This adds basic support for JM60 RGB PCB that was sold by KBDfans https://kbdfans.myshopify.com/ https://www.aliexpress.com/store/product/JM60-RGB60-Custom-mechanical-keyboard-PCB-ANSI/2230037_32810956675.html No support for RGB Backlight yet.pull/1711/head
@ -0,0 +1,3 @@ | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,51 @@ | |||
/* | |||
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio | |||
Licensed under the Apache License, Version 2.0 (the "License"); | |||
you may not use this file except in compliance with the License. | |||
You may obtain a copy of the License at | |||
http://www.apache.org/licenses/LICENSE-2.0 | |||
Unless required by applicable law or agreed to in writing, software | |||
distributed under the License is distributed on an "AS IS" BASIS, | |||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |||
See the License for the specific language governing permissions and | |||
limitations under the License. | |||
*/ | |||
#include "hal.h" | |||
/** | |||
* @brief PAL setup. | |||
* @details Digital I/O ports static configuration as defined in @p board.h. | |||
* This variable is used by the HAL when initializing the PAL driver. | |||
*/ | |||
#if HAL_USE_PAL || defined(__DOXYGEN__) | |||
const PALConfig pal_default_config = | |||
{ | |||
{VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, | |||
{VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, | |||
{VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, | |||
{VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, | |||
{VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, | |||
}; | |||
#endif | |||
/* | |||
* Early initialization code. | |||
* This initialization must be performed just after stack setup and before | |||
* any other initialization. | |||
*/ | |||
void __early_init(void) { | |||
stm32_clock_init(); | |||
} | |||
/* | |||
* Board-specific initialization code. | |||
*/ | |||
void boardInit(void) { | |||
AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE; | |||
} |
@ -0,0 +1,142 @@ | |||
/* | |||
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio | |||
Licensed under the Apache License, Version 2.0 (the "License"); | |||
you may not use this file except in compliance with the License. | |||
You may obtain a copy of the License at | |||
http://www.apache.org/licenses/LICENSE-2.0 | |||
Unless required by applicable law or agreed to in writing, software | |||
distributed under the License is distributed on an "AS IS" BASIS, | |||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |||
See the License for the specific language governing permissions and | |||
limitations under the License. | |||
*/ | |||
#ifndef _BOARD_H_ | |||
#define _BOARD_H_ | |||
/* | |||
* Board identifier. | |||
*/ | |||
#define BOARD_JM60 | |||
#define BOARD_NAME "JM60 keyboard" | |||
/* | |||
* Board frequencies. | |||
*/ | |||
#define STM32_LSECLK 32768 | |||
#define STM32_HSECLK 8000000 | |||
/* | |||
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. | |||
* | |||
* Only xB (128KB Flash) is defined, but it's identical to the | |||
* x8 version (64KB Flash) except for the Flash region size in the | |||
* linker script. For x8 parts use xB here and change to the x8 linker | |||
* script in the project Makefile. | |||
*/ | |||
#define STM32F103xB | |||
/* | |||
* IO pins assignments | |||
* | |||
* numbering is sorted by onboard/connectors, as from the schematics in | |||
* http://www.vcc-gnd.com/read.php?tid=369 | |||
*/ | |||
/* on-board */ | |||
#define GPIOA_USBDM 11 // pin 8 | |||
#define GPIOA_USBDP 12 // pin 9 | |||
#define GPIOC_OSC32_IN 14 | |||
#define GPIOC_OSC32_OUT 15 | |||
/* | |||
* I/O ports initial setup, this configuration is established soon after reset | |||
* in the initialization code. | |||
* | |||
* The digits have the following meaning: | |||
* 0 - Analog input. | |||
* 1 - Push Pull output 10MHz. | |||
* 2 - Push Pull output 2MHz. | |||
* 3 - Push Pull output 50MHz. | |||
* 4 - Digital input. | |||
* 5 - Open Drain output 10MHz. | |||
* 6 - Open Drain output 2MHz. | |||
* 7 - Open Drain output 50MHz. | |||
* 8 - Digital input with PullUp or PullDown resistor depending on ODR. | |||
* 9 - Alternate Push Pull output 10MHz. | |||
* A - Alternate Push Pull output 2MHz. | |||
* B - Alternate Push Pull output 50MHz. | |||
* C - Reserved. | |||
* D - Alternate Open Drain output 10MHz. | |||
* E - Alternate Open Drain output 2MHz. | |||
* F - Alternate Open Drain output 50MHz. | |||
* Please refer to the STM32 Reference Manual for details. | |||
*/ | |||
/* | |||
* Port A setup. | |||
* Everything input with pull-up except: | |||
*/ | |||
#define VAL_GPIOACRL 0x88888888 /* PA7...PA0 */ | |||
#define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */ | |||
#define VAL_GPIOAODR 0xFFFFFFFF | |||
/* | |||
* Port B setup. | |||
* Everything input with pull-up except: | |||
*/ | |||
#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ | |||
#define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */ | |||
#define VAL_GPIOBODR 0xFFFFFFFF | |||
/* | |||
* Port C setup. | |||
* Everything input with pull-up except: | |||
*/ | |||
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ | |||
#define VAL_GPIOCCRH 0x88888888 /* PC15...PC8 */ | |||
#define VAL_GPIOCODR 0xFFFFFFFF | |||
/* | |||
* Port D setup. | |||
* Everything input with pull-up except: | |||
* PD0 - Normal input (XTAL). | |||
* PD1 - Normal input (XTAL). | |||
*/ | |||
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ | |||
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ | |||
#define VAL_GPIODODR 0xFFFFFFFF | |||
/* | |||
* Port E setup. | |||
* Everything input with pull-up except: | |||
*/ | |||
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ | |||
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ | |||
#define VAL_GPIOEODR 0xFFFFFFFF | |||
/* | |||
* USB bus activation macro, required by the USB driver. | |||
*/ | |||
#define usb_lld_connect_bus(usbp) /* always connected */ | |||
/* | |||
* USB bus de-activation macro, required by the USB driver. | |||
*/ | |||
#define usb_lld_disconnect_bus(usbp) /* always connected */ | |||
#if !defined(_FROM_ASM_) | |||
#ifdef __cplusplus | |||
extern "C" { | |||
#endif | |||
void boardInit(void); | |||
#ifdef __cplusplus | |||
} | |||
#endif | |||
#endif /* _FROM_ASM_ */ | |||
#endif /* _BOARD_H_ */ |
@ -0,0 +1,5 @@ | |||
# List of all the board related files. | |||
BOARDSRC = $(KEYBOARD_PATH)/boards/JM60_BOARD/board.c | |||
# Required include directories | |||
BOARDINC = $(KEYBOARD_PATH)/boards/JM60_BOARD |
@ -0,0 +1,524 @@ | |||
/* | |||
ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio | |||
Licensed under the Apache License, Version 2.0 (the "License"); | |||
you may not use this file except in compliance with the License. | |||
You may obtain a copy of the License at | |||
http://www.apache.org/licenses/LICENSE-2.0 | |||
Unless required by applicable law or agreed to in writing, software | |||
distributed under the License is distributed on an "AS IS" BASIS, | |||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |||
See the License for the specific language governing permissions and | |||
limitations under the License. | |||
*/ | |||
/** | |||
* @file templates/chconf.h | |||
* @brief Configuration file template. | |||
* @details A copy of this file must be placed in each project directory, it | |||
* contains the application specific kernel settings. | |||
* | |||
* @addtogroup config | |||
* @details Kernel related settings and hooks. | |||
* @{ | |||
*/ | |||
#ifndef CHCONF_H | |||
#define CHCONF_H | |||
#define _CHIBIOS_RT_CONF_ | |||
/*===========================================================================*/ | |||
/** | |||
* @name System timers settings | |||
* @{ | |||
*/ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief System time counter resolution. | |||
* @note Allowed values are 16 or 32 bits. | |||
*/ | |||
#define CH_CFG_ST_RESOLUTION 32 | |||
/** | |||
* @brief System tick frequency. | |||
* @details Frequency of the system timer that drives the system ticks. This | |||
* setting also defines the system tick time unit. | |||
*/ | |||
#define CH_CFG_ST_FREQUENCY 100000 | |||
/** | |||
* @brief Time delta constant for the tick-less mode. | |||
* @note If this value is zero then the system uses the classic | |||
* periodic tick. This value represents the minimum number | |||
* of ticks that is safe to specify in a timeout directive. | |||
* The value one is not valid, timeouts are rounded up to | |||
* this value. | |||
*/ | |||
#define CH_CFG_ST_TIMEDELTA 0 | |||
/** @} */ | |||
/*===========================================================================*/ | |||
/** | |||
* @name Kernel parameters and options | |||
* @{ | |||
*/ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Round robin interval. | |||
* @details This constant is the number of system ticks allowed for the | |||
* threads before preemption occurs. Setting this value to zero | |||
* disables the preemption for threads with equal priority and the | |||
* round robin becomes cooperative. Note that higher priority | |||
* threads can still preempt, the kernel is always preemptive. | |||
* @note Disabling the round robin preemption makes the kernel more compact | |||
* and generally faster. | |||
* @note The round robin preemption is not supported in tickless mode and | |||
* must be set to zero in that case. | |||
*/ | |||
#define CH_CFG_TIME_QUANTUM 20 | |||
/** | |||
* @brief Managed RAM size. | |||
* @details Size of the RAM area to be managed by the OS. If set to zero | |||
* then the whole available RAM is used. The core memory is made | |||
* available to the heap allocator and/or can be used directly through | |||
* the simplified core memory allocator. | |||
* | |||
* @note In order to let the OS manage the whole RAM the linker script must | |||
* provide the @p __heap_base__ and @p __heap_end__ symbols. | |||
* @note Requires @p CH_CFG_USE_MEMCORE. | |||
*/ | |||
#define CH_CFG_MEMCORE_SIZE 0 | |||
/** | |||
* @brief Idle thread automatic spawn suppression. | |||
* @details When this option is activated the function @p chSysInit() | |||
* does not spawn the idle thread. The application @p main() | |||
* function becomes the idle thread and must implement an | |||
* infinite loop. | |||
*/ | |||
#define CH_CFG_NO_IDLE_THREAD FALSE | |||
/* Use __WFI in the idle thread for waiting. Does lower the power | |||
* consumption. */ | |||
#define CORTEX_ENABLE_WFI_IDLE TRUE | |||
/** @} */ | |||
/*===========================================================================*/ | |||
/** | |||
* @name Performance options | |||
* @{ | |||
*/ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief OS optimization. | |||
* @details If enabled then time efficient rather than space efficient code | |||
* is used when two possible implementations exist. | |||
* | |||
* @note This is not related to the compiler optimization options. | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_OPTIMIZE_SPEED TRUE | |||
/** @} */ | |||
/*===========================================================================*/ | |||
/** | |||
* @name Subsystem options | |||
* @{ | |||
*/ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Time Measurement APIs. | |||
* @details If enabled then the time measurement APIs are included in | |||
* the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_TM FALSE | |||
/** | |||
* @brief Threads registry APIs. | |||
* @details If enabled then the registry APIs are included in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_REGISTRY TRUE | |||
/** | |||
* @brief Threads synchronization APIs. | |||
* @details If enabled then the @p chThdWait() function is included in | |||
* the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_WAITEXIT TRUE | |||
/** | |||
* @brief Semaphores APIs. | |||
* @details If enabled then the Semaphores APIs are included in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_SEMAPHORES TRUE | |||
/** | |||
* @brief Semaphores queuing mode. | |||
* @details If enabled then the threads are enqueued on semaphores by | |||
* priority rather than in FIFO order. | |||
* | |||
* @note The default is @p FALSE. Enable this if you have special | |||
* requirements. | |||
* @note Requires @p CH_CFG_USE_SEMAPHORES. | |||
*/ | |||
#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE | |||
/** | |||
* @brief Mutexes APIs. | |||
* @details If enabled then the mutexes APIs are included in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_MUTEXES TRUE | |||
/** | |||
* @brief Enables recursive behavior on mutexes. | |||
* @note Recursive mutexes are heavier and have an increased | |||
* memory footprint. | |||
* | |||
* @note The default is @p FALSE. | |||
* @note Requires @p CH_CFG_USE_MUTEXES. | |||
*/ | |||
#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE | |||
/** | |||
* @brief Conditional Variables APIs. | |||
* @details If enabled then the conditional variables APIs are included | |||
* in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
* @note Requires @p CH_CFG_USE_MUTEXES. | |||
*/ | |||
#define CH_CFG_USE_CONDVARS TRUE | |||
/** | |||
* @brief Conditional Variables APIs with timeout. | |||
* @details If enabled then the conditional variables APIs with timeout | |||
* specification are included in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
* @note Requires @p CH_CFG_USE_CONDVARS. | |||
*/ | |||
#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE | |||
/** | |||
* @brief Events Flags APIs. | |||
* @details If enabled then the event flags APIs are included in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_EVENTS TRUE | |||
/** | |||
* @brief Events Flags APIs with timeout. | |||
* @details If enabled then the events APIs with timeout specification | |||
* are included in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
* @note Requires @p CH_CFG_USE_EVENTS. | |||
*/ | |||
#define CH_CFG_USE_EVENTS_TIMEOUT TRUE | |||
/** | |||
* @brief Synchronous Messages APIs. | |||
* @details If enabled then the synchronous messages APIs are included | |||
* in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_MESSAGES TRUE | |||
/** | |||
* @brief Synchronous Messages queuing mode. | |||
* @details If enabled then messages are served by priority rather than in | |||
* FIFO order. | |||
* | |||
* @note The default is @p FALSE. Enable this if you have special | |||
* requirements. | |||
* @note Requires @p CH_CFG_USE_MESSAGES. | |||
*/ | |||
#define CH_CFG_USE_MESSAGES_PRIORITY FALSE | |||
/** | |||
* @brief Mailboxes APIs. | |||
* @details If enabled then the asynchronous messages (mailboxes) APIs are | |||
* included in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
* @note Requires @p CH_CFG_USE_SEMAPHORES. | |||
*/ | |||
#define CH_CFG_USE_MAILBOXES TRUE | |||
/** | |||
* @brief Core Memory Manager APIs. | |||
* @details If enabled then the core memory manager APIs are included | |||
* in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_MEMCORE TRUE | |||
/** | |||
* @brief Heap Allocator APIs. | |||
* @details If enabled then the memory heap allocator APIs are included | |||
* in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
* @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or | |||
* @p CH_CFG_USE_SEMAPHORES. | |||
* @note Mutexes are recommended. | |||
*/ | |||
#define CH_CFG_USE_HEAP TRUE | |||
/** | |||
* @brief Memory Pools Allocator APIs. | |||
* @details If enabled then the memory pools allocator APIs are included | |||
* in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
*/ | |||
#define CH_CFG_USE_MEMPOOLS TRUE | |||
/** | |||
* @brief Dynamic Threads APIs. | |||
* @details If enabled then the dynamic threads creation APIs are included | |||
* in the kernel. | |||
* | |||
* @note The default is @p TRUE. | |||
* @note Requires @p CH_CFG_USE_WAITEXIT. | |||
* @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. | |||
*/ | |||
#define CH_CFG_USE_DYNAMIC TRUE | |||
/** @} */ | |||
/*===========================================================================*/ | |||
/** | |||
* @name Debug options | |||
* @{ | |||
*/ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Debug option, kernel statistics. | |||
* | |||
* @note The default is @p FALSE. | |||
*/ | |||
#define CH_DBG_STATISTICS FALSE | |||
/** | |||
* @brief Debug option, system state check. | |||
* @details If enabled the correct call protocol for system APIs is checked | |||
* at runtime. | |||
* | |||
* @note The default is @p FALSE. | |||
*/ | |||
#define CH_DBG_SYSTEM_STATE_CHECK FALSE | |||
/** | |||
* @brief Debug option, parameters checks. | |||
* @details If enabled then the checks on the API functions input | |||
* parameters are activated. | |||
* | |||
* @note The default is @p FALSE. | |||
*/ | |||
#define CH_DBG_ENABLE_CHECKS FALSE | |||
/** | |||
* @brief Debug option, consistency checks. | |||
* @details If enabled then all the assertions in the kernel code are | |||
* activated. This includes consistency checks inside the kernel, | |||
* runtime anomalies and port-defined checks. | |||
* | |||
* @note The default is @p FALSE. | |||
*/ | |||
#define CH_DBG_ENABLE_ASSERTS FALSE | |||
/** | |||
* @brief Debug option, trace buffer. | |||
* @details If enabled then the trace buffer is activated. | |||
* | |||
* @note The default is @p CH_DBG_TRACE_MASK_DISABLED. | |||
*/ | |||
#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED | |||
/** | |||
* @brief Trace buffer entries. | |||
* @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is | |||
* different from @p CH_DBG_TRACE_MASK_DISABLED. | |||
*/ | |||
#define CH_DBG_TRACE_BUFFER_SIZE 128 | |||
/** | |||
* @brief Debug option, stack checks. | |||
* @details If enabled then a runtime stack check is performed. | |||
* | |||
* @note The default is @p FALSE. | |||
* @note The stack check is performed in a architecture/port dependent way. | |||
* It may not be implemented or some ports. | |||
* @note The default failure mode is to halt the system with the global | |||
* @p panic_msg variable set to @p NULL. | |||
*/ | |||
#define CH_DBG_ENABLE_STACK_CHECK FALSE | |||
/** | |||
* @brief Debug option, stacks initialization. | |||
* @details If enabled then the threads working area is filled with a byte | |||
* value when a thread is created. This can be useful for the | |||
* runtime measurement of the used stack. | |||
* | |||
* @note The default is @p FALSE. | |||
*/ | |||
#define CH_DBG_FILL_THREADS FALSE | |||
/** | |||
* @brief Debug option, threads profiling. | |||
* @details If enabled then a field is added to the @p thread_t structure that | |||
* counts the system ticks occurred while executing the thread. | |||
* | |||
* @note The default is @p FALSE. | |||
* @note This debug option is not currently compatible with the | |||
* tickless mode. | |||
*/ | |||
#define CH_DBG_THREADS_PROFILING FALSE | |||
/** @} */ | |||
/*===========================================================================*/ | |||
/** | |||
* @name Kernel hooks | |||
* @{ | |||
*/ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Threads descriptor structure extension. | |||
* @details User fields added to the end of the @p thread_t structure. | |||
*/ | |||
#define CH_CFG_THREAD_EXTRA_FIELDS \ | |||
/* Add threads custom fields here.*/ | |||
/** | |||
* @brief Threads initialization hook. | |||
* @details User initialization code added to the @p chThdInit() API. | |||
* | |||
* @note It is invoked from within @p chThdInit() and implicitly from all | |||
* the threads creation APIs. | |||
*/ | |||
#define CH_CFG_THREAD_INIT_HOOK(tp) { \ | |||
/* Add threads initialization code here.*/ \ | |||
} | |||
/** | |||
* @brief Threads finalization hook. | |||
* @details User finalization code added to the @p chThdExit() API. | |||
*/ | |||
#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ | |||
/* Add threads finalization code here.*/ \ | |||
} | |||
/** | |||
* @brief Context switch hook. | |||
* @details This hook is invoked just before switching between threads. | |||
*/ | |||
#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ | |||
/* Context switch code here.*/ \ | |||
} | |||
/** | |||
* @brief ISR enter hook. | |||
*/ | |||
#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ | |||
/* IRQ prologue code here.*/ \ | |||
} | |||
/** | |||
* @brief ISR exit hook. | |||
*/ | |||
#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ | |||
/* IRQ epilogue code here.*/ \ | |||
} | |||
/** | |||
* @brief Idle thread enter hook. | |||
* @note This hook is invoked within a critical zone, no OS functions | |||
* should be invoked from here. | |||
* @note This macro can be used to activate a power saving mode. | |||
*/ | |||
#define CH_CFG_IDLE_ENTER_HOOK() { \ | |||
/* Idle-enter code here.*/ \ | |||
} | |||
/** | |||
* @brief Idle thread leave hook. | |||
* @note This hook is invoked within a critical zone, no OS functions | |||
* should be invoked from here. | |||
* @note This macro can be used to deactivate a power saving mode. | |||
*/ | |||
#define CH_CFG_IDLE_LEAVE_HOOK() { \ | |||
/* Idle-leave code here.*/ \ | |||
} | |||
/** | |||
* @brief Idle Loop hook. | |||
* @details This hook is continuously invoked by the idle thread loop. | |||
*/ | |||
#define CH_CFG_IDLE_LOOP_HOOK() { \ | |||
/* Idle loop code here.*/ \ | |||
} | |||
/** | |||
* @brief System tick event hook. | |||
* @details This hook is invoked in the system tick handler immediately | |||
* after processing the virtual timers queue. | |||
*/ | |||
#define CH_CFG_SYSTEM_TICK_HOOK() { \ | |||
/* System tick event code here.*/ \ | |||
} | |||
/** | |||
* @brief System halt hook. | |||
* @details This hook is invoked in case to a system halting error before | |||
* the system is halted. | |||
*/ | |||
#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ | |||
/* System halt code here.*/ \ | |||
} | |||
/** | |||
* @brief Trace hook. | |||
* @details This hook is invoked each time a new record is written in the | |||
* trace buffer. | |||
*/ | |||
#define CH_CFG_TRACE_HOOK(tep) { \ | |||
/* Trace code here.*/ \ | |||
} | |||
/** @} */ | |||
/*===========================================================================*/ | |||
/* Port-specific settings (override port settings defaulted in chcore.h). */ | |||
/*===========================================================================*/ | |||
#endif /* CHCONF_H */ | |||
/** @} */ |
@ -0,0 +1,80 @@ | |||
/* | |||
Copyright 2015 Jun Wako <wakojun@gmail.com> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#define PREVENT_STUCK_MODIFIERS | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xFEED | |||
#define PRODUCT_ID 0x6464 | |||
#define DEVICE_VER 0x0001 | |||
/* in python2: list(u"whatever".encode('utf-16-le')) */ | |||
/* at most 32 characters or the ugly hack in usb_main.c borks */ | |||
#define MANUFACTURER "QMK" | |||
#define USBSTR_MANUFACTURER 'T', '\x00', 'M', '\x00', 'K', '\x00', ' ', '\x00', '\xc6', '\x00' | |||
#define PRODUCT "JM60" | |||
#define USBSTR_PRODUCT 'J', '\x00', 'M', '\x00', '6', '\x00', '0', '\x00' | |||
#define DESCRIPTION "QMK keyboard firmware for JM60" | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 5 | |||
#define MATRIX_COLS 14 | |||
/* number of backlight levels */ | |||
//#define BACKLIGHT_LEVELS 1 | |||
//#define LED_BRIGHTNESS_LO 100 | |||
//#define LED_BRIGHTNESS_HI 255 | |||
/* define if matrix has ghost */ | |||
//#define MATRIX_HAS_GHOST | |||
/* Set 0 if debouncing isn't needed */ | |||
#define DEBOUNCE 5 | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
//#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
/* key combination for command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
/* | |||
* Feature disable options | |||
* These options are also useful to firmware size reduction. | |||
*/ | |||
/* disable debug print */ | |||
//#define NO_DEBUG | |||
/* disable print */ | |||
//#define NO_PRINT | |||
/* disable action features */ | |||
//#define NO_ACTION_LAYER | |||
//#define NO_ACTION_TAPPING | |||
//#define NO_ACTION_ONESHOT | |||
//#define NO_ACTION_MACRO | |||
//#define NO_ACTION_FUNCTION | |||
#endif |
@ -0,0 +1,353 @@ | |||
/* | |||
ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio | |||
Licensed under the Apache License, Version 2.0 (the "License"); | |||
you may not use this file except in compliance with the License. | |||
You may obtain a copy of the License at | |||
http://www.apache.org/licenses/LICENSE-2.0 | |||
Unless required by applicable law or agreed to in writing, software | |||
distributed under the License is distributed on an "AS IS" BASIS, | |||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |||
See the License for the specific language governing permissions and | |||
limitations under the License. | |||
*/ | |||
/** | |||
* @file templates/halconf.h | |||
* @brief HAL configuration header. | |||
* @details HAL configuration file, this file allows to enable or disable the | |||
* various device drivers from your application. You may also use | |||
* this file in order to override the device drivers default settings. | |||
* | |||
* @addtogroup HAL_CONF | |||
* @{ | |||
*/ | |||
#ifndef _HALCONF_H_ | |||
#define _HALCONF_H_ | |||
#include "mcuconf.h" | |||
/** | |||
* @brief Enables the PAL subsystem. | |||
*/ | |||
#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) | |||
#define HAL_USE_PAL TRUE | |||
#endif | |||
/** | |||
* @brief Enables the ADC subsystem. | |||
*/ | |||
#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) | |||
#define HAL_USE_ADC FALSE | |||
#endif | |||
/** | |||
* @brief Enables the CAN subsystem. | |||
*/ | |||
#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) | |||
#define HAL_USE_CAN FALSE | |||
#endif | |||
/** | |||
* @brief Enables the DAC subsystem. | |||
*/ | |||
#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) | |||
#define HAL_USE_DAC FALSE | |||
#endif | |||
/** | |||
* @brief Enables the EXT subsystem. | |||
*/ | |||
#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) | |||
#define HAL_USE_EXT FALSE | |||
#endif | |||
/** | |||
* @brief Enables the GPT subsystem. | |||
*/ | |||
#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) | |||
#define HAL_USE_GPT FALSE | |||
#endif | |||
/** | |||
* @brief Enables the I2C subsystem. | |||
*/ | |||
#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) | |||
#define HAL_USE_I2C FALSE | |||
#endif | |||
/** | |||
* @brief Enables the I2S subsystem. | |||
*/ | |||
#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) | |||
#define HAL_USE_I2S FALSE | |||
#endif | |||
/** | |||
* @brief Enables the ICU subsystem. | |||
*/ | |||
#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) | |||
#define HAL_USE_ICU FALSE | |||
#endif | |||
/** | |||
* @brief Enables the MAC subsystem. | |||
*/ | |||
#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) | |||
#define HAL_USE_MAC FALSE | |||
#endif | |||
/** | |||
* @brief Enables the MMC_SPI subsystem. | |||
*/ | |||
#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) | |||
#define HAL_USE_MMC_SPI FALSE | |||
#endif | |||
/** | |||
* @brief Enables the PWM subsystem. | |||
*/ | |||
#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) | |||
#define HAL_USE_PWM FALSE | |||
#endif | |||
/** | |||
* @brief Enables the RTC subsystem. | |||
*/ | |||
#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) | |||
#define HAL_USE_RTC FALSE | |||
#endif | |||
/** | |||
* @brief Enables the SDC subsystem. | |||
*/ | |||
#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) | |||
#define HAL_USE_SDC FALSE | |||
#endif | |||
/** | |||
* @brief Enables the SERIAL subsystem. | |||
*/ | |||
#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) | |||
#define HAL_USE_SERIAL FALSE | |||
#endif | |||
/** | |||
* @brief Enables the SERIAL over USB subsystem. | |||
*/ | |||
#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) | |||
#define HAL_USE_SERIAL_USB FALSE | |||
#endif | |||
/** | |||
* @brief Enables the SPI subsystem. | |||
*/ | |||
#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) | |||
#define HAL_USE_SPI FALSE | |||
#endif | |||
/** | |||
* @brief Enables the UART subsystem. | |||
*/ | |||
#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) | |||
#define HAL_USE_UART FALSE | |||
#endif | |||
/** | |||
* @brief Enables the USB subsystem. | |||
*/ | |||
#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) | |||
#define HAL_USE_USB TRUE | |||
#endif | |||
/** | |||
* @brief Enables the WDG subsystem. | |||
*/ | |||
#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) | |||
#define HAL_USE_WDG FALSE | |||
#endif | |||
/*===========================================================================*/ | |||
/* ADC driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Enables synchronous APIs. | |||
* @note Disabling this option saves both code and data space. | |||
*/ | |||
#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) | |||
#define ADC_USE_WAIT TRUE | |||
#endif | |||
/** | |||
* @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. | |||
* @note Disabling this option saves both code and data space. | |||
*/ | |||
#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) | |||
#define ADC_USE_MUTUAL_EXCLUSION TRUE | |||
#endif | |||
/*===========================================================================*/ | |||
/* CAN driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Sleep mode related APIs inclusion switch. | |||
*/ | |||
#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) | |||
#define CAN_USE_SLEEP_MODE TRUE | |||
#endif | |||
/*===========================================================================*/ | |||
/* I2C driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Enables the mutual exclusion APIs on the I2C bus. | |||
*/ | |||
#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) | |||
#define I2C_USE_MUTUAL_EXCLUSION TRUE | |||
#endif | |||
/*===========================================================================*/ | |||
/* MAC driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Enables an event sources for incoming packets. | |||
*/ | |||
#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) | |||
#define MAC_USE_ZERO_COPY FALSE | |||
#endif | |||
/** | |||
* @brief Enables an event sources for incoming packets. | |||
*/ | |||
#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) | |||
#define MAC_USE_EVENTS TRUE | |||
#endif | |||
/*===========================================================================*/ | |||
/* MMC_SPI driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Delays insertions. | |||
* @details If enabled this options inserts delays into the MMC waiting | |||
* routines releasing some extra CPU time for the threads with | |||
* lower priority, this may slow down the driver a bit however. | |||
* This option is recommended also if the SPI driver does not | |||
* use a DMA channel and heavily loads the CPU. | |||
*/ | |||
#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) | |||
#define MMC_NICE_WAITING TRUE | |||
#endif | |||
/*===========================================================================*/ | |||
/* SDC driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Number of initialization attempts before rejecting the card. | |||
* @note Attempts are performed at 10mS intervals. | |||
*/ | |||
#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) | |||
#define SDC_INIT_RETRY 100 | |||
#endif | |||
/** | |||
* @brief Include support for MMC cards. | |||
* @note MMC support is not yet implemented so this option must be kept | |||
* at @p FALSE. | |||
*/ | |||
#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) | |||
#define SDC_MMC_SUPPORT FALSE | |||
#endif | |||
/** | |||
* @brief Delays insertions. | |||
* @details If enabled this options inserts delays into the MMC waiting | |||
* routines releasing some extra CPU time for the threads with | |||
* lower priority, this may slow down the driver a bit however. | |||
*/ | |||
#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) | |||
#define SDC_NICE_WAITING TRUE | |||
#endif | |||
/*===========================================================================*/ | |||
/* SERIAL driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Default bit rate. | |||
* @details Configuration parameter, this is the baud rate selected for the | |||
* default configuration. | |||
*/ | |||
#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) | |||
#define SERIAL_DEFAULT_BITRATE 38400 | |||
#endif | |||
/** | |||
* @brief Serial buffers size. | |||
* @details Configuration parameter, you can change the depth of the queue | |||
* buffers depending on the requirements of your application. | |||
* @note The default is 64 bytes for both the transmission and receive | |||
* buffers. | |||
*/ | |||
#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) | |||
#define SERIAL_BUFFERS_SIZE 16 | |||
#endif | |||
/*===========================================================================*/ | |||
/* SERIAL_USB driver related setting. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Serial over USB buffers size. | |||
* @details Configuration parameter, the buffer size must be a multiple of | |||
* the USB data endpoint maximum packet size. | |||
* @note The default is 64 bytes for both the transmission and receive | |||
* buffers. | |||
*/ | |||
#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) | |||
#define SERIAL_USB_BUFFERS_SIZE 256 | |||
#endif | |||
/*===========================================================================*/ | |||
/* SPI driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Enables synchronous APIs. | |||
* @note Disabling this option saves both code and data space. | |||
*/ | |||
#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) | |||
#define SPI_USE_WAIT TRUE | |||
#endif | |||
/** | |||
* @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. | |||
* @note Disabling this option saves both code and data space. | |||
*/ | |||
#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) | |||
#define SPI_USE_MUTUAL_EXCLUSION TRUE | |||
#endif | |||
/*===========================================================================*/ | |||
/* USB driver related settings. */ | |||
/*===========================================================================*/ | |||
/** | |||
* @brief Enables synchronous APIs. | |||
* @note Disabling this option saves both code and data space. | |||
*/ | |||
#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) | |||
#define USB_USE_WAIT TRUE | |||
#endif | |||
#endif /* _HALCONF_H_ */ | |||
/** @} */ |
@ -0,0 +1,17 @@ | |||
/* | |||
Copyright 2012,2013 Jun Wako <wakojun@gmail.com> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#include QMK_KEYBOARD_H |
@ -0,0 +1,53 @@ | |||
/* | |||
Copyright 2014 Jun Wako <wakojun@gmail.com> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#ifndef JM60_H | |||
#define JM60_H | |||
#include "quantum.h" | |||
// readability | |||
#define XXX KC_NO | |||
/* Satan GH60 ANSI layout | |||
* ,-----------------------------------------------------------. | |||
* | 00 |01| 02| 03| 04| 05| 06| 07| 08| 09| 0a| 0b| 0c| 0d | | |||
* |-----------------------------------------------------------| | |||
* | 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1a| 1b| 1c| 1d | | |||
* |-----------------------------------------------------------| | |||
* | 20 | 21| 22| 23| 24| 25| 26| 27| 28| 29| 2a| 2c| 2d | | |||
* |-----------------------------------------------------------| | |||
* | 30 | 31| 32| 33| 34| 35| 36| 37| 38| 39| 3b| 3d | | |||
* |-----------------------------------------------------------| | |||
* | 40 | 41 | 42 | 46 | 4a | 4b | 4c | 4d | | |||
* `-----------------------------------------------------------' | |||
*/ | |||
#define KEYMAP_ANSI( \ | |||
k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, \ | |||
k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \ | |||
k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2c, k2d, \ | |||
k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3b, k3d, \ | |||
k40, k41, k42, k46, k4a, k4b, k4c, k4d \ | |||
) \ | |||
{ \ | |||
{k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d}, \ | |||
{k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d}, \ | |||
{k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, XXX, k2c, k2d}, \ | |||
{k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, XXX, k3b, XXX, k3d}, \ | |||
{k40, k41, k42, XXX, XXX, XXX, k46, XXX, XXX, XXX, k4a, k4b, k4c, k4d} \ | |||
} | |||
#endif |
@ -0,0 +1,79 @@ | |||
#include QMK_KEYBOARD_H | |||
// Used for SHIFT_ESC | |||
#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) | |||
// Each layer gets a name for readability, which is then used in the keymap matrix below. | |||
// The underscores don't mean anything - you can have a layer called STUFF or any other name. | |||
// Layer names don't all need to be of the same length, obviously, and you can also skip them | |||
// entirely and just use numbers. | |||
#define _BL 0 | |||
#define _FL 1 | |||
#define _______ KC_TRNS | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
/* Keymap _BL: (Base Layer) Default Layer | |||
* ,-----------------------------------------------------------. | |||
* |Esc~| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp | | |||
* |-----------------------------------------------------------| | |||
* |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \ | | |||
* |-----------------------------------------------------------| | |||
* |CAPS | A| S| D| F| G| H| J| K| L| ;| '|Return | | |||
* |-----------------------------------------------------------| | |||
* |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift | | |||
* |-----------------------------------------------------------| | |||
* |Ctrl|Gui |Alt | Space |Alt |Gui |FN |Ctrl | | |||
* `-----------------------------------------------------------' | |||
*/ | |||
[_BL] = KEYMAP_ANSI( | |||
F(0), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ | |||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC,KC_BSLS, \ | |||
KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_ENT, \ | |||
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, \ | |||
KC_LCTL, KC_LGUI,KC_LALT, KC_SPC, KC_RALT,KC_RGUI, MO(_FL),KC_RCTL), | |||
/* Keymap _FL: Function Layer | |||
*/ | |||
[_FL] = KEYMAP_ANSI( | |||
KC_GRV, _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,RESET, \ | |||
_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, BL_DEC, BL_INC,BL_TOGG, \ | |||
_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, \ | |||
_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, \ | |||
_______,_______,_______, _______, _______,_______,_______,_______), | |||
}; | |||
enum function_id { | |||
SHIFT_ESC, | |||
}; | |||
const uint16_t PROGMEM fn_actions[] = { | |||
[0] = ACTION_FUNCTION(SHIFT_ESC), | |||
}; | |||
void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { | |||
static uint8_t shift_esc_shift_mask; | |||
switch (id) { | |||
case SHIFT_ESC: | |||
shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; | |||
if (record->event.pressed) { | |||
if (shift_esc_shift_mask) { | |||
add_key(KC_GRV); | |||
send_keyboard_report(); | |||
} else { | |||
add_key(KC_ESC); | |||
send_keyboard_report(); | |||
} | |||
} else { | |||
if (shift_esc_shift_mask) { | |||
del_key(KC_GRV); | |||
send_keyboard_report(); | |||
} else { | |||
del_key(KC_ESC); | |||
send_keyboard_report(); | |||
} | |||
} | |||
break; | |||
} | |||
} |
@ -0,0 +1,67 @@ | |||
#include QMK_KEYBOARD_H | |||
// Used for SHIFT_ESC | |||
#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) | |||
// Each layer gets a name for readability, which is then used in the keymap matrix below. | |||
// The underscores don't mean anything - you can have a layer called STUFF or any other name. | |||
// Layer names don't all need to be of the same length, obviously, and you can also skip them | |||
// entirely and just use numbers. | |||
#define _BL 0 | |||
#define _FL 1 | |||
#define _______ KC_TRNS | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
/* Keymap _BL: (Base Layer) Default Layer | |||
*/ | |||
[_BL] = KEYMAP_ANSI( | |||
F(0), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ | |||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC,KC_BSLS, \ | |||
MO(_FL), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_ENT, \ | |||
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, \ | |||
KC_LCTL, KC_LGUI,KC_LALT, KC_SPC, KC_RALT,KC_RGUI, MO(_FL),KC_RCTL), | |||
/* Keymap _FL: Function Layer | |||
*/ | |||
[_FL] = KEYMAP_ANSI( | |||
KC_GRV, KC_F1,KC_F2,KC_F3,KC_F4,KC_F5,KC_F6,KC_F7,KC_F8,KC_F9,KC_F10,KC_F11,KC_F12,KC_DEL, \ | |||
_______,KC_MPRV,KC_MPLY,KC_MNXT,_______,_______,_______,KC_PGUP,KC_UP,KC_PGDN,KC_PSCR, KC_SLCK, KC_PAUS,_______, \ | |||
KC_CAPS,_______,KC_VOLD,KC_VOLU,KC_MUTE,_______,KC_HOME,KC_LEFT,KC_DOWN,KC_RGHT,KC_INS,KC_DEL,_______, \ | |||
_______,KC_APP,_______,_______,_______,_______,KC_END,_______,_______,_______,_______,_______, \ | |||
_______,_______,_______, _______, _______,_______,_______,_______), | |||
}; | |||
enum function_id { | |||
SHIFT_ESC, | |||
}; | |||
const uint16_t PROGMEM fn_actions[] = { | |||
[0] = ACTION_FUNCTION(SHIFT_ESC), | |||
}; | |||
void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { | |||
static uint8_t shift_esc_shift_mask; | |||
switch (id) { | |||
case SHIFT_ESC: | |||
shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; | |||
if (record->event.pressed) { | |||
if (shift_esc_shift_mask) { | |||
add_key(KC_GRV); | |||
send_keyboard_report(); | |||
} else { | |||
add_key(KC_ESC); | |||
send_keyboard_report(); | |||
} | |||
} else { | |||
if (shift_esc_shift_mask) { | |||
del_key(KC_GRV); | |||
send_keyboard_report(); | |||
} else { | |||
del_key(KC_ESC); | |||
send_keyboard_report(); | |||
} | |||
} | |||
break; | |||
} | |||
} |
@ -0,0 +1,85 @@ | |||
/* | |||
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio | |||
Licensed under the Apache License, Version 2.0 (the "License"); | |||
you may not use this file except in compliance with the License. | |||
You may obtain a copy of the License at | |||
http://www.apache.org/licenses/LICENSE-2.0 | |||
Unless required by applicable law or agreed to in writing, software | |||
distributed under the License is distributed on an "AS IS" BASIS, | |||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |||
See the License for the specific language governing permissions and | |||
limitations under the License. | |||
*/ | |||
/* | |||
* ST32F103xB memory setup for use with the originaljm60 bootloader. | |||
*/ | |||
MEMORY | |||
{ | |||
flash0 : org = 0x08009000, len = 128k - 0x9000 | |||
flash1 : org = 0x00000000, len = 0 | |||
flash2 : org = 0x00000000, len = 0 | |||
flash3 : org = 0x00000000, len = 0 | |||
flash4 : org = 0x00000000, len = 0 | |||
flash5 : org = 0x00000000, len = 0 | |||
flash6 : org = 0x00000000, len = 0 | |||
flash7 : org = 0x00000000, len = 0 | |||
ram0 : org = 0x20000000, len = 20k | |||
ram1 : org = 0x00000000, len = 0 | |||
ram2 : org = 0x00000000, len = 0 | |||
ram3 : org = 0x00000000, len = 0 | |||
ram4 : org = 0x00000000, len = 0 | |||
ram5 : org = 0x00000000, len = 0 | |||
ram6 : org = 0x00000000, len = 0 | |||
ram7 : org = 0x00000000, len = 0 | |||
} | |||
/* For each data/text section two region are defined, a virtual region | |||
and a load region (_LMA suffix).*/ | |||
/* Flash region to be used for exception vectors.*/ | |||
REGION_ALIAS("VECTORS_FLASH", flash0); | |||
REGION_ALIAS("VECTORS_FLASH_LMA", flash0); | |||
/* Flash region to be used for constructors and destructors.*/ | |||
REGION_ALIAS("XTORS_FLASH", flash0); | |||
REGION_ALIAS("XTORS_FLASH_LMA", flash0); | |||
/* Flash region to be used for code text.*/ | |||
REGION_ALIAS("TEXT_FLASH", flash0); | |||
REGION_ALIAS("TEXT_FLASH_LMA", flash0); | |||
/* Flash region to be used for read only data.*/ | |||
REGION_ALIAS("RODATA_FLASH", flash0); | |||
REGION_ALIAS("RODATA_FLASH_LMA", flash0); | |||
/* Flash region to be used for various.*/ | |||
REGION_ALIAS("VARIOUS_FLASH", flash0); | |||
REGION_ALIAS("VARIOUS_FLASH_LMA", flash0); | |||
/* Flash region to be used for RAM(n) initialization data.*/ | |||
REGION_ALIAS("RAM_INIT_FLASH_LMA", flash0); | |||
/* RAM region to be used for Main stack. This stack accommodates the processing | |||
of all exceptions and interrupts.*/ | |||
REGION_ALIAS("MAIN_STACK_RAM", ram0); | |||
/* RAM region to be used for the process stack. This is the stack used by | |||
the main() function.*/ | |||
REGION_ALIAS("PROCESS_STACK_RAM", ram0); | |||
/* RAM region to be used for data segment.*/ | |||
REGION_ALIAS("DATA_RAM", ram0); | |||
REGION_ALIAS("DATA_RAM_LMA", flash0); | |||
/* RAM region to be used for BSS segment.*/ | |||
REGION_ALIAS("BSS_RAM", ram0); | |||
/* RAM region to be used for the default heap.*/ | |||
REGION_ALIAS("HEAP_RAM", ram0); | |||
/* Generic rules inclusion.*/ | |||
INCLUDE rules.ld |
@ -0,0 +1,24 @@ | |||
/* | |||
Copyright 2012 Jun Wako <wakojun@gmail.com> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#include "hal.h" | |||
#include "led.h" | |||
void led_set(uint8_t usb_led) { | |||
} |
@ -0,0 +1,128 @@ | |||
#include <stdint.h> | |||
#include <stdbool.h> | |||
#include <string.h> | |||
#include "hal.h" | |||
#include "timer.h" | |||
#include "wait.h" | |||
#include "print.h" | |||
#include "matrix.h" | |||
/* | |||
* JM60 | |||
* Column pins are input with internal pull-down. Row pins are output and strobe with high. | |||
* Key is high or 1 when it turns on. | |||
* | |||
* col: { PTA15, PTC10, PTC11, PTC12, PTD2, PTB3, PTB4, PTB5, PTB6, PTB7, PTB8, PTB9, PTA2, PTA3 } | |||
* row: { PTB11, PTB10, PTB2, PTB1, PTB0} | |||
*/ | |||
/* matrix state(1:on, 0:off) */ | |||
static matrix_row_t matrix[MATRIX_ROWS]; | |||
static matrix_row_t matrix_debouncing[MATRIX_ROWS]; | |||
static bool debouncing = false; | |||
static uint16_t debouncing_time = 0; | |||
void matrix_init(void) | |||
{ | |||
//debug_matrix = true; | |||
/* Column(sense) */ | |||
palSetPadMode(GPIOA, 15, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOC, 10, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOC, 11, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOC, 12, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOD, 2, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOB, 3, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOB, 4, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOB, 5, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOB, 6, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOB, 7, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOB, 8, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOB, 9, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOA, 2, PAL_MODE_INPUT_PULLDOWN); | |||
palSetPadMode(GPIOA, 3, PAL_MODE_INPUT_PULLDOWN); | |||
/* Row(strobe) */ | |||
palSetPadMode(GPIOB, 11, PAL_MODE_OUTPUT_PUSHPULL); | |||
palSetPadMode(GPIOB, 10, PAL_MODE_OUTPUT_PUSHPULL); | |||
palSetPadMode(GPIOB, 2, PAL_MODE_OUTPUT_PUSHPULL); | |||
palSetPadMode(GPIOB, 1, PAL_MODE_OUTPUT_PUSHPULL); | |||
palSetPadMode(GPIOB, 0, PAL_MODE_OUTPUT_PUSHPULL); | |||
memset(matrix, 0, MATRIX_ROWS); | |||
memset(matrix_debouncing, 0, MATRIX_ROWS); | |||
} | |||
uint8_t matrix_scan(void) | |||
{ | |||
for (int row = 0; row < MATRIX_ROWS; row++) { | |||
matrix_row_t data = 0; | |||
// strobe row | |||
switch (row) { | |||
case 0: palSetPad(GPIOB, 11); break; | |||
case 1: palSetPad(GPIOB, 10); break; | |||
case 2: palSetPad(GPIOB, 2); break; | |||
case 3: palSetPad(GPIOB, 1); break; | |||
case 4: palSetPad(GPIOB, 0); break; | |||
} | |||
wait_us(20); // need wait to settle pin state | |||
// read col data: { PTA15, PTC10, PTC11, PTC12, PTD2, PTB3, PTB4, PTB5, PTB6, PTB7, PTB8, PTB9, PTA2, PTA3 } | |||
data = ((palReadPort(GPIOA) & 0x8000UL) >> 15) | // 0 | |||
((palReadPort(GPIOC) & 0x1C00UL) >> 9) | // 1, 2, 3 | |||
((palReadPort(GPIOD) & 0x0004UL) << 2) | // 4 | |||
((palReadPort(GPIOB) & 0x03F8UL) << 2) | // 5, 6, 7, 8, 9, 10, 11 | |||
((palReadPort(GPIOA) & 0x000CUL) << 10); // 12, 13 | |||
// un-strobe row | |||
switch (row) { | |||
case 0: palClearPad(GPIOB, 11); break; | |||
case 1: palClearPad(GPIOB, 10); break; | |||
case 2: palClearPad(GPIOB, 2); break; | |||
case 3: palClearPad(GPIOB, 1); break; | |||
case 4: palClearPad(GPIOB, 0); break; | |||
} | |||
if (matrix_debouncing[row] != data) { | |||
matrix_debouncing[row] = data; | |||
debouncing = true; | |||
debouncing_time = timer_read(); | |||
} | |||
} | |||
if (debouncing && timer_elapsed(debouncing_time) > DEBOUNCE) { | |||
for (int row = 0; row < MATRIX_ROWS; row++) { | |||
matrix[row] = matrix_debouncing[row]; | |||
} | |||
debouncing = false; | |||
} | |||
return 1; | |||
} | |||
bool matrix_is_on(uint8_t row, uint8_t col) | |||
{ | |||
return (matrix[row] & (1<<col)); | |||
} | |||
matrix_row_t matrix_get_row(uint8_t row) | |||
{ | |||
return matrix[row]; | |||
} | |||
void matrix_print(void) | |||
{ | |||
xprintf("\nr/c 01234567\n"); | |||
for (uint8_t row = 0; row < MATRIX_ROWS; row++) { | |||
xprintf("%X0: ", row); | |||
matrix_row_t data = matrix_get_row(row); | |||
for (int col = 0; col < MATRIX_COLS; col++) { | |||
if (data & (1<<col)) | |||
xprintf("1"); | |||
else | |||
xprintf("0"); | |||
} | |||
xprintf("\n"); | |||
} | |||
} |
@ -0,0 +1,209 @@ | |||
/* | |||
ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio | |||
Licensed under the Apache License, Version 2.0 (the "License"); | |||
you may not use this file except in compliance with the License. | |||
You may obtain a copy of the License at | |||
http://www.apache.org/licenses/LICENSE-2.0 | |||
Unless required by applicable law or agreed to in writing, software | |||
distributed under the License is distributed on an "AS IS" BASIS, | |||
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |||
See the License for the specific language governing permissions and | |||
limitations under the License. | |||
*/ | |||
#ifndef _MCUCONF_H_ | |||
#define _MCUCONF_H_ | |||
#define STM32F103_MCUCONF | |||
/* | |||
* STM32F103 drivers configuration. | |||
* The following settings override the default settings present in | |||
* the various device driver implementation headers. | |||
* Note that the settings for each driver only have effect if the whole | |||
* driver is enabled in halconf.h. | |||
* | |||
* IRQ priorities: | |||
* 15...0 Lowest...Highest. | |||
* | |||
* DMA priorities: | |||
* 0...3 Lowest...Highest. | |||
*/ | |||
/* | |||
* HAL driver system settings. | |||
*/ | |||
#define STM32_NO_INIT FALSE | |||
#define STM32_HSI_ENABLED TRUE | |||
#define STM32_LSI_ENABLED FALSE | |||
#define STM32_HSE_ENABLED TRUE | |||
#define STM32_LSE_ENABLED FALSE | |||
#define STM32_SW STM32_SW_PLL | |||
#define STM32_PLLSRC STM32_PLLSRC_HSE | |||
#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1 | |||
#define STM32_PLLMUL_VALUE 9 | |||
#define STM32_HPRE STM32_HPRE_DIV1 | |||
#define STM32_PPRE1 STM32_PPRE1_DIV2 | |||
#define STM32_PPRE2 STM32_PPRE2_DIV2 | |||
#define STM32_ADCPRE STM32_ADCPRE_DIV4 | |||
#define STM32_USB_CLOCK_REQUIRED TRUE | |||
#define STM32_USBPRE STM32_USBPRE_DIV1P5 | |||
#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK | |||
#define STM32_RTCSEL STM32_RTCSEL_HSEDIV | |||
#define STM32_PVD_ENABLE FALSE | |||
#define STM32_PLS STM32_PLS_LEV0 | |||
/* | |||
* ADC driver system settings. | |||
*/ | |||
#define STM32_ADC_USE_ADC1 FALSE | |||
#define STM32_ADC_ADC1_DMA_PRIORITY 2 | |||
#define STM32_ADC_ADC1_IRQ_PRIORITY 6 | |||
/* | |||
* CAN driver system settings. | |||
*/ | |||
#define STM32_CAN_USE_CAN1 FALSE | |||
#define STM32_CAN_CAN1_IRQ_PRIORITY 11 | |||
/* | |||
* EXT driver system settings. | |||
*/ | |||
#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI17_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 | |||
#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 | |||
/* | |||
* GPT driver system settings. | |||
*/ | |||
#define STM32_GPT_USE_TIM1 FALSE | |||
#define STM32_GPT_USE_TIM2 FALSE | |||
#define STM32_GPT_USE_TIM3 FALSE | |||
#define STM32_GPT_USE_TIM4 FALSE | |||
#define STM32_GPT_USE_TIM5 FALSE | |||
#define STM32_GPT_USE_TIM8 FALSE | |||
#define STM32_GPT_TIM1_IRQ_PRIORITY 7 | |||
#define STM32_GPT_TIM2_IRQ_PRIORITY 7 | |||
#define STM32_GPT_TIM3_IRQ_PRIORITY 7 | |||
#define STM32_GPT_TIM4_IRQ_PRIORITY 7 | |||
#define STM32_GPT_TIM5_IRQ_PRIORITY 7 | |||
#define STM32_GPT_TIM8_IRQ_PRIORITY 7 | |||
/* | |||
* I2C driver system settings. | |||
*/ | |||
#define STM32_I2C_USE_I2C1 FALSE | |||
#define STM32_I2C_USE_I2C2 FALSE | |||
#define STM32_I2C_BUSY_TIMEOUT 50 | |||
#define STM32_I2C_I2C1_IRQ_PRIORITY 5 | |||
#define STM32_I2C_I2C2_IRQ_PRIORITY 5 | |||
#define STM32_I2C_I2C1_DMA_PRIORITY 3 | |||
#define STM32_I2C_I2C2_DMA_PRIORITY 3 | |||
#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") | |||
/* | |||
* ICU driver system settings. | |||
*/ | |||
#define STM32_ICU_USE_TIM1 FALSE | |||
#define STM32_ICU_USE_TIM2 FALSE | |||
#define STM32_ICU_USE_TIM3 FALSE | |||
#define STM32_ICU_USE_TIM4 FALSE | |||
#define STM32_ICU_USE_TIM5 FALSE | |||
#define STM32_ICU_USE_TIM8 FALSE | |||
#define STM32_ICU_TIM1_IRQ_PRIORITY 7 | |||
#define STM32_ICU_TIM2_IRQ_PRIORITY 7 | |||
#define STM32_ICU_TIM3_IRQ_PRIORITY 7 | |||
#define STM32_ICU_TIM4_IRQ_PRIORITY 7 | |||
#define STM32_ICU_TIM5_IRQ_PRIORITY 7 | |||
#define STM32_ICU_TIM8_IRQ_PRIORITY 7 | |||
/* | |||
* PWM driver system settings. | |||
*/ | |||
#define STM32_PWM_USE_ADVANCED FALSE | |||
#define STM32_PWM_USE_TIM1 FALSE | |||
#define STM32_PWM_USE_TIM2 FALSE | |||
#define STM32_PWM_USE_TIM3 FALSE | |||
#define STM32_PWM_USE_TIM4 FALSE | |||
#define STM32_PWM_USE_TIM5 FALSE | |||
#define STM32_PWM_USE_TIM8 FALSE | |||
#define STM32_PWM_TIM1_IRQ_PRIORITY 7 | |||
#define STM32_PWM_TIM2_IRQ_PRIORITY 7 | |||
#define STM32_PWM_TIM3_IRQ_PRIORITY 7 | |||
#define STM32_PWM_TIM4_IRQ_PRIORITY 7 | |||
#define STM32_PWM_TIM5_IRQ_PRIORITY 7 | |||
#define STM32_PWM_TIM8_IRQ_PRIORITY 7 | |||
/* | |||
* RTC driver system settings. | |||
*/ | |||
#define STM32_RTC_IRQ_PRIORITY 15 | |||
/* | |||
* SERIAL driver system settings. | |||
*/ | |||
#define STM32_SERIAL_USE_USART1 FALSE | |||
#define STM32_SERIAL_USE_USART2 FALSE | |||
#define STM32_SERIAL_USE_USART3 FALSE | |||
#define STM32_SERIAL_USE_UART4 FALSE | |||
#define STM32_SERIAL_USE_UART5 FALSE | |||
#define STM32_SERIAL_USART1_PRIORITY 12 | |||
#define STM32_SERIAL_USART2_PRIORITY 12 | |||
#define STM32_SERIAL_USART3_PRIORITY 12 | |||
#define STM32_SERIAL_UART4_PRIORITY 12 | |||
#define STM32_SERIAL_UART5_PRIORITY 12 | |||
/* | |||
* SPI driver system settings. | |||
*/ | |||
#define STM32_SPI_USE_SPI1 FALSE | |||
#define STM32_SPI_USE_SPI2 FALSE | |||
#define STM32_SPI_USE_SPI3 FALSE | |||
#define STM32_SPI_SPI1_DMA_PRIORITY 1 | |||
#define STM32_SPI_SPI2_DMA_PRIORITY 1 | |||
#define STM32_SPI_SPI3_DMA_PRIORITY 1 | |||
#define STM32_SPI_SPI1_IRQ_PRIORITY 10 | |||
#define STM32_SPI_SPI2_IRQ_PRIORITY 10 | |||
#define STM32_SPI_SPI3_IRQ_PRIORITY 10 | |||
#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") | |||
/* | |||
* ST driver system settings. | |||
*/ | |||
#define STM32_ST_IRQ_PRIORITY 8 | |||
#define STM32_ST_USE_TIMER 2 | |||
/* | |||
* UART driver system settings. | |||
*/ | |||
#define STM32_UART_USE_USART1 FALSE | |||
#define STM32_UART_USE_USART2 FALSE | |||
#define STM32_UART_USE_USART3 FALSE | |||
#define STM32_UART_USART1_IRQ_PRIORITY 12 | |||
#define STM32_UART_USART2_IRQ_PRIORITY 12 | |||
#define STM32_UART_USART3_IRQ_PRIORITY 12 | |||
#define STM32_UART_USART1_DMA_PRIORITY 0 | |||
#define STM32_UART_USART2_DMA_PRIORITY 0 | |||
#define STM32_UART_USART3_DMA_PRIORITY 0 | |||
#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") | |||
/* | |||
* USB driver system settings. | |||
*/ | |||
#define STM32_USB_USE_USB1 TRUE | |||
#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE | |||
#define STM32_USB_USB1_HP_IRQ_PRIORITY 13 | |||
#define STM32_USB_USB1_LP_IRQ_PRIORITY 14 | |||
#endif /* _MCUCONF_H_ */ |
@ -0,0 +1,27 @@ | |||
JM60 | |||
======== | |||
A compact 60% keyboard with full RGB led support. | |||
Keyboard Maintainer: QMK Community | |||
Hardware Supported: JM60 | |||
Hardware Availability: https://kbdfans.myshopify.com/ (is no longer sold) | |||
Make example for this keyboard (after setting up your build environment): | |||
make jm60-default-bin | |||
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information. | |||
## Flashing Instructions | |||
1) from the `qmk_firmware` directory run: | |||
``` | |||
$ make jm60-default-bin | |||
``` | |||
2) rename 'jm60_default.bin' to 'jm60_default.firmware' | |||
3) Press 'R' and reconnect the keyboard. | |||
4) Start the original Configuration Tool and flash 'jm60_default.bin' |
@ -0,0 +1,56 @@ | |||
# project specific files | |||
SRC = matrix.c \ | |||
led.c | |||
## chip/board settings | |||
# - the next two should match the directories in | |||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) | |||
MCU_FAMILY = STM32 | |||
MCU_SERIES = STM32F1xx | |||
# Linker script to use | |||
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ | |||
# or <this_dir>/ld/ | |||
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC | |||
MCU_LDSCRIPT = jm60_bootloader | |||
# Startup code to use | |||
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ | |||
MCU_STARTUP = stm32f1xx | |||
# Board: it should exist either in <chibios>/os/hal/boards/ | |||
# or <this_dir>/boards | |||
BOARD = JM60_BOARD | |||
# Cortex version | |||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 | |||
MCU = cortex-m3 | |||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 | |||
# I.e. 6 for Teensy LC; 7 for Teensy 3.x | |||
ARMV = 7 | |||
# Vector table for application | |||
# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ | |||
# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB | |||
#OPT_DEFS = -DCORTEX_VTOR_INIT=0x00001000 | |||
OPT_DEFS = | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration | |||
## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.) | |||
MOUSEKEY_ENABLE = no # Mouse keys | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
CONSOLE_ENABLE = no # Console for debug | |||
COMMAND_ENABLE = no # Commands for debug and configuration | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE = yes # USB Nkey Rollover | |||
CUSTOM_MATRIX = yes # Custom matrix file | |||
BACKLIGHT_ENABLE = no | |||
VISUALIZER_ENABLE = no | |||
#LED_DRIVER = is31fl3731c | |||
#LED_WIDTH = 16 | |||
#LED_HEIGHT = 5 |