Added a layer for WOW to my Atreus62.pull/1197/head
@ -0,0 +1,3 @@ | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../../Makefile | |||
endif |
@ -0,0 +1 @@ | |||
#include "atreus50.h" |
@ -0,0 +1,18 @@ | |||
#ifndef ATREUS50_H | |||
#define ATREUS50_H | |||
#include "quantum.h" | |||
#define KEYMAP( \ | |||
K000, K001, K002, K003, K004, K005, K007, K008, K009, K010, K011, K012, \ | |||
K100, K101, K102, K103, K104, K105, K107, K108, K109, K110, K111, K112, \ | |||
K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, \ | |||
K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312 \ | |||
) { \ | |||
{ K000, K001, K002, K003, K004, K005, KC_NO, K007, K008, K009, K010, K011, K012 }, \ | |||
{ K100, K101, K102, K103, K104, K105, KC_NO, K107, K108, K109, K110, K111, K112 }, \ | |||
{ K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212 }, \ | |||
{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312 } \ | |||
} | |||
#endif |
@ -0,0 +1,58 @@ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xFEED | |||
#define PRODUCT_ID 0x6060 | |||
#define DEVICE_VER 0x0001 | |||
#define MANUFACTURER qmkbuilder | |||
#define PRODUCT Atreus50 | |||
#define DESCRIPTION Keyboard | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 4 | |||
#define MATRIX_COLS 13 | |||
/* key matrix pins */ | |||
#define MATRIX_ROW_PINS { F4, F5, F6, F7 } | |||
#define MATRIX_COL_PINS { D3, D2, D1, D0, D4, C6, D7, E6, B4, B5, B6, B2, B3 } | |||
#define UNUSED_PINS | |||
/* COL2ROW or ROW2COL */ | |||
#define DIODE_DIRECTION COL2ROW | |||
/* number of backlight levels */ | |||
#ifdef BACKLIGHT_PIN | |||
#define BACKLIGHT_LEVELS 3 | |||
#endif | |||
/* Set 0 if debouncing isn't needed */ | |||
#define DEBOUNCING_DELAY 5 | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
/* key combination for command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
/* prevent stuck modifiers */ | |||
#define PREVENT_STUCK_MODIFIERS | |||
#ifdef RGB_DI_PIN | |||
#define RGBLIGHT_ANIMATIONS | |||
#define RGBLED_NUM 0 | |||
#define RGBLIGHT_HUE_STEP 8 | |||
#define RGBLIGHT_SAT_STEP 8 | |||
#define RGBLIGHT_VAL_STEP 8 | |||
#endif | |||
#endif |
@ -0,0 +1,21 @@ | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |||
MIDI_ENABLE = no # MIDI controls | |||
AUDIO_ENABLE = no # Audio output on port C6 | |||
UNICODE_ENABLE = no # Unicode | |||
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
ifndef QUANTUM_DIR | |||
include ../../../../Makefile | |||
endif |
@ -0,0 +1,128 @@ | |||
// This is the canonical layout file for the Quantum project. If you want to add another keyboard, | |||
// this is the style you want to emulate. | |||
#include "atreus50.h" | |||
#include "action_layer.h" | |||
#include "eeconfig.h" | |||
extern keymap_config_t keymap_config; | |||
// Each layer gets a name for readability, which is then used in the keymap matrix below. | |||
// The underscores don't mean anything - you can have a layer called STUFF or any other name. | |||
// Layer names don't all need to be of the same length, obviously, and you can also skip them | |||
// entirely and just use numbers. | |||
#define _DVORAK 0 | |||
#define _QWERTY 1 | |||
#define _COLEMAK 2 | |||
#define _LOWER 3 | |||
#define _RAISE 4 | |||
#define _ADJUST 16 | |||
enum planck_keycodes { | |||
DVORAK = SAFE_RANGE, | |||
QWERTY, | |||
COLEMAK, | |||
LOWER, | |||
RAISE, | |||
BACKLIT | |||
}; | |||
// Fillers to make layering more clear | |||
#define _______ KC_TRNS | |||
#define XXXXXXX KC_NO | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
[_DVORAK] = { /* dvorak */ | |||
{ KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, _______, KC_F, KC_G, KC_C, KC_R, KC_L, KC_SLSH }, | |||
{ KC_ESC, KC_A, KC_O, KC_E, KC_U, KC_I, _______, KC_D, KC_H, KC_T, KC_N, KC_S, KC_MINS }, | |||
{ KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_ENT, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_RSFT }, | |||
{ KC_LCTL, KC_LALT, KC_LEFT, KC_RGHT, LOWER, KC_BSPC, KC_LGUI, KC_SPC, RAISE, KC_UP, KC_DOWN, KC_RGUI, KC_RCTL } | |||
}, | |||
[_QWERTY] = { /* qwerty */ | |||
{ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, _______, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL }, | |||
{ KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, _______, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT }, | |||
{ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_ENT, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT }, | |||
{ KC_LCTL, KC_LALT, KC_LEFT, KC_RGHT, LOWER, KC_BSPC, KC_LGUI, KC_SPC, RAISE, KC_UP, KC_DOWN, KC_RGUI, KC_RCTL } | |||
}, | |||
[_COLEMAK] = { /* colemak */ | |||
{ KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, _______, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_DEL }, | |||
{ KC_ESC, KC_A, KC_R, KC_S, KC_T, KC_D, _______, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT }, | |||
{ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_ENT, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT }, | |||
{ KC_LCTL, KC_LALT, KC_LEFT, KC_RGHT, LOWER, KC_BSPC, KC_LGUI, KC_SPC, RAISE, KC_UP, KC_DOWN, KC_RGUI, KC_RCTL} | |||
}, | |||
[_LOWER] = { | |||
{ KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, _______, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______ }, | |||
{ KC_CAPS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, _______, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE }, | |||
{ _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, _______, KC_F12, KC_MUTE, KC_VOLD, KC_VOLU, _______, _______ }, | |||
{ _______, _______, KC_HOME, KC_END, _______, KC_DEL, _______, KC_INS, _______, KC_PGUP, KC_PGDN, _______, _______ } | |||
}, | |||
[_RAISE] = { | |||
{ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, _______, KC_6, KC_7, KC_8, KC_9, KC_0, _______ }, | |||
{ KC_CAPS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, _______, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS }, | |||
{ _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, _______, KC_F12, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______ }, | |||
{ _______, _______, KC_HOME, KC_END, _______, KC_DEL, _______, KC_INS, _______, KC_PGUP, KC_PGDN, _______, _______ } | |||
}, | |||
[_ADJUST] = { | |||
{ KC_F11, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, _______, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F12 }, | |||
{ _______, RESET, _______, _______, _______, _______, _______, _______, QWERTY, COLEMAK, DVORAK, _______, _______ }, | |||
{ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ }, | |||
{ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ } | |||
}, | |||
}; | |||
const uint16_t PROGMEM fn_actions[] = { | |||
}; | |||
void persistant_default_layer_set(uint16_t default_layer) { | |||
eeconfig_update_default_layer(default_layer); | |||
default_layer_set(default_layer); | |||
} | |||
bool process_record_user(uint16_t keycode, keyrecord_t *record) { | |||
switch (keycode) { | |||
case QWERTY: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_QWERTY); | |||
} | |||
return false; | |||
break; | |||
case COLEMAK: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_COLEMAK); | |||
} | |||
return false; | |||
break; | |||
case DVORAK: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_DVORAK); | |||
} | |||
return false; | |||
break; | |||
case LOWER: | |||
if (record->event.pressed) { | |||
layer_on(_LOWER); | |||
update_tri_layer(_LOWER, _RAISE, _ADJUST); | |||
} else { | |||
layer_off(_LOWER); | |||
update_tri_layer(_LOWER, _RAISE, _ADJUST); | |||
} | |||
return false; | |||
break; | |||
case RAISE: | |||
if (record->event.pressed) { | |||
layer_on(_RAISE); | |||
update_tri_layer(_LOWER, _RAISE, _ADJUST); | |||
} else { | |||
layer_off(_RAISE); | |||
update_tri_layer(_LOWER, _RAISE, _ADJUST); | |||
} | |||
return false; | |||
break; | |||
} | |||
return true; | |||
}; |
@ -0,0 +1,56 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= no # Commands for debug and configuration | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality | |||
AUDIO_ENABLE ?= no | |||
RGBLIGHT_ENABLE ?= no |