* Added Zlant support * Uses LAYOUT and identifies individual layers * Removed deprecated =? usage on rules.mk * Adds readme for Zlant keyboard and its default layout * Fixed LAYOUT constant * Minor zlant readme formatting fixpull/3030/head
@ -0,0 +1,58 @@ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xFEED | |||
#define PRODUCT_ID 0x6060 | |||
#define DEVICE_VER 0x0001 | |||
#define MANUFACTURER Matthew Cordier | |||
#define PRODUCT Zlant | |||
#define DESCRIPTION keyboard firmware for Zlant | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 4 | |||
#define MATRIX_COLS 12 | |||
/* key matrix pins */ | |||
#define MATRIX_ROW_PINS { B0, B1, D4, D5 } | |||
#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B7, D1, D2, D3, B3, B2 } | |||
#define UNUSED_PINS | |||
/* COL2ROW or ROW2COL */ | |||
#define DIODE_DIRECTION COL2ROW | |||
/* number of backlight levels */ | |||
#ifdef BACKLIGHT_PIN | |||
#define BACKLIGHT_LEVELS 0 | |||
#endif | |||
/* Set 0 if debouncing isn't needed */ | |||
#define DEBOUNCING_DELAY 5 | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
/* key combination for command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
/* prevent stuck modifiers */ | |||
#define PREVENT_STUCK_MODIFIERS | |||
#define RGB_DI_PIN D6 | |||
#ifdef RGB_DI_PIN | |||
#define RGBLIGHT_ANIMATIONS | |||
#define RGBLED_NUM 12 | |||
#define RGBLIGHT_HUE_STEP 8 | |||
#define RGBLIGHT_SAT_STEP 8 | |||
#define RGBLIGHT_VAL_STEP 8 | |||
#endif | |||
#endif |
@ -0,0 +1,20 @@ | |||
#include QMK_KEYBOARD_H | |||
#define BASE 0 | |||
#define FN 1 | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
[BASE] = LAYOUT( | |||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, | |||
KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, | |||
KC_ESC, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT, | |||
RGB_HUI, RGB_HUD, KC_LGUI, KC_LALT, KC_LSFT, KC_SPC, KC_SPC, MO(1), KC_LEFT, KC_DOWN, KC_UP, KC_RGHT), | |||
[FN] = LAYOUT( | |||
KC_TRNS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_TRNS, | |||
KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS, | |||
KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_PGUP, KC_HOME, KC_TRNS, KC_TRNS, | |||
RGB_VAI, RGB_VAD, RESET, KC_PSCR, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGDN, KC_END, KC_TRNS, KC_DEL) | |||
}; |
@ -0,0 +1,5 @@ | |||
![Zlant Layout Image](https://i.imgur.com/Siz8qsL.jpg) | |||
# Default Zlant Layout | |||
This is the default layout that comes flashed on the Zlant prototype. |
@ -0,0 +1,17 @@ | |||
# Zlant | |||
![Zlant](https://i.imgur.com/Siz8qsL.jpg) | |||
A compact 40% inspired by the Plank with a staggered layout instead. | |||
Keyboard Maintainer: [Felipe Coury](https://github.com/fcoury) | |||
Hardware Supported: Zlant Prototype PCB | |||
Hardware Availability: Group buy soon | |||
Make example for this keyboard (after setting up your build environment): | |||
make zlant:default | |||
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information. |
@ -0,0 +1,56 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = no # Commands for debug and configuration | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |||
AUDIO_ENABLE = no | |||
RGBLIGHT_ENABLE = yes |
@ -0,0 +1 @@ | |||
#include "zlant.h" |
@ -0,0 +1,18 @@ | |||
#ifndef KB_H | |||
#define KB_H | |||
#include "quantum.h" | |||
#define LAYOUT( \ | |||
K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, \ | |||
K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, \ | |||
K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, \ | |||
K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311 \ | |||
) { \ | |||
{ K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011 }, \ | |||
{ K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111 }, \ | |||
{ K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211 }, \ | |||
{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311 } \ | |||
} | |||
#endif |