mh
/
mhsw-espurna


								//------------------------------------------------------------------------------

								// GENERAL

								//------------------------------------------------------------------------------


								#define SERIAL_BAUDRATE         115200

								#define HOSTNAME                DEVICE

								#define BUFFER_SIZE             1024

								#define HEARTBEAT_INTERVAL      300000


								//--------------------------------------------------------------------------------

								// EEPROM

								//--------------------------------------------------------------------------------


								#define EEPROM_RELAY_STATUS     0

								#define EEPROM_POWER_COUNT      1


								//--------------------------------------------------------------------------------

								// RELAY

								//--------------------------------------------------------------------------------


								#define RELAY_MODE_OFF          0

								#define RELAY_MODE_ON           1

								#define RELAY_MODE_SAME         2

								#define RELAY_MODE_TOOGLE       3


								#define RELAY_SYNC_ANY          0

								#define RELAY_SYNC_NONE_OR_ONE  1

								#define RELAY_SYNC_ONE          2

								#define RELAY_SYNC_SAME         3


								#define RELAY_PULSE_NONE        0

								#define RELAY_PULSE_OFF         1

								#define RELAY_PULSE_ON          2


								// Pulse time in seconds

								#define RELAY_PULSE_TIME        1


								// 0 means OFF, 1 ON and 2 whatever was before

								#define RELAY_MODE         		RELAY_MODE_OFF


								// 0 means ANY, 1 zero or one and 2 one and only one

								#define RELAY_SYNC         		RELAY_SYNC_ANY


								// 0 means no pulses, 1 means normally off, 2 normally on

								#define RELAY_PULSE_MODE     	RELAY_PULSE_NONE


								//--------------------------------------------------------------------------------

								// LED

								//--------------------------------------------------------------------------------


								// All defined LEDs in the board can be managed through MQTT

								// except the first one when LED_AUTO is set to 1.

								// If LED_AUTO is set to 1 the board will use first defined LED to show wifi status.

								#define LED_AUTO                1


								// -----------------------------------------------------------------------------

								// WIFI & WEB

								// -----------------------------------------------------------------------------


								#define WIFI_RECONNECT_INTERVAL 300000

								#define WIFI_MAX_NETWORKS       5

								#define ADMIN_PASS              "fibonacci"

								#define HTTP_USERNAME           "admin"

								#define WS_BUFFER_SIZE          5

								#define WS_TIMEOUT              1800000

								#define DNS_PORT                53


								// -----------------------------------------------------------------------------

								// OTA & NOFUSS

								// -----------------------------------------------------------------------------


								#define OTA_PORT                8266

								#define NOFUSS_SERVER           "http://192.168.1.100"

								#define NOFUSS_INTERVAL         3600000


								// -----------------------------------------------------------------------------

								// MQTT

								// -----------------------------------------------------------------------------


								#define MQTT_SERVER             "192.168.1.100"

								#define MQTT_PORT               1883

								#define MQTT_TOPIC              "/test/switch/{identifier}"

								#define MQTT_RETAIN             true

								#define MQTT_QOS                0

								#define MQTT_KEEPALIVE          30

								#define MQTT_RECONNECT_DELAY    10000

								#define MQTT_SKIP_RETAINED      1

								#define MQTT_SKIP_TIME          1000

								#define MQTT_RELAY_TOPIC        "/relay"

								#define MQTT_LED_TOPIC          "/led"

								#define MQTT_BUTTON_TOPIC       "/button"

								#define MQTT_IP_TOPIC           "/ip"

								#define MQTT_VERSION_TOPIC      "/version"

								#define MQTT_HEARTBEAT_TOPIC    "/status"


								#define MQTT_CONNECT_EVENT      0

								#define MQTT_DISCONNECT_EVENT   1

								#define MQTT_MESSAGE_EVENT      2


								// Custom get and set postfixes

								// Use something like "/status" or "/set", with leading slash

								#define MQTT_USE_GETTER         ""

								#define MQTT_USE_SETTER         ""


								// -----------------------------------------------------------------------------

								// I2C

								// -----------------------------------------------------------------------------


								#define ENABLE_I2C              1

								#define I2C_SDA_PIN             4

								#define I2C_SCL_PIN             14

								#define I2C_CLOCK_STRETCH_TIME  200

								#define I2C_SCL_FREQUENCY       1000


								// -----------------------------------------------------------------------------

								// DOMOTICZ

								// -----------------------------------------------------------------------------


								#ifndef ENABLE_DOMOTICZ

								    #define ENABLE_DOMOTICZ     1

								#endif

								#define DOMOTICZ_IN_TOPIC       "domoticz/in"

								#define DOMOTICZ_OUT_TOPIC      "domoticz/out"


								// -----------------------------------------------------------------------------

								// NTP

								// -----------------------------------------------------------------------------


								#define NTP_SERVER              "pool.ntp.org"

								#define NTP_TIME_OFFSET         1

								#define NTP_DAY_LIGHT           true

								#define NTP_UPDATE_INTERVAL     1800


								// -----------------------------------------------------------------------------

								// FAUXMO

								// -----------------------------------------------------------------------------


								// This setting defines whether Alexa support should be built into the firmware

								#ifndef ENABLE_FAUXMO

								    #define ENABLE_FAUXMO       1

								#endif


								// This is default value for the fauxmoEnabled setting that defines whether

								// this device should be discoberable and respond to Alexa commands.

								// Both ENABLE_FAUXMO and fauxmoEnabled should be 1 for Alexa support to work.

								#define FAUXMO_ENABLED          1