@ -1,70 +1,3 @@ | |||
# Target file name (without extension). | |||
# project specific files | |||
SRC = led.c | |||
# MCU name | |||
MCU = atmega32u2 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend | |||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,66 @@ | |||
# Target file name (without extension). | |||
# project specific files | |||
SRC = led.c | |||
# MCU name | |||
MCU = atmega32u2 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend | |||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA |
@ -1,70 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,66 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,74 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,70 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 |
@ -1,73 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,69 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend |
@ -1,88 +1,3 @@ | |||
ifdef TEENSY2 | |||
OPT_DEFS += -DATREUS_TEENSY2 | |||
ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex | |||
else | |||
OPT_DEFS += -DATREUS_ASTAR | |||
OPT_DEFS += -DCATERINA_BOOTLOADER | |||
ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ | |||
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) | |||
endif | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
USB ?= /dev/cu.usbmodem1411 | |||
upload: build | |||
$(ATREUS_UPLOAD_COMMAND) | |||
endif |
@ -0,0 +1,82 @@ | |||
ifdef TEENSY2 | |||
OPT_DEFS += -DATREUS_TEENSY2 | |||
ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex | |||
else | |||
OPT_DEFS += -DATREUS_ASTAR | |||
OPT_DEFS += -DCATERINA_BOOTLOADER | |||
ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ | |||
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) | |||
endif | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
USB ?= /dev/cu.usbmodem1411 | |||
upload: build | |||
$(ATRUES_UPLOAD_COMMAND) |
@ -1,72 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,67 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,14 +1,5 @@ | |||
SUBPROJECT_DEFAULT = stm32_f072_onekey | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control | |||
CONSOLE_ENABLE ?= yes # Console for debug | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
CUSTOM_MATRIX ?= yes # Custom matrix file | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,8 @@ | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control | |||
CONSOLE_ENABLE ?= yes # Console for debug | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
CUSTOM_MATRIX ?= yes # Custom matrix file |
@ -1,109 +1,5 @@ | |||
#---------------------------------------------------------------------------- | |||
# On command line: | |||
# | |||
# make all = Make software. | |||
# | |||
# make clean = Clean out built project files. | |||
# | |||
# make coff = Convert ELF to AVR COFF. | |||
# | |||
# make extcoff = Convert ELF to AVR Extended COFF. | |||
# | |||
# make program = Download the hex file to the device. | |||
# Please customize your programmer settings(PROGRAM_CMD) | |||
# | |||
# make teensy = Download the hex file to the device, using teensy_loader_cli. | |||
# (must have teensy_loader_cli installed). | |||
# | |||
# make dfu = Download the hex file to the device, using dfu-programmer (must | |||
# have dfu-programmer installed). | |||
# | |||
# make flip = Download the hex file to the device, using Atmel FLIP (must | |||
# have Atmel FLIP installed). | |||
# | |||
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer | |||
# (must have dfu-programmer installed). | |||
# | |||
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP | |||
# (must have Atmel FLIP installed). | |||
# | |||
# make debug = Start either simulavr or avarice as specified for debugging, | |||
# with avr-gdb or avr-insight as the front end for debugging. | |||
# | |||
# make filename.s = Just compile filename.c into the assembler code only. | |||
# | |||
# make filename.i = Create a preprocessed source file for use in submitting | |||
# bug reports to the GCC project. | |||
# | |||
# To rebuild project do "make clean" then "make all". | |||
#---------------------------------------------------------------------------- | |||
SUBPROJECT_DEFAULT = rev2 | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to no to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
AUDIO_ENABLE ?= no | |||
RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,103 @@ | |||
#---------------------------------------------------------------------------- | |||
# On command line: | |||
# | |||
# make all = Make software. | |||
# | |||
# make clean = Clean out built project files. | |||
# | |||
# make coff = Convert ELF to AVR COFF. | |||
# | |||
# make extcoff = Convert ELF to AVR Extended COFF. | |||
# | |||
# make program = Download the hex file to the device. | |||
# Please customize your programmer settings(PROGRAM_CMD) | |||
# | |||
# make teensy = Download the hex file to the device, using teensy_loader_cli. | |||
# (must have teensy_loader_cli installed). | |||
# | |||
# make dfu = Download the hex file to the device, using dfu-programmer (must | |||
# have dfu-programmer installed). | |||
# | |||
# make flip = Download the hex file to the device, using Atmel FLIP (must | |||
# have Atmel FLIP installed). | |||
# | |||
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer | |||
# (must have dfu-programmer installed). | |||
# | |||
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP | |||
# (must have Atmel FLIP installed). | |||
# | |||
# make debug = Start either simulavr or avarice as specified for debugging, | |||
# with avr-gdb or avr-insight as the front end for debugging. | |||
# | |||
# make filename.s = Just compile filename.c into the assembler code only. | |||
# | |||
# make filename.i = Create a preprocessed source file for use in submitting | |||
# bug reports to the GCC project. | |||
# | |||
# To rebuild project do "make clean" then "make all". | |||
#---------------------------------------------------------------------------- | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
AUDIO_ENABLE ?= no | |||
RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,76 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= yes # Audio output on port C6 | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,70 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= yes # Audio output on port C6 |
@ -1,70 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
# MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
# EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
# CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
# COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable numpad's backlight functionality | |||
RGBLIGHT_ENABLE ?= yes | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,65 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
# MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
# EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
# CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
# COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable numpad's backlight functionality | |||
RGBLIGHT_ENABLE ?= yes | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,34 +1,5 @@ | |||
#---------------------------------------------------------------------------- | |||
# On command line: | |||
# | |||
# make = Make software. | |||
# | |||
# make clean = Clean out built project files. | |||
# | |||
# That's pretty much all you need. To compile, always go make clean, | |||
# followed by make. | |||
# | |||
# For advanced users only: | |||
# make teensy = Download the hex file to the device, using teensy_loader_cli. | |||
# (must have teensy_loader_cli installed). | |||
# | |||
#---------------------------------------------------------------------------- | |||
SUBPROJECT_DEFAULT = ez | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
CUSTOM_MATRIX ?= yes # Custom matrix file for the ErgoDox EZ | |||
SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= yes # Unicode | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,28 @@ | |||
#---------------------------------------------------------------------------- | |||
# On command line: | |||
# | |||
# make = Make software. | |||
# | |||
# make clean = Clean out built project files. | |||
# | |||
# That's pretty much all you need. To compile, always go make clean, | |||
# followed by make. | |||
# | |||
# For advanced users only: | |||
# make teensy = Download the hex file to the device, using teensy_loader_cli. | |||
# (must have teensy_loader_cli installed). | |||
# | |||
#---------------------------------------------------------------------------- | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
CUSTOM_MATRIX ?= yes # Custom matrix file for the ErgoDox EZ | |||
SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= yes # Unicode |
@ -1,74 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
# CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
# COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
include ../../Makefile | |||
endif | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,68 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
# CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
# COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,3 +1,3 @@ | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -1,65 +1,3 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend | |||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
ifndef QUANTUM_DIR | |||
include ../../../Makefile | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -1,90 +1,3 @@ | |||
# project specific files | |||
SRC = matrix.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
#OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# as per original hasu settings | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
CUSTOM_MATRIX ?= yes # Custom matrix file for the HHKB | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
ifneq (, $(findstring yes, $(HHKB_JP))) | |||
OPT_DEFS += -DHHKB_JP | |||
endif | |||
debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION | |||
debug-on: all | |||
debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT | |||
debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS)) | |||
debug-off: all | |||
endif |
@ -0,0 +1,84 @@ | |||
# project specific files | |||
SRC = matrix.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
#OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# as per original hasu settings | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
CUSTOM_MATRIX ?= yes # Custom matrix file for the HHKB | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifneq (, $(findstring yes, $(HHKB_JP))) | |||
OPT_DEFS += -DHHKB_JP | |||
endif | |||
debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION | |||
debug-on: all | |||
debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT | |||
debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS)) | |||
debug-off: all |
@ -1,70 +1,3 @@ | |||
# project specific files | |||
SRC = matrix.c \ | |||
led.c | |||
## chip/board settings | |||
# - the next two should match the directories in | |||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) | |||
# - For Teensies, FAMILY = KINETIS and SERIES is either | |||
# KL2x (LC) or K20x (3.0,3.1,3.2). | |||
# - For Infinity KB, SERIES = K20x | |||
MCU_FAMILY = KINETIS | |||
MCU_SERIES = K20x | |||
# Linker script to use | |||
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ | |||
# or <this_dir>/ld/ | |||
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC | |||
# - LDSCRIPT = | |||
# - MKL26Z64 for Teensy LC | |||
# - MK20DX128 for Teensy 3.0 | |||
# - MK20DX256 for Teensy 3.1 and 3.2 | |||
# - MK20DX128BLDR4 for Infinity with Kiibohd bootloader | |||
MCU_LDSCRIPT = MK20DX128BLDR4 | |||
# Startup code to use | |||
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ | |||
# - STARTUP = | |||
# - kl2x for Teensy LC | |||
# - k20x5 for Teensy 3.0 and Infinity KB | |||
# - k20x7 for Teensy 3.1 and 3.2 | |||
MCU_STARTUP = k20x5 | |||
# Board: it should exist either in <chibios>/os/hal/boards/ | |||
# or <this_dir>/boards | |||
# - BOARD = | |||
# - PJRC_TEENSY_LC for Teensy LC | |||
# - PJRC_TEENSY_3 for Teensy 3.0 | |||
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 | |||
# - MCHCK_K20 for Infinity KB | |||
BOARD = MCHCK_K20 | |||
# Cortex version | |||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 | |||
MCU = cortex-m4 | |||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 | |||
# I.e. 6 for Teensy LC; 7 for Teensy 3.x | |||
ARMV = 7 | |||
# Vector table for application | |||
# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ | |||
# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB | |||
OPT_DEFS = -DCORTEX_VTOR_INIT=0x00001000 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration | |||
## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control | |||
CONSOLE_ENABLE ?= yes # Console for debug | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
CUSTOM_MATRIX ?= yes # Custom matrix file | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,66 @@ | |||
# project specific files | |||
SRC = matrix.c \ | |||
led.c | |||
## chip/board settings | |||
# - the next two should match the directories in | |||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) | |||
# - For Teensies, FAMILY = KINETIS and SERIES is either | |||
# KL2x (LC) or K20x (3.0,3.1,3.2). | |||
# - For Infinity KB, SERIES = K20x | |||
MCU_FAMILY = KINETIS | |||
MCU_SERIES = K20x | |||
# Linker script to use | |||
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ | |||
# or <this_dir>/ld/ | |||
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC | |||
# - LDSCRIPT = | |||
# - MKL26Z64 for Teensy LC | |||
# - MK20DX128 for Teensy 3.0 | |||
# - MK20DX256 for Teensy 3.1 and 3.2 | |||
# - MK20DX128BLDR4 for Infinity with Kiibohd bootloader | |||
MCU_LDSCRIPT = MK20DX128BLDR4 | |||
# Startup code to use | |||
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ | |||
# - STARTUP = | |||
# - kl2x for Teensy LC | |||
# - k20x5 for Teensy 3.0 and Infinity KB | |||
# - k20x7 for Teensy 3.1 and 3.2 | |||
MCU_STARTUP = k20x5 | |||
# Board: it should exist either in <chibios>/os/hal/boards/ | |||
# or <this_dir>/boards | |||
# - BOARD = | |||
# - PJRC_TEENSY_LC for Teensy LC | |||
# - PJRC_TEENSY_3 for Teensy 3.0 | |||
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 | |||
# - MCHCK_K20 for Infinity KB | |||
BOARD = MCHCK_K20 | |||
# Cortex version | |||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 | |||
MCU = cortex-m4 | |||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 | |||
# I.e. 6 for Teensy LC; 7 for Teensy 3.x | |||
ARMV = 7 | |||
# Vector table for application | |||
# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ | |||
# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB | |||
OPT_DEFS = -DCORTEX_VTOR_INIT=0x00001000 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration | |||
## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control | |||
CONSOLE_ENABLE ?= yes # Console for debug | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
CUSTOM_MATRIX ?= yes # Custom matrix file |
@ -1,71 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
# NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,67 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
# NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,76 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,70 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 |
@ -1,79 +1,3 @@ | |||
## Project specific files | |||
SRC= matrix.c | |||
# MCU name | |||
MCU = at90usb1286 | |||
#MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=1024 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= no | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE = no # Audio output should be port E6, current quantum library hardcodes C6, which we use for programming | |||
CUSTOM_MATRIX=yes # need to do our own thing with the matrix | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,73 @@ | |||
## Project specific files | |||
SRC= matrix.c | |||
# MCU name | |||
MCU = at90usb1286 | |||
#MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=1024 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= no | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE = no # Audio output should be port E6, current quantum library hardcodes C6, which we use for programming | |||
CUSTOM_MATRIX=yes # need to do our own thing with the matrix |
@ -1,78 +1,3 @@ | |||
SRC += matrix.c \ | |||
i2c.c \ | |||
split_util.c \ | |||
serial.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= yes # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
CUSTOM_MATRIX = yes | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,74 @@ | |||
SRC += matrix.c \ | |||
i2c.c \ | |||
split_util.c \ | |||
serial.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= yes # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
CUSTOM_MATRIX = yes |
@ -1,74 +1,3 @@ | |||
SRC = led.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
RGBLIGHT_ENABLE ?=yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality (+1150) | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,69 @@ | |||
SRC = led.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
RGBLIGHT_ENABLE ?=yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality (+1150) | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,74 +1,5 @@ | |||
SUBPROJECT_DEFAULT = rev4 | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,67 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend |
@ -1,73 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif |
@ -0,0 +1,69 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change to "no" to disable the options, or define them in the Makefile in | |||
# the appropriate keymap folder that will get included automatically | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend |
@ -1,74 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,68 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality | |||
# MIDI_ENABLE ?= YES # MIDI controls | |||
# UNICODE_ENABLE ?= YES # Unicode | |||
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,75 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,69 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 |
@ -1,70 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,66 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) | |||
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID |
@ -1,75 +1,3 @@ | |||
SRC = matrix.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega16u2 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= no # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= no # Commands for debug and configuration | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= no # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
CUSTOM_MATRIX = yes | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,70 @@ | |||
SRC = matrix.c | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega16u2 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= no # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= no # Console for debug(+400) | |||
COMMAND_ENABLE ?= no # Commands for debug and configuration | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE ?= no # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality | |||
MIDI_ENABLE ?= no # MIDI controls | |||
AUDIO_ENABLE ?= no | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
CUSTOM_MATRIX = yes |
@ -1,75 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,69 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 |