* [Keyboard] Add Mixi Co-authored-by: Ryan <fauxpark@gmail.com> Co-authored-by: Ryan <fauxpark@gmail.com>pull/9466/head
@ -0,0 +1,47 @@ | |||
#pragma once | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0x4752 | |||
#define PRODUCT_ID 0x4D49 | |||
#define DEVICE_VER 0x0001 | |||
#define MANUFACTURER gregorio | |||
#define PRODUCT Mixi | |||
#define DESCRIPTION Mixi macropad by gregorio | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 3 | |||
#define MATRIX_COLS 3 | |||
/* Keyboard Matrix Assignments */ | |||
#define DIRECT_PINS { \ | |||
{ D1, D4, F4 }, \ | |||
{ D0, B4, F5 }, \ | |||
{ C6, F7, B6 } \ | |||
} | |||
#define ENCODERS_PAD_A { F5 } | |||
#define ENCODERS_PAD_B { F4 } | |||
/* Set 0 if debouncing isn't needed */ | |||
#define DEBOUNCE 5 | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
#define RGB_DI_PIN B5 | |||
#ifdef RGB_DI_PIN | |||
#define RGBLED_NUM 5 | |||
#define RGBLIGHT_HUE_STEP 8 | |||
#define RGBLIGHT_SAT_STEP 8 | |||
#define RGBLIGHT_VAL_STEP 8 | |||
#define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ | |||
#define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ | |||
#define RGBLIGHT_ANIMATIONS | |||
#define RGBLIGHT_LAYERS | |||
#define RGBLIGHT_LAYER_BLINK | |||
#endif |
@ -0,0 +1,22 @@ | |||
{ | |||
"keyboard_name": "Mixi", | |||
"url": "https://tokopedia.com/sell-stuffs", | |||
"maintainer": "ohchiko", | |||
"width": 3, | |||
"height": 3, | |||
"layouts": { | |||
"LAYOUT": { | |||
"layout": [ | |||
{"x":0, "y":0}, | |||
{"x":1, "y":0}, | |||
{"x":2, "y":0}, | |||
{"x":0, "y":1}, | |||
{"x":1, "y":1}, | |||
{"x":2, "y":1}, | |||
{"x":0, "y":2}, | |||
{"x":1, "y":2}, | |||
{"x":2, "y":2} | |||
] | |||
} | |||
} | |||
} |
@ -0,0 +1,116 @@ | |||
#include QMK_KEYBOARD_H | |||
// please change this value to the desired layer definitions | |||
#define LAYERNUM 3 | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
/* | |||
* | Knob: Layer +/- | | |||
* .---------------------------------------. | |||
* | Mute | Play/Pause | Hold: Layer 2 | | |||
* |----------|------------|---------------| | |||
* | Previous | Up | Next | | |||
* |----------|------------|---------------| | |||
* | Left | Down | Right | | |||
* '---------------------------------------' | |||
*/ | |||
[0] = | |||
LAYOUT( | |||
KC_MUTE, KC_MPLY, MO(2), | |||
KC_MNXT, KC_UP , KC_MPRV , | |||
KC_LEFT, KC_DOWN , KC_RGHT | |||
), | |||
/* | |||
* .-----------------------. | |||
* | NUM 7 | NUM 8 | NUM 9 | | |||
* |-------|-------|-------| | |||
* | NUM 4 | NUM 5 | NUM 6 | | |||
* |-------|-------|-------| | |||
* | NUM 1 | NUM 2 | NUM 3 | | |||
* '-----------------------' | |||
*/ | |||
[1] = | |||
LAYOUT( | |||
KC_P7, KC_P8, KC_P8, | |||
KC_P4, KC_P5, KC_P6, | |||
KC_P1, KC_P2, KC_P3 | |||
), | |||
/* | |||
* | Knob: Volume +/- | | |||
* .--------------------------------------. | |||
* | N/A | N/A | Hold: Layer 2 | | |||
* |--------------|-------|---------------| | |||
* | RESET EEPROM | RESET | DEBUG MODE | | |||
* |--------------|-------|---------------| | |||
* | N/A | N/A | N/A | | |||
* '--------------------------------------' | |||
*/ | |||
[2] = | |||
LAYOUT( | |||
KC_NO , KC_NO, KC_TRNS, | |||
EEP_RST, RESET, DEBUG , | |||
KC_NO , KC_NO, KC_NO | |||
) | |||
}; | |||
const rgblight_segment_t PROGMEM _base_layer[] = RGBLIGHT_LAYER_SEGMENTS( | |||
{0, RGBLED_NUM, HSV_WHITE} | |||
); | |||
const rgblight_segment_t PROGMEM _middle_layer[] = RGBLIGHT_LAYER_SEGMENTS( | |||
{0, RGBLED_NUM, HSV_GREEN} | |||
); | |||
const rgblight_segment_t PROGMEM _top_layer[] = RGBLIGHT_LAYER_SEGMENTS( | |||
{0, RGBLED_NUM, HSV_RED} | |||
); | |||
const rgblight_segment_t* const PROGMEM _rgb_layers[] = | |||
RGBLIGHT_LAYERS_LIST( | |||
_base_layer, | |||
_middle_layer, | |||
_top_layer | |||
); | |||
void keyboard_post_init_user(void) { | |||
rgblight_layers = _rgb_layers; | |||
} | |||
layer_state_t layer_state_set_user(layer_state_t state) { | |||
switch (get_highest_layer(state)) { | |||
case 0: | |||
rgblight_blink_layer(0, 500); | |||
break; | |||
case 1: | |||
rgblight_blink_layer(1, 500); | |||
break; | |||
case 2: | |||
rgblight_blink_layer(2, 500); | |||
break; | |||
} | |||
return state; | |||
} | |||
uint8_t selected_layer = 0; | |||
void encoder_update_user(uint8_t index, bool clockwise) { | |||
if (index == 0) { | |||
if (layer_state_is(2)) { | |||
if (clockwise) { | |||
tap_code(KC_VOLU); | |||
} else { | |||
tap_code(KC_VOLD); | |||
} | |||
} else { | |||
if (clockwise && selected_layer < (LAYERNUM-2)) { /* Prevent switch to layer 2 using encoder */ | |||
selected_layer++; | |||
layer_move(selected_layer); | |||
} else if (!clockwise && selected_layer > 0) { | |||
selected_layer--; | |||
layer_move(selected_layer); | |||
} | |||
} | |||
} | |||
} |
@ -0,0 +1,10 @@ | |||
![Mixi Layout Image](https://i.imgur.com/UIXj9O6.png) | |||
# Default Mixi Layout | |||
This is the default layout that comes flashed on every Mixi macropad. Layer 1 | |||
and Layer 2 are accessible by rotating the encoder. Layer 3 is not accessible | |||
by the encoder, instead is accessible by holding the [0,2] key on Layer 1. While | |||
Layer 3 is active, rotating the encoder will results in increasing/decreasing | |||
media volume. This layout is expected the encoder is on the left side or [0,0] | |||
key. |
@ -0,0 +1,116 @@ | |||
#include QMK_KEYBOARD_H | |||
// please change this value to the desired layer definitions | |||
#define LAYERNUM 3 | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
/* | |||
* | Knob: Layer +/- | | |||
* .---------------------------------------. | |||
* | Mute | Play/Pause | Hold: Layer 2 | | |||
* |----------|------------|---------------| | |||
* | Previous | Up | Next | | |||
* |----------|------------|---------------| | |||
* | Left | Down | Right | | |||
* '---------------------------------------' | |||
*/ | |||
[0] = | |||
LAYOUT( | |||
KC_MUTE, KC_MPLY, MO(2), | |||
KC_MNXT, KC_UP , KC_MPRV , | |||
KC_LEFT, KC_DOWN , KC_RGHT | |||
), | |||
/* | |||
* .-----------------------. | |||
* | NUM 7 | NUM 8 | NUM 9 | | |||
* |-------|-------|-------| | |||
* | NUM 4 | NUM 5 | NUM 6 | | |||
* |-------|-------|-------| | |||
* | NUM 1 | NUM 2 | NUM 3 | | |||
* '-----------------------' | |||
*/ | |||
[1] = | |||
LAYOUT( | |||
KC_P7, KC_P8, KC_P8, | |||
KC_P4, KC_P5, KC_P6, | |||
KC_P1, KC_P2, KC_P3 | |||
), | |||
/* | |||
* | Knob: Volume +/- | | |||
* .--------------------------------------. | |||
* | N/A | N/A | Hold: Layer 2 | | |||
* |--------------|-------|---------------| | |||
* | RESET EEPROM | RESET | DEBUG MODE | | |||
* |--------------|-------|---------------| | |||
* | N/A | N/A | N/A | | |||
* '--------------------------------------' | |||
*/ | |||
[2] = | |||
LAYOUT( | |||
KC_NO , KC_NO, KC_TRNS, | |||
EEP_RST, RESET, DEBUG , | |||
KC_NO , KC_NO, KC_NO | |||
) | |||
}; | |||
const rgblight_segment_t PROGMEM _base_layer[] = RGBLIGHT_LAYER_SEGMENTS( | |||
{0, RGBLED_NUM, HSV_WHITE} | |||
); | |||
const rgblight_segment_t PROGMEM _middle_layer[] = RGBLIGHT_LAYER_SEGMENTS( | |||
{0, RGBLED_NUM, HSV_GREEN} | |||
); | |||
const rgblight_segment_t PROGMEM _top_layer[] = RGBLIGHT_LAYER_SEGMENTS( | |||
{0, RGBLED_NUM, HSV_RED} | |||
); | |||
const rgblight_segment_t* const PROGMEM _rgb_layers[] = | |||
RGBLIGHT_LAYERS_LIST( | |||
_base_layer, | |||
_middle_layer, | |||
_top_layer | |||
); | |||
void keyboard_post_init_user(void) { | |||
rgblight_layers = _rgb_layers; | |||
} | |||
layer_state_t layer_state_set_user(layer_state_t state) { | |||
switch (get_highest_layer(state)) { | |||
case 0: | |||
rgblight_blink_layer(0, 500); | |||
break; | |||
case 1: | |||
rgblight_blink_layer(1, 500); | |||
break; | |||
case 2: | |||
rgblight_blink_layer(2, 500); | |||
break; | |||
} | |||
return state; | |||
} | |||
uint8_t selected_layer = 0; | |||
void encoder_update_user(uint8_t index, bool clockwise) { | |||
if (index == 0) { | |||
if (layer_state_is(2)) { | |||
if (clockwise) { | |||
tap_code(KC_VOLU); | |||
} else { | |||
tap_code(KC_VOLD); | |||
} | |||
} else { | |||
if (clockwise && selected_layer < (LAYERNUM-2)) { /* Prevent switch to layer 2 using encoder */ | |||
selected_layer++; | |||
layer_move(selected_layer); | |||
} else if (!clockwise && selected_layer > 0) { | |||
selected_layer--; | |||
layer_move(selected_layer); | |||
} | |||
} | |||
} | |||
} |
@ -0,0 +1,2 @@ | |||
VIA_ENABLE = yes | |||
LTO_ENABLE = yes |
@ -0,0 +1,13 @@ | |||
#include "mixi.h" | |||
void eeconfig_init_kb(void) { | |||
#ifdef RGBLIGHT_ENABLE | |||
rgblight_enable(); // Enable RGB underglow by default | |||
#ifdef RGBLIGHT_ANIMATIONS | |||
rgblight_mode(RGBLIGHT_MODE_TWINKLE + 5); // Set to RGB_TWINKLE animation by default | |||
#endif | |||
#endif | |||
eeconfig_update_kb(0); | |||
eeconfig_init_user(); | |||
} |
@ -0,0 +1,13 @@ | |||
#pragma once | |||
#include "quantum.h" | |||
#define LAYOUT( \ | |||
K00, K01, K02, \ | |||
K10, K11, K12, \ | |||
K20, K21, K22 \ | |||
) { \ | |||
{ K00, K01, K02 }, \ | |||
{ K10, K11, K12 }, \ | |||
{ K20, K21, K22 } \ | |||
} |
@ -0,0 +1,15 @@ | |||
# Mixi | |||
![Mixi](https://i.imgur.com/GPO6Khu.jpg) | |||
A mini 3x3 macropad with rotary encoders support and RGB underglow and also tray mount support. Currently the PCB and kits can only be purchased in Indonesia. | |||
* Keyboard Maintainer: [ohchiko](https://github.com/ohchiko) | |||
* Hardware Supported: Mixi PCB, Arduino Pro Micro | |||
* Hardware Availability: [Tokopedia/Sell Stuffs](https://tokopedia.com/sell-stuffs) (Indonesia only). | |||
Make example for this keyboard (after setting up your build environment): | |||
make mixi:default | |||
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). |
@ -0,0 +1,27 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Bootloader selection | |||
# Teensy halfkay | |||
# Pro Micro caterina | |||
# Atmel DFU atmel-dfu | |||
# LUFA DFU lufa-dfu | |||
# QMK DFU qmk-dfu | |||
# ATmega32A bootloadHID | |||
# ATmega328P USBasp | |||
BOOTLOADER = caterina | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration | |||
MOUSEKEY_ENABLE = no # Mouse keys | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
CONSOLE_ENABLE = yes # Console for debug | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE = no # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |||
RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow | |||
ENCODER_ENABLE = yes | |||
AUDIO_ENABLE = no |