Jack and Evan.pull/629/head
@ -0,0 +1,75 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
ifndef QUANTUM_DIR | |||
include ../../Makefile | |||
endif | |||
@ -0,0 +1,162 @@ | |||
/* | |||
Copyright 2012 Jun Wako <wakojun@gmail.com> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xFEAE | |||
#define PRODUCT_ID 0x8844 | |||
#define DEVICE_VER 0x0002 | |||
#define MANUFACTURER Evan Sailer | |||
#define PRODUCT TheVan 44 | |||
#define DESCRIPTION keyboard firmware for TV44 | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 4 | |||
#define MATRIX_COLS 12 | |||
/* | |||
* Keyboard Matrix Assignments | |||
* | |||
* Change this to how you wired your keyboard | |||
* COLS: AVR pins used for columns, left to right | |||
* ROWS: AVR pins used for rows, top to bottom | |||
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) | |||
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) | |||
* | |||
*/ | |||
#define MATRIX_ROW_PINS { D7, B5, F7, D4 } | |||
#define MATRIX_COL_PINS { D2, D3, D5, D6, B4, B6, F6, F5, F4, F1, F0, B3 } | |||
#define UNUSED_PINS | |||
/* COL2ROW or ROW2COL */ | |||
#define DIODE_DIRECTION COL2ROW | |||
// #define BACKLIGHT_PIN B7 | |||
// #define BACKLIGHT_BREATHING | |||
// #define BACKLIGHT_LEVELS 3 | |||
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ | |||
#define DEBOUNCING_DELAY 5 | |||
/* define if matrix has ghost (lacks anti-ghosting diodes) */ | |||
//#define MATRIX_HAS_GHOST | |||
/* number of backlight levels */ | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
/* | |||
* Force NKRO | |||
* | |||
* Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved | |||
* state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the | |||
* makefile for this to work.) | |||
* | |||
* If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) | |||
* until the next keyboard reset. | |||
* | |||
* NKRO may prevent your keystrokes from being detected in the BIOS, but it is | |||
* fully operational during normal computer usage. | |||
* | |||
* For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) | |||
* or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by | |||
* bootmagic, NKRO mode will always be enabled until it is toggled again during a | |||
* power-up. | |||
* | |||
*/ | |||
//#define FORCE_NKRO | |||
/* | |||
* Magic Key Options | |||
* | |||
* Magic keys are hotkey commands that allow control over firmware functions of | |||
* the keyboard. They are best used in combination with the HID Listen program, | |||
* found here: https://www.pjrc.com/teensy/hid_listen.html | |||
* | |||
* The options below allow the magic key functionality to be changed. This is | |||
* useful if your keyboard/keypad is missing keys and you want magic key support. | |||
* | |||
*/ | |||
/* key combination for magic key command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
/* control how magic key switches layers */ | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false | |||
/* override magic key keymap */ | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM | |||
//#define MAGIC_KEY_HELP1 H | |||
//#define MAGIC_KEY_HELP2 SLASH | |||
//#define MAGIC_KEY_DEBUG D | |||
//#define MAGIC_KEY_DEBUG_MATRIX X | |||
//#define MAGIC_KEY_DEBUG_KBD K | |||
//#define MAGIC_KEY_DEBUG_MOUSE M | |||
//#define MAGIC_KEY_VERSION V | |||
//#define MAGIC_KEY_STATUS S | |||
//#define MAGIC_KEY_CONSOLE C | |||
//#define MAGIC_KEY_LAYER0_ALT1 ESC | |||
//#define MAGIC_KEY_LAYER0_ALT2 GRAVE | |||
//#define MAGIC_KEY_LAYER0 0 | |||
//#define MAGIC_KEY_LAYER1 1 | |||
//#define MAGIC_KEY_LAYER2 2 | |||
//#define MAGIC_KEY_LAYER3 3 | |||
//#define MAGIC_KEY_LAYER4 4 | |||
//#define MAGIC_KEY_LAYER5 5 | |||
//#define MAGIC_KEY_LAYER6 6 | |||
//#define MAGIC_KEY_LAYER7 7 | |||
//#define MAGIC_KEY_LAYER8 8 | |||
//#define MAGIC_KEY_LAYER9 9 | |||
//#define MAGIC_KEY_BOOTLOADER PAUSE | |||
//#define MAGIC_KEY_LOCK CAPS | |||
//#define MAGIC_KEY_EEPROM E | |||
//#define MAGIC_KEY_NKRO N | |||
//#define MAGIC_KEY_SLEEP_LED Z | |||
/* | |||
* Feature disable options | |||
* These options are also useful to firmware size reduction. | |||
*/ | |||
/* disable debug print */ | |||
//#define NO_DEBUG | |||
/* disable print */ | |||
//#define NO_PRINT | |||
/* disable action features */ | |||
//#define NO_ACTION_LAYER | |||
//#define NO_ACTION_TAPPING | |||
//#define NO_ACTION_ONESHOT | |||
//#define NO_ACTION_MACRO | |||
//#define NO_ACTION_FUNCTION | |||
#endif |
@ -0,0 +1,21 @@ | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |||
MIDI_ENABLE = no # MIDI controls | |||
AUDIO_ENABLE = no # Audio output on port C6 | |||
UNICODE_ENABLE = no # Unicode | |||
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
ifndef QUANTUM_DIR | |||
include ../../../../Makefile | |||
endif |
@ -0,0 +1,8 @@ | |||
#ifndef CONFIG_USER_H | |||
#define CONFIG_USER_H | |||
#include "../../config.h" | |||
// place overrides here | |||
#endif |
@ -0,0 +1,97 @@ | |||
#include "tv44.h" | |||
#include "action_layer.h" | |||
#include "eeconfig.h" | |||
extern keymap_config_t keymap_config; | |||
// Each layer gets a name for readability, which is then used in the keymap matrix below. | |||
// The underscores don't mean anything - you can have a layer called STUFF or any other name. | |||
// Layer names don't all need to be of the same length, obviously, and you can also skip them | |||
// entirely and just use numbers. | |||
#define _QW 0 | |||
#define _DV 1 | |||
#define _CM 2 | |||
#define _L1 3 | |||
#define _L2 4 | |||
#define _L3 5 | |||
// Macro name shortcuts | |||
#define QWERTY M(_QW) | |||
#define DVORAK M(_DV) | |||
#define COLEMAK M(_CM) | |||
// Fillers to make layering more clear | |||
#define _______ KC_TRNS | |||
#define XXXXXXX KC_NO | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
[_QW] = { /* Qwerty */ | |||
{KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC }, | |||
{MO(_L1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, MO(_L1) }, | |||
{KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_F, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2) }, | |||
{KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) } | |||
}, | |||
[_DV] = { /* Dvorak */ | |||
{KC_TAB, KC_COMM, KC_DOT, KC_SLSH, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_BSPC }, | |||
{MO(_L1), KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, MO(_L1) }, | |||
{KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, MO(_L2) }, | |||
{KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) } | |||
}, | |||
[_CM] = { /* Colemak */ | |||
{KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC }, | |||
{MO(_L1), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, MO(_L1) }, | |||
{KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2) }, | |||
{KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) } | |||
}, | |||
[_L1] = { /* LAYER 1 */ | |||
{KC_GRV, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL }, | |||
{_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_DOWN, KC_UP, KC_LEFT, KC_RGHT, _______ }, | |||
{_______, KC_ESC, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT }, | |||
{_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ } | |||
}, | |||
[_L2] = { /* LAYER 2 */ | |||
{_______, QWERTY, DVORAK, COLEMAK, _______, _______, _______, KC_7, KC_8, KC_9, KC_0, _______ }, | |||
{KC_ESC, KC_PIPE, KC_DQUO, KC_UNDS, KC_PLUS, LSFT(KC_LBRC), LSFT(KC_RBRC), KC_4, KC_5, KC_6, KC_VOLU, KC_ENT }, | |||
{_______, _______, _______, _______, _______, _______, KC_0, KC_1, KC_2, KC_3, KC_VOLD, _______ }, | |||
{_______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ } | |||
}, | |||
[_L3] = { /* LAYER 3 */ | |||
{_______, _______, _______, _______, _______, _______, _______, KC_F1, KC_F2, KC_F3, KC_F4, _______ }, | |||
{KC_ESC, _______, _______, _______, _______, _______, _______, KC_F5, KC_F6, KC_F7, KC_F8, _______ }, | |||
{KC_LSFT, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_F9, KC_F10, KC_F11, KC_F12, _______ }, | |||
{_______, KC_LSFT, KC_B, KC_SPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_C, _______, _______, XXXXXXX, _______ } | |||
} | |||
}; | |||
const uint16_t PROGMEM fn_actions[] = { | |||
}; | |||
void persistant_default_layer_set(uint16_t default_layer) { | |||
eeconfig_update_default_layer(default_layer); | |||
default_layer_set(default_layer); | |||
} | |||
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) | |||
{ | |||
switch(id) { | |||
case _DV: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_DV); | |||
} | |||
break; | |||
case _QW: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_QW); | |||
} | |||
break; | |||
case _CM: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_CM); | |||
} | |||
break; | |||
} | |||
return MACRO_NONE; | |||
}; |
@ -0,0 +1 @@ | |||
# The default keymap for tv44 |
@ -0,0 +1,21 @@ | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |||
MIDI_ENABLE = no # MIDI controls | |||
AUDIO_ENABLE = no # Audio output on port C6 | |||
UNICODE_ENABLE = no # Unicode | |||
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
ifndef QUANTUM_DIR | |||
include ../../../../Makefile | |||
endif |
@ -0,0 +1,8 @@ | |||
#ifndef CONFIG_USER_H | |||
#define CONFIG_USER_H | |||
#include "../../config.h" | |||
// place overrides here | |||
#endif |
@ -0,0 +1,92 @@ | |||
#include "tv44.h" | |||
#include "action_layer.h" | |||
#include "eeconfig.h" | |||
extern keymap_config_t keymap_config; | |||
#define _DV 0 | |||
#define _QW 1 | |||
#define _CM 2 | |||
#define _L1 3 | |||
#define _L2 4 | |||
// Macro name shortcuts | |||
#define DVORAK M(_DV) | |||
#define QWERTY M(_QW) | |||
#define COLEMAK M(_CM) | |||
// Fillers to make layering more clear | |||
#define _______ KC_TRNS | |||
#define XXXXXXX KC_NO | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
[_DV] = { /* 0: Dvorak */ | |||
{KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC }, | |||
{MO(_L1), KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_ENT }, | |||
{KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_RSFT }, | |||
{KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } | |||
}, | |||
[_QW] = { /* 1: Qwerty */ | |||
{KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC }, | |||
{MO(_L1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT }, | |||
{KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT }, | |||
{KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } | |||
}, | |||
[_CM] = { /* 2: Colemak */ | |||
{KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC }, | |||
{MO(_L1), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_ENT }, | |||
{KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT }, | |||
{KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } | |||
}, | |||
[_L1] = {/* 1: FN 1 */ | |||
{KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL }, | |||
{_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_DOWN, KC_UP, KC_LEFT, KC_RGHT, _______ }, | |||
{_______, _______, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT }, | |||
{KC_ESC, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, KC_SLSH, _______, _______ } | |||
}, | |||
[_L2] = { /* 2: FN 2 */ | |||
{KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_ESC }, | |||
{_______, KC_F11, KC_F12, _______, _______, _______, _______, _______, KC_HOME, KC_PGUP, KC_VOLU, KC_ENT }, | |||
{_______, _______, _______, _______, _______, _______, _______, _______, KC_END, KC_PGDN, KC_VOLD, _______ }, | |||
{QWERTY, DVORAK, COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______ } | |||
} | |||
}; | |||
const uint16_t PROGMEM fn_actions[] = { | |||
}; | |||
void persistant_default_layer_set(uint16_t default_layer) { | |||
eeconfig_update_default_layer(default_layer); | |||
default_layer_set(default_layer); | |||
} | |||
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) | |||
{ | |||
switch(id) { | |||
case _DV: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_DV); | |||
} | |||
break; | |||
case _QW: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_QW); | |||
} | |||
break; | |||
case _CM: | |||
if (record->event.pressed) { | |||
persistant_default_layer_set(1UL<<_CM); | |||
} | |||
break; | |||
} | |||
return MACRO_NONE; | |||
}; | |||
@ -0,0 +1 @@ | |||
# The default keymap for tv44 |
@ -0,0 +1,28 @@ | |||
tv44 keyboard firmware | |||
====================== | |||
## Quantum MK Firmware | |||
For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). | |||
## Building | |||
Download or clone the whole firmware and navigate to the keyboards/tv44 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. | |||
Depending on which keymap you would like to use, you will have to compile slightly differently. | |||
### Default | |||
To build with the default keymap, simply run `make`. | |||
### Other Keymaps | |||
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files. | |||
To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: | |||
``` | |||
$ make keymap=[default|jack|<name>] | |||
``` | |||
Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/` |
@ -0,0 +1,28 @@ | |||
#include "tv44.h" | |||
void matrix_init_kb(void) { | |||
// put your keyboard start-up code here | |||
// runs once when the firmware starts up | |||
matrix_init_user(); | |||
} | |||
void matrix_scan_kb(void) { | |||
// put your looping keyboard code here | |||
// runs every cycle (a lot) | |||
matrix_scan_user(); | |||
} | |||
bool process_record_kb(uint16_t keycode, keyrecord_t *record) { | |||
// put your per-action keyboard code here | |||
// runs for every action, just before processing by the firmware | |||
return process_record_user(keycode, record); | |||
} | |||
void led_set_kb(uint8_t usb_led) { | |||
// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here | |||
led_set_user(usb_led); | |||
} |
@ -0,0 +1,22 @@ | |||
#ifndef TV44_H | |||
#define TV44_H | |||
#include "quantum.h" | |||
// This a shortcut to help you visually see your layout. | |||
// The following is an example using the Planck MIT layout | |||
// The first section contains all of the arguements | |||
// The second converts the arguments into a two-dimensional array | |||
#define KEYMAP( \ | |||
K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ | |||
K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ | |||
K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ | |||
K30, K31, K32, K33, K37, K38, K39, K3B \ | |||
) \ | |||
{ \ | |||
{ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ | |||
{ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ | |||
{ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ | |||
{ K30, K31, K32, K33, KC_NO, KC_NO, KC_NO, K37, K38, K39, K3A, K3B } \ | |||
#endif |