|
|
- #----------------------------------------------------------------------------
- # On command line:
- #
- # make all = Make software.
- #
- # make clean = Clean out built project files.
- #
- # make coff = Convert ELF to AVR COFF.
- #
- # make extcoff = Convert ELF to AVR Extended COFF.
- #
- # make program = Download the hex file to the device.
- # Please customize your programmer settings(PROGRAM_CMD)
- #
- # make teensy = Download the hex file to the device, using teensy_loader_cli.
- # (must have teensy_loader_cli installed).
- #
- # make dfu = Download the hex file to the device, using dfu-programmer (must
- # have dfu-programmer installed).
- #
- # make flip = Download the hex file to the device, using Atmel FLIP (must
- # have Atmel FLIP installed).
- #
- # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
- # (must have dfu-programmer installed).
- #
- # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
- # (must have Atmel FLIP installed).
- #
- # make debug = Start either simulavr or avarice as specified for debugging,
- # with avr-gdb or avr-insight as the front end for debugging.
- #
- # make filename.s = Just compile filename.c into the assembler code only.
- #
- # make filename.i = Create a preprocessed source file for use in submitting
- # bug reports to the GCC project.
- #
- # To rebuild project do "make clean" then "make all".
- #----------------------------------------------------------------------------
-
- # MCU name
- #MCU = at90usb1287
- MCU = atmega32u4
-
- # Processor frequency.
- # This will define a symbol, F_CPU, in all source code files equal to the
- # processor frequency in Hz. You can then use this symbol in your source code to
- # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
- # automatically to create a 32-bit value in your source code.
- #
- # This will be an integer division of F_USB below, as it is sourced by
- # F_USB after it has run through any CPU prescalers. Note that this value
- # does not *change* the processor frequency - it should merely be updated to
- # reflect the processor speed set externally so that the code can use accurate
- # software delays.
- F_CPU = 16000000
-
-
- #
- # LUFA specific
- #
- # Target architecture (see library "Board Types" documentation).
- ARCH = AVR8
-
- # Input clock frequency.
- # This will define a symbol, F_USB, in all source code files equal to the
- # input clock frequency (before any prescaling is performed) in Hz. This value may
- # differ from F_CPU if prescaling is used on the latter, and is required as the
- # raw input clock is fed directly to the PLL sections of the AVR for high speed
- # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
- # at the end, this will be done automatically to create a 32-bit value in your
- # source code.
- #
- # If no clock division is performed on the input clock inside the AVR (via the
- # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
- F_USB = $(F_CPU)
-
- # Interrupt driven control endpoint task(+60)
- OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
- # Boot Section Size in *bytes*
- # Teensy halfKay 512
- # Teensy++ halfKay 1024
- # Atmel DFU loader 4096
- # LUFA bootloader 4096
- # USBaspLoader 2048
- OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
- # Build Options
- # comment out to disable the options.
- #
- BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
- MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
- EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
- # CONSOLE_ENABLE = yes # Console for debug(+400)
- # COMMAND_ENABLE = yes # Commands for debug and configuration
- KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key
- # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
- # SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
- NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
- # BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
- # MIDI_ENABLE = YES # MIDI controls
- # UNICODE_ENABLE = YES # Unicode
- # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
- RGBLIGHT_ENABLE = yes # Enable RGB Underglow
-
- ifndef QUANTUM_DIR
- include ../../../../Makefile
- endif
-
|
