- /*
- * Copyright 2017 skully <skullydazed@gmail.com>
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- */
-
- #pragma once
- #include "config_common.h"
-
- /* Address for jumping to bootloader on STM32 chips. */
- /* It is chip dependent, the correct number can be looked up here:
- * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
- */
- #define STM32_BOOTLOADER_ADDRESS 0x1FFFD800
-
- /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
- // #define DEBOUNCE 6
-
- /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
- //#define LOCKING_SUPPORT_ENABLE
- /* Locking resynchronize hack */
- //#define LOCKING_RESYNC_ENABLE
-
- /*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
- //#define FORCE_NKRO
-
- /*
- * Feature disable options
- * These options are also useful to firmware size reduction.
- */
-
- /* disable debug print */
- //#define NO_DEBUG
-
- /* disable print */
- //#define NO_PRINT
-
- /* disable action features */
- //#define NO_ACTION_LAYER
- //#define NO_ACTION_TAPPING
- //#define NO_ACTION_ONESHOT
- //#define NO_ACTION_MACRO
- //#define NO_ACTION_FUNCTION
-
- /*
- * MIDI options
- */
-
- /* enable basic MIDI features:
- - MIDI notes can be sent when in Music mode is on
- */
- //#define MIDI_BASIC
-
- /* enable advanced MIDI features:
- - MIDI notes can be added to the keymap
- - Octave shift and transpose
- - Virtual sustain, portamento, and modulation wheel
- - etc.
- */
- //#define MIDI_ADVANCED
-
- /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
- //#define MIDI_TONE_KEYCODE_OCTAVES 1
-
- /* Backlight configuration
- */
- #define BACKLIGHT_LEVELS 10
-
- // This is a 7-bit address, that gets left-shifted and bit 0
- // set to 0 for write, 1 for read (as per I2C protocol)
- // The address will vary depending on your wiring:
- // 0b1110100 AD <-> GND
- // 0b1110111 AD <-> VCC
- // 0b1110101 AD <-> SCL
- // 0b1110110 AD <-> SDA
- #define LED_DRIVER_ADDR_1 0b1110100
- #define I2C1_SCL 8
- #define I2C1_SDA 9
-
- #define LED_DRIVER_COUNT 1
- #define LED_DRIVER_LED_COUNT 71
-
- #define AUDIO_PIN A5
- #define AUDIO_PIN_ALT A4
- #define AUDIO_PIN_ALT_AS_NEGATIVE
|