qmk_firmware/keyboards/handwired/tractyl_manuform/5x6_right/f411/config.h

/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
Copyright 2015 Jack Humbert

This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.

This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with this program.  If not, see <http://www.gnu.org/licenses/>.
*/

#pragma once

#define PRODUCT Tractyl Manuform(5x6) BlackPill

// wiring of each half
#define MATRIX_COL_PINS \
    { A15, B3, B4, B5, B6, B7 }
#define MATRIX_ROW_PINS \
    { B12, B13, B14, B15, A8, A9 }

#define DIODE_DIRECTION     COL2ROW

#define USB_VBUS_PIN        B10
#define SPLIT_HAND_PIN      C14  // high = left, low = right

// WS2812 RGB LED strip input and number of LEDs
#define RGB_DI_PIN          A1
#define WS2812_PWM_DRIVER   PWMD5  // default: PWMD2
#define WS2812_PWM_CHANNEL  2      // default: 2
#define WS2812_PWM_PAL_MODE 2      // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2
//#define WS2812_PWM_COMPLEMENTARY_OUTPUT // Define for a complementary timer output (TIMx_CHyN); omit for a normal timer output (TIMx_CHy).
#define WS2812_DMA_STREAM   STM32_DMA1_STREAM0  // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
#define WS2812_DMA_CHANNEL  6                   // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.

#define RGBLED_NUM          20
#define RGBLIGHT_SPLIT
#define RGBLED_SPLIT \
    { 10, 10 }

#define DEBUG_LED_PIN     C13

#define AUDIO_PIN         A0
#define AUDIO_PWM_DRIVER  PWMD5
#define AUDIO_PWM_CHANNEL 1
#define AUDIO_STATE_TIMER GPTD4

/* serial.c configuration for split keyboard */
#define SERIAL_USART_FULL_DUPLEX  // Enable full duplex operation mode.
#define SERIAL_USART_TX_PIN      A2
#define SERIAL_USART_RX_PIN      A3
#define SERIAL_USART_DRIVER      SD2
#define SERIAL_USART_TX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
#define SERIAL_USART_RX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
#define SERIAL_USART_TIMEOUT     100  // USART driver timeout. default 100
#undef SOFT_SERIAL_PIN

// #define EE_HANDS

#define I2C_DRIVER        I2CD1
#define I2C1_SCL_BANK     GPIOB
#define I2C1_SDA_BANK     GPIOB
#define I2C1_SCL          8
#define I2C1_SDA          9
#define I2C1_SCL_PAL_MODE 4
#define I2C1_SDA_PAL_MODE 4
#define I2C1_CLOCK_SPEED  400000

#define ENCODERS_PAD_A \
    { B1 }
#define ENCODERS_PAD_B \
    { B2 }

#define SPI_DRIVER                           SPID1
#define SPI_SCK_PIN                          A5
#define SPI_SCK_PAL_MODE                     5
#define SPI_MOSI_PIN                         A7
#define SPI_MOSI_PAL_MODE                    5
#define SPI_MISO_PIN                         A6
#define SPI_MISO_PAL_MODE                    5

#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN A4
// #define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR    64
// #define EXTERNAL_EEPROM_BYTE_COUNT           8196
// #define EXTERNAL_EEPROM_PAGE_SIZE            32
// #define EXTERNAL_EEPROM_ADDRESS_SIZE         2
#define DEBUG_EEPROM_OUTPUT

#define PMW_CS_PIN  B0
#define SPI_MODE    0
#define SPI_DIVISOR 64