC "pressure"
|
|
#define SENSOR_CURRENT_TOPIC "current"
|
|
#define SENSOR_VOLTAGE_TOPIC "voltage"
|
|
#define SENSOR_ACTIVE_POWER_TOPIC "power"
|
|
#define SENSOR_APPARENT_POWER_TOPIC "apparent"
|
|
#define SENSOR_REACTIVE_POWER_TOPIC "reactive"
|
|
#define SENSOR_POWER_FACTOR_TOPIC "factor"
|
|
#define SENSOR_ENERGY_TOPIC "energy"
|
|
#define SENSOR_ENERGY_DELTA_TOPIC "energy_delta"
|
|
#define SENSOR_PM1dot0_TOPIC "pm1dot0"
|
|
#define SENSOR_PM2dot5_TOPIC "pm2dot5"
|
|
#define SENSOR_PM10_TOPIC "pm10"
|
|
#define SENSOR_ANALOG_TOPIC "analog"
|
|
#define SENSOR_DIGITAL_TOPIC "digital"
|
|
#define SENSOR_EVENTS_TOPIC "events"
|
|
#define SENSOR_CO2_TOPIC "co2"
|
|
|
|
#define HUMIDITY_NORMAL 0
|
|
#define HUMIDITY_COMFORTABLE 1
|
|
#define HUMIDITY_DRY 2
|
|
#define HUMIDITY_WET 3
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Analog sensor
|
|
// Enable support by passing ANALOG_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef ANALOG_SUPPORT
|
|
#define ANALOG_SUPPORT 0
|
|
#endif
|
|
|
|
#if ANALOG_SUPPORT
|
|
#undef ADC_VCC_ENABLED
|
|
#define ADC_VCC_ENABLED 0
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// BME280/BMP280
|
|
// Enable support by passing BMX280_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef BMX280_SUPPORT
|
|
#define BMX280_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef BMX280_ADDRESS
|
|
#define BMX280_ADDRESS 0x00 // 0x00 means auto
|
|
#endif
|
|
|
|
#define BMX280_MODE 1 // 1 for forced mode, 3 for normal mode
|
|
#define BMX280_TEMPERATURE 1 // Oversampling for temperature (set to 0 to disable magnitude)
|
|
#define BMX280_HUMIDITY 1 // Oversampling for humidity (set to 0 to disable magnitude, only for BME280)
|
|
#define BMX280_PRESSURE 1 // Oversampling for pressure (set to 0 to disable magnitude)
|
|
|
|
#if BMX280_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Dallas OneWire temperature sensors
|
|
// Enable support by passing DALLAS_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef DALLAS_SUPPORT
|
|
#define DALLAS_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef DALLAS_PIN
|
|
#define DALLAS_PIN 13
|
|
#endif
|
|
|
|
#ifndef DALLAS_PULLUP
|
|
#define DALLAS_PULLUP 1
|
|
#endif
|
|
|
|
#define DALLAS_RESOLUTION 9 // Not used atm
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// DHTXX temperature/humidity sensor
|
|
// Enable support by passing DHT_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef DHT_SUPPORT
|
|
#define DHT_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef DHT_PIN
|
|
#define DHT_PIN 13
|
|
#endif
|
|
|
|
#ifndef DHT_TYPE
|
|
#define DHT_TYPE DHT22
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Digital sensor
|
|
// Enable support by passing DIGITAL_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef DIGITAL_SUPPORT
|
|
#define DIGITAL_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef DIGITAL_PIN
|
|
#define DIGITAL_PIN 2
|
|
#endif
|
|
|
|
#ifndef DIGITAL_PIN_MODE
|
|
#define DIGITAL_PIN_MODE INPUT_PULLUP
|
|
#endif
|
|
|
|
#ifndef DIGITAL_DEFAULT_STATE
|
|
#define DIGITAL_DEFAULT_STATE 1
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Energy Monitor general settings
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#define EMON_MAX_SAMPLES 1000 // Max number of samples to get
|
|
#define EMON_MAX_TIME 250 // Max time in ms to sample
|
|
#define EMON_FILTER_SPEED 512 // Mobile average filter speed
|
|
#define EMON_MAINS_VOLTAGE 230 // Mains voltage
|
|
#define EMON_REFERENCE_VOLTAGE 3.3 // Reference voltage of the ADC
|
|
#define EMON_CURRENT_RATIO 30 // Current ratio in the clamp (30V/1A)
|
|
#define EMON_REPORT_CURRENT 0 // Report current
|
|
#define EMON_REPORT_POWER 1 // Report power
|
|
#define EMON_REPORT_ENERGY 1 // Report energy
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Energy Monitor based on ADC121
|
|
// Enable support by passing EMON_ADC121_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef EMON_ADC121_SUPPORT
|
|
#define EMON_ADC121_SUPPORT 0 // Do not build support by default
|
|
#endif
|
|
|
|
#define EMON_ADC121_I2C_ADDRESS 0x00 // 0x00 means auto
|
|
|
|
#if EMON_ADC121_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Energy Monitor based on ADS1X15
|
|
// Enable support by passing EMON_ADS1X15_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef EMON_ADS1X15_SUPPORT
|
|
#define EMON_ADS1X15_SUPPORT 0 // Do not build support by default
|
|
#endif
|
|
|
|
#define EMON_ADS1X15_I2C_ADDRESS 0x00 // 0x00 means auto
|
|
#define EMON_ADS1X15_TYPE ADS1X15_CHIP_ADS1115
|
|
#define EMON_ADS1X15_GAIN ADS1X15_REG_CONFIG_PGA_4_096V
|
|
#define EMON_ADS1X15_MASK 0x0F // A0=1 A1=2 A2=4 A4=8
|
|
|
|
#if EMON_ADS1X15_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Energy Monitor based on interval analog GPIO
|
|
// Enable support by passing EMON_ANALOG_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef EMON_ANALOG_SUPPORT
|
|
#define EMON_ANALOG_SUPPORT 0 // Do not build support by default
|
|
#endif
|
|
|
|
#if EMON_ANALOG_SUPPORT
|
|
#undef ADC_VCC_ENABLED
|
|
#define ADC_VCC_ENABLED 0
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Counter sensor
|
|
// Enable support by passing EVENTS_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef EVENTS_SUPPORT
|
|
#define EVENTS_SUPPORT 0 // Do not build with counter support by default
|
|
#endif
|
|
|
|
#ifndef EVENTS_PIN
|
|
#define EVENTS_PIN 2 // GPIO to monitor
|
|
#endif
|
|
|
|
#ifndef EVENTS_PIN_MODE
|
|
#define EVENTS_PIN_MODE INPUT // INPUT, INPUT_PULLUP
|
|
#endif
|
|
|
|
#ifndef EVENTS_INTERRUPT_MODE
|
|
#define EVENTS_INTERRUPT_MODE RISING // RISING, FALLING, BOTH
|
|
#endif
|
|
|
|
#define EVENTS_DEBOUNCE 50 // Do not register events within less than 10 millis
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// MHZ19 CO2 sensor
|
|
// Enable support by passing MHZ19_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef MHZ19_SUPPORT
|
|
#define MHZ19_SUPPORT 0
|
|
#endif
|
|
|
|
#define MHZ19_RX_PIN 13
|
|
#define MHZ19_TX_PIN 15
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Particle Monitor based on Plantower PMSX003
|
|
// Enable support by passing PMSX003_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef PMSX003_SUPPORT
|
|
#define PMSX003_SUPPORT 0
|
|
#endif
|
|
|
|
#define PMS_RX_PIN 13
|
|
#define PMS_TX_PIN 15
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// SI7021 temperature & humidity sensor
|
|
// Enable support by passing SI7021_SUPPORT=1 build flag
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef SI7021_SUPPORT
|
|
#define SI7021_SUPPORT 0
|
|
#endif
|
|
|
|
#ifndef SI7021_ADDRESS
|
|
#define SI7021_ADDRESS 0x00 // 0x00 means auto
|
|
#endif
|
|
|
|
#if SI7021_SUPPORT
|
|
#undef I2C_SUPPORT
|
|
#define I2C_SUPPORT 1
|
|
#endif
|
|
|
|
// -----------------------------------------------------------------------------
|
|
// I2C
|
|
// -----------------------------------------------------------------------------
|
|
|
|
#ifndef I2C_SUPPORT
|
|
#define I2C_SUPPORT 0 // I2C enabled (1.98Kb)
|
|
#endif
|
|
|
|
#define I2C_USE_BRZO 0 // Use brzo_i2c library or standard Wire
|
|
|
|
#ifndef I2C_SDA_PIN
|
|
#define I2C_SDA_PIN SDA // SDA GPIO (Sonoff => 4)
|
|
#endif
|
|
|
|
#ifndef I2C_SCL_PIN
|
|
#define I2C_SCL_PIN SCL // SCL GPIO (Sonoff => 14)
|
|
#endif
|
|
|
|
#define I2C_CLOCK_STRETCH_TIME 200 // BRZO clock stretch time
|
|
#define I2C_SCL_FREQUENCY 1000 // BRZO SCL frequency
|
|
#define I2C_CLEAR_BUS 0 // Clear I2C bus at boot
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Internal power monitor
|
|
// Enable support by passing ADC_VCC_ENABLED=1 build flag
|
|
// Do not enable this if using the analog GPIO for any other thing
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#ifndef ADC_VCC_ENABLED
|
|
#define ADC_VCC_ENABLED 1
|
|
#endif
|
|
|
|
#if ADC_VCC_ENABLED
|
|
ADC_MODE(ADC_VCC);
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------------------
|
|
// Class loading
|
|
//--------------------------------------------------------------------------------
|
|
|
|
#include "sensors/BaseSensor.h"
|
|
|
|
#if ANALOG_SUPPORT
|
|
#include "sensors/AnalogSensor.h"
|
|
#endif
|
|
|
|
#if BMX280_SUPPORT
|
|
#include <SparkFunBME280.h>
|
|
#include "sensors/BMX280Sensor.h"
|
|
#endif
|
|
|
|
#if DALLAS_SUPPORT
|
|
#include <OneWire.h>
|
|
#include "sensors/DallasSensor.h"
|
|
#endif
|
|
|
|
#if DHT_SUPPORT
|
|
#include "sensors/DHTSensor.h"
|
|
#endif
|
|
|
|
#if DIGITAL_SUPPORT
|
|
#include "sensors/DigitalSensor.h"
|
|
#endif
|
|
|
|
#if EMON_ADC121_SUPPORT
|
|
#include "sensors/EmonADC121Sensor.h"
|
|
#endif
|
|
|
|
#if EMON_ADS1X15_SUPPORT
|
|
#include "sensors/EmonADS1X15Sensor.h"
|
|
#endif
|
|
|
|
#if EMON_ANALOG_SUPPORT
|
|
#include "sensors/EmonAnalogSensor.h"
|
|
#endif
|
|
|
|
#if EVENTS_SUPPORT
|
|
#include "sensors/EventSensor.h"
|
|
#endif
|
|
|
|
#if MHZ19_SUPPORT
|
|
#include <SoftwareSerial.h>
|
|
#include "sensors/MHZ19Sensor.h"
|
|
#endif
|
|
|
|
#if PMSX003_SUPPORT
|
|
#include <SoftwareSerial.h>
|
|
#include <PMS.h>
|
|
#include "sensors/PMSX003Sensor.h"
|
|
#endif
|
|
|
|
#if SI7021_SUPPORT
|
|
#include "sensors/SI7021Sensor.h"
|
|
#endif
|