|
|
|
@ -0,0 +1,383 @@ |
|
|
|
/* Name: usbconfig.h |
|
|
|
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers |
|
|
|
* Author: Christian Starkjohann |
|
|
|
* Creation Date: 2005-04-01 |
|
|
|
* Tabsize: 4 |
|
|
|
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH |
|
|
|
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) |
|
|
|
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $ |
|
|
|
*/ |
|
|
|
|
|
|
|
#pragma once |
|
|
|
|
|
|
|
#include "config.h" |
|
|
|
|
|
|
|
/* |
|
|
|
General Description: |
|
|
|
This file is an example configuration (with inline documentation) for the USB |
|
|
|
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is |
|
|
|
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may |
|
|
|
wire the lines to any other port, as long as D+ is also wired to INT0 (or any |
|
|
|
other hardware interrupt, as long as it is the highest level interrupt, see |
|
|
|
section at the end of this file). |
|
|
|
*/ |
|
|
|
|
|
|
|
/* ---------------------------- Hardware Config ---------------------------- */ |
|
|
|
|
|
|
|
#define USB_CFG_IOPORTNAME D |
|
|
|
/* This is the port where the USB bus is connected. When you configure it to |
|
|
|
* "B", the registers PORTB, PINB and DDRB will be used. |
|
|
|
*/ |
|
|
|
#define USB_CFG_DMINUS_BIT 3 |
|
|
|
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. |
|
|
|
* This may be any bit in the port. |
|
|
|
*/ |
|
|
|
#define USB_CFG_DPLUS_BIT 2 |
|
|
|
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. |
|
|
|
* This may be any bit in the port. Please note that D+ must also be connected |
|
|
|
* to interrupt pin INT0! [You can also use other interrupts, see section |
|
|
|
* "Optional MCU Description" below, or you can connect D- to the interrupt, as |
|
|
|
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the |
|
|
|
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame |
|
|
|
* markers every millisecond.] |
|
|
|
*/ |
|
|
|
#define USB_CFG_CLOCK_KHZ (F_CPU/1000) |
|
|
|
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, |
|
|
|
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code |
|
|
|
* require no crystal, they tolerate +/- 1% deviation from the nominal |
|
|
|
* frequency. All other rates require a precision of 2000 ppm and thus a |
|
|
|
* crystal! |
|
|
|
* Since F_CPU should be defined to your actual clock rate anyway, you should |
|
|
|
* not need to modify this setting. |
|
|
|
*/ |
|
|
|
#define USB_CFG_CHECK_CRC 0 |
|
|
|
/* Define this to 1 if you want that the driver checks integrity of incoming |
|
|
|
* data packets (CRC checks). CRC checks cost quite a bit of code size and are |
|
|
|
* currently only available for 18 MHz crystal clock. You must choose |
|
|
|
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option. |
|
|
|
*/ |
|
|
|
|
|
|
|
/* ----------------------- Optional Hardware Config ------------------------ */ |
|
|
|
|
|
|
|
/* #define USB_CFG_PULLUP_IOPORTNAME D */ |
|
|
|
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of |
|
|
|
* V+, you can connect and disconnect the device from firmware by calling |
|
|
|
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h). |
|
|
|
* This constant defines the port on which the pullup resistor is connected. |
|
|
|
*/ |
|
|
|
/* #define USB_CFG_PULLUP_BIT 4 */ |
|
|
|
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined |
|
|
|
* above) where the 1.5k pullup resistor is connected. See description |
|
|
|
* above for details. |
|
|
|
*/ |
|
|
|
|
|
|
|
/* --------------------------- Functional Range ---------------------------- */ |
|
|
|
|
|
|
|
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1 |
|
|
|
/* Define this to 1 if you want to compile a version with two endpoints: The |
|
|
|
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint |
|
|
|
* number). |
|
|
|
*/ |
|
|
|
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1 |
|
|
|
/* Define this to 1 if you want to compile a version with three endpoints: The |
|
|
|
* default control endpoint 0, an interrupt-in endpoint 3 (or the number |
|
|
|
* configured below) and a catch-all default interrupt-in endpoint as above. |
|
|
|
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature. |
|
|
|
*/ |
|
|
|
#define USB_CFG_EP3_NUMBER 3 |
|
|
|
/* If the so-called endpoint 3 is used, it can now be configured to any other |
|
|
|
* endpoint number (except 0) with this macro. Default if undefined is 3. |
|
|
|
*/ |
|
|
|
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */ |
|
|
|
/* The above macro defines the startup condition for data toggling on the |
|
|
|
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1. |
|
|
|
* Since the token is toggled BEFORE sending any data, the first packet is |
|
|
|
* sent with the oposite value of this configuration! |
|
|
|
*/ |
|
|
|
#define USB_CFG_IMPLEMENT_HALT 0 |
|
|
|
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature |
|
|
|
* for endpoint 1 (interrupt endpoint). Although you may not need this feature, |
|
|
|
* it is required by the standard. We have made it a config option because it |
|
|
|
* bloats the code considerably. |
|
|
|
*/ |
|
|
|
#define USB_CFG_SUPPRESS_INTR_CODE 0 |
|
|
|
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't |
|
|
|
* want to send any data over them. If this macro is defined to 1, functions |
|
|
|
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if |
|
|
|
* you need the interrupt-in endpoints in order to comply to an interface |
|
|
|
* (e.g. HID), but never want to send any data. This option saves a couple |
|
|
|
* of bytes in flash memory and the transmit buffers in RAM. |
|
|
|
*/ |
|
|
|
#define USB_CFG_IS_SELF_POWERED 0 |
|
|
|
/* Define this to 1 if the device has its own power supply. Set it to 0 if the |
|
|
|
* device is powered from the USB bus. |
|
|
|
*/ |
|
|
|
#define USB_CFG_IMPLEMENT_FN_WRITE 1 |
|
|
|
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out |
|
|
|
* transfers. Set it to 0 if you don't need it and want to save a couple of |
|
|
|
* bytes. |
|
|
|
*/ |
|
|
|
#define USB_CFG_IMPLEMENT_FN_READ 0 |
|
|
|
/* Set this to 1 if you need to send control replies which are generated |
|
|
|
* "on the fly" when usbFunctionRead() is called. If you only want to send |
|
|
|
* data from a static buffer, set it to 0 and return the data from |
|
|
|
* usbFunctionSetup(). This saves a couple of bytes. |
|
|
|
*/ |
|
|
|
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 |
|
|
|
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. |
|
|
|
* You must implement the function usbFunctionWriteOut() which receives all |
|
|
|
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number |
|
|
|
* can be found in 'usbRxToken'. |
|
|
|
*/ |
|
|
|
#define USB_CFG_HAVE_FLOWCONTROL 0 |
|
|
|
/* Define this to 1 if you want flowcontrol over USB data. See the definition |
|
|
|
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in |
|
|
|
* usbdrv.h. |
|
|
|
*/ |
|
|
|
#define USB_CFG_DRIVER_FLASH_PAGE 0 |
|
|
|
/* If the device has more than 64 kBytes of flash, define this to the 64 k page |
|
|
|
* where the driver's constants (descriptors) are located. Or in other words: |
|
|
|
* Define this to 1 for boot loaders on the ATMega128. |
|
|
|
*/ |
|
|
|
#define USB_CFG_LONG_TRANSFERS 0 |
|
|
|
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes |
|
|
|
* in a single control-in or control-out transfer. Note that the capability |
|
|
|
* for long transfers increases the driver size. |
|
|
|
*/ |
|
|
|
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */ |
|
|
|
/* This macro is a hook if you want to do unconventional things. If it is |
|
|
|
* defined, it's inserted at the beginning of received message processing. |
|
|
|
* If you eat the received message and don't want default processing to |
|
|
|
* proceed, do a return after doing your things. One possible application |
|
|
|
* (besides debugging) is to flash a status LED on each packet. |
|
|
|
*/ |
|
|
|
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */ |
|
|
|
/* This macro is a hook if you need to know when an USB RESET occurs. It has |
|
|
|
* one parameter which distinguishes between the start of RESET state and its |
|
|
|
* end. |
|
|
|
*/ |
|
|
|
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */ |
|
|
|
/* This macro (if defined) is executed when a USB SET_ADDRESS request was |
|
|
|
* received. |
|
|
|
*/ |
|
|
|
#define USB_COUNT_SOF 1 |
|
|
|
/* define this macro to 1 if you need the global variable "usbSofCount" which |
|
|
|
* counts SOF packets. This feature requires that the hardware interrupt is |
|
|
|
* connected to D- instead of D+. |
|
|
|
*/ |
|
|
|
/* #ifdef __ASSEMBLER__ |
|
|
|
* macro myAssemblerMacro |
|
|
|
* in YL, TCNT0 |
|
|
|
* sts timer0Snapshot, YL |
|
|
|
* endm |
|
|
|
* #endif |
|
|
|
* #define USB_SOF_HOOK myAssemblerMacro |
|
|
|
* This macro (if defined) is executed in the assembler module when a |
|
|
|
* Start Of Frame condition is detected. It is recommended to define it to |
|
|
|
* the name of an assembler macro which is defined here as well so that more |
|
|
|
* than one assembler instruction can be used. The macro may use the register |
|
|
|
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages |
|
|
|
* immediately after an SOF pulse may be lost and must be retried by the host. |
|
|
|
* What can you do with this hook? Since the SOF signal occurs exactly every |
|
|
|
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in |
|
|
|
* designs running on the internal RC oscillator. |
|
|
|
* Please note that Start Of Frame detection works only if D- is wired to the |
|
|
|
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! |
|
|
|
*/ |
|
|
|
#define USB_CFG_CHECK_DATA_TOGGLING 0 |
|
|
|
/* define this macro to 1 if you want to filter out duplicate data packets |
|
|
|
* sent by the host. Duplicates occur only as a consequence of communication |
|
|
|
* errors, when the host does not receive an ACK. Please note that you need to |
|
|
|
* implement the filtering yourself in usbFunctionWriteOut() and |
|
|
|
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable |
|
|
|
* for each control- and out-endpoint to check for duplicate packets. |
|
|
|
*/ |
|
|
|
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 |
|
|
|
/* define this macro to 1 if you want the function usbMeasureFrameLength() |
|
|
|
* compiled in. This function can be used to calibrate the AVR's RC oscillator. |
|
|
|
*/ |
|
|
|
#define USB_USE_FAST_CRC 0 |
|
|
|
/* The assembler module has two implementations for the CRC algorithm. One is |
|
|
|
* faster, the other is smaller. This CRC routine is only used for transmitted |
|
|
|
* messages where timing is not critical. The faster routine needs 31 cycles |
|
|
|
* per byte while the smaller one needs 61 to 69 cycles. The faster routine |
|
|
|
* may be worth the 32 bytes bigger code size if you transmit lots of data and |
|
|
|
* run the AVR close to its limit. |
|
|
|
*/ |
|
|
|
|
|
|
|
/* -------------------------- Device Description --------------------------- */ |
|
|
|
|
|
|
|
#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF) |
|
|
|
/* USB vendor ID for the device, low byte first. If you have registered your |
|
|
|
* own Vendor ID, define it here. Otherwise you may use one of obdev's free |
|
|
|
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules! |
|
|
|
* *** IMPORTANT NOTE *** |
|
|
|
* This template uses obdev's shared VID/PID pair for Vendor Class devices |
|
|
|
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand |
|
|
|
* the implications! |
|
|
|
*/ |
|
|
|
#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF) |
|
|
|
/* This is the ID of the product, low byte first. It is interpreted in the |
|
|
|
* scope of the vendor ID. If you have registered your own VID with usb.org |
|
|
|
* or if you have licensed a PID from somebody else, define it here. Otherwise |
|
|
|
* you may use one of obdev's free shared VID/PID pairs. See the file |
|
|
|
* USB-IDs-for-free.txt for details! |
|
|
|
* *** IMPORTANT NOTE *** |
|
|
|
* This template uses obdev's shared VID/PID pair for Vendor Class devices |
|
|
|
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand |
|
|
|
* the implications! |
|
|
|
*/ |
|
|
|
#define USB_CFG_DEVICE_VERSION (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF) |
|
|
|
/* Version number of the device: Minor number first, then major number. |
|
|
|
*/ |
|
|
|
#define USB_CFG_VENDOR_NAME 'H', 'N', 'B' |
|
|
|
#define USB_CFG_VENDOR_NAME_LEN 3 |
|
|
|
/* These two values define the vendor name returned by the USB device. The name |
|
|
|
* must be given as a list of characters under single quotes. The characters |
|
|
|
* are interpreted as Unicode (UTF-16) entities. |
|
|
|
* If you don't want a vendor name string, undefine these macros. |
|
|
|
* ALWAYS define a vendor name containing your Internet domain name if you use |
|
|
|
* obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for |
|
|
|
* details. |
|
|
|
*/ |
|
|
|
#define USB_CFG_DEVICE_NAME 'D', 'B', '6', '3', 'H', 'S' |
|
|
|
#define USB_CFG_DEVICE_NAME_LEN 6 |
|
|
|
/* Same as above for the device name. If you don't want a device name, undefine |
|
|
|
* the macros. See the file USB-IDs-for-free.txt before you assign a name if |
|
|
|
* you use a shared VID/PID. |
|
|
|
*/ |
|
|
|
/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */ |
|
|
|
/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */ |
|
|
|
/* Same as above for the serial number. If you don't want a serial number, |
|
|
|
* undefine the macros. |
|
|
|
* It may be useful to provide the serial number through other means than at |
|
|
|
* compile time. See the section about descriptor properties below for how |
|
|
|
* to fine tune control over USB descriptors such as the string descriptor |
|
|
|
* for the serial number. |
|
|
|
*/ |
|
|
|
#define USB_CFG_DEVICE_CLASS 0 |
|
|
|
#define USB_CFG_DEVICE_SUBCLASS 0 |
|
|
|
/* See USB specification if you want to conform to an existing device class. |
|
|
|
* Class 0xff is "vendor specific". |
|
|
|
*/ |
|
|
|
#define USB_CFG_INTERFACE_CLASS 3 /* HID */ |
|
|
|
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */ |
|
|
|
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */ |
|
|
|
/* See USB specification if you want to conform to an existing device class or |
|
|
|
* protocol. The following classes must be set at interface level: |
|
|
|
* HID class is 3, no subclass and protocol required (but may be useful!) |
|
|
|
* CDC class is 2, use subclass 2 and protocol 1 for ACM |
|
|
|
*/ |
|
|
|
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 |
|
|
|
/* Define this to the length of the HID report descriptor, if you implement |
|
|
|
* an HID device. Otherwise don't define it or define it to 0. |
|
|
|
* If you use this define, you must add a PROGMEM character array named |
|
|
|
* "usbHidReportDescriptor" to your code which contains the report descriptor. |
|
|
|
* Don't forget to keep the array and this define in sync! |
|
|
|
*/ |
|
|
|
|
|
|
|
/* #define USB_PUBLIC static */ |
|
|
|
/* Use the define above if you #include usbdrv.c instead of linking against it. |
|
|
|
* This technique saves a couple of bytes in flash memory. |
|
|
|
*/ |
|
|
|
|
|
|
|
/* ------------------- Fine Control over USB Descriptors ------------------- */ |
|
|
|
/* If you don't want to use the driver's default USB descriptors, you can |
|
|
|
* provide our own. These can be provided as (1) fixed length static data in |
|
|
|
* flash memory, (2) fixed length static data in RAM or (3) dynamically at |
|
|
|
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more |
|
|
|
* information about this function. |
|
|
|
* Descriptor handling is configured through the descriptor's properties. If |
|
|
|
* no properties are defined or if they are 0, the default descriptor is used. |
|
|
|
* Possible properties are: |
|
|
|
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched |
|
|
|
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is |
|
|
|
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if |
|
|
|
* you want RAM pointers. |
|
|
|
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found |
|
|
|
* in static memory is in RAM, not in flash memory. |
|
|
|
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash), |
|
|
|
* the driver must know the descriptor's length. The descriptor itself is |
|
|
|
* found at the address of a well known identifier (see below). |
|
|
|
* List of static descriptor names (must be declared PROGMEM if in flash): |
|
|
|
* char usbDescriptorDevice[]; |
|
|
|
* char usbDescriptorConfiguration[]; |
|
|
|
* char usbDescriptorHidReport[]; |
|
|
|
* char usbDescriptorString0[]; |
|
|
|
* int usbDescriptorStringVendor[]; |
|
|
|
* int usbDescriptorStringDevice[]; |
|
|
|
* int usbDescriptorStringSerialNumber[]; |
|
|
|
* Other descriptors can't be provided statically, they must be provided |
|
|
|
* dynamically at runtime. |
|
|
|
* |
|
|
|
* Descriptor properties are or-ed or added together, e.g.: |
|
|
|
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18)) |
|
|
|
* |
|
|
|
* The following descriptors are defined: |
|
|
|
* USB_CFG_DESCR_PROPS_DEVICE |
|
|
|
* USB_CFG_DESCR_PROPS_CONFIGURATION |
|
|
|
* USB_CFG_DESCR_PROPS_STRINGS |
|
|
|
* USB_CFG_DESCR_PROPS_STRING_0 |
|
|
|
* USB_CFG_DESCR_PROPS_STRING_VENDOR |
|
|
|
* USB_CFG_DESCR_PROPS_STRING_PRODUCT |
|
|
|
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER |
|
|
|
* USB_CFG_DESCR_PROPS_HID |
|
|
|
* USB_CFG_DESCR_PROPS_HID_REPORT |
|
|
|
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver) |
|
|
|
* |
|
|
|
* Note about string descriptors: String descriptors are not just strings, they |
|
|
|
* are Unicode strings prefixed with a 2 byte header. Example: |
|
|
|
* int serialNumberDescriptor[] = { |
|
|
|
* USB_STRING_DESCRIPTOR_HEADER(6), |
|
|
|
* 'S', 'e', 'r', 'i', 'a', 'l' |
|
|
|
* }; |
|
|
|
*/ |
|
|
|
|
|
|
|
#define USB_CFG_DESCR_PROPS_DEVICE 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC |
|
|
|
//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_STRINGS 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_STRING_0 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC |
|
|
|
//#define USB_CFG_DESCR_PROPS_HID 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC |
|
|
|
//#define USB_CFG_DESCR_PROPS_HID_REPORT 0 |
|
|
|
#define USB_CFG_DESCR_PROPS_UNKNOWN 0 |
|
|
|
|
|
|
|
#define usbMsgPtr_t unsigned short |
|
|
|
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to |
|
|
|
* a scalar type here because gcc generates slightly shorter code for scalar |
|
|
|
* arithmetics than for pointer arithmetics. Remove this define for backward |
|
|
|
* type compatibility or define it to an 8 bit type if you use data in RAM only |
|
|
|
* and all RAM is below 256 bytes (tiny memory model in IAR CC). |
|
|
|
*/ |
|
|
|
|
|
|
|
/* ----------------------- Optional MCU Description ------------------------ */ |
|
|
|
|
|
|
|
/* The following configurations have working defaults in usbdrv.h. You |
|
|
|
* usually don't need to set them explicitly. Only if you want to run |
|
|
|
* the driver on a device which is not yet supported or with a compiler |
|
|
|
* which is not fully supported (such as IAR C) or if you use a differnt |
|
|
|
* interrupt than INT0, you may have to define some of these. |
|
|
|
*/ |
|
|
|
/* #define USB_INTR_CFG MCUCR */ |
|
|
|
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */ |
|
|
|
/* #define USB_INTR_CFG_CLR 0 */ |
|
|
|
/* #define USB_INTR_ENABLE GIMSK */ |
|
|
|
/* #define USB_INTR_ENABLE_BIT INT0 */ |
|
|
|
/* #define USB_INTR_PENDING GIFR */ |
|
|
|
/* #define USB_INTR_PENDING_BIT INTF0 */ |
|
|
|
/* #define USB_INTR_VECTOR INT0_vect */ |
|
|
|
|
|
|
|
/* Set INT1 for D- falling edge to count SOF */ |
|
|
|
/* #define USB_INTR_CFG EICRA */ |
|
|
|
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10)) |
|
|
|
/* #define USB_INTR_CFG_CLR 0 */ |
|
|
|
/* #define USB_INTR_ENABLE EIMSK */ |
|
|
|
#define USB_INTR_ENABLE_BIT INT1 |
|
|
|
/* #define USB_INTR_PENDING EIFR */ |
|
|
|
#define USB_INTR_PENDING_BIT INTF1 |
|
|
|
#define USB_INTR_VECTOR INT1_vect |
Hung DO
4 years ago
Drashna Jaelre