@ -1,56 +0,0 @@ | |||
# Target file name (without extension). | |||
TARGET = hbk | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# keyboard dependent files | |||
SRC = main.c \ | |||
keymap.c \ | |||
matrix.c \ | |||
led.c | |||
CONFIG_H = config.h | |||
# MCU name, you MUST set this to match the board you are using | |||
# type "make clean" after changing this, so all files will be rebuilt | |||
#MCU = at90usb162 # Teensy 1.0 | |||
MCU = atmega32u4 # Teensy 2.0 | |||
#MCU = at90usb646 # Teensy++ 1.0 | |||
#MCU = at90usb1286 # Teensy++ 2.0 | |||
# Processor frequency. | |||
# Normally the first thing your program should do is set the clock prescaler, | |||
# so your program will run at the correct speed. You should also set this | |||
# variable to same clock speed. The _delay_ms() macro uses this, and many | |||
# examples use this variable to calculate timings. Do not add a "UL" here. | |||
F_CPU = 16000000 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
MOUSEKEY_ENABLE = yes # Mouse keys | |||
#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
#NKRO_ENABLE = yes # USB Nkey Rollover | |||
#---------------- Programming Options -------------------------- | |||
#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex | |||
PROGRAM_CMD = /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) erase && \ | |||
/opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) flash $(TARGET).hex && \ | |||
/opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) start | |||
include $(TOP_DIR)/protocol/pjrc.mk | |||
include $(TOP_DIR)/protocol.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |
@ -0,0 +1 @@ | |||
Makefile.lufa |
@ -0,0 +1,119 @@ | |||
#---------------------------------------------------------------------------- | |||
# On command line: | |||
# | |||
# make all = Make software. | |||
# | |||
# make clean = Clean out built project files. | |||
# | |||
# make coff = Convert ELF to AVR COFF. | |||
# | |||
# make extcoff = Convert ELF to AVR Extended COFF. | |||
# | |||
# make program = Download the hex file to the device. | |||
# Please customize your programmer settings(PROGRAM_CMD) | |||
# | |||
# make teensy = Download the hex file to the device, using teensy_loader_cli. | |||
# (must have teensy_loader_cli installed). | |||
# | |||
# make dfu = Download the hex file to the device, using dfu-programmer (must | |||
# have dfu-programmer installed). | |||
# | |||
# make flip = Download the hex file to the device, using Atmel FLIP (must | |||
# have Atmel FLIP installed). | |||
# | |||
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer | |||
# (must have dfu-programmer installed). | |||
# | |||
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP | |||
# (must have Atmel FLIP installed). | |||
# | |||
# make debug = Start either simulavr or avarice as specified for debugging, | |||
# with avr-gdb or avr-insight as the front end for debugging. | |||
# | |||
# make filename.s = Just compile filename.c into the assembler code only. | |||
# | |||
# make filename.i = Create a preprocessed source file for use in submitting | |||
# bug reports to the GCC project. | |||
# | |||
# To rebuild project do "make clean" then "make all". | |||
#---------------------------------------------------------------------------- | |||
# Target file name (without extension). | |||
TARGET = hbkb_lufa | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# List C source files here. (C dependencies are automatically generated.) | |||
SRC += keymap.c \ | |||
matrix.c \ | |||
led.c | |||
CONFIG_H = config.h | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
MOUSEKEY_ENABLE = yes # Mouse keys | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
#NKRO_ENABLE = yes # USB Nkey Rollover | |||
#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support | |||
# Boot Section Size in bytes | |||
# Teensy halfKay 512 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
OPT_DEFS += -DBOOT_SIZE=4096 | |||
# Search Path | |||
VPATH += $(TARGET_DIR) | |||
VPATH += $(TOP_DIR) | |||
include $(TOP_DIR)/protocol/lufa.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |
@ -0,0 +1,56 @@ | |||
# Target file name (without extension). | |||
TARGET = hbkb | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# keyboard dependent files | |||
SRC = main.c \ | |||
keymap.c \ | |||
matrix.c \ | |||
led.c | |||
CONFIG_H = config.h | |||
# MCU name, you MUST set this to match the board you are using | |||
# type "make clean" after changing this, so all files will be rebuilt | |||
#MCU = at90usb162 # Teensy 1.0 | |||
MCU = atmega32u4 # Teensy 2.0 | |||
#MCU = at90usb646 # Teensy++ 1.0 | |||
#MCU = at90usb1286 # Teensy++ 2.0 | |||
# Processor frequency. | |||
# Normally the first thing your program should do is set the clock prescaler, | |||
# so your program will run at the correct speed. You should also set this | |||
# variable to same clock speed. The _delay_ms() macro uses this, and many | |||
# examples use this variable to calculate timings. Do not add a "UL" here. | |||
F_CPU = 16000000 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
MOUSEKEY_ENABLE = yes # Mouse keys | |||
#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
#NKRO_ENABLE = yes # USB Nkey Rollover | |||
#---------------- Programming Options -------------------------- | |||
#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex | |||
PROGRAM_CMD = /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) erase && \ | |||
/opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) flash $(TARGET).hex && \ | |||
/opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) start | |||
include $(TOP_DIR)/protocol/pjrc.mk | |||
include $(TOP_DIR)/protocol.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |
@ -0,0 +1,119 @@ | |||
#---------------------------------------------------------------------------- | |||
# On command line: | |||
# | |||
# make all = Make software. | |||
# | |||
# make clean = Clean out built project files. | |||
# | |||
# make coff = Convert ELF to AVR COFF. | |||
# | |||
# make extcoff = Convert ELF to AVR Extended COFF. | |||
# | |||
# make program = Download the hex file to the device. | |||
# Please customize your programmer settings(PROGRAM_CMD) | |||
# | |||
# make teensy = Download the hex file to the device, using teensy_loader_cli. | |||
# (must have teensy_loader_cli installed). | |||
# | |||
# make dfu = Download the hex file to the device, using dfu-programmer (must | |||
# have dfu-programmer installed). | |||
# | |||
# make flip = Download the hex file to the device, using Atmel FLIP (must | |||
# have Atmel FLIP installed). | |||
# | |||
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer | |||
# (must have dfu-programmer installed). | |||
# | |||
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP | |||
# (must have Atmel FLIP installed). | |||
# | |||
# make debug = Start either simulavr or avarice as specified for debugging, | |||
# with avr-gdb or avr-insight as the front end for debugging. | |||
# | |||
# make filename.s = Just compile filename.c into the assembler code only. | |||
# | |||
# make filename.i = Create a preprocessed source file for use in submitting | |||
# bug reports to the GCC project. | |||
# | |||
# To rebuild project do "make clean" then "make all". | |||
#---------------------------------------------------------------------------- | |||
# Target file name (without extension). | |||
TARGET = hhkb_lufa | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# List C source files here. (C dependencies are automatically generated.) | |||
SRC += keymap.c \ | |||
matrix.c \ | |||
led.c | |||
CONFIG_H = config.h | |||
# MCU name | |||
MCU = at90usb1286 | |||
#MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
MOUSEKEY_ENABLE = yes # Mouse keys | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
#NKRO_ENABLE = yes # USB Nkey Rollover | |||
#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support | |||
# Boot Section Size in bytes | |||
# Teensy halfKay 512 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
#OPT_DEFS += -DBOOT_SIZE=4096 | |||
# Search Path | |||
VPATH += $(TARGET_DIR) | |||
VPATH += $(TOP_DIR) | |||
include $(TOP_DIR)/protocol/lufa.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |