diff --git a/keyboards/garlicboard/config.h b/keyboards/garlicboard/config.h
new file mode 100644
index 00000000000..8f70d521ad3
--- /dev/null
+++ b/keyboards/garlicboard/config.h
@@ -0,0 +1,58 @@
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Tom Meyer
+#define PRODUCT         GarlicBoard
+#define DESCRIPTION     GarlicBoard
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 17
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { B0, B1, B2, B3 }
+#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B6, B5, B4, D7, D6, D4, D5, D2, D1, D0, B7 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION ROW2COL
+
+/* number of backlight levels */
+
+#ifdef BACKLIGHT_PIN
+#define BACKLIGHT_LEVELS 0
+#endif
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* prevent stuck modifiers */
+#define PREVENT_STUCK_MODIFIERS
+
+
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 0
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif
+
+#endif
\ No newline at end of file
diff --git a/keyboards/garlicboard/garlicboard.c b/keyboards/garlicboard/garlicboard.c
new file mode 100644
index 00000000000..52517688362
--- /dev/null
+++ b/keyboards/garlicboard/garlicboard.c
@@ -0,0 +1,65 @@
+#include "garlicboard.h"
+#include "led.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+	matrix_init_user();
+	led_init_ports();
+};
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+	matrix_scan_user();
+};
+
+void led_init_ports(void) {
+    // * Set our LED pins as output
+    DDRE |= (1<<6);
+    DDRD |= (1<<3);
+    DDRC |= (1<<6);
+    DDRC |= (1<<7);
+}
+
+void led_set_kb(uint8_t usb_led) {
+    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+        PORTE |= (1<<6);
+    } else {
+        PORTE &= ~(1<<6);
+    }
+
+    if (usb_led & (1<<USB_LED_NUM_LOCK)) {
+        PORTD |= (1<<3);
+    } else {
+        PORTD &= ~(1<<3);
+    }
+}
+
+uint32_t layer_state_set_kb(uint32_t state) {
+    if (state & (1<<4)) {
+        PORTC |= (1<<6);
+    } else {
+        PORTC &= ~(1<<6);
+    }
+
+    if (state & (1<<2)) {
+        PORTC |= (1<<7);
+    } else {
+        PORTC &= ~(1<<7);
+    }
+
+    if (state & (1<<5)) {
+        PORTE |= (1<<6);
+        PORTD |= (1<<3);
+        PORTC |= (1<<6);
+        PORTC |= (1<<7);
+    } else {
+        PORTE &= ~(1<<6);
+        PORTD &= ~(1<<3);
+        PORTC &= ~(1<<6);
+        PORTC &= ~(1<<7);
+    }
+
+    return state;
+}
\ No newline at end of file
diff --git a/keyboards/garlicboard/garlicboard.h b/keyboards/garlicboard/garlicboard.h
new file mode 100644
index 00000000000..ed452e60a90
--- /dev/null
+++ b/keyboards/garlicboard/garlicboard.h
@@ -0,0 +1,18 @@
+#ifndef GARLICBOARD_H
+#define GARLICBOARD_H
+
+#include "quantum.h"
+
+#define KEYMAP( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, K015, K016, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110,       K112, K113, K114, K115, K116, \
+	K200,       K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213, K214, K215, K216, \
+	K300, K301, K302, K303,       K305,       K307,       K309, K310, K311, K312, K313, K314, K315, K316  \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014,  K015,  K016 }, \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  KC_NO, K112,  K113,  K114,  K115,  K116 }, \
+	{ K200,  KC_NO, K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  K214,  K215,  K216 }, \
+	{ K300,  K301,  K302,  K303,  KC_NO, K305,  KC_NO, K307,  KC_NO, K309,  K310,  K311,  K312,  K313,  K314,  K315,  K316 }  \
+}
+
+#endif
\ No newline at end of file
diff --git a/keyboards/garlicboard/keymaps/default/keymap.c b/keyboards/garlicboard/keymaps/default/keymap.c
new file mode 100644
index 00000000000..0633e42b10b
--- /dev/null
+++ b/keyboards/garlicboard/keymaps/default/keymap.c
@@ -0,0 +1,41 @@
+#include "garlicboard.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	KEYMAP(
+		KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_MINS, KC_BSPC, KC_P7, KC_P8, KC_P9, KC_PMNS, 
+		KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, KC_P4, KC_P5, KC_P6, KC_PPLS, 
+		KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_LSFT, KC_P1, KC_P2, KC_P3, KC_PENT, 
+		MO(3), KC_LCTL, KC_LALT, KC_LGUI, MO(2), KC_SPC, KC_RGUI, KC_RALT, KC_RCTL, MO(2), KC_P0, KC_P0, KC_PDOT, TG(1)),
+
+	KEYMAP(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_INS, KC_HOME, KC_PGUP, KC_NO, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_DEL, KC_END, KC_PGDN, KC_NO, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_ESC, KC_UP, KC_SPC, KC_ENT, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS),
+
+	KEYMAP(
+		KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_EQL, KC_TRNS, KC_VOLD, KC_MUTE, KC_VOLU, KC_PSLS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BSLS, KC_LBRC, KC_RBRC, KC_QUOT, KC_TRNS, KC_MPRV, KC_MPLY, KC_MNXT, KC_PAST, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_SLSH, KC_NO, KC_MSTP, KC_NO, KC_TAB, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PWR, TG(4), KC_NLCK, TG(5)),
+
+	KEYMAP(
+		KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, 
+		KC_CAPS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_F5, KC_F6, KC_F7, KC_F8, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_F9, KC_F10, KC_F11, KC_F12, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_F13, KC_F14, KC_F15, KC_F16),
+
+	KEYMAP(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_SPC, MO(2), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+	KEYMAP(
+		KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, 
+		KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, 
+		KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, 
+		KC_TRNS, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_TRNS, KC_NO, KC_NO, KC_NO, KC_TRNS),
+
+};
\ No newline at end of file
diff --git a/keyboards/garlicboard/rules.mk b/keyboards/garlicboard/rules.mk
new file mode 100644
index 00000000000..58798b761fd
--- /dev/null
+++ b/keyboards/garlicboard/rules.mk
@@ -0,0 +1,56 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = no	# Console for debug(+400)
+COMMAND_ENABLE = no    # Commands for debug and configuration
+SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no  # Enable keyboard backlight functionality
+AUDIO_ENABLE = no
+RGBLIGHT_ENABLE = no
\ No newline at end of file